The kernel needs to setup the first two tlbs with pad
which is used for early page allocation which is used
by mapin_ram() to allocate tables for lowmem memory
before memory initialisation is done.
Calculate pad directly from lowmem size.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current IFC driver supports till 4K page size NAND flash.
Add support of 8K Page size NAND flash
- Add nand_ecclayout for 4 bit & 8 bit ecc
- Defines constants
- also fix ecc.strength for 8bit ecc of 8K page size NAND
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here's the big drivers/staging/ update for 3.13-rc1.
Nothing major here, just a _ton_ of fixes and cleanups, mostly driven by
the new round of OPW applicants, but also there are lots of other people
doing staging tree cleanups these days in order to help get the drivers
into mergable shape.
We also merge, and then revert, the ktap code, as Ingo and the other
perf/ftrace developers feel it should go into the "real" part of the
kernel with only a bit more work, so no need to put it in staging for
now.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xPsACgkQMUfUDdst+ykAbwCg1hOktgHPFZp/t6xmsSj6cZHj
AfQAnRN/lr/TFw5SKUek2sluAzO4Fz7c
=g/MD
-----END PGP SIGNATURE-----
Merge tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver update from Greg KH:
"Here's the big drivers/staging/ update for 3.13-rc1.
Nothing major here, just a _ton_ of fixes and cleanups, mostly driven
by the new round of OPW applicants, but also there are lots of other
people doing staging tree cleanups these days in order to help get the
drivers into mergable shape.
We also merge, and then revert, the ktap code, as Ingo and the other
perf/ftrace developers feel it should go into the "real" part of the
kernel with only a bit more work, so no need to put it in staging for
now.
All of this has been in linux-next for a while with no reported
issues"
* tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1045 commits)
staging: drm/imx: fix return value check in ipu_add_subdevice_pdata()
Staging: zram: Fix access of NULL pointer
Staging: zram: Fix variable dereferenced before check
Staging: rtl8187se: space prohibited before semicolon in r8185b_init.c
Staging: rtl8187se: fix space prohibited after that open parenthesis '(' in r8185b_init.c
Staging: rtl8187se: fix braces {} are not necessary for single statement blocks in r8185b_init.c
Staging: rtl8187se: fix trailing whitespace in r8185b_init.c
Staging: rtl8187se: fix please, no space before tabs in r8185b_init.c
drivers/staging/nvec/Kconfig: remove trailing whitespace
Staging: dwc2: Fix variable dereferenced before check
Staging: xgifb: fix braces {} are not necessary for any arm of this statement
staging: rtl8192e: remove unneeded semicolons
staging: rtl8192e: use true and false for bool variables
staging: ft1000: return values corrected in scram_start_dwnld
staging: ft1000: change values of status return variable in write_dpram32_and_check
staging: bcm: Remove unnecessary pointer casting
imx-drm: ipuv3-crtc: Invert IPU DI0 clock polarity
staging: r8188eu: Fix sparse warnings in rtl_p2p.c
staging: r8188eu: Fix sparse warnings in rtw_mlme_ext.c
staging: r8188eu: Fix sparse warnings in rtl8188e.cmd.c
...
Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they all
get slowly migrated over to the safe versions of the attribute groups
(removing userspace races with the creation of the sysfs files.) Also
in here are some kobject updates, devres expansions, and the first round
of Tejun's sysfs reworking to enable it to be used by other subsystems
as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xAMACgkQMUfUDdst+yk1kQCfcHXhfnrvFZ5J/mDP509IzhNS
ddEAoLEWoivtBppNsgrWqXpD1vi4UMsE
=JmVW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they
all get slowly migrated over to the safe versions of the attribute
groups (removing userspace races with the creation of the sysfs
files.) Also in here are some kobject updates, devres expansions, and
the first round of Tejun's sysfs reworking to enable it to be used by
other subsystems as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
sysfs: rename sysfs_assoc_lock and explain what it's about
sysfs: use generic_file_llseek() for sysfs_file_operations
sysfs: return correct error code on unimplemented mmap()
mdio_bus: convert bus code to use dev_groups
device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
sysfs: separate out dup filename warning into a separate function
sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
sysfs: remove unused sysfs_get_dentry() prototype
sysfs: honor bin_attr.attr.ignore_lockdep
sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
devres: restore zeroing behavior of devres_alloc()
sysfs: fix sysfs_write_file for bin file
input: gameport: convert bus code to use dev_groups
input: serio: remove bus usage of dev_attrs
input: serio: use DEVICE_ATTR_RO()
i2o: convert bus code to use dev_groups
memstick: convert bus code to use dev_groups
tifm: convert bus code to use dev_groups
virtio: convert bus code to use dev_groups
ipack: convert bus code to use dev_groups
...
By default, IRQ work is run from the tick interrupt (see
irq_work_run() in update_process_times()). When we're in full
NOHZ mode, restarting the tick requires the use of IRQ work and
if the only place we run IRQ work is in the tick interrupt we
have an unbreakable cycle. Implement arch_irq_work_raise() via
self IPIs to break this cycle and get the tick started again.
Note that we implement this via IPIs which are only available on
SMP builds. This shouldn't be a problem because full NOHZ is only
supported on SMP builds anyway.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xycACgkQMUfUDdst+ymO+gCgxXdQXSU23i9ykc2CKBemdEBH
w6IAoKcokITcdN1IxxkfiMxOEld2hgZm
=3kbb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver update from Greg KH:
"Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported
issues"
* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
USB: Maintainers change for usb serial drivers
usb: usbtest: support container id descriptor test
usb: usbtest: support superspeed device capbility descriptor test
usb: usbtest: support usb2 extension descriptor test
usb: chipidea: only get vbus regulator for non-peripheral mode
USB: ehci-atmel: add usb_clk for transition to CCF
usb: cdc-wdm: ignore speed change notifications
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
usb: usbtest: support bos descriptor test for usb 3.0
USB: phy: samsung: Support multiple PHYs of same type
usb: wusbcore: change WA_SEGS_MAX to a legal value
usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
usb: wusbcore: combine multiple isoc frames in a single transfer request.
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
usb: chipidea: host: more enhancement when ci->hcd is NULL
usb: ohci: remove ep93xx bus glue platform driver
usb: usbtest: fix checkpatch warning as sizeof code style
UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
...
The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified. On the
Qualcomm Snapdragon S4/Krait architecture CPUs the processor continues
to consider the IT state bits while in ARM mode. This makes it so
that some instructions are skipped by the CPU.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[rmk+kernel@arm.linux.org.uk: fixed whitespace formatting in patch]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No-MMU configurations currenty fail to build because they are missing
the early_paging_init() symbol.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The exception handling code fails to clear the IT state, potentially
leading to incorrect execution of the fixup if the size of the IT
block is more than one.
Let fixup_exception do the IT sanitizing if a fixup has been found,
and restore CPSR from the stack when returning from a data abort.
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 6dedcca610 ("hotplug, powerpc, x86: Remove
cpu_hotplug_driver_lock())" removes the the definition of
cpu_hotplug_driver_{lock,unlock} APIs, thereby causing a build error.
Replace these calls with {lock,unlock}_device_hotplug().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Certain platforms do not allow writes in the MSI-X BARs to setup or tear
down vector values. To combat against the generic code trying to write to
that and either silently being ignored or crashing due to the pagetables
being marked R/O this patch introduces a platform override.
Note that we keep two separate, non-weak, functions default_mask_msi_irqs()
and default_mask_msix_irqs() for the behavior of the arch_mask_msi_irqs()
and arch_mask_msix_irqs(), as the default behavior is needed by x86 PCI
code.
For Xen, which does not allow the guest to write to MSI-X tables - as the
hypervisor is solely responsible for setting the vector values - we
implement two nops.
This fixes a Xen guest crash when passing a PCI device with MSI-X to the
guest. See the bugzilla for more details.
[bhelgaas: add bugzilla info]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=64581
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
CC: Zhenzhong Duan <zhenzhong.duan@oracle.com>
The early_init_devtree() API was removed in linux-next for 3.13 with
commit "mips: use early_init_dt_scan". This causes Netlogic XLP compile
to fail:
arch/mips/netlogic/xlp/setup.c:101: undefined reference to `early_init_devtree'
Add xlp_early_init_devtree() which uses the __dt_setup_arch() to
handle early device tree related initialization to fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch proposes to remove the IRQF_DISABLED flag from x86/xen
code. It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Currently xol_get_insn_slot() assumes that we should simply copy
arch_uprobe->insn[] which is (ignoring arch_uprobe_analyze_insn)
just the copy of the original insn.
This is not true for arm which needs to create another insn to
execute it out-of-line.
So this patch simply adds the new member, ->ixol into the union.
This doesn't make any difference for x86 and powerpc, but arm
can divorce insn/ixol and initialize the correct xol insn in
arch_uprobe_analyze_insn().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Move the function declarations from the arch headers to the common
header, since only the function bodies are architecture-specific.
These changes are from Vincent Rabin's uprobes patch.
[ oleg: update arch/powerpc/include/asm/uprobes.h ]
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
The variable hv_lapic_frequency causes an unused variable warning if
CONFIG_X86_LOCAL_APIC is disabled. Since the variable is only used
inside a small if statement, move the declaration of that variable
into the if statement itself.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Link: http://lkml.kernel.org/r/1381444224-3303-1-git-send-email-kys@microsoft.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently seqlocks and seqcounts don't support lockdep.
After running across a seqcount related deadlock in the timekeeping
code, I used a less-refined and more focused variant of this patch
to narrow down the cause of the issue.
This is a first-pass attempt to properly enable lockdep functionality
on seqlocks and seqcounts.
Since seqcounts are used in the vdso gettimeofday code, I've provided
non-lockdep accessors for those needs.
I've also handled one case where there were nested seqlock writers
and there may be more edge cases.
Comments and feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Unlike other uncore boxes, IRP boxes live in PCI buses with no UBOX
device. For PCI bus without UBOX device, we find the next bus that
has UBOX device and use its 'bus to socket' mapping.
Besides the counter/control registers in IRP boxes are not properly
aligned.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: eranian@google.com
Cc: "Yan Zheng" <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1383197815-17706-2-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The encoding for filter registers of IvyBridge-EP uncore QPI boxes is
completely the same as SandyBridge-EP.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: eranian@google.com
Cc: "Yan Zheng" <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1383197815-17706-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The arch_perf_output_copy_user() default of
__copy_from_user_inatomic() returns bytes not copied, while all other
argument functions given DEFINE_OUTPUT_COPY() return bytes copied.
Since copy_from_user_nmi() is the odd duck out by returning bytes
copied where all other *copy_{to,from}* functions return bytes not
copied, change it over and ammend DEFINE_OUTPUT_COPY() to expect bytes
not copied.
Oddly enough DEFINE_OUTPUT_COPY() already returned bytes not copied
while expecting its worker functions to return bytes copied.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: will.deacon@arm.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20131030201622.GR16117@laptop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kick interrupts trigger the LWK (low level kick) signal, usually handled
by the __TBIDoStdLWK() function which is the only handler inherited from
the bootloader. The LWK signal is converted either to a SWK (plain
software kick) or a SWS (software kick with an attached message).
Linux has kick_handler() to handle SWK and call registered kick handlers
(IPIs and inter-thread comms), but SWS is as far as I'm aware unused
with Linux.
Therefore remove that abstraction and have Linux handle LWK directly.
This will reduce kick latency slightly, and reduce our dependence on the
bootloader, which makes it easier to directly boot a kernel in QEMU
(particularly for SMP).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Ensure that accesses to the GICH_* registers are byteswapped
when the kernel is compiled as big-endian.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Force SCTLR_EL2.EE to 1 if the kernel is compiled as BE.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The prototype for kvm_check_iopl appeared in commit
f850e2e603 ("KVM: x86 emulator: Check IOPL
level during io instruction emulation"), but the function never actually
existed. Remove the prototype.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
complete_pio ceased to exist in commit
7972995b0c ("KVM: x86 emulator: Move
string pio emulation into emulator.c"), but the prototype remained.
Remove its prototype.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
In certain occasions it is possible for a hung task detector
positive to be false: continuation from a paused VM, for example.
Add a method to reset detection, similar as is done
with other kernel watchdogs.
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This removes the NO_MMU Kconfig parameter,
which was no longer used anywhere in the source code
and Makefiles.
This also updates a comment refering to this parameter.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement reset of kernel watchdogs at pvclock read time. This avoids
adding special code to every watchdog.
This is possible for watchdogs which measure time based on sched_clock() or
ktime_get() variants.
Suggested by Don Zickus.
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
I noticed that srcu_read_lock/unlock both have a memory barrier,
so just by moving srcu_read_unlock earlier we can get rid of
one call to smp_mb() using smp_mb__after_srcu_read_unlock instead.
Unsurprisingly, the gain is small but measureable using the unit test
microbenchmark:
before
vmcall in the ballpark of 1410 cycles
after
vmcall in the ballpark of 1360 cycles
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The MAXSMP option is intended to enable silly large numbers of
CPUs for testing purposes. The current value of 4096 isn't very
silly any longer as there are actual SGI machines that approach
6096 CPUs when taking HT into account.
Increase the value to a nice round 8192 to account for this and
allow for short term future increases.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: prarit@redhat.com
Cc: Russ Anderson <rja@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131105143816.GK9944@hansolo.jdub.homelinux.org
[ Tweaked it so that MAXSMP simply sets the maximum of the normal range. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current range for SMP configs is 2 - 512 CPUs, or a full
4096 in the case of MAXSMP. There are machines that have 1024
CPUs in them today and configuring a kernel for that means you
are forced to set MAXSMP. This adds additional unnecessary
overhead. While that overhead might be considered tiny for
large machines, it isn't necessarily so if you are building a
kernel that runs across a wide variety of machines.
To cover the range of more common machines today, we allow
NR_CPUS to be up to 4096 when CPUMASK_OFFSTACK is enabled.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: prarit@redhat.com
Cc: Russ Anderson <rja@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131105143728.GJ9944@hansolo.jdub.homelinux.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently show_cpuinfo_core() displays cpu core information only if
the number of threads per a whole cores is 2 or larger.
However, this condition doesn't care about the number of
sockets. For example, this condition doesn't hold on systems
with two logical cpus consisting of two sockets and a single
core on each socket - yet the topology information would be
interesting to see in that case as well.
I don't know whether or not there are processors in real world
by which such configurations are possible, but at least on
vitual machine environments, such configuration can occur,
typically when no explicit SMP information is provided in
advance.
For example, on qemu/KVM, SMP information is specified via -smp
command-line option, more specifically, its syntax is:
-smp n[,cores=cores][,threads=threads][,sockets=sockets][,maxcpus=maxcpus]
If this is not specified, qemu tells configuration with
n-sockets, 1-core and 1-thread to the guest machine, on which
guest, MP information is not displayed in /proc/cpuinfo.
I saw this situation on VMWare guest environment, too.
To fix this issue, this patch simply removes the condition
because this information is useful even if there's only 1
thread.
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/5277D644.4090707@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
kernel/Makefile
There are conflicts in kernel/Makefile due to file moving in the
scheduler tree - resolve them.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSdt9HAAoJEHm+PkMAQRiGnzEH/345Keg5dp+oKACnokBfzOtp
V0p3g5EBsGtzEVnV+1B96trczDUtWdDFFr5GfGSj565NBQpFyc+iZC1mC99RDJCs
WUquGFqlLMK2aV0SbKwCO4K1rJ5A0TRVj0ZRJOUJUY7jwNf5Qahny0WBVjO/8qAY
UvJK1rktBClhKdH53YtpDHHgXBeZ2LOrzt1fQ/AMpujGbZauGvnLdNOli5r2kCFK
jzoOgFLvX+PHU/5/d4/QyJPeQNPva5hjk5Ho9UuSJYhnFtPO3EkD4XZLcpcbNEJb
LqBvbnZWm6CS435lfU1l93RqQa5xMO9ITk0oe4h69syTSHwWk9aJ+ZTc/4Up+t8=
=57MC
-----END PGP SIGNATURE-----
Merge tag 'v3.12' into x86/cpu, to refresh the branch before queueing up more changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ST.as only takes S9 (255) for offset. This was going out of range when
accessing a task_struct field with 4k NR_CPUS (due to 128b of coumaks
itself in there).
Workaround by using an intermediate register to do the address scaling.
There is some duplication of fix for ctx_sw.c and ctx_sw_asm.S however
given that C version will go away soon I'm not bothering to factor out
the common code.
Reported-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Add mm_cpumask setting (aggregating only, unlike some other arches)
used to restrict the TLB flush cross-calling
- cross-calling versions of TLB flush routines (thanks to Noam)
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Need export symbol for it, or can not pass compiling, the related error
with allmodconfig:
MODPOST 2994 modules
ERROR: "pm_power_off" [drivers/mfd/retu-mfd.ko] undefined!
ERROR: "pm_power_off" [drivers/char/ipmi/ipmi_poweroff.ko] undefined!
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Need export its symbol just like other architectures done, or can not
pass compiling with allmodconfig, the related error:
MODPOST 2994 modules
ERROR: "save_stack_trace" [kernel/backtracetest.ko] undefined!
ERROR: "save_stack_trace" [drivers/md/persistent-data/dm-persistent-data.ko] undefined!
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
get_hw_config_num_irq() may be called by normal iss_model_init_smp()
which is a function pointer for 'init_smp' which may be called by
first_lines_of_secondary() which also need be normal too.
The related warning (with allmodconfig):
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x5814): Section mismatch in reference from the function iss_model_init_smp() to the function .init.text:get_hw_config_num_irq()
The function iss_model_init_smp() references
the function __init get_hw_config_num_irq().
This is often because iss_model_init_smp lacks a __init
annotation or the annotation of get_hw_config_num_irq is wrong.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
first_lines_of_secondary() is a '__init' function, but it may be called
by __cpu_up() by _cpu_up() by cpu_up() which is a normal export symbol
function. So recommend to remove '__init'.
The related warning (with allmodconfig):
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x315c): Section mismatch in reference from the function __cpu_up() to the function .init.text:first_lines_of_secondary()
The function __cpu_up() references
the function __init first_lines_of_secondary().
This is often because __cpu_up lacks a __init
annotation or the annotation of first_lines_of_secondary is wrong.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
They haven't '__init' in definition, but has '__init' in declaration.
And normal function start_kernel_secondary() may call setup_processor()
which will call arc_init_IRQ().
So need remove '__init' for both of them. The related warning (with
allmodconfig):
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x3084): Section mismatch in reference from the function start_kernel_secondary() to the function .init.text:setup_processor()
The function start_kernel_secondary() references
the function __init setup_processor().
This is often because start_kernel_secondary lacks a __init
annotation or the annotation of setup_processor is wrong.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
arc supports kgdb, but need update -- add function kgdb_roundup_cpus(),
or can not pass compiling. At present, add the simple generic one just
like other architectures(e.g. tile, mips ...).
The related error (with allmodconfig):
kernel/built-in.o: In function `kgdb_cpu_enter':
kernel/debug/debug_core.c:580: undefined reference to `kgdb_roundup_cpus'
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
------------------>8----------------------
arch/arc/mm/tlb.c: In function ‘do_tlb_overlap_fault’:
arch/arc/mm/tlb.c:688:13: warning: array subscript is above array bounds
[-Warray-bounds]
(pd0[n] & PAGE_MASK)) {
^
------------------>8----------------------
While at it, remove the usless last iteration of outer loop when reading
a TLB SET for duplicate entries.
Suggested-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Lockdep required a small fix to stacktrace API which was incorrectly
unwindign out of __switch_to for the current call frame.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In case bootloader has changed the priority of one/more IRQ lines
Reported-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
switch the args (address, pt_regs) to match with all the other "C"
exception handlers.
This removes the awkwardness in EV_ProtV for page fault vs. unaligned
access.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Line op needs vaddr (indexing) and paddr (tag match). For page sized
flushes (V-P const), each line op will need a different index, but the
tag bits wil remain constant, hence paddr can be setup once outside the
loop.
This improves select LMBench numbers for Aliasing dcache where we have
more "preventive" cache flushing.
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.11-rc7- Linux 3.11.0- 80 4.66 8.88 69.7 112. 268. 8.60 28.0 3489 13.K 27.K # Non alias ARC700
3.11-rc7- Linux 3.11.0- 80 4.64 8.51 68.6 98.5 271. 8.58 28.1 4160 15.K 32.K # Aliasing
3.11-rc7- Linux 3.11.0- 80 4.64 8.51 69.8 99.4 270. 8.73 27.5 3880 15.K 31.K # PTAG loop Inv
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With Line length being constant now, we can fold the 2 helpers into 1.
This allows applying any optimizations (forthcoming) to single place.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC dcache supports 3 ops - Inv, Flush, Flush-n-Inv.
The programming model however provides 2 commands FLUSH, INV.
INV will either discard or flush-n-discard (based on DT_CTRL bit)
The leaf helper __dc_line_loop() used to take the AUX register
(corresponding to the 2 commands). Now we push that to within the
helper, paving way for code consolidations to follow.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of them is
address calculation via the form &__get_cpu_var(x). This calculates the address for
the instance of the percpu variable of the current processor based on an offset.
Other use cases are for storing and retrieving data from the current processors percpu area.
__get_cpu_var() can be used as an lvalue when writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store and retrieve operations
could use a segment prefix (or global register on other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a percpu area and use
optimized assembly code to read and write per cpu variables.
This patch converts __get_cpu_var into either an explicit address calculation using this_cpu_ptr()
or into a use of this_cpu operations that use the offset. Thereby address calcualtions are avoided
and less registers are used when code is generated.
At the end of the patchset all uses of __get_cpu_var have been removed so the macro is removed too.
The patchset includes passes over all arches as well. Once these operations are used throughout then
specialized macros can be defined in non -x86 arches as well in order to optimize per cpu access by
f.e. using a global register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu variable.
DEFINE_PER_CPU(int, u);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(this_cpu_ptr(&x), y, sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
this_cpu_inc(y)
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
When restoring the PPR value, we incorrectly access the thread structure
at a time where MSR:RI is clear, which means we cannot recover from nested
faults. However the thread structure isn't covered by the "bolted" SLB
entries and thus accessing can fault.
This fixes it by splitting the code so that the PPR value is loaded into
a GPR before MSR:RI is cleared.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We're assigning PE numbers after the completion of PCI probe. During
the PCI probe, we had PE#0 as the super container to encompass all
PCI devices. However, that's inappropriate since PELTM has ascending
order of priority on search on P7IOC. So we need PE#127 takes the
role that PE#0 has previously. For PHB3, we still have PE#0 as the
reserved PE.
The patch supposes that the underly firmware has built the RID to
PE# mapping after resetting IODA tables: all PELTM entries except
last one has invalid mapping on P7IOC, but all RTEs have binding
to PE#0. The reserved PE# is being exported by firmware by device
tree.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need add PE to its own PELTV. Otherwise, the errors originated
from the PE might contribute to other PEs. In the result, we can't
clear up the error successfully even we're checking and clearing
errors during access to PCI config space.
Cc: stable@vger.kernel.org
Reported-by: kalshett@in.ibm.com
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Indirect XSCOM addresses normally have the top bit set (of the 64-bit
address). This doesn't work via the normal debugfs interface, so we use
a different encoding, which we need to convert before calling OPAL.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current debugfs interface to scom is essentially unused
and racy. It uses two different files "address" and "data"
to perform accesses which is at best impractical for anything
but manual use by a developer.
This replaces it with an "access" file which represent the entire
scom address space which can be lseek/read/writen too.
This file only supports accesses that are 8 bytes aligned and
multiple of 8 bytes in size. The offset is logically the SCOM
address multiplied by 8.
Since nothing in userspace exploits that file at the moment, the ABI
change is a no-brainer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On P8, XSCOM addresses has a special "indirect" form that
requires more than 32-bits, so let's use u64 everywhere in
the code instead of u32.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified. If an ARM
function is registered as a signal handler, and that signal is delivered
inside a block of instructions following an IT instruction, some of the
instructions at the beginning of the signal handler may be skipped if
the IT state bits of the Program Status Register are not cleared by the
kernel.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[catalin.marinas@arm.com: code comment and commit log updated]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch expands the VA_BITS to 42 when the 64K page configuration is
enabled allowing 2TB kernel linear mapping. Linux still uses 2 levels of
page tables in this configuration with pgd now being a full page.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
arch/openrisc/kernel/module.c: In function 'apply_relocate_add':
arch/openrisc/kernel/module.c:50:13: warning: assignment from incompatible pointer type
arch/openrisc/kernel/module.c:54:13: warning: assignment from incompatible pointer type
Move the pointer increments to the dereference statements to avoid
incompatible pointer assignments, and remove superfluous casts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Add default "vga.h", or compiling fails with 'allmodconfig'.
The related error:
CC [M] drivers/gpu/drm/drm_irq.o
In file included from include/linux/vgaarb.h:34:0,
from drivers/gpu/drm/drm_irq.c:42:
include/video/vga.h:22:21: fatal error: asm/vga.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/gpu/drm/drm_irq.o] Error 1
make[2]: *** [drivers/gpu/drm] Error 2
make[1]: *** [drivers/gpu] Error 2
make: *** [drivers] Error 2
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Need append "_D__linux__" to KBUILD_CFLAGS, just like some of another
architectures have done, or 'allmodconfig' can not pass compiling.
The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:65:0,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221:2: error: expected specifier-qualifier-list before 'u_quad_t'
The related compiler information:
[root@dhcp122 ~]# /usr/local/bin/or32-linux-gcc -v
Using built-in specs.
COLLECT_GCC=/usr/local/bin/or32-linux-gcc
COLLECT_LTO_WRAPPER=/usr/local/libexec/gcc/or32-linux/4.5.1-or32-1.0rc1/lto-wrapper
Target: or32-linux
Configured with: ../gcc-openrisc/configure --target=or32-linux --disable-nls --enable-languages=c --without-headers --disable-shared --disable-threads --enable-werror=no
Thread model: single
gcc version 4.5.1-or32-1.0rc1 (GCC)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Relocations that require an instruction immediate to be re-encoded must
ensure that the instruction pattern is represented in a little-endian
format for the manipulation code to work correctly.
This patch converts the loaded instruction into native-endianess prior
to encoding and then converts back to little-endian byteorder before
updating memory.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tested-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
preempt_count is defined as an int. Oddly enough, we access it
as a 64bit value. Things become interesting when running a BE
kernel, and looking at the current CPU number, which is stored
as an int next to preempt_count. Like in a per-cpu interrupt
handler, for example...
Using a 32bit access fixes the issue for good.
Cc: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently cpuid emulation is traced only when executed by intercept.
Move trace point so that emulator invocation is traced too.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
All decode_register() callers check if instruction has rex prefix
to properly decode one byte operand. It make sense to move the check
inside.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The defconfig kernel can not run under neither fedora16 x86_64 laptop
nor fedora17 x86_64 pc. After enable DEVTMPFS* in x86_64_defconfig, it
will be OK.
DEVTMPFS* is only related with software, so for i386_defconfig may also
need them (at least, it has no negative effect for defconfig).
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Link: http://lkml.kernel.org/r/52784DFF.8040004@asianux.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fix f0308261b1 ("powerpc/pci: Use pci_is_pcie() to simplify code"). I
accidentally merged v2 instead of v3, so this adds the difference. Without
this, "cap" is the left-over PCI-X capability offset, and we're using it as
the PCIe capability offset.
[bhelgaas: extracted v2->v3 diff]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The wrapper script needs an explicit rule for the "of" boot
wrapper (generic wrapper, similar to pseries). Before
0c9fa29149 it was hanlded
implicitly by the statement:
platformo=$object/"$platform".o
But now that epapr.o needs to be added, that doesn't work
and an explicit rule must be added.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 53ae3acd (arm64: Only enable local interrupts after the CPU
is marked online) moved the enabling of the GIC after the CPUs are
marked online.
This has some interesting effect:
[...]
[<ffffffc0002eefd8>] gic_raise_softirq+0xf8/0x160
[<ffffffc000088f58>] smp_send_reschedule+0x38/0x40
[<ffffffc0000c8728>] resched_task+0x84/0xc0
[<ffffffc0000c8cdc>] check_preempt_curr+0x58/0x98
[<ffffffc0000c8d38>] ttwu_do_wakeup+0x1c/0xf4
[<ffffffc0000c8f90>] ttwu_do_activate.constprop.84+0x64/0x70
[<ffffffc0000cad30>] try_to_wake_up+0x1d4/0x2b4
[<ffffffc0000cae6c>] default_wake_function+0x10/0x18
[<ffffffc0000c5ca4>] __wake_up_common+0x60/0xa0
[<ffffffc0000c7784>] complete+0x48/0x64
[<ffffffc000088bec>] secondary_start_kernel+0xe8/0x110
[...]
Here, we end-up calling gic_raise_softirq without having initialized
the interrupt controller for this CPU. While this goes unnoticed
with GICv2 (the distributor is always accessible), it explodes with
GICv3.
The fix is to move the call to notify_cpu_starting before we set
the secondary CPU online.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The .data section in the arm64 linker script currently lacks a
definition for page-aligned data. This leads to a .page_aligned
section being placed between the end of data and start of bss.
This patch corrects that by using the generic RW_DATA_SECTION
macro which includes support for page-aligned data.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Another whitespace clean-up, this removes tabs from between sentences in
some comments.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The IDTE instruction used to flush TLB entries for a specific address
space uses the address-space-control element (ASCE) to identify
affected TLB entries. The upgrade of a page table adds a new top
level page table which changes the ASCE. The TLB entries associated
with the old ASCE need to be flushed and the ASCE for the address space
needs to be replaced synchronously on all CPUs which currently use it.
The concept of a lazy ASCE update with an exception handler is broken.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes for build issues when LPB FIFO driver is configured as
a module, removal of #ifdefs in mpc512x DIU platform code and
a revert of recent changes to mpc52xx PIC driver. Wolfram
provided a better fix for PIC driver build issue popping up
when older gcc-4.3.5 is used.
Commit 2361613206, "of/irq: Refactor interrupt-map parsing" introduced
a bug. The irq parsing will fail for some nodes that don't have a reg
property. It is fixed by deferring the check for reg until it is
actually needed. Also adjust the testcase data to catch the bug.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Pull MIPS fixes from Ralf Baechle:
"Three fixes across arch/mips with the most complex one being the GIC
interrupt fix - at nine lines still not monster. I'm confident this
are the final MIPS patches even if there should go for an rc8"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: fix return value check in rt_timer_probe()
MIPS: malta: Fix GIC interrupt offsets
MIPS: Perf: Fix 74K cache map
When I was looking at RHEL5.9's failure to start with
unrestricted_guest=0/emulate_invalid_guest_state=1, I got it working with a
slightly older tree than kvm.git. I now debugged the remaining failure,
which was introduced by commit 660696d1 (KVM: X86 emulator: fix
source operand decoding for 8bit mov[zs]x instructions, 2013-04-24)
introduced a similar mis-emulation to the one in commit 8acb4207 (KVM:
fix sil/dil/bpl/spl in the mod/rm fields, 2013-05-30). The incorrect
decoding occurs in 8-bit movzx/movsx instructions whose 8-bit operand
is sil/dil/bpl/spl.
Needless to say, "movzbl %bpl, %eax" does occur in RHEL5.9's decompression
prolog, just a handful of instructions before finally giving control to
the decompressed vmlinux and getting out of the invalid guest state.
Because OpMem8 bypasses decode_modrm, the same handling of the REX prefix
must be applied to OpMem8.
Reported-by: Michele Baldessari <michele@redhat.com>
Cc: stable@vger.kernel.org
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
A vmalloc fault needs to sync up PGD/PTE entry from init_mm to current
task's "active_mm". ARC vmalloc fault handler however was using mm.
A vmalloc fault for non user task context (actually pre-userland, from
init thread's open for /dev/console) caused the handler to deref NULL mm
(for mm->pgd)
The reasons it worked so far is amazing:
1. By default (!SMP), vmalloc fault handler uses a cached value of PGD.
In SMP that MMU register is repurposed hence need for mm pointer deref.
2. In pre-3.12 SMP kernel, the problem triggering vmalloc didn't exist in
pre-userland code path - it was introduced with commit 20bafb3d23
"n_tty: Move buffers into n_tty_data"
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: stable@vger.kernel.org #3.10 and 3.11
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf fixes from Ingo Molnar:
"Two fixes:
- Fix 'NMI handler took too long to run' false positives
[ Genuine NMI overhead speedups will come for v3.13, this commit
only fixes a measurement bug ]
- Fix perf ring-buffer missed barrier causing (rare) ring-buffer data
corruption on ppc64"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix NMI measurements
perf: Fix perf ring buffer memory ordering
Resolve cherry-picking conflicts:
Conflicts:
mm/huge_memory.c
mm/memory.c
mm/mprotect.c
See this upstream merge commit for more details:
52469b4fcd Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Yet another instruction that we fail to emulate, this time found
in Windows 2008R2 32-bit.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* pci/yijing-mps-v1:
drm/radeon: use pcie_get_readrq() and pcie_set_readrq() to simplify code
staging: et131x: Use pci_dev->pcie_mpss and pcie_set_readrq() to simplify code
IB/qib: Drop qib_tune_pcie_caps() and qib_tune_pcie_coalesce() return values
IB/qib: Use pcie_set_mps() and pcie_get_mps() to simplify code
IB/qib: Use pci_is_root_bus() to check whether it is a root bus
tile/PCI: use cached pci_dev->pcie_mpss to simplify code
PCI: Export pcie_set_mps() and pcie_get_mps()
A handful of DT updates from Christian Daudt for the broadcom mobile
platforms, including their rename of the platform to BCM_MOBILE to keep
BCM for the vendor-level options.
* bcm/dt:
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
Signed-off-by: Olof Johansson <olof@lixom.net>
Trivial patch to make use of GIC/IRQ defines on the bcm11351 sdio
interrupt properties.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds in three more UARTs that were not declared earlier.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Register GPIO 14 as card detect interrupt for the SD card slot.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the GPIO controller device node for the Broadcom bcm281xx family of
mobile SoCs.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit e8765b265a (arm64: read enable-method for CPU0) introduced
checks for the enable method on CPU0 (to be later used with CPU
suspend). However, if the kernel is compiled for UP and a DT file is
used with a method like 'spin-table', Linux complains about 'invalid
enable method'. This patch turns it into an 'unsupported enable method'
warning.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is a possible race between setting has_pgste and reallocation of the
page_table, change the order to fix this.
Also page_table_alloc_pgste can fail, in that case we need to backpropagte this
as -ENOMEM to the caller of page_table_realloc.
Based on a patch by Christian Borntraeger <borntraeger@de.ibm.com>.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:
- Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
to be splitted for submission of RTC part first;
- Front LCD (Winstar 1602G): driver needs to be written
- Armada NAND controller (to access onboard 128MB of NAND): support
being pushed by @free-electrons people
- 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
driver is available upstream. Not referenced/tested yet.
but the device is usable w/o those.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most of the kernel code assumes that max*pfn is maximum pfns because
the physical start of memory is expected to be PFN0. Since this
assumption is not true on ARM architectures, the meaning of max*pfn
is number of memory pages. This is done to keep drivers happy which
are making use of of these variable to calculate the dma bounce limit
using dma_mask.
Now since we have a architecture override possibility for DMAable
maximum pfns, lets make meaning of max*pfns as maximum pnfs on ARM
as well.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to start treating DMA masks as something which is specific to
the bus that the device resides on, otherwise we're going to hit all
sorts of nasty issues with LPAE and 32-bit DMA controllers in >32-bit
systems, where memory is offset from PFN 0.
In order to start doing this, we convert the DMA mask to a PFN using
the device specific dma_to_pfn() macro. This is the reverse of the
pfn_to_dma() macro which is used to get the DMA address for the device.
This gives us a PFN mask, which we can then check against the PFN
limit of the DMA zone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an asmlinkage wrapper around acpi_enter_sleep_state() to prevent
an empty stub from being called by assmebly code for ACPI_REDUCED_HARDWARE
set.
As arch/x86/kernel/acpi/wakeup_xx.S is only compiled when CONFIG_ACPI=y
and there are no users of ACPI_HARDWARE_REDUCED, currently this is in
fact not a real issue, but a cleanup to reduce source code differences
between Linux and ACPICA upstream.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In case of error, the function devm_request_and_ioremap() returns NULL
pointer not ERR_PTR(). Fix it by using devm_ioremap_resource() instead
of devm_request_and_ioremap().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: grant.likely@linaro.org
Cc: rob.herring@calxeda.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6098/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mst can't be blamed for lack of switch entries: the
issue is with msrs actually.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
arch/arm/mach-footbridge/netwinder-hw.c:695:2: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
arch/arm/mach-footbridge/netwinder-hw.c:702:2: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
arch/arm/mach-footbridge/netwinder-hw.c:712:2: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
arch/arm/mach-footbridge/netwinder-hw.c:714:2: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The loop was always using 0 as the index. This means that
any rubbish after the first element of the array went undetected.
It seems reasonable to assume that no KVM userspace did that.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM_SET_XCRS ioctl must accept anything that KVM_GET_XCRS
could return. XCR0's bit 0 is always 1 in real processors with
XSAVE, and KVM_GET_XCRS will always leave bit 0 set even if the
emulated processor does not have XSAVE. So, KVM_SET_XCRS must
ignore that bit when checking for attempts to enable unsupported
save states.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new Kconfig choice group which allows to configure how gcc should
tune the generated code (via -mtune option).
By default the -mtune parameter will match the -march parameter.
This is a rather large patch, but I wouldn't know how to make this shorter
unfortunately.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
this_cpu_xor() will be removed tree wide during the next merge window.
To avoid merge conflicts s390's removal comes via the s390 tree.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the ACCESS_ONCE macro for both accesses to idle->sequence in the
loops to calculate the idle time. If only one access uses the macro,
the compiler is free to cache the value for the second access which
can cause endless loops.
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The get_tod_clock_ext inline assembly does not specify its output
operands correctly. This can cause incorrect code to be generated.
Cc: stable@vger.kernel.org # 3.12
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit b6069a9570 (filter: add MOD operation) added generic
support for modulus operation in BPF.
This patch brings JIT support for PPC64
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently DIVWU stands for *signed* divw opcode:
7d 2a 4b 96 divwu r9,r10,r9
7d 2a 4b d6 divw r9,r10,r9
Use the *unsigned* divw opcode for DIVWU.
Suggested-by: Vassili Karpov <av1474@comtv.ru>
Reviewed-by: Vassili Karpov <av1474@comtv.ru>
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the definition of_find_next_cache_node is architecture independent,
the existing definition in powerpc can be moved to driver/of/base.c
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently big endianness of the device tree data is assumed in
of_find_next_cache_node for 'handle' when calling of_find_node_by_phandle.
In preparation to move this function to common code, this patch fixes
the endianness using 'be32_to_cpup'
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently turn IRQs off in __switch_to(0 but this is unnecessary as it's
already disabled in the caller.
This removes the IRQ disable but adds a check to make sure it is really off
in case this changes in future.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is an optimization for the PowerPC in 64-bit
little-endian. Bit counting is used in find_zero(), instead
of the multiply and shift.
It is modelled after Alan Modra's PowerPC LE strlen patch
http://sourceware.org/ml/libc-alpha/2013-08/msg00097.html.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This enables the Berkeley Packet Filter JIT compiler
for the PowerPC running in 64bit Little Endian.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when not in hypervisor mode the kernel
Oopses during suspend or hibernation when accessing
the SDR1 register, because it is only available
in hypervisor mode. Access to it needs to be
protected in BEGIN/END_FW_FTR_SECTION.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Jimmy Pan <jipan@redhat.com>
Tested-by: Jimmy Pan <jipan@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When reading partitions, the length has to be translated from
big endian to the endian order of the host. Similarly, when writing
partitions, the length needs to be in big endian order.
The userspace tool 'nvram' needs a similar fix as it is reading
and writing partitions through /dev/nram :
http://sourceforge.net/p/powerpc-utils/mailman/message/31571277/
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
nvram_scan_partitions() is called twice when initializing the "lnx,oops-log"
partition and the "ibm,rtas-log" partition. This fills the partition list
with duplicate entries. This patch moves the partition scan in the init
routine pseries_nvram_init_log_partitions() which is called only once.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch (re)adds ARCH_BCM_MOBILE option to bcm_defconfig which was
accidentally removed by commit 2d58b26550 ('ARM: bcm_defconfig: Run
"make savedefconfig"')
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The IOMMU node's reg property contains completely bogus values! Somehow,
this had no practical effect, despite the fact the IOMMU driver appears
to be writing to those registers. I suppose that since no HW modules is
actually at that address, the writes simply had no effect.
Note that I'm not CCing stable here, even though the problem exists as
far back as v3.9, simply because this patch doesn't fix any observed
issue, and I don't want to run the risk of suddenly writing to some
registers and causing a regression.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, wrote commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
9e7827b5ea ("x86, hyperv: Get the local APIC timer frequency from the
hypervisor") breaks the build with some configs because apic.h isn't
directly included:
arch/x86/kernel/cpu/mshyperv.c: In function 'ms_hyperv_init_platform':
arch/x86/kernel/cpu/mshyperv.c:90:3: error: 'lapic_timer_frequency' undeclared (first use in this function)
arch/x86/kernel/cpu/mshyperv.c:90:3: note: each undeclared identifier is reported only once for each function it appears in
Fix it by including asm/apic.h.
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1310111604160.31170@chino.kir.corp.google.com
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Conflicts:
arch/arm/kernel/head.S
This series has been well tested and it would be great to get this
merged now.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU_DYING notifier is called by cpu stopper task which
does not own the context held in the VFP hardware. Calling
vfp_force_reload() has no effect.
Replace it with clearing vfp_current_hw_state.
Signed-off-by: Yuanyuan Zhong <zyy@motorola.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When platform_driver_probe() is not used, bind/unbind via sysfs is
enabled. Thus, __init annotation should be removed from probe().
Also, this patch fixes section mismatch warning.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change raw printk() call to dev_err() to provide a better message
to userspace so it can properly identify the device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Several functions are only ever referenced locally, so make them static.
Of those functions, many of them are protected by an #if. However, the
code which can compile fine in either case.
Now that (1) the unneeded code is marked 'static' and (2) the code is
only used under a C 'if (IS_ENABLED(CONFIG_FB_FSL_DIU))', the compiler
can automatically remove the unneeded code, and we don't need the #if or
the empty stub functions.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The MPC5200 LPBFIFO driver requires the bestcomm module to be
enabled, otherwise building will fail. Fix it.
Cc: <stable@vger.kernel.org> # 3.10+
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This more or less reverts commit 6391f697d4.
Instead of adding an unneeded 'default', mark the variable to prevent
the false positive 'uninitialized var'. The other change (fixing the
printout) needs revert, too. We want to know WHICH critical irq failed,
not which level it had.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
a disabled Kconfig option results in a reference to a not implemented
routine when the IS_ENABLED() macro is used for both conditional
implementation of the routine as well as a C language source code test
at the call site -- the "if (0) func();" construct only gets eliminated
later by the optimizer, while the compiler already has emitted its
warning about "func()" being undeclared
provide an empty implementation for the mpc512x_setup_diu() and
mpc512x_init_diu() routines in case of the disabled option, to avoid the
compiler warning which is considered fatal and breaks compilation
the bug appeared with commit 2abbbb63c9
"powerpc/mpc512x: move common code to shared.c file", how to reproduce:
make mpc512x_defconfig
echo CONFIG_FB_FSL_DIU=n >> .config && make olddefconfig
make
CC arch/powerpc/platforms/512x/mpc512x_shared.o
.../arch/powerpc/platforms/512x/mpc512x_shared.c: In function 'mpc512x_init_early':
.../arch/powerpc/platforms/512x/mpc512x_shared.c:456:3: error: implicit declaration of function 'mpc512x_init_diu' [-Werror=implicit-function-declaration]
.../arch/powerpc/platforms/512x/mpc512x_shared.c: In function 'mpc512x_setup_arch':
.../arch/powerpc/platforms/512x/mpc512x_shared.c:469:3: error: implicit declaration of function 'mpc512x_setup_diu' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[4]: *** [arch/powerpc/platforms/512x/mpc512x_shared.o] Error 1
Signed-off-by: Gerhard Sittig <gsi@denx.de>
CC: <stable@vger.kernel.org> # v3.11
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Merge three fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
memcg: use __this_cpu_sub() to dec stats to avoid incorrect subtrahend casting
percpu: fix this_cpu_sub() subtrahend casting for unsigneds
mm/pagewalk.c: fix walk_page_range() access of wrong PTEs
this_cpu_sub() is implemented as negation and addition.
This patch casts the adjustment to the counter type before negation to
sign extend the adjustment. This helps in cases where the counter type
is wider than an unsigned adjustment. An alternative to this patch is
to declare such operations unsupported, but it seemed useful to avoid
surprises.
This patch specifically helps the following example:
unsigned int delta = 1
preempt_disable()
this_cpu_write(long_counter, 0)
this_cpu_sub(long_counter, delta)
preempt_enable()
Before this change long_counter on a 64 bit machine ends with value
0xffffffff, rather than 0xffffffffffffffff. This is because
this_cpu_sub(pcp, delta) boils down to this_cpu_add(pcp, -delta),
which is basically:
long_counter = 0 + 0xffffffff
Also apply the same cast to:
__this_cpu_sub()
__this_cpu_sub_return()
this_cpu_sub_return()
All percpu_test.ko passes, especially the following cases which
previously failed:
l -= ui_one;
__this_cpu_sub(long_counter, ui_one);
CHECK(l, long_counter, -1);
l -= ui_one;
this_cpu_sub(long_counter, ui_one);
CHECK(l, long_counter, -1);
CHECK(l, long_counter, 0xffffffffffffffff);
ul -= ui_one;
__this_cpu_sub(ulong_counter, ui_one);
CHECK(ul, ulong_counter, -1);
CHECK(ul, ulong_counter, 0xffffffffffffffff);
ul = this_cpu_sub_return(ulong_counter, ui_one);
CHECK(ul, ulong_counter, 2);
ul = __this_cpu_sub_return(ulong_counter, ui_one);
CHECK(ul, ulong_counter, 1);
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJScKOTAAoJEPYb7NoJr+nL+fwP/1bZKlbqYURXdrjLxHTZGKp3
WBpo8KUYp80nAZpw1SLoOk/78ciulQ0VLifWMebzMd/1qXXnek71jfYusbSb7MeM
e70y9TRtXrfkDPxL12XTXIf6F7JieGtVx0S2jJsGsofmM0w6b723KwZAYZgxACYB
Ec7TSzwaTlBBCI+ZyouS8e4CkS0x/0Mpkj8Ym8FDhKnwTs/mtD9kOcgVBzfz0Bt8
ExtiAsASeDvxUq5zskOiGiEhaNlhbQHd8etLIHEBTRreYQRg8nWTI+fdKKqwHKi0
qHm7p/ZcVQUgqf/2EjEfbEa0sQrQKrH82oaJirY3A6QrIEVQ5OVZCThkcvVV5Bxo
w1jDJcxYl2PEM/awR1YkRT3KQKb13J2PxbLFTYnKyhKgZz4mvB/NnjI1AuskTiS8
ddYfJ5apOqtZBqIYQvM6fv69mSWNinhmOqze14ulxGn+U6CVEYsGcQY1QvgA7T+c
0JAAUJwgRsJ+jIDjzx4EJFYCEpdRY8NAKNnZmPr8maP7DIttsbZd0KjWTTqg1Y1N
RHJkxJtnSxJYxfXkgpADJJNjcPdYxqfoYSpcRrGpFM3XLyCPKu2FiahpACyjua3W
JPzRGuYr4I51D16uHiYLxkDSwBKLYBlzyi5bzb+hed9nhoeynvOYtZZkuVgqVRKT
QJwnbUpxU1m870cNpAm/
=fAes
-----END PGP SIGNATURE-----
Merge tag 'bcm-for-3.13-soc2' of git://github.com/broadcom/bcm11351 into next/soc
From Christian Daudt, BCM changes for 3.13/soc. Mostly cleanups and
renaming of kernel config options, pushing down the mobile platforms
one level in the naming scheme, keeping ARCH_BCM as a wider family
config option.
* tag 'bcm-for-3.13-soc2' of git://github.com/broadcom/bcm11351:
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: bcm281xx: more descriptive machine string
ARM: bcm281xx: Enable GPIO driver
Signed-off-by: Olof Johansson <olof@lixom.net>
The OpenBlocks A7 board is designed and sold by PlatHome, and based on
a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
already supported in the kernel, with the following main differences:
- The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.
- The A6 has one Ethernet port, while the A7 has two Ethernet ports
- The A6 has only one USB port, while the A7 integrates a USB hub,
which provides two front-side USB port, and an internal USB port as
well.
- The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.
- Slightly different GPIOs for some functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
name, and using a better the error code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=GwaF
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Fixes for the 3.12 debugfs problem - removing the duplicate directory
name, and using a better the error code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: use a more sensible error number when debugfs directory creation fails
KVM: Fix modprobe failure for kvm_intel/kvm_amd
We don't cap the size of buffer from the user so we could write past the
end of the array here. Only root can write to this file.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently use some ad-hoc arch variables tied to legacy KVM device
assignment to manage emulation of instructions that depend on whether
non-coherent DMA is present. Create an interface for this, adapting
legacy KVM device assignment and adding VFIO via the KVM-VFIO device.
For now we assume that non-coherent DMA is possible any time we have a
VFIO group. Eventually an interface can be developed as part of the
VFIO external user interface to query the coherency of a group.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Default to operating in coherent mode. This simplifies the logic when
we switch to a model of registering and unregistering noncoherent I/O
with KVM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So far we've succeeded at making KVM and VFIO mostly unaware of each
other, but areas are cropping up where a connection beyond eventfds
and irqfds needs to be made. This patch introduces a KVM-VFIO device
that is meant to be a gateway for such interaction. The user creates
the device and can add and remove VFIO groups to it via file
descriptors. When a group is added, KVM verifies the group is valid
and gets a reference to it via the VFIO external user interface.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Once the cpu_logical_map for any logical cpu is populated with the
corresponding physical identifier(i.e. mpidr), it's device node can
be retrieved using the DT helper 'of_get_cpu_node'. Currently the
device tree parsing code to get boot cpu node is duplicated in
'cpu_read_bootcpu_ops'.
This patch replaces the code parsing the device tree for the boot
cpu with of_get_cpu_node.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This basically came from the need to be able to boot 32-bit Atom SMP
guests on an AMD host, i.e. a host which doesn't support MOVBE. As a
matter of fact, qemu has since recently received MOVBE support but we
cannot share that with kvm emulation and thus we have to do this in the
host. We're waay faster in kvm anyway. :-)
So, we piggyback on the #UD path and emulate the MOVBE functionality.
With it, an 8-core SMP guest boots in under 6 seconds.
Also, requesting MOVBE emulation needs to happen explicitly to work,
i.e. qemu -cpu n270,+movbe...
Just FYI, a fairly straight-forward boot of a MOVBE-enabled 3.9-rc6+
kernel in kvm executes MOVBE ~60K times.
Signed-off-by: Andre Przywara <andre@andrep.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add initial support for handling three-byte instructions in the
emulator.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call it EmulateOnUD which is exactly what we're trying to do with
vendor-specific instructions.
Rename ->only_vendor_specific_insn to something shorter, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a field to the current emulation context which contains the
instruction opcode length. This will streamline handling of opcodes of
different length.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a kvm ioctl which states which system functionality kvm emulates.
The format used is that of CPUID and we return the corresponding CPUID
bits set for which we do emulate functionality.
Make sure ->padding is being passed on clean from userspace so that we
can use it for something in the future, after the ioctl gets cast in
stone.
s/kvm_dev_ioctl_get_supported_cpuid/kvm_dev_ioctl_get_cpuid/ while at
it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GIC interrupt offsets are calculated based on the value of NR_CPUS.
However, this is wrong because NR_CPUS may or may not contain the real
number of the actual cpus present in the system. We fix that by using
the 'nr_cpu_ids' variable which contains the real number of cpus in
the system. Previously, an MT core (eg with 8 VPEs) will fail to boot if
NR_CPUS was > 8 with the following errors:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/chip.c:670 __irq_set_handler+0x15c/0x164()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.12.0-rc5-00087-gced5633 5
Stack : 00000006 00000004 00000000 00000000 00000000 00000000 807a4f36 00000053
807a0000 00000000 80173218 80565aa8 00000000 00000000 00000000 0000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 0000000
00000000 00000000 00000000 8054fd00 8054fd94 80500514 805657a7 8016eb4
807a0000 80500514 00000000 00000000 80565aa8 8079a5d8 80565766 8054fd0
...
Call Trace:
[<801098c0>] show_stack+0x64/0x7c
[<8049c6b0>] dump_stack+0x64/0x84
[<8012efc4>] warn_slowpath_common+0x84/0xb4
[<8012f00c>] warn_slowpath_null+0x18/0x24
[<80173218>] __irq_set_handler+0x15c/0x164
[<80587cf4>] arch_init_ipiirq+0x2c/0x3c
[<805880c8>] arch_init_irq+0x3c4/0x4bc
[<80588e28>] init_IRQ+0x3c/0x50
[<805847e8>] start_kernel+0x230/0x3d8
---[ end trace 4eaa2a86a8e2da26 ]---
This is now fixed and the Malta board can boot with any NR_CPUS value
which also helps supporting more processors in a single kernel binary.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
OF/DT core library provides architecture specific hook to match the
logical cpu index with the corresponding physical identifier.
On ARM64, the MPIDR_EL1 contains specific bitfields(MPIDR_EL1.Aff{3..0})
which uniquely identify a CPU, in addition to some non-identifying
information and reserved bits. The ARM cpu binding defines the 'reg'
property to only contain the affinity bits, and any cpu nodes with other
bits set in their 'reg' entry are skipped.
This patch overrides the weak definition of arch_match_cpu_phys_id
with ARM64 specific version using MPIDR_EL1.Aff{3..0} as cpu physical
identifiers.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some drivers (ACPI notably) use ioremap_cache() to map an area which could
either be outside of kernel RAM or in an already mapped reserved area of
RAM. To avoid aliases with different caching attributes, ioremap() does
not allow RAM to be remapped. But for ioremap_cache(), the existing kernel
mapping may be used.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The x86 specific kvm init creates a new conflicting
debugfs directory which causes modprobe issues
with kvm_intel and kvm_amd. For example,
sudo modprobe kvm_amd
modprobe: ERROR: could not insert 'kvm_amd': Bad address
The simplest fix is to just rename the directory. The following
KVM config options are set:
CONFIG_KVM_GUEST=y
CONFIG_KVM_DEBUG_FS=y
CONFIG_HAVE_KVM=y
CONFIG_HAVE_KVM_IRQCHIP=y
CONFIG_HAVE_KVM_IRQ_ROUTING=y
CONFIG_HAVE_KVM_EVENTFD=y
CONFIG_KVM_APIC_ARCHITECTURE=y
CONFIG_KVM_MMIO=y
CONFIG_KVM_ASYNC_PF=y
CONFIG_HAVE_KVM_MSI=y
CONFIG_HAVE_KVM_CPU_RELAX_INTERCEPT=y
CONFIG_KVM=m
CONFIG_KVM_INTEL=m
CONFIG_KVM_AMD=m
CONFIG_KVM_DEVICE_ASSIGNMENT=y
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
[Change debugfs directory name. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several of the options in bcm_defconfig have gotten out of date so
regenerate it with "make savedefconfig" to keep things fresh.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Add HAVE_ARM_ARCH_TIMER to Broadcom Kconfig as it is
required for some Mobile SoCs.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Reviewed-by: Mark Hambleton <mahamble@broadcom.com>
Reviewed-by: James King <jamesk@broadcom.com>
Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Olof Johansson <olof@lixom.net>
Changes from v2:
- switch ARCH_MULTIPLATFORM from select to depends
- remove 'default y' from BCM_MOBILE
Changes from v1:
- fix alpha ordering in dts/Makefile
- break into 4 patches for separate subsys
Code update interface for powernv platform. This provides
sysfs interface to pass new image, validate, update and
commit images.
This patch includes:
- Below OPAL APIs for code update
- opal_validate_flash()
- opal_manage_flash()
- opal_update_flash()
- Create below sysfs files under /sys/firmware/opal
- image : Interface to pass new FW image
- validate_flash : Validate candidate image
- manage_flash : Commit/Reject operations
- update_flash : Flash new candidate image
Updating Image:
"update_flash" is an interface to indicate flash new FW.
It just passes image SG list to FW. Actual flashing is done
during system reboot time.
Note:
- SG entry format:
I have kept version number to keep this list similar to what
PAPR is defined.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create /sys/firmware/opal directory. We wil use this
interface to fetch opal error logs, firmware update, etc.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a VMX optimised xor, used primarily for RAID5. On a POWER7 blade
this is a decent win:
32regs : 17932.800 MB/sec
altivec : 19724.800 MB/sec
The bigger gain is when the same test is run in SMT4 mode, as it
would if there was a lot of work going on:
8regs : 8377.600 MB/sec
altivec : 15801.600 MB/sec
I tested this against an array created without the patch, and also
verified it worked as expected on a little endian kernel.
[ Fix !CONFIG_ALTIVEC build -- BenH ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Correct reference to the location of the kexec_sequence() assembly helper.
There never was a kexec_stub.S in mainline.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The condition register (CR) is a 32 bit quantity so we should use
32 bit loads and stores.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable a few modules required to boot on a POWER multipath
box.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Run savedefconfig over the ppc64, ppc64e and pseries config
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Using -mcpu=power7 allows gcc to use a number of new instructions
including 64 bit byte reversed loads.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit f13c13a005 (powerpc: Stop using non-architected shared_proc
field in lppaca) fixed a potential issue with shared/dedicated
partition detection. The old method of detection relied on an
unarchitected field (shared_proc), and this patch switched
to using something architected (a non zero yield_count).
Unfortunately the assertion in the Linux header that yield_count
is only non zero on shared processor partitions is not true. It
turns out dedicated processor partitions can increment yield_count
and as such we falsely detect dedicated partitions as shared.
Fix the comment, and switch back to using the old method.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch addresses unaligned single precision floating point loads
and stores in the single-step code. The old implementation
improperly treated an 8 byte structure as an array of two 4 byte
words, which is a classic little endian bug.
Signed-off-by: Tom Musta <tmusta@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch modifies the unaligned access routines of the sstep.c
module so that it properly reverses the bytes of storage operands
in the little endian kernel kernel. This is implemented by
breaking an unaligned little endian access into a combination of
single byte accesses plus an overal byte reversal operation.
Signed-off-by: Tom Musta <tmusta@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables alignment handling for the load/store floating point
pair instructions (lfdp, lfdpx, stfdp, stfdpx). The handler routine
is properly coded and only needs to be enabled.
Signed-off-by: Tom Musta <tmusta@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The alignment handler is incorrect for unaligned string instructions
in little endian mode. These instructions access data as arrays of
bytes and thus are endian neutral. However, the routine also handles
the load/store multiple instructions, which are NOT endian neutral.
This patch toggles the byte swapping flag for the string instructions
in little endian builds. This effectively disables the byte swapping
logic.
Signed-off-by: Tom Musta <tmusta@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This issue was causing the QEMU emulated USB device to fail dring
PCI probe.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PPC44x supports page sizes other than 4K however when 64K page sizes
are selected compilation fails. This is due to a change in the
definition of pgtable_t introduced by the following patch:
commit 5c1f6ee9a3
Author: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
powerpc: Reduce PTE table memory wastage
The above patch only implements the new layout for PPC64 so it doesn't
compile for PPC32 with a 64K page size. Ideally we should implement
the same layout for PPC32 however for the meantime this patch reverts
the definition of pgtable_t for PPC32.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If you try and build the FA_DUMP code with CONFIG_KEXEC=n, you see
errors such as the following:
arch/powerpc/kernel/fadump.c
408:2: error: 'crashing_cpu' undeclared (first use in this function)
410:2: error: implicit declaration of function 'crash_save_vmcoreinfo'
513:22: error: storage size of 'prstatus' isn't known
520:2: error: implicit declaration of function 'elf_core_copy_kernel_regs'
521:36: error: 'KEXEC_CORE_NOTE_NAME' undeclared (first use in this function)
624:49: error: 'note_buf_t' undeclared (first use in this function)
872:2: error: implicit declaration of function 'paddr_vmcoreinfo_note'
874:18: error: 'vmcoreinfo_max_size' undeclared (first use in this function)
This is because although FA_DUMP doesn't use kexec as the actual reboot
mechanism, it does use parts of the kexec code to assemble/disassemble
the crash image.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes typo in comments virtual to physical
address conversion.
Signed-off-by: Vaishnavi Bhat <vaishnavi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the few declarations from arch/powerpc/kernel/setup.h
into arch/powerpc/include/asm/setup.h. This resolves a
sparse warning for arch/powerpc/mm/numa.c which defines
do_init_bootmem() but can't include the setup.h header
in the prior path.
Resolves:
arch/powerpc/mm/numa.c:998:13:
warning: symbol 'do_init_bootmem' was not declared.
Should it be static?
Signed-off-by: Robert C Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simple fixes for sparse warnings in this file.
Resolves:
arch/powerpc/mm/numa.c:198:24:
warning: Using plain integer as NULL pointer
arch/powerpc/mm/numa.c:1157:5:
warning: symbol 'hot_add_node_scn_to_nid' was not declared.
Should it be static?
arch/powerpc/mm/numa.c:1238:28:
warning: Using plain integer as NULL pointer
arch/powerpc/mm/numa.c:1538:6:
warning: symbol 'topology_schedule_update' was not declared.
Should it be static?
Signed-off-by: Robert C Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit c55aef0e5b ("powerpc/boot: Change the load address for the
wrapper to fit the kernel") adjusts the wrapper address unnecessarily
for platforms that use arch/powerpc/boot/of.c, since the code there
allocates space for the kernel wherever it can find it and doesn't
necessarily load the kernel at address 0. Changing the link address
is actually harmful since it can cause the zImage to overlap with
Open Firmware and thus fail to boot.
To fix this, we set make_space to n for all of the platforms that
use of.o.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Caused by commit a4da0d50b2 ("powerpc: Implement
arch_get_random_long/int() for powernv") from the powerpc tree
interacting with commit b5b4bb3f6a ("of: only include prom.h on sparc")
from the dt-rh tree.
I added this merge fix patch (which will need to be sent to Linus when
these two trees get merged, or could be applied now to the powerpc tree):
[ Also add linux/smp.h to get cpu_to_chip_id -- BenH ]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the COMMON_CLKDEV kernel configuration
parameter defined in arch/c6x/Kconfig, but used nowhere
in the makefiles and source code.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
On TC2, the cpu clocks are controlled by the external M3 microcontroller
and SPC provides the interface between the CPU and the power controller.
The generic cpufreq drivers use the clock APIs to get the cpu clocks.
This patch add virtual spc clocks for all the cpus to control the cpu
operating frequency via the clock framework.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Pawel Moll <Pawel.Moll@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SPC(Serial Power Controller) on TC2 also controls the CPU performance
operating points which is essential to provide CPU DVFS. The M3
microcontroller provides two sets of eight performance values, one set
for each cluster (CA15 or CA7). Each of this value contains the
frequency(kHz) and voltage(mV) at that performance level. It expects
these performance level to be passed through the SPC PERF_LVL registers.
This patch adds support to populate these performance levels from M3,
build the mapping to CPU OPPs at the boot and then use it to get and
set the CPU performance level runtime.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Pawel Moll <Pawel.Moll@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert ep93xx to use the OHCI platform driver and remove the
ohci-ep93xx bus glue driver.
Enable CONFIG_OHCI_HCD_PLATFORM in the ep93xx_defconfig so that USB
is still enabled by default on the EP93xx platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Highlights include corenet board file consolidation, the ability to run
userspaces with lwsync on e500v1/v2, some cleanup patches that other KVM
patches will build on, support for stripped-down e6500 emulation targets,
and some fixes of minor longstanding issues.
make panda display work with recent u-boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=MMCL
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Few device tree changes that fix boot time warnings and
make panda display work with recent u-boot.
* tag 'omap-for-v3.13/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson reported:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_idmap':
arch/arm/include/asm/memory.h:300:6: error: 'arch_virt_to_idmap' undeclared (first use in this function)
caused by arch_virt_to_idmap being placed inside a different
preprocessor conditional to its user. Move it along side its user.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pcibios_last_bus was apparently copied from x86. On mn10300, it is
statically initialized to -1 and may be set with the "pci=lastbus=<X>"
boot option, but it is never tested. This patch removes everything
related to pcibios_last_bus.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcibios_last_bus was apparently copied from x86. On FR-V, it is
statically initialized to -1 and never changed unless the user boots
with "pci=lastbus=<X>". I doubt that option is used on FR-V, so this
patch removes all the code related to pcibios_last_bus.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
New u-boot versions no longer set the pinmuxing for Panda's DPI output,
and the muxing has to be done in the .dts file.
Add pinmuxing for DPI and TFP410. Without these, the DVI output on Panda
does not work with recent u-boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the AM33xx RNG module's device tree data.
Also add Documentation file describing the data
for the RNG module.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwspinlock device tree node for AM33xx family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwspinlock device tree node for OMAP4 family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An NMI exception delivered from YAMON delivers the PC in ErrorPC
instead of EPC. It's also necessary to clear the Status.BEV
bit for the page fault exception handler to work properly.
[ralf@linux-mips: Let the assembler do the loading of the mask value rather
than the convoluted explicit %hi/%lo manual relocation sequence from the
original patch.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6035/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6084/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PIIX4_ICTLR* and PIIX4_OCW* defines are not used by any other files.
Remove them.
The only file (other than fixup-malta.c which includes piix4.h in patch #1)
containing "#include <asm/mips-boards/piix4.h>" is
arch/mips/mti-malta/malta-int.c whose first version is actually
"1da177e4c3:arch/mips/mips-boards/malta/malta_int.c". In that version, in
the function get_int(), things in piix4.h are used. But now malta-int.c no
longer needs those stuff.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the code more readable by using defines.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Always register the R4K clocksource when CONFIG_CSRC_R4K is selected,
regardless of selected support for other clocksources. The kernel will
select the best clocksource based on their ratings, making it safe to
register R4K unconditionally and use it as a fallback should the
kernel be run on a system where other selected clocksources are
inoperable.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Checking for n<0 && n>9 makes no sense because it can never
be true. Moreover, we can have up to 64 vectored interrupts
so BUG_ON(n>9) was wrong anyway.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5909/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nobody seems to care about this platform anymore and my attempts to find
somebody willing to provide some tlc for PowerTV have failed so far.
So let's nuke the bloody thing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5910/
There are no users yet of task_user_regset_view. yet; users will be
implemented rsp activated in subsequent commits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This gets us rid of the hard to maintain table of the number of syscall
arguments and paves the way for further restructuring of the syscall
code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These are a leftover of the IRIX compat code which was removed in
2957c9e61e (kernel.org) rsp.
b934da913f236bca00c41d9e386e980586000461 (lmo) [[MIPS] IRIX: Goodbye
and thanks for all the fish].
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow usage of scratch register for current pgd even when
MIPS_PGD_C0_CONTEXT is not configured. MIPS_PGD_C0_CONTEXT is set
for 64r2 platforms to indicate availability of Xcontext for saving
cpuid, thus freeing Context to be used for saving PGD. This option
was also tied to using a scratch register for storing PGD.
This commit will allow usage of scratch register to store the current
pgd if one can be allocated for the platform, even when
MIPS_PGD_C0_CONTEXT is not set. The cpuid will be kept in the CP0
Context register in this case.
The code to store the current pgd for the TLB miss handler is now
generated in all cases. When scratch register is available, the PGD
is also stored in the scratch register.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/5906/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is no reliable way to tell R4000/R4400 SC and MC variations apart,
however simple heuristic should give good results. Only the MC version
supports coherent caching so we can rely on such a mode having been set
for KSEG0 by the power-on firmware to reliably indicate an MC processor.
SC processors reportedly hang on coherent cached memory accesses and Linux
is linked to a cached load address so the firmware has to use the correct
caching mode to download the kernel image in a cached mode successfully.
OTOH if the firmware chooses to use either the non-coherent cached or the
uncached mode for KSEG0 on an MC processor, then the SC variant will be
reported, just as we currently do, so no regression here.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change complements commits d0da7c002f7b2a93582187a9e3f73891a01d8ee4
[MIPS: DEC: Convert to new irq_chip functions] and
5359b938c0 [MIPS: DECstation I/O ASIC DMA
interrupt handling fix] and implements automatic handling of the two
classes of DMA interrupts the I/O ASIC implements, informational and
errors.
Informational DMA interrupts do not stop the transfer and use the
`handle_edge_irq' handler that clears the request right away so that
another request may be recorded while the previous is being handled.
DMA error interrupts stop the transfer and require a corrective action
before DMA can be reenabled. Therefore they use the `handle_fasteoi_irq'
handler that only clears the request on the way out. Because MIPS
processor interrupt inputs, one of which the I/O ASIC's interrupt
controller is cascaded to, are level-triggered it is recommended that
error DMA interrupt action handlers are registered with the IRQF_ONESHOT
flag set so that they are run with the interrupt line masked.
This change removes the export of clear_ioasic_dma_irq that now does not
have to be called by device drivers to clear interrupts explicitly
anymore. Originally these interrupts were cleared in the .end handler of
the `irq_chip' structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The semantics stay the same - on Cavium Octeon the functions were dead
code (it overrides the MIPS DMA ops) - on other platforms they contained
no code at all.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the LZ4 compression scheme in the ZBOOT decompression
stub, in order to support it we need to:
- select the "lz4" compression tool to compress the vmlinux.bin
payload
- memcpy() is also required for decompress_unlz4.c so we share the
implementation between GZIP, XZ and now LZ4
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5829/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is currently no corresponding ELF program header for the "text"
loadable segment which is confusing for some bootloader out there such
as CFE because it expects to find a program header matching the segment
it is trying to load. The Linux kernel ELF binary "vmlinux" has a
similar program header for the text segment so we just mimic this here
too.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5827/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the XZ compression scheme in the ZBOOT decompression
stub, in order to support it we need to:
- select the "xzkern" compression tool to compress the vmlinux.bin
payload
- link with ashldi3.o for xz_dec_run() to work
- memcpy() is also required for decompress_unxz.c so we share the
implementation between GZIP and XZ
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5818/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CONFIG_SYS_SUPPORTS_ZBOOT is not enabled, we will still try to
build the decompressor code in arch/mips/boot/compressed as a
dependency for producing the vmlinuz target and this will result in
the following build failure:
OBJCOPY arch/mips/boot/compressed/vmlinux.bin
arch/mips/boot/compressed/decompress.c: In function 'decompress_kernel':
arch/mips/boot/compressed/decompress.c:105:2: error: implicit
declaration of function 'decompress'
make[1]: *** [arch/mips/boot/compressed/decompress.o] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [vmlinuz] Error 2
This is a genuine build failure because we have no implementation for
the decompress() function body since no kernel compression method
defined in CONFIG_KERNEL_(GZIP,BZIP2...) has been enabled.
arch/mips/Makefile already guards the install target for the "vmlinuz"
binary with a proper ifdef CONFIG_SYS_SUPPORTS_ZBOOT, we now also do the
same if we attempt to do a "make vmlinuz" and show that
CONFIG_SYS_SUPPORTS_ZBOOT is not enabled.
[ralf@linux-mips.org: Cleanup the makefile rule as suggested by James
Hogan.]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: richard@nod.at
Patchwork: https://patchwork.linux-mips.org/patch/5817/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently when using an initrd on a MIPS system the start of the bootmem
region of memory is set to the larger of the end of the kernel bss region
(_end) or the end of the initrd. In a typical memory layout where the
initrd is at some address above the kernel image this means that the start
of the bootmem region will be the end of the initrd. But when we are done
processing/loading the initrd we have no way to reclaim the memory region
it occupied, and we lose a large chunk of now otherwise empty RAM from our
final running system.
The bootmem code is designed to allow this initrd to be reserved (and the
code in finalize_initrd() currently does this). When the initrd is finally
processed/loaded its reserved memory is freed.
Fix the setting of the start of the bootmem map to be the end of the kernel.
[ralf@linux-mips.org: fold in the fix of Ashok Kumar <ashoks@broadcom.com>.]
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1574/
Cc: Ashok Kumar <ashoks@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5883/
Patchwork: https://patchwork.linux-mips.org/patch/6028/
Patchwork: https://patchwork.linux-mips.org/patch/6064/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on quiet_cmd_X and cmd_X, this patch quiets the building output of
vmlinux.32 and vmlinux.64.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1766/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the pci_load_of_ranges function to use the new common
of_pci_range_parser.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Andrew Murray <Andrew.Murray@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Patchwork: https://patchwork.linux-mips.org/patch/5625/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Asus WL520GC and WL520GU are based on the BCM5354 and clocked at
200MHz, but they do not have a clkfreq nvram variable set to the
correct value. This adds a workaround for these devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5843/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some BCM5354 SoCs are running at 200MHz, but it is not possible to read
the clock from a register like it is done on some other SoC in ssb and
bcma. These devices should have a clkfreq nvram configuration value set
to 200, read it and set the clock to the correct value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The nvram contains some gpio configuration for boards. It is stored in
a gpio<number>=name format e.g.
gpio8=wps_button
gpio4=robo_reset
This patches adds a function to parse these entries, so other driver
can use it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not print the constant system type "Broadcom BCM47XX" but print the
name of the actual SoC in use and the detected board.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
