This identifies the driver for the Atmel HUSB2 Device Controller,
as integrated into the first AVR32 chip, the AT32AP700.
From: Håvard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as837) fixes several mistakes in the AIO interface of the
gadgetfs driver:
The ki_retry method is not supposed to do a put on the kiocb.
The extra call to aio_put_req() causes memory corruption.
(Note: This call was removed before, by patch as691, and then
mysteriously re-introduced later.)
Even if a read transfer is cancelled, we can and should send
to the user all the data that did manage to get transferred.
Testing for AIO cancellation in the I/O completion handler
is both racy and (now) unnecessary. aio_complete() does its
own checking, in a safe manner.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resolve an initizlization issue that could come up if the userspace
driver wrote invalid descriptors to a dual-speed device.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves a race in gadgetfs associated with changing device/ep0
when processing control requests. The fix is to change that state
earlier, when the control response is issued, so there's no window
in which userspace could see the wrong state; and enlarge the scope
of the spinlock during the ep0 request completion handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simplifies event reading by eliminating arithmetic and being
more direct/obvious, and tweaks some debug messages slightly.
The math elimination will change timings, sometimes enough to
allow a race to appear.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor gadgetfs cleanups:
- EP0 state constants become consistently STATE_DEV_* rather than
sometimes omitting the "DEV_"; STATE_EP_* were already consistent.
- Comment that ep0 state is protected by the spinlock, and update
code that was neglecting that rule.
None of this is expected to change behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the AT91 UDC driver's handling of wakeup events:
- Fix a bug in the original scheme, which was never updated after
the {enable,disable}_irq_wake() semantics were updated to address
refcounting issues (i.e. behave for shared irqs).
- Couple handling of both type of wakeup events, to be more direct. The
controller can be source of wakeup events for cases like bus reset
and USB resume. On some boards, VBUS sensing is also IRQ driven.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadgetfs had a mode in which endpoint descriptors were written by the user
program before connection. This mode had some bugs, and hasn't seen much
(if any) use. This patch removes that mode, leaving the mode of operation
where the user program waits for endpoint 0 to report a SET_CONFIGURATION,
and only then configures the endpoints.
From: "Phil Endecott" <spam_from_usb_devel@chezphil.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some whitespace bugs in gadgetfs (mostly from someone's
patch updating the AIO support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Went looking through some usb stuff and found some unnecessary casts in
file_storage.c This is part of the KernelJanitors TODO list.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that minor tweaks to the "CDC Subset" support in the Ethernet
gadget driver, just updating a config descriptor, let it be automagically
recognized by a Windows driver supported by MCCI.
This patch adds those descriptors, so systems using PXA 255 processors
(like Gumstix etc) can interop with those commercial MS-Windows drivers.
This is a Good Thing since Microsoft's RNDIS code has bugginess issues,
which are unfortunately compounded by "won't fix" issues as well as "the
published specs are incomplete and wrong" issues. Being able to talk to
the MCCI driver gives Windows users another connectivity option. (MCCI
also has CDC Ethernet drivers, which can help most non-PXA processors.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves <linux/usb_ch9.h> to <linux/usb/ch9.h> to reduce some of the
clutter of usb header files.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resync the omap_udc driver with the latest from the Linux-OMAP tree.
Changes include DMA API updates (it builds again!), clock/pm updates,
minor bugfixes, whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch performs additional checks in at91_udc, just in case of
some spurious interrupts or device enumeration.
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch zeroes some variables when usb_gadget_register_driver()
fails. gadgetfs does a dummy registration to get the name of the USB
driver and then waits for user-land driver. If someone plugs the cable
in the meantime, bad things happen, because at91_udc has been left in
inconsistent state.
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows gadget drivers that support high speed (e.g. gadgetfs)
to work properly with at91_udc.
Fix suggested by Milan Svoboda in
http://marc.theaimsgroup.com/?l=linux-usb-devel&m=115822184711817
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an update to the AT91 USB Device (Gadget) driver.
Adds support for the Atmel AT91SAM9260 and AT91SAM9261 processors. The
only difference is how they handle the pullup pin.
[Patch from Patrice Vilchez]
Need to clear any pending USB Device interrupts before registering the
interrupt handler. The bootloader might have been using the USB Device
port. [Patch from Peer Georgi]
VBUS detection is handled by a GPIO interrupt which only triggers on a
change. Is is therefore necessary to read the current VBUS state
explicitly at startup. [Patch from Peer Georgi]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an update to the AT91 USB Device (Gadget) driver.
The base I/O address provided in the platform_device resources is now
ioremap()'ed instead of using a statically mapped memory area. This
helps portability to the newer AT91sam926x processors.
The major change is that we now have to pass a 'struct at91_udc'
parameter to at91_udp_read() and at91_udp_write().
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow gadget drivers to omit the unbind() method. When they're
statically linked, that's an appropriate memory saving tweak.
Similarly, provide consistent/simpler handling for a should-not-happen
error case: removing a peripheral controller driver when a gadget
driver is still loaded. Such code dates back to early versions of the
first implementation of the gadget API, and has never been triggered.
Includes relevant section annotation fixs for gmidi.c, file_storage.c,
and serial.c; we don't yet have an "init or exit" annotation. Also
some whitespace fixes in gmidi.c (space at EOL, before tabs, etc).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0. No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response. Otherwise deferred responses are impossible.
This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup/clarification in the ethernet gadget driver, using standard
calls to test for Ethernet multicast and broadcast addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This was apparently missed by the move to the generic IRQ code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It would fail the compile due to the newly added error checking testing
a bad macro for a "return value" unless USB_GADGET_DEBUG_FILES was
enabled.
Pointed out by Stephen Hemminger.
Acked-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch vectorizes aio_read() and aio_write() methods to prepare for
collapsing all aio & vectored operations into one interface - which is
aio_read()/aio_write().
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Michael Holzheu <HOLZHEU@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Strictly speaking, the Valid bit in SCSI sense data is supposed to
be set only when the Information field contains a valid number. This
patch (as793) turns off the Valid bit when the Information field
hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as758) fixes the "warn-unused-result" messages in dummy-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the code handling dma-coherent buffer allocations, basically
reusing code from the musb_hdrc driver. Instead of trying to work around two
significant limitations of the dma framework (memory wastage for buffers
smaller than a page, and inconsistency between calling context requirements
for allocation and free) this just works around one of them (the latter).
So count this as two steps forward (bugfixes: the latter issue could cause
errors on some platforms, and some MIPS changes broke code for the former),
and one step back (increasing cross-platform memory wastage).
Plus linelength and whitespace fixes; and minor data segment shrinkage.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adjust dev->dev_lock spinlock lock/unlock calls to be safe for SMP case.
Otherwise the following sequence may lead to a deadlock in SMP case:
gs_send()->usb_ep_queue()
->(in case a request is satisfied immediatly) gs_write_complete()
for ex for pxa2xx_udc.c:
usb_ep_queue()->pxa2xx_ep_queue()->write_fifo()->done()->gs_write_complete()
(through req.complete pointer)
Signed-off-by: Eugeny S. Mints <emints@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For ep0out transfers (rare), be sure to copy the right data to userspace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For systems using the Mentor HDRC controllers we get better TX DMA throughput
if we can avoid falling back to PIO to write zero length packets ... so tell
the driver to avoid ZLPs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of the ongoing program to flatten out the HCD bus-glue layer,
this patch (as771b) eliminates the hcpriv, release, and kref fields
from struct usb_bus. hcpriv and release were not being used for
anything worthwhile, and kref has been moved into the enclosing
usb_hcd structure.
Along with those changes, the patch gets rid of usb_bus_get and
usb_bus_put, replacing them with usb_get_hcd and usb_put_hcd.
The one interesting aspect is that the dev_set_drvdata call was
removed from usb_put_hcd, where it clearly doesn't belong. This means
the driver private data won't get reset to NULL. It shouldn't cause
any problems, since the private data is undefined when no driver is
bound.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This tiny patch fixes a typo in drivers/usb/gadget/Kconfig. The typo
is present in 2.6.18-rc4 and in the corresponding -mm tree (and AFAIK,
FYI and FWIW was present in previous kernel versions as well).
From: Jules Villard <jvillard@ens-lyon.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
another gcc 4.1 signdness warning:
drivers/usb/gadget/ether.c:2028: warning: comparison of unsigned expression < 0 is always false
length is assigned the value of usb_ep_queue() which returns an int.
Directly after this it is checked for < 0, which can never be true. Making
length an int makes the error check work again.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I spotted this during my tests with -rt on arm. The -rt patch contains
some better tools
to diagnose problems with locks and some other things...
Original code tries to take semaphore in BUG_ON and then free the memory
with this semaphore.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add poll() support to gadgetfs ep0
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Making structs const prevents accidental bugs and with the proper debug
options they're protected against corruption.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is glue between the USB gadget interface
and the ALSA MIDI interface. It allows us to appear
as a MIDI Streaming device to a host system on the
other end of a USB cable.
This includes linux/usb/audio.h and linux/usb/midi.h
containing definitions from the relevant USB specifications
for USB audio and USB MIDI devices.
The following changes have been made since the first RFC
posting:
* Bug fixes to endpoint handling.
* Workaround for USB_REQ_SET_CONFIGURATION handling,
not understood yet.
* Added SND and SND_RAWMIDI dependencies in Kconfig.
* Moved usb_audio.h and usb_midi.h to usb/*.h
* Added module parameters for ALSA card index and id.
* Added module parameters for USB descriptor IDs and strings.
* Removed some unneeded stuff inherited from zero.c, more to go.
* Provide DECLARE_* macros for the variable-length structs.
* Use kmalloc instead of usb_ep_alloc_buffer.
* Limit source to 80 columns.
* Return actual error code instead of -ENOMEM in a few places.
Signed-off-by: Ben Williamson <ben.williamson@greyinnovation.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds mutex protection to ep_release.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes ep_config to return correct value. Without patch
ep_config returns submitted lenght minus 4 on succes. With this
patch applied, whole submitted lenght is returned.
ep_config parses submitted data and if buffer starts with (int) 1
it is parsed, otherwise error is reported. Problem is that ep_config
returns size of buffer minus 4 on success. I think that size of buffer
should be returned instead, because there were no problems and
all data were processed.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves spin_lock (&dev->lock) before first use of dev.
I think that test to the state of device should be protected with
this spin_lock...
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allows compiling g_ether in and fixes a typo with MUSB_HDRC
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the PXA 25x UDC board-independent infrastructure for VBUS sensing
and the D+ pullup. The original code evolved from rather bizarre support on
Intel's "Lubbock" reference hardware, so that on more sensible hardware it
doesn't work as well as it could/should.
The change is just to teach the UDC driver how to use built-in PXA GPIO pins
directly. This reduces the amount of board-specfic object code needed, and
enables the use of a VBUS sensing IRQ on boards (like Gumstix) that have one.
With VBUS sensing, the UDC is unclocked until a host is actually connected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This eliminates the i_blksize field from struct inode. Filesystems that want
to provide a per-inode st_blksize can do so by providing their own getattr
routine instead of using the generic_fillattr() function.
Note that some filesystems were providing pretty much random (and incorrect)
values for i_blksize.
[bunk@stusta.de: cleanup]
[akpm@osdl.org: generic_fillattr() fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new spinlock debug code turned up a spinlock recursion bug in the
Ethernet gadget driver on a disconnect path; it would show up with any
UDC driver where the cancellation of active requests was synchronous,
rather than e.g. delayed until a controller's completion IRQ.
That recursion is fixed here by creating and using a new spinlock to
protect the relevant lists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as756) fixes a bug in dummy-hcd found by the lockdep
checker. In one of the code paths, the driver did not disable
interrupts before calling a request completion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB=m, USB_GADGET=y, the option USB_GADGET_DUMMY_HCD mustn't be
offered since selecting it results in a compile error.
This patch fixes kernel Bugzilla #6534 reported by Toralf Förster.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UDC updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, UDC can be a source of system wakeup events
(host resume, device connect/disconnect, etc)
- Fix IRQ storming issues, seemingly related to clock disabling
changes that went in a while back
And minor cleanups, especially whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent section changes broke gadget builds on some platforms. This patch
is the best fix that's available until better section markings exist:
- There's a lot of cleanup code that gets used in both init and exit paths;
stop marking it as "__exit".
(Best fix for this would be an "__init_or_exit" section marking, putting
the cleanup in __init when __exit sections get discarded else in __exit.)
- Stop marking the use-once probe routines as "__init" since references
to those routines are not allowed from driver structures. They're now
marked "__devinit", which in practice is a net lose.
(Best fix for this is likely to separate such use-once probe routines
from the driver structure ... but in general, all busses that aren't
hotpluggable will be forced to waste memory for all probe-only code.)
In general these broken section rules waste an average of two to four kBytes
per driver of code bloat ... because none of the relevant code can ever be
reused after module initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
This fixes pxa2xx_udc.c to include asm/arch/udc.h again to fix current
build breakage.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
[ forwarded by David Brownell <david-b@pacbell.net> ]
[ fixed to apply properly by Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A process flag to indicate whether we are doing sync io is incredibly
ugly. It also causes performance problems when one does a lot of async
io and then proceeds to sync it. Part of the io will go out as async,
and the other part as sync. This causes a disconnect between the
previously submitted io and the synced io. For io schedulers such as CFQ,
this will cause us lost merges and suboptimal behaviour in scheduling.
Remove PF_SYNCWRITE completely from the fsync/msync paths, and let
the O_DIRECT path just directly indicate that the writes are sync
by using WRITE_SYNC instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves <linux/usb_cdc.h> to <linux/usb/cdc.h> to reduce some of the
clutter of usb header files.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes extraneous whitespace from the Ethernet/RNDIS gadget driver.
It's all space-at-EOL, spaces-before-tabs, or tabs-then-spaces.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds IXP465 into the list of known devices and
adds IXP425 and IXP465 to the list of devices that have cfr. This
is not described in the hardware documentation, but without
it driver won't work.
Workaround (#if 1) that seemed to get rid of lost
status irqs is disabled for IXP4XX as it caused freezes
during testing of control messages. No lost irqs are
visible on IXP4XX.
Driver survived tests running over night without any
visible problems.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes compile errors when pxa2xx_udc is to be compiled
for ixp4xx platform.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes limitation which prevents use of drivers that support
speeds different that full speed.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by David Brownell, we know that IRQs are never
blocked when calling gs_close function. So the save/restore
IRQ flags are pointless.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When closing the device, the driver acquires/release twice the
port lock before/after waiting for the data to be completely
sent. Therefore it will dead lock.
This patch fixes it and also uses the generic scheduler services
for waiting for an event.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as692) fixes a few memory leaks in some unimportant error
pathways of the gadgetfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as691) fixes a few errors in the AIO interface for the
gadgetfs driver. Now requests will complete properly instead of hanging.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net2280 board has an annoying habit of surviving soft reboots with
interrupts enabled. This patch (as674) adds a shutdown routine to the
driver so that the board can be put in a quiescent state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as671) fixes a bug in the error pathway for the net2280
probe routine. A failure during probe will cause the driver to call
pci_get_drvdata before the corresponding pci_set_drvdata has been set.
The patch also does a kzalloc conversion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as670) adds a check for whether a shared IRQ was actually
generated by the net2280 device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as669) fixes a bug in the net2280 driver. Now it will
properly send zero-length packets on ep0 until the control status stage
occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as668) fixes a typo in net2280. The handler for 0-length
control-IN requests should check that the endpoint _isn't_ halted before
sending a 0-length packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move common definitions for NET2280 to <linux/usb/net2280.h>, so that I can
use them in prism54usb (it is not merged yet, but I plan to do it soon).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be sure to record the peripheral's ep0 maxpacket size BEFORE using
that to initialize the (high speed) device qualifier; that helps a
lot with USBCV testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AT91: the two USB drivers (OHCI, UDC) got out of sync with various
usbcore and driver model PM updates; fix.
Also minor fixes to ohci: whitespace/style, MODULE_ALIAS so coldplug works
using /sys/.../modalias, and turn off _both_ clocks during suspend.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fill OUT buffers with 0x55 before RX, so that controller driver
bugs that mangle data can be more readily detected during testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This catches up to a change in the Kconfig support for highspeed modes;
the change predated 2.6.10, and anyone using gadgetfs on a highspeed
device would see the kernel wrongly reject the alternate descriptors.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some patch broke short-OUT packet handling for net2280, making it report
illegal status values. This updates the status code so it's correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I submitted the wrong version of the patch teaching about the driver
for Mentor's Highspeed Dual Role Controller (HDRC), whoops! This
uses the right name for that driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap pointed out that there now is a module_param_array_named
macro available. This patch (as666) updates g_file_storage to make use of
it. It also adds a comment listing the specifications documents used in
the design of the driver's SCSI operation (at Pat LaVarre's request).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as664) adds a comment to file_storage.c, noting that the
driver is slightly non-portable because it assumes that a buffer
allocated for a bulk-in endpoint will also be useable for a bulk-out
endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm told that some UDC hardware may work better if it knows that
receiving a short packet should always cause an error. Accordingly,
this patch (as663) sets the short_not_ok flag for bulk-out transfers in
g_file_storage. Oddly enough, there are no circumstances where that
driver can legally receive a shorter-than-expected bulk-out packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch to gadgets/net2280.[ch] which adds support for the
net2282 controller. The original code was kindly provided by PLX
Technology, I just merged it with the current net2280 driver in the
kernel. Tested on 2.6.15.6, but only with 2282. I did the merge, so
that the behaviour for the 2280 is unaffected (except for short delays
for extra checks).
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for net2282 in net2280 driver.
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch converts drivers/usb to kzalloc usage.
Compile tested with allyes config.
I think there was a bug in drivers/usb/gadget/inode.c because
it used sizeof(*data) for the kmalloc() and sizeof(data) for
the memset(), since sizeof(data) just returns the size for a pointer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows you to set the iSerialNumber field in the
usb_device_descriptor structure for your USB ethernet gadget.
It also changes the parameters shown through sysfs so they're
no longer declared as __initdata, preventing potential oopses.
That's most useful for the Ethernet addresses, which may in
some cases be random "locally administered" addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds __init section annotations to gadget driver bind() routines to
remove calls from .text into .init sections (for endpoint autoconfig).
Likewise it adds __exit section annotations to their unbind() routines.
The specification of the gadget driver register/unregister functions is
updated to explicitly allow use of those sections.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds declarations for three USB peripheral controllers:
- Two high speed USB cores that can be licensed from Mentor Graphics
to be integrated into silicon:
* "musbhsfc" is for peripherals only, as found in for example the
IBM/AMCC 44EP processors.
* "musbhdrc" is OTG-capable (dual role), and is found in various
products including OMAP 2430 and the new DaVinci SOCs.
The "musbh" standing for "Mentor USB Highspeed", the rest standing
for "Function Controller" or "Dual Role Controller" (OTG-capable).
- The full speed controller on the FreeScale MPC8272.
Adding these definitions just allows gadget driver code to handle any
controller-specific logic; controller drivers are quite separate.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resove a minor FIXME: don't change MTU while RNDIS link is active,
the other end won't expect such things...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for the USB peripheral controller on AT91
(rm9200, eventually also sam9261 or uClinux) platforms.
More SOC support for Linux-USB ... an uncomplicated pure PIO driver.
It'd be worth using this as a model, if you're starting a driver
for some other peripheral controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote NDIS response to OID_GEN_SUPPORTED_LIST only allocated space
for the data attached to the reply, and not the reply structure
itself. This caused other kmalloc'd memory to be corrupted.
Signed-off-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a dead lock in lh7a40x udc driver. When the driver receive a
SET_FEATURE HALT request, the dev lock is taken by the interrupt
handler lh7a40x_udc_irq then the handler will call lh7a40x_set_halt
function which in its turn will try to acquire the dev lock.
Signed-off-by: Franck Bui-Huu <franck.bui-huu@innova-card.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes sure that the correct length is reported when freeing
a dma-coherent buffer; some platforms complain if that's wrong.
It also makes two parameters readonly in sysfs, as they're not
safe to change while tests are running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as622) makes gadgetfs set the "zero" flag for control-IN
responses, when the length of the response is shorter than the length of
the request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some reason alpha doesn't include <linux/dma-mapping.h> where other
architectures do; this makes net2280 include it explicitly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB gadget drivers make no use of these, remove the pointless
comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of ARRAY_SIZE. Some trailing whitespaces are also removed.
Patch is compile-tested on i386.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as613) moves the updates to hcd->state in the dummy_hcd
driver to where they now belong. It also uses the new
HC_FLAG_HW_ACCESSIBLE flag in a way that simulates a real PCI
controller, and it adds checks for attempts to resume the bus while the
controller is suspended or to suspend the controller while the bus is
active.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as612) removes the "volatile" declarations from the
file-storage gadget. It turns out that they aren't needed for anything
much; adding a few memory barriers does a sufficient job.
The patch also removes a wait_queue. Not much point having a queue when
only one task is ever going to be on it!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It looks like that the gs_serial module maybe sleep with spinlock in gs_close.
Sometimes, system hang when I remove the gs_serial module.
From: Fengwei Yin <xaityyy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent platform_device update has reintroduced into dummy_hcd.c the
dreaded dev->dev syndrome. This harkens back to when an earlier version
of that driver included the unforgettable line:
dev->dev.dev.driver_data = dev;
This patch (as602) renames the platform_device variables to "pdev", in
the hope of reducing confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as601) adds a proper reference count to the file-storage
gadget's main data structure, to keep track of references held by child
devices (LUNs in this case). Before this, the driver would wait for
each child to be released before unbinding.
While there's nothing really wrong with that (you can't create a hang by
doing "rmmod g_file_storage </sys/.../lun0/ro" since the open file will
prevent rmmod from running), the code might as well follow the standard
procedures. Besides, this shrinks the size of the structure by a few
words... :-)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure the the device_driver and usb_gadget_driver
have their .owner fields initialised to associate
the module owner to the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is put into suspend mode, the current drawn from VBUS
has to be less than 500 uA. Some transceivers need to be put into a
special power-saving mode to accomplish this, and won't have a separate
OTG driver handling that.
This adds a suspend method to the "otg_transceiver" struct -- misnamed,
it's not only for OTG -- and calls it from the OMAP UDC driver.
Signed-off-by: Juha Yrj?l? <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change to make DMA work two bytes at a time omitted an important
tweak that affects the file_storage gadget: it needs to recognize when
the host writes an odd number of bytes. (The network layer ignores
such extra bytes.)
This patch resolves that issue by checking the relevant bit and adjusting
the rx byte count, so that for example a legal 13 byte request doesn't
morph into an illegal 14 byte one any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code. It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume. These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.
It also takes David's advice about removing the layer of bus glue, where
those methods are called. And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as575) fixes an unlikely race in the g_file_storage driver.
The problem can occur only when the driver is unbound before its
initialization routine has finished.
I also took the opportunity to replace kmalloc/memset with kzalloc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as566) converts the File-Storage gadget over to the kthread
API. The new code doesn't use kthread_stop because the control thread
needs to terminate asynchronously when it receives a signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/file_storage.c | 32 +++++++++++++-------------------
1 file changed, 13 insertions(+), 19 deletions(-)
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
