We send SYSTEM_CONFIG command after the TGI_KEY command if hardware
encryption is enabled. It sometimes causes a firmware stall (firmware
doesn't respond to any request) and finally bungs up the Tx send queue.
The solution is to send SYSTEM_CONFIG command in the post association
stage from a workqueue.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fixed#452 problem with setting retry limit (thanks to Hong Liu)
* Fixed#592 race condition during association causing firmware errors
* Fixed#602 problem with building in 64-bit environment
* Fixed#625 problem with SCAN_REQUEST_EXT sometimes failing
* Fixed#645 problem with bit rate not decreasing when moving laptop
farther from AP
* Fixed#656 problem with 'iwconfig eth1 mode auto' and 'modprobe'
locking the system
* Fixed#667 problem with "No space for Tx" for hwcrypto=1
* Fixed#685 kernel panic in rmmod caused by led work is still queued
* Fixed#695 problem with network doesn't reassociate after suspend/resume
* Fixed#701 problem with 'iwprvi sw_reset' not resetting the card from
monitor mode
* Fixed#710 problem with monitor mode being used after a WEP key has
been configured
* Fixed network->mode vs. priv->ieee->iw_mode checking (thanks to Ben Cahill)
* Fixed "Unknown management packet %d" warning
* Fixed setting channels multiple times in monitor mode causes scan stopped
* Fixed ipw_wx_sw_reset doesn't switch firmware if mode is changed.
* Add duplicate packet checking code (kill ping DUP! and TKIP replay warning)
* Fix hardware encryption (both WEP and AES) doesn't work with fragmentation.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
support wpa_supplicant with open AP. We need this to make driver_ipw
work.
driver_ext has already had the similar code with the WE-18 support
added.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Added WE-18 support. This allows the use of -Dext with wpa_supplicant
> 0.4.x (thanks to Hong Liu)
* Fixed#339 problem with iwconfig set/get txpower (thanks to Hong Liu)
* Fixed#598 problem when with error messages when module loaded with
'disable=1' (thanks to Hong Liu)
* Fixed#640 problem with 'iwlist retry' now showing min/max retry
* Fixed compatibility with wpa_supplicant and the new -Dipw interface
(that included a fix for 64-bit compatibility)
* Added CFG_CRC_CHECK which allows passing through packets with bad
CRCs while in monitor mode.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fixed#627 problem with open APs not working with wpa_supplicant
* Fixed#632 problem with 'txpower auto' setting power incorrectly (thanks
to Kai Groner)
* Fixed#634 problem with 'iwconfig eth1 frag 0' hanging the shell
* Fixed problem with adapter not fully powering off during suspend to RAM or
when module unloaded.
* Fixed#645 problem with turning fixed rates off not taking effect until
you reload the driver
* Fixed problem with firmware restart if wpa_supplicant was used to set a key
that wasn't exactly 5 or 13 bytes in length.
* Fixed#623 Added iwpriv sw_reset extension to reset sw parameters
* Added managment frame export to user space with frame statistics
* Fixed#652 Modified the driver to load the EEPROM data even if RF KILL is
active during driver load
* Global s:CX2_:IPW_:g to make code more consistent
* Fixed#572 problem with setting txpower to auto
* Fixed#656 problem with kernel oops if mode auto; modprobe -r ipw2200
* Added QoS (CONFIG_IPW_QOS) support. This is being actively developed but
is the first step in getting WMM support into the driver and the kernel.
* Fixed some race conditions with channel changes, association, and scan
abort that could periodically cause a firmware restart.
* Added some extensions to export scan and network statistics to user space
(exposed through speed_scan and net_stats sysfs entries)
* Fixed a few bugs in how monitor mode was supported (scan lists
weren't quite right)
* Updated the firmware requirement from 2.2 to 2.3 which supports
monitor mode.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fix#616 problem with OOPS on module load (thanks to Yi Zhu)
* Fixed problem with led module parameter being described as
'auto_create'
* Added support to merge between adhoc networks (thanks to Mohamed Abbas)
* Added semaphore lock at the driver's entry points to protect against
re-entry (thanks to Mohamed Abbas)
* Added semaphore lock to background scheduled driver actions (thanks to
Mohamed Abbas)
* Changed how signal quality is reported for scan output (thanks to
Peter Jones)
* Fixed how high/low clamp values of signal quality are reported so a
more consistent ramp is provided (thanks to Bill Moss)
* Fix#624 problem with duplicate addresses (again) (thanks to Bernard
Blackham)
* Fix#385 problem with fragmentation and certain sized packets (thanks
to Mohamed Abbas)
* Modified iwconfig network name if RF kill is enabled to say 'radio off'
* Fix#382 problem with driver not responding to probe requests in Ad-Hoc
mode (thanks to Mohamed Abbas)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Removed unneeded parenthesis around numeric constant defines
Added support for iwspy
Put in fix for Ad-Hoc mode not passing through all packets (thanks to KKH)
Put in fix for fragmentation not working for fragment sizes between
441-464 bytes (thanks to Mohamed Abbas)
Fixed#592 problem of CONFIG_IEEE80211_WPA_MODULE not including WPA
support into the driver -- fixed as a result of no longer limiting WPAs
inclusion
Fixed#594 problem with user rates mask causing lack of association if
AP mandatory rate is masked out. We now add back in as a supported rate
any mandatory rate.
Fixed#597 kernel oops due to calling dev_kfree_skb on an skb multiple times.
Added code to control LEDs that can be controlled through the wireless
NIC (vs. non-wireless HW interfaces) -- this is currently disabled by
default due to reports by some users of it hanging their laptop.
Added some more debug messages around fragmentation logic
Added locking around STATUS_HCMD_ACTIVE to prevent re-entry race
conditions
Moved ipw_adapter_restart to only execute on the priv->workqueue to
keep keyboard errors from occuring during adapter restart
Added CFG_BACKGROUND_SCAN to easily allow people to play with
background scanning implementations
Modified WPA logic to send WPA IE if one is set (vs. being based on
wpa_enabled)
Modified scan result logic to report WPA and RSN IEs if set (vs. being
based on wpa_enabled)
Fixed issues with endianess compatability between the host and
wireless adapter (thanks to York Liu and Yi Zhu)
Fixed problem with Ad-Hoc network creation causing a firmware error if
a scan was actively running (thanks to Mohamed Abbas)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
This commit contains the following fixes:
Fixed#559: iwconfig rate support (thanks to Florian Hackenberger)
Improved link signal quality calculation (thanks to Bill Moss)
Fixed a problem with sensitivity threshold during association
Added iwpriv for turning forcing long preamble support:
% iwpriv eth1 set_preamble 1|0
Fixed#542 and #377 support for short preamble
Fixed locked BSSID reporting channel number (thanks to Pedro
Ramalhais)
Fixed type-o with scan watchdog timeout message (thanks to Pedro
Ramalhais)
Changed logic for displaying get_mode output so the code is easier to
follow (thanks to Pedro Ramalhais)
Added initial support for WPA (thanks to Yi Zhu) -- tested with
wpa_supplicant (either tip w/ ipw driver, or with -Dipw2100) with
both CCMP and TKIP
Fixed problem with CCMP not working due to uninitialized 802.11
header fields (thanks to Pedro Ramalhais)
Bug references are to defects stored on http://bughost.org
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
This patch creates a file airo.h containing prototypes of the global
functions in airo.c used by airo_cs.c .
If you got strange problems with either airo_cs devices or in any other
completely unrelated part of the kernel shortly or long after a airo_cs
device was detected by the kernel, this might have been caused by the
fact that caller and callee disagreed regarding the size of the first
argument to init_airo_card()...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch I sent in ("prism54: Free skb after disabling
interrupts") included a redundant NULL assignment. Thanks to Herbert
Xu for pointing it out.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fid is declared as a u32 (unsigned int), and then a few lines later, it is checked for a value < 0, which is clearly useless.
In the two locations this function is used, in one it is *explicitly* given a negative number, which would be ignored with the
current definition.
Thanks to LinuxICC (http://linuxicc.sf.net).
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch rewrites various occurences of &sg[0] where sg is an array
of length one to simply sg.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch uses sg_set_buf/sg_init_one in some places where it was
duplicated.
Signed-off-by: David Hardeman <david@2gen.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The dev_kfree_skb in islpci_eth_transmit happens while irqs are still
disabled, so either dev_kfree_skb_irq needs to be used or the skb
needs to be freed after irqs have been enabled again. This patch
should fix it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The latest kernel added a pretty ugly fix for the orinoco etherleak bug
which contains bogus skb->len checks already done by the caller and causes
copies of all odd sized frames (which are quite common)
While the skb->len check should be ripped out the other fix is harder to do
properly so I'm proposing for this the -mm tree only until next 2.6.x so
that it gets tested.
Instead of copying buffers around blindly this code implements a padding
aware version of the hermes buffer writing function which does padding as
the buffer is loaded and thus more cleanly and without bogus 1.5K copies.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The ipw2200 driver code in current GIT contains a kmalloc() followed by
a memset() without handling a possible memory allocation failure.
Signed-off-by: Panagiotis Issaris <panagiotis.issaris@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
prism54 is leaking information when passing transmits to the firmware.
There is no requirement to adjust the length to >= ETH_ZLEN.
Just pass the skb length (after possible adjustment).
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Brice Goglin <Brice.Goglin@ens-lyon.org> reports a printk storm from this
driver. Fix.
Acked-by: David Gibson <hermes@gibson.dropbear.id.au>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Checking the skb->len value before calling skb_padto is redundant.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The aironet PCI driver has a build dependency on ISA that prevent the
driver to compile on systems that doesn't support ISA, like x86_64. The
driver really doesn't depend on ISA, it does some ISA stuff in the
initialization code, since the driver supports both ISA and PCI cards. So
the driver should depend on ISA_DMA_API to build on all systems, and this
will not hurt PCI at all.
Signed-off-by: Matteo Croce <3297627799@wind.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The orinoco driver can send uninitialized data exposing random pieces of
the system memory. This happens because data is not padded with zeroes
when its length needs to be increased.
Reported by Meder Kydyraliev <meder@o0o.nu>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cisco Aironet doesn't resume properly from swsusp, because the resume
method confuses a PM_EVENT_* for a PCI power state. It thinks that it is
resuming from PCI_D1 and doesn't do the necessary initialization of the
card.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Unregister all netdevs before freeing local data. I was unable to
trigger any crashes without this change when running busy loops for
driver operations when ejecting a Prism2 PC Card. Anyway, should there
be a race condition with this, better make it less likely to happen by
unregistering the netdevs first.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
local->hw_priv was being freed and set to NULL just before calling
prism2_free_local_data(). However, this may expose a race condition in
which something ends up trying to use hw_priv during shutdown. I
haven't noticed this happening, but better be safe than sorry, so
let's postpone hw_priv freeing to happen only after
prism2_free_local_data() has returned.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The debug version of I/O functions in hostap_pci had not survived the
change to start using hw_priv pointer, so let's fix them to actually
define the local hw_priv variable.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Host AP driver used hardware model specific dev_open/close handlers
that were called on dev_open/close if the hardware driver had
registered the handler. These were only used for hostap_cs and only
for tracking whether any of the netdevs were UP. This information is
already available from local->num_dev_open, so there is not need for
the special open/close handler.
Let's get rid of these handlers. In addition to cleaning up the code,
this fixes a module refcounting issue for hostap_cs where ejecting the
card while any of the netdevs were open did not decrement refcount
properly.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest wireless extensions moved a field from netdev -> wireless_handlers.
The WE core will now printk a warning on every call to get_wireless_stats()
on a driver that still uses the old field. This patch fixes orinoco.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we are compiling with -fno-strict-aliasing (this is the
kernel default), we can drop the following kludge for
iwe_stream_add_event().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for WE-19 to the HostAP driver. One of
the major change is the use of an explicit flag to tell if iwstat is
in dBm or not.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_pci and hostap_plx drivers still use PCI driver names
"prism2_pci" and "prism2_plx" respectively. This is unfriendly to
linux-wlan-ng, which uses the same names. So, if e.g. hostap_pci and
prism2_pci are loaded, they will "share" /sys/bus/pci/drivers/prism2_plx
directory.
Change PCI driver names of hostap_pci and hostap_plx to be equal to
their module names.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Read only needed data in __orinoco_ev_txexc().
Don't read the 802.11 header beyond addr1. The rest of the frame is not
used currently.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Annotate endianess of variables and structure members.
Don't reuse variables for both host-endian and little-endian data.
Minor comment changes in affected structures.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove unneeded forward declarations.
Also reorder struct pcmcia_driver initialization to keep attach and
detach together.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
orinoco_send_wevents() could return without unlocking.
Failure to read BSSID from the hardware would cause orinoco_send_wevents() to
return with lock held. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Fix memory leak and unneeded unlock in orinoco_join_ap()
If orinoco_lock() fails, the code would still run orinoco_unlock(),
instead of freeing the allocated memory. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove inneeded system includes.
Most system includes are not needed. In particular, the hardware
backends don't need anything network related. Some includes have been
moved from local headers to the C files where they are actually used.
Includes that have to be in the local headers are no longer from the C
sources.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 8c1676c8a15c08e6d4c718fc7cd42d9bf4cd8235
parent 0ccc3dd6469ed492578c184f47dde2baccde3593
author James Ketrenos <jketreno@linux.intel.com> 1126715240 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316717 -0500
Updated hostap to be compatible with extra_prefix_len changes.
Accomplished via:
for i in hostap_ap.c hostap_80211_tx.c; do
sed -i -e "s:\([.>]\)extra_prefix_len:\1extra_mpdu_prefix_len:g" \
-e "s:\([.>]\)extra_postfix_len:\1extra_mpdu_postfix_len:g" \
drivers/net/wireless/hostap/$i
done
CC: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 8ec97d9056ceaf0f845ed51175dd842b700baadd
parent 329128457008ace3110c96971addf85a767dd5af
author James Ketrenos <jketreno@linux.intel.com> 1126714484 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316636 -0500
Updated hostap to be compatible with ieee80211_hdr changes.
Change accomplished via:
for i in hostap_ap.{c,h} hostap_80211_{t,r}x.c; do
sed -i -e "s:ieee80211_hdr\([^_]\):ieee80211_hdr_4addr\1:g" \
drivers/net/wireless/hostap/$i
done
CC: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 713b6ff3311decfe42d5209f7b2508736d144b85
parent 6465beff0e89779330450dffc2a5e6dc5154eebf
author James Ketrenos <jketreno@linux.intel.com> 1126716726 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316162 -0500
Updated ipw2200 to be compatible with ieee80211's hard_start_xmit change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 9f86c7b4f59249c05c96c360dfaa817995e8a44f
parent 9b09701b2c6254f2fddb009004a14eb5a908714f
author James Ketrenos <jketreno@linux.intel.com> 1126714305 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316074 -0500
Updated ipw2200 to be compatible with ieee80211_hdr changes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree ee48cbe413b795d6be454b9baf4f3bd3d74814cb
parent 49856b147763bd6847e0d8f53aee1ddd61385638
author James Ketrenos <jketreno@linux.intel.com> 1126716634 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316024 -0500
Updated ipw2100 to be compatible with ieee80211's hard_start_xmit change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 992b203395c50342f1cced415acae6177344e270
parent c59bb604a2ff4e40232ff0422e7adc44e3b007a0
author James Ketrenos <jketreno@linux.intel.com> 1126714006 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127315910 -0500
Updated ipw2100 to be compatible with ieee80211_hdr changes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
author James Ketrenos <jketreno@linux.intel.com> 1126713327 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1126713327 -0500
Updated ipw2200 to compile with ieee80211 abg_ture to abg_true change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Pavel Roskin <proski@gnu.org>
Date: Fri Sep 16 01:07:47 2005 -0400
Update PCMCIA ID's.
Intel Pro/Wireless 2011 and 2011B have the same numeric ID, so use
strings instead.
Take all entries from *.conf for Orinoco, HostAP and linux-wlan-ng and
adds them with minimal changes (e.g. we don't need a revision string
after a string that identifies the chipset).
Add comments with card names to all numeric entries. Note: the comments
don't and cannot cover all cards, since the main reason of having
numeric IDs is to cover cards that are often rebranded.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Pavel Roskin <proski@gnu.org>
Date: Fri Sep 16 00:49:05 2005 -0400
Remove conditionals that are useless in the kernel drivers.
Kernel drivers are never compiled against pcmcia-cs headers.
Firmware is never embedded into spectrum_cs module.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Use new Wireless Extension API for wireless stats.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
this patch display the correct channel number with iwlist scan
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
No code changes, just Lindent + manual fixups.
This prepares us for updating to the latest Intel driver code, plus
gives the source code a nice facelift.
Dan Williams already included most parts of my WE-19 patch for
the airo driver in the kernel. There was just a few bits he could not
do because WE-19 itself was not in the kernel. Those are the missing
bits.
Tested with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
My patch that adds WE-17 support to the Prism54 driver went
already in the kernel, except for a tiny bit that was dropped on the
way. This is the missing bit....
Tested with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
wl3501_cs won't compile with WE-19. This patches fixes it.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Acked-by: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This adds support for WE-17 to the atmel_cs driver. Not
tested, I don't have the HW.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This adds support for WE-17 to the netwave_cs driver. Tested
with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This adds support for WE-17 to the ray_cs driver. Tested
with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
diff-tree dee4f325520d4ea29397dd67ca657b7235bb1790 (from c88faac230cc9775445e5c644991c352e35c72a1)
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 1 17:46:39 2005 -0400
New driver - spectrum_cs.
Driver for 802.11b cards using RAM-loadable Symbol firmware, such as
Symbol Wireless Networker LA4100, CompactFlash cards by Socket
Communications and Intel PRO/Wireless 2011B.
The driver implements Symbol firmware download. The rest is handled
in hermes.c and orinoco.c.
Utilities for downloading the Symbol firmware are available at
http://sourceforge.net/projects/orinoco/
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
diff-tree dce61aef99ceb57370b70222dc34d788666c0ac3 (from ceb6695092be8dcdfe2dec6ee5097d613011489d)
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 1 15:50:55 2005 -0400
New driver - orinoco_nortel.
This is a driver for Nortel emobility PCI adaptors, which consist of an
Orinoco compatible PCMCIA card and a simple PCI-to-PCMCIA bridge. The
driver initializes the device and uses Orinoco core driver for actual
wireless networking.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
diff-tree ceb6695092be8dcdfe2dec6ee5097d613011489d (from 6b39374a27)
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 1 14:50:10 2005 -0400
Remove EXPERIMENTAL mark from PLX_HERMES, TMD_HERMES and PCI_HERMES.
Those drivers have been used for a long time, and there have been very
few problem reports.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
diff-tree cb289b9f9b2a0f3ae7070a008f22e383b37526ee (from 56bfcdb38b3d04c1f8c1fd705e411f4be53b663c)
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 1 19:05:16 2005 -0400
Optimize orinoco_join_ap() - break from loop once the requested
BSSID
is found.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
diff-tree c88faac230cc9775445e5c644991c352e35c72a1 (from dce61aef99ceb57370b70222dc34d788666c0ac3)
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 1 17:09:45 2005 -0400
Remove entry for Intel PRO/Wireless 2011B.
It is not supported by this driver because it has no firmware in
flash. spectrum_cs is needed for this device.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
diff-tree 8fc038ec51acf5f777fade80c5e38112b766aeee (from ca955293cdfd3139e150d3b4fed3922a7eb651fb)
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 1 19:10:12 2005 -0400
Change orinoco_translate_scan() to return error code on error.
Adjust the caller to check for errors and clean up if needed.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This should bits from -mm tree that are affected by pm_message_t
conversion. [I'm not 100% sure I got all of them, but I certainly got all
the errors on make allyesconfig build, and most of warnings, too. I'll go
through the buildlog tommorow and fix any remaining bits].
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
