* Check ide_config_drive_speed() return value.
* While at also call ide_config_drive_speed() if the transfer mode is
XFER_PIO_SLOW (this case happens iff the transfer mode has already been
set on the device by ide-proc.c::set_xfer_rate()) and remove redundant
setting of ->{init,current}_speed.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set transfer mode on the device before programming the host controller for
the new timings (matches what auide_tune_chipset() is doing wrt DMA modes).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "good DMA drives" hack for icside to ide-dma.c::ide_find_dma_mode()
(in the long-term it should be either removed or generalized for all hosts).
* Use ide_tune_dma() in icside.c::icside_dma_check().
This results in the following changes in behavior:
- pre-EIDE SWDMA modes are now also respected
- drive->autodma is checked instead of hwif->autodma
(doesn't really matter as icside sets both to "1")
* Make ide-dma.c::__ide_dma_good_drive() static and drop "__" prefix.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add missing initialization of hwif->autodma and drive->autodma to
pmac_ide_setup_dma().
* Use ide_tune_dma() in pmac_ide_dma_check().
While at it:
* Fix pmac_ide_dma_check() return value if DMA mode is not programmed
(should be "-1" otherwise ide_set_dma() will try to enable DMA).
* Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always
called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if
->ide_dma_check returns "0").
v2:
* No reason to blacklist all ide_floppy devices and the old code was always
enabling DMA anyway (without even programming controller/device if the
device was ide_floppy).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Upper layers are responsible for controlling nIEN so don't clear nIEN after
command execution in pmac_ide_do_setfeature().
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().
While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():
* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.
* Check DRQ_STAT bit (shouldn't be set for good device status).
Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for good device status before executing the command in
pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this).
It is a job of upper layers to guarantee that the device is ready to
accept new command before we get here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off checking of the status register from ide_wait_stat() to
__ide_wait_stat() helper.
* Use the new helper in ide_config_drive_speed(). The only change in the
functionality is that the function now fails if after 20 sec (WAIT_CMD)
device is still busy (BUSY_STAT bit is set) while previously instead of
failing the function continued with checking for the correct device status
(which would give the device additional 10 usec to clear BUSY_STAT bit).
* Remove stale comment for ide_config_drive_speed().
* Remove duplicate comment for ide_wait_stat() from <linux/ide.h>.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer
necessary pmac_ide_{m,u}dma_enable().
* While at it remove some dead code from pmac_ide_dma_check() (leftovers from
conversion to use ide_max_dma_mode()).
There should be no functionality changes caused by this patch.
v2:
* Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check()
(Noticed by Ben).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this
Device Control register messing in pmac_ide_dma_check() is totally unnecessary.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move adjusting of cycle time for devices providing explicit DMA cycle time
from pmac_ide_mdma_enable() to set_timings_mdma().
* Remove no longer needed drive_cycle_time argument.
* BUG() if unsupported speed argument value is passed (shouldn't happen).
* Matching access/recovery timings always exist so remove redundant check.
* Make set_timings_mdma() void.
* Update pmac_ide_tune_chipset()'s comment.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't check check for pmif == NULL (it should never be NULL if we got here).
* Make a local copy of the timings and set the pmif->timings[] only after
setting the transfer mode on the device (otherwise SELECT_DRIVE() call in
pmac_ide_do_setfeature() will program new timings before the transfer mode
is set on the device - this was pointed out by Sergei). This change makes
pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
kauai_lookup_timing() should always return non-zero return value:
* BUG() in kauai_lookup_timing() if the timing info cannot be found.
* Remove code checking for zero return value from all callers.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch removes the unused EXPORT_SYMBOL_GPL(ide_acpi_set_state)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We need to set hwif->chipset or IDE PCI host drivers may try to claim
our ide_hwifs[] slot.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the driver for latest Blackfin on-chip nand flash controller
- use nand_chip and mtd_info common nand driver interface
- provide both PIO and dma operation
- compiled with ezkit bf548 configuration
- use hardware 1-bit ECC
- tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs
ChangeLog from try#1
- use hweight32() instead of count_bits()
- replace bf54x with bf5xx and BF54X with BF5XX
- compare against plat->page_size in 2 cases when enable hardware ECC
ChangeLog from try#2
- passed nand_test suites
- use cpu_relax() instead of busy wait loop
- some coding style issue pointed out by Andrew
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we press ctrl-alt-del,kernel_restart_prepare will invoke
cfi_intelext_reboot which will set flash to read array mode, but later
when device_shutdown is invoked which may put current work queue to
sleep and other process may be scheduled to running and programming
flash in not FL_READY mode again. So we can't boot up if this flash is
used for bootloader.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/alauda.c: In function 'alauda_bounce_read':
drivers/mtd/nand/alauda.c:412: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If we defer updating rip until pio instructions are executed, we have a
problem with reset: a pio reset updates rip, and when the instruction
completes we skip the emulated instruction, pointing rip somewhere completely
unrelated.
Fix by updating rip when we see decode the instruction, not after emulation.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Some operand fetches are less than the machine word size and can result in
stale bits if used together with operands of different sizes.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Implement emulation of instruction
lea r16/r32, m
opcode: 0x8d:
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
According to Intel Software Developer's Manual, Vol. 3B, Appendix H.4.2,
exit qualification should be of natural width. However, current code
uses u64 as the data type for this register, which occasionally
introduces invalid value to VMExit handling logics. This patch fixes
this bug.
I have tested Windows and Linux guest on i386 host, and they can boot
successfully with this patch.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Before preempt notifiers, kvm needed to allocate memory with GFP_NOWAIT so
as not to have to enable preemption and take a heavyweight exit. On oom, we'd
fall back to a GFP_KERNEL allocation.
With preemption notifiers, we can do a GFP_KERNEL allocation, and perform
the heavyweight exit only if the kernel decides to put us to sleep.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch just renames the current (misnamed) _arch namings to _x86 to
ensure better readability when a real arch layer takes place.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The mutex->splinlock convertion alllows us to make some code simplifications.
As we can keep the lock longer, we don't have to release it and then
have to check if the environment has not been modified before re-taking it. We
can remove kvm->busy and kvm->memory_config_version.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
SVM gets the DB and L bits for the cs by decoding the segment. This
is in fact the completely generic code, so hoist it for kvm-lite to use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We don't update the vcpu control registers in various places. We
should do so.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
invlpg shouldn't fetch the "src" address, since it may not be valid,
however SVM's "solution" which neuters emulation of all group 7
instruction is horrible and breaks kvm-lite. The simplest fix is to
put a special check in for invlpg.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This was missed when moving stuff around in fbc4f2e
Fixes Solaris guests and bug #1773613
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables INIT/SIPI handling using in-kernel APIC by
introducing a ->mp_state field to emulate the SMP state transition.
[avi: remove smp_processor_id() warning]
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Xin Li <xin.b.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the PIC interrupts delivery. Now it is only delivered
to vcpu0 when either condition is met (on vcpu0):
1. local APIC is hardware disabled
2. LVT0 is unmasked and configured to delivery mode ExtInt
It fixes the 2x faster wall clock on x86_64 and SMP i386 Linux guests
Signed-off-by: Eddie (Yaozu) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reduces overhead by accessing cachelines from the wrong node, as well
as simplifying locking.
[Qing: fix for inactive or expired one-shot timer]
Signed-off-by: Yaozu (Eddie) Dong <Eddie.Dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
APIC timer IRQ is set every time when a certain period
expires at host time, but the guest may be descheduled
at that time and thus the irq be overwritten by later fire.
This patch keep track of firing irq numbers and decrease
only when the IRQ is injected to guest or buffered in
APIC.
Signed-off-by: Yaozu (Eddie) Dong <Eddie.Dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables TPR shadow of VMX on CR8 access. 64bit Windows using
CR8 access TPR frequently. The TPR shadow can improve the performance of
access TPR by not causing vmexit.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds a new vcpu-based IOCTL to save and restore the local
apic registers for a single vcpu. The kernel only copies the apic page as
a whole, extraction of registers is left to userspace side. On restore, the
APIC timer is restarted from the initial count, this introduces a little
delay, but works fine.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds support for in-kernel ioapic save and restore (to
and from userspace). It uses the same get/set_irqchip ioctl as
in-kernel PIC.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
vcpu->irq_pending is saved in get/set_sreg IOCTL, but when in-kernel
local APIC is used, doing this may occasionally overwrite vcpu->apic to
an invalid value, as in the vm restore path.
Signed-off-by: Qing He <qing.he@intel.com>
This patch adds two new ioctls to dump and write kernel irqchips for
save/restore and live migration. PIC s/r and l/m is implemented in this
patch.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
pio operation and IRQ_LINE kvm_vm_ioctl is not kvm->lock
protected. Add lock to same with IOAPIC MMIO operations.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
By sleeping in the kernel when hlt is executed, we simplify the in-kernel
guest interrupt path considerably.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Because lightweight exits (exits which don't involve userspace) are many
times faster than heavyweight exits, it makes sense to emulate high usage
devices in the kernel. The local APIC is one such device, especially for
Windows and for SMP, so we add an APIC model to kvm.
It also allows in-kernel host-side drivers to inject interrupts without
going through userspace.
[compile fix on i386 from Jindrich Makovicka]
Signed-off-by: Yaozu (Eddie) Dong <Eddie.Dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch is to wrap APIC base register and CR8 operation which can
provide a unique API for user level irqchip and kernel irqchip.
This is a preparation of merging lapic/ioapic patch.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
vmx_load_host_state() bundles fs, gs, ldt, and tss reloading into
one in the hope that it is infrequent. With smp guests, fs reloading is
frequent due to fs being used by threads.
Unbundle the reloads so reduce expensive gs reloads.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Implement emulation of instruction
and al imm8 (opcode 0x24)
and ax/eax imm16/imm32 (opcode 0x25)
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We need to check for signals inside the critical section, otherwise a
signal can be sent which we will not notice. Also move the check
before entry, so that if the signal happens before the first entry,
we exit immediately instead of waiting for something to happen to the
guest.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Split kvm_setup_pio() into two functions, one to setup in/out pio
(kvm_emulate_pio()) and one to setup ins/outs pio (kvm_emulate_pio_string()).
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Both vmx and svm decode the I/O instructions, and both botch the job,
requiring the instruction prefixes to be fetched in order to completely
decode the instruction.
So, if we see a string I/O instruction, use the x86 emulator to decode it,
as it already has all the prefix decoding machinery.
This patch defines ins/outs opcodes in x86_emulate.c and calls
emulate_instruction() from io_interception() (svm.c) and from handle_io()
(vmx.c). It removes all vmx/svm prefix instruction decoders
(get_addr_size(), io_get_override(), io_address(), get_io_count())
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Line 1809 of kvm_main.c is useless, value is overwritten in line 1815:
1809 now = min(count, PAGE_SIZE / size);
1810
1811 if (!down)
1812 in_page = PAGE_SIZE - offset_in_page(address);
1813 else
1814 in_page = offset_in_page(address) + size;
1815 now = min(count, (unsigned long)in_page / size);
1816 if (!now) {
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Remove a duplicated ia32e mode VM Entry control definition and use the
proper one.
Signed-off-by: Xin Li <xin.b.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We use kfree in svm.c and vmx.c, and this works, but it could break at
any time. kfree() is supposed to match up with kmalloc().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
All guest-invokable printks should be ratelimited to prevent malicious
guests from flooding logs. This is a start.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We shouldn't define stat_set on the debug attributes, since that will
cause silent failure on writing: without a set argument, userspace
will get -EACCESS.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
move_msr_up() is used only on X86_64 and generates a warning on !X86_64
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
alloc_vmcs_cpu is already declared (static) above, no need to
redeclare.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
set_msr_interception() is used by svm to set up which MSRs should be
intercepted. It can only fail if someone has changed the code to try
to intercept an MSR without updating the array of ranges.
The return value is ignored anyway: it should just BUG() if it doesn't
work. (A build-time failure would be better, but that's tricky).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
For some reason, mark_page_dirty open-codes __gfn_to_memslot().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
All the physical CPUs on the board should support the same VMX feature
set. Add check_processor_compatibility to kvm_arch_ops for the consistency
check.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_vm_ioctl_get_dirty_log scans bitmap to see it it's all zero, but
doesn't use that information.
Avi says:
Looks like it was used to guard kvm_mmu_slot_remove_write_access();
optimizing the case where the guest just leaves the screen alone (which
it usually does, especially in benchmarks).
I'd rather reinstate that optimization. See
90cb0529dd where the damage was done.
It's pretty simple: if the bitmap is all zero, we don't need to do anything to
clean it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Now we use a kmem cache for allocating vcpus, we can get the 16-byte
alignment required by fxsave & fxrstor instructions, and avoid
manually aligning the buffer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Avi wants the allocations of vcpus centralized again. The easiest way
is to add a "size" arg to kvm_init_arch, and expose the thus-prepared
cache to the modules.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
... in favor of the more general emulator_{read,write}_*.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
... instead of a x86_emulate_ctxt, so that other callers can use it easily.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Changes some svm.c internal function names:
1) io_adress -> io_address (de-germanify the spelling)
2) kvm_reput_irq -> reput_irq (it's not a generic kvm function)
3) kvm_do_inject_irq -> (it's not a generic kvm function)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
container_of is wonderful, but not casting at all is better. This
patch changes svm.c's internal functions to pass "struct vcpu_svm"
instead of "struct kvm_vcpu" and using container_of.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There are several places where hardcoded numbers are used in place of
the easily-available constant, which is poor form.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
container_of is wonderful, but not casting at all is better. This
patch changes vmx.c's internal functions to pass "struct vcpu_vmx"
instead of "struct kvm_vcpu" and using container_of.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Now that kvm generally runs with preemption enabled, we need to protect
the fpu intialization sequence.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows the kvm mmu to perform sleepy operations, such as memory
allocation.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Current kvm disables preemption while the new virtualization registers are
in use. This of course is not very good for latency sensitive workloads (one
use of virtualization is to offload user interface and other latency
insensitive stuff to a container, so that it is easier to analyze the
remaining workload). This patch re-enables preemption for kvm; preemption
is now only disabled when switching the registers in and out, and during
the switch to guest mode and back.
Contains fixes from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add the hypercall number to kvm_run and initialize it. This changes the ABI,
but as this particular ABI was unusable before this no users are affected.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Put cpu feature detecting part in hardware_setup, and stored the vmcs
condition in global variable for further check.
[glommer: fix for some i386-only machines not supporting CR8 load/store
exiting]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch converts the vcpus array in "struct kvm" to a pointer
array, and changes the "vcpu_create" and "vcpu_setup" hooks into one
"vcpu_create" call which does the allocation and initialization of the
vcpu (calling back into the kvm_vcpu_init core helper).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
struct kvm_vcpu has vmx-specific members; remove them to a private structure.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
load_pdptrs can be handed an invalid cr3, and it should not oops.
This can happen because we injected #gp in set_cr3() after we set
vcpu->cr3 to the invalid value, or from kvm_vcpu_ioctl_set_sregs(), or
memory configuration changes after the guest did set_cr3().
We should also copy the pdpte array once, before checking and
assigning, otherwise an SMP guest can potentially alter the values
between the check and the set.
Finally one nitpick: ret = 1 should be done as late as possible: this
allows GCC to check for unset "ret" should the function change in
future.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The writeback fixes (02c03a326a) let
some dead code in the cmpxchg instruction emulation. Remove it.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch mainly imports some constants and rename two exist constants
of vmcs according to IA32 SDM.
It also adds two constants to indicate Lock bit and Enable bit in
MSR_IA32_FEATURE_CONTROL, and replace the hardcode _5_ with these two
bits.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
gfn_to_page might sleep with swap support. Move it out of the kmap calls.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
vmx_cpu_run doesn't handle error correctly and kvm_mmu_reload might
sleep with mutex changes, so I move it above.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Right now, the bug is harmless as we never emulate one-byte 0xb6 or 0xb7.
But things may change.
Noted by the mysterious Gabriel C.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Intel manual (and KVM definition) say the TPR is 4 bits wide. Also fix
CR8_RESEVED_BITS typo.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Creating one's own BITMAP macro seems suboptimal: if we use manual
arithmetic in the one place exposed to userspace, we can use standard
macros elsewhere.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
On this machine (Intel), writing to the CR4 bits 0x00000800 and
0x00001000 cause a GPF. The Intel manual is a little unclear, but
AFIACT they're reserved, too.
Also fix spelling of CR4_RESEVED_BITS.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kernel now has asm/cpu-features.h: use those macros instead of inventing
our own.
Also spell out definition of CR3_RESEVED_BITS, fix spelling and
tighten it for the non-PAE case.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kernel now has asm/cpu-features.h: use those macros instead of
inventing our own.
Also spell out definition of CR0_RESEVED_BITS (no code change) and fix typo.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
I have shied away from touching x86_emulate.c (it could definitely use
some love, but it is forked from the Xen code, and it would be more
productive to cross-merge fixes).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add string pio write support to support some version of Windows.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds a `vcpu_id' field in `struct vcpu', so we can
differentiate BSP and APs without pointer comparison or arithmetic.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
*nopage() in kvm_main.c should only store the type of mmap() fault if
the pointers are not NULL. This patch fixes the problem.
Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Make sure we reset idlecount when we get a good (non-empty) packet.
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Switch to using input-polldev skeleton instead of implementing polling loop
by itself. This also fixes problem with trylock on a mutex in atomic
context.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (119 commits)
[libata] struct pci_dev related cleanups
libata: use ata_exec_internal() for PMP register access
libata: implement ATA_PFLAG_RESETTING
libata: add @timeout to ata_exec_internal[_sg]()
ahci: fix notification handling
ahci: clean up PORT_IRQ_BAD_PMP enabling
ahci: kill leftover from enabling NCQ over PMP
libata: wrap schedule_timeout_uninterruptible() in loop
libata: skip suppress reporting if ATA_EHI_QUIET
libata: clear ehi description after initial host report
pata_jmicron: match vendor and class code only
libata: add ST9160821AS / 3.ALD to NCQ blacklist
pata_acpi: ACPI driver support
libata-core: Expose gtm methods for driver use
libata: add HDT722516DLA380 to NCQ blacklist
libata: blacklist NCQ on Seagate Barracuda ST380817AS
[libata] Turn on ACPI by default
libata_scsi: Fix ATAPI transfer lengths
libata: correct handling of SRST reset sequences
libata: Integrate ACPI-based PATA/SATA hotplug - version 5
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (37 commits)
PCI: merge almost all of pci_32.h and pci_64.h together
PCI: X86: Introduce and enable PCI domain support
PCI: Add 'nodomains' boot option, and pci_domains_supported global
PCI: modify PCI bridge control ISA flag for clarity
PCI: use _CRS for PCI resource allocation
PCI: avoid P2P prefetch window for expansion ROMs
PCI: skip ISA ioresource alignment on some systems
PCI: remove transparent bridge sizing
pci: write file size to inode on proc bus file write
pci: use size stored in proc_dir_entry for proc bus files
pci: implement "pci=noaer"
PCI: fix IDE legacy mode resources
MSI: Use correct data offset for 32-bit MSI in read_msi_msg()
PCI: Fix incorrect argument order to list_add_tail() in PCI dynamic ID code
PCI: i386: Compaq EVO N800c needs PCI bus renumbering
PCI: Remove no longer correct documentation regarding MSI vector assignment
PCI: re-enable onboard sound on "MSI K8T Neo2-FIR"
PCI: quirk_vt82c586_acpi: Omit reading PCI revision ID
PCI: quirk amd_8131_mmrbc: Omit reading pci revision ID
cpqphp: Use PCI_CLASS_REVISION instead of PCI_REVISION_ID for read
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (142 commits)
USB: fix race in autosuspend reschedule
atmel_usba_udc: Keep track of the device status
USB: Nikon D40X unusual_devs entry
USB: serial core should respect driver requirements
USB: documentation for USB power management
USB: skip autosuspended devices during system resume
USB: mutual exclusion for EHCI init and port resets
USB: allow usbstorage to have LUNS greater than 2Tb
USB: Adding support for SHARP WS011SH to ipaq.c
USB: add atmel_usba_udc driver
USB: ohci SSB bus glue
USB: ehci build fixes on au1xxx, ppc-soc
USB: add runtime frame_no quirk for big-endian OHCI
USB: funsoft: Fix termios
USB: visor: termios bits
USB: unusual_devs entry for Nikon DSC D2Xs
USB: re-remove <linux/usb_sl811.h>
USB: move <linux/usb_gadget.h> to <linux/usb/gadget.h>
USB: Export URB statistics for powertop
USB: serial gadget: Disable endpoints on unload
...
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
* 'isdn-cleanups' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
[ISDN] HiSax diva: split setup into three smaller functions
[ISDN] HiSax sedlbauer: move ISAPNP and PCI code into functions of their own
[ISDN] HiSax elsa: split huge setup function into four smaller functions
[ISDN] HiSax avm_pci: split setup into three smaller functions
[ISDN] Remove CONFIG_PCI ifdefs from 100% PCI source code
* Introduce pci_domains_supported global, hardcoded to zero if
!CONFIG_PCI_DOMAINS.
* Introduce 'nodomains' boot option, which clears pci_domains_supported
on platforms that enable it by default (x86, x86-64, and others when
they are converted to use this).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify PCI Bridge Control ISA flag for clarity
This patch changes PCI_BRIDGE_CTL_NO_ISA to PCI_BRIDGE_CTL_ISA
and modifies it's clarifying comment and locations where used.
The change reduces the chance of future confusion since it makes
the set/unset meaning of the bit the same in both the bridge
control register and bridge_ctl field of the pci_bus struct.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid creating P2P prefetch window for expansion ROMs
Because of the future possibility that P2P prefetch windows will contain
address ranges above 4GB some BIOSes are providing space in the P2P
non-prefetch windows for expansion ROMs. This is due to expansion ROM
BAR 32-bit limitation. When expansion ROM BARs without BIOS assigned
address(es) are currently found behind a P2P bridge, the kernel attempts
to create a P2P prefetch window for them even though space for them has
already been provided in the non-prefetch window. _CRS on some systems
with certain resource conservation conscious BIOSes may not provide the
extra 1MB or more memory resource needed for the expansion ROM motivated
prefetch window causing resource allocation errors.
This change corrects the problem by removing IORESOURCE_PREFETCH from
the expansion ROM flags initialization. It also removes
IORESOURCE_CACHEABLE which seems inappropriate if only non-cacheable
memory is available.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Skip ISA ioresource alignment on some systems
To conserve limited PCI i/o resource on some IBM multi-node systems, the
BIOS allocates (via _CRS) and expects the kernel to use addresses in
ranges currently excluded by pcibios_align_resource() [i386/pci/i386.c].
This change allows the kernel to use the currently excluded address
ranges on the IBM x3800, x3850, and x3950.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove transparent bridge sizing.
Due to code in pci_read_bridge_bases() [drivers/pci/probe.c] the child
bus of a transparent bridge already has access to the parent bus
resources so transparent bridge sizing appears unnecessary. The bridge
sizing includes alignment and granularity adjustments that can cause
significantly more memory to be reserved from the parant bus than
required by devices on the child bus and allotted by _CRS.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a /proc/bus/pci file is written to, the size of that PCI device's
configuration space must be written to the inode. Otherwise, it is
possible for the file to specify a size of 0 on stat if a task is holding
the same file open.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On pci_proc_attach_device(), the size of the PCI configuration space is
stored in the proc_dir_entry as the size of the file. Thus, the procfs
interface to PCI devices should use it instead of the device directly.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For cases in which CONFIG_PCIEAER=y (such as distro kernels), allow users
to disable PCIE Advanced Error Reporting by using "pci=noaer" on the
kernel command line.
This can be used to work around hardware or (kernel) software problems.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I got the following error on MIPS Cobalt.
PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@f0000170 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 1 (errno=-16)
pata_via 0000:00:09.1: no available native port
The legacy mode IDE resources set the following order.
pci_setup_device()
Legacy mode ATA controllers have fixed addresses.
IDE resources: 0x1F0-0x1F7, 0x3F6, 0x170-0x177, 0x376
|
V
pcibios_fixup_bus()
MIPS Cobalt PCI bus regions have the -0x10000000 offset from PCI resources.
pcibios_fixup_bus() fix PCI bus regions.
0x1F0 - 0x10000000 = 0xF00001F0
|
V
ata_pci_init_one()
PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1
In some architectures, PCI bus regions have the offset from PCI resources.
For this reason, pci_setup_device() should set PCI bus regions to
dev->resource[].
[akpm@linux-foundation.org: use struct initialiser]
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While reading the MSI code trying to find a reason why MSI wouldn't
work for devices that have a 32-bit MSI address capability, I noticed
that read_msi_msg() seems to read the message data from the wrong
offset in this case.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code for dynamically assigning new ids to PCI drivers,
store_new_id(), calls list_add_tail() with the list head and new node
arguments in reversed order.
The result is that every new id written essentially overwrites the
previous list of ids.
Caught with the help of Rusty's "horribly bad" list_node patch:
http://lkml.org/lkml/2007/6/10/10
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.
This patch sets the korrect register bit to enable the onboard sound.
Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.
New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: Johannes Goecke <goecke@upb.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While PCI_CLASS_REVISION and PCI_REVISION_ID are identical, the
code here discards the revision content and is only interested in
the class number.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Krosten Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert ibmphp to new kthread api
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanups for pciehp_hpc.c. The 80 column rules, removing
unnecessary lines, and so on.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes DBG_ENTER_ROUTIN, DBG_LEAVE_ROUTINE and related
code, which seem no longer needed.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the PCI firmware spec (3.0), the OS must claim control
over the PCI Express Capability bits in addition to the PCI Express
Native Hot Plug feature when executing _OSC.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When removing a device with a bridge on it, only read the
bridge control register if the adapter is actually present.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unnecessary CONFIG_HOTPLUG_PCI_PCIE_EVENT_MODE.
The CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE option is not needed
because polling mechanism can be enabled through 'pciehp_poll_mode'
module option.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1002) fixes a small race which can occur when a driver
expects usbcore to reschedule an autosuspend request. If the request
arrives too late, it won't be rescheduled. The patch adds an extra
argument to autosuspend_check(), indicating that a reschedule is
needed no matter how much time has elapsed.
It also tries to avoid letting asynchronous changes to the value of
jiffies cause a delay to become negative, by caching a local copy of
the current time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Keep track of the device status (as returned by the GET_STATUS
request) and allow it to be manipulated by set_selfpowered() as
well as SET_FEATURE/CLEAR_FEATURE (for remote wakeup)
Implement the wakeup() op, which refuses to do anything if the
DEVICE_REMOTE_WAKEUP feature wasn't set by the host. Now this
driver passes USBCV (at least, with gadget zero).
Fix one more locking bug; lockdep is every developer's friend.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Not surprisingly the Nikon D40X DSC needs the same quirks as the D40,
but it has a separate ID.
See http://bugs.gentoo.org/show_bug.cgi?id=191431
From: Ortwin Glück <odi@odi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as997) fixes a bug in the USB serial core. The core needs
to pay attention to drivers' requirements regarding the number and
type of endpoints a device has.
At the same time, the patch changes the NUM_DONT_CARE constant (which
is stored in a single-byte field) from -1 to a safer, unsigned value.
It also improves the kerneldoc for several fields in the
usb_serial_driver structure.
Finally, the patch replaces a list_for_each() with list_for_each_entry().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
System suspends and hibernation are supposed to be as transparent as
possible. By this reasoning, if a USB device is already autosuspended
before the system sleep begins then it should remain autosuspended
after the system wakes up.
This patch (as1001) adds a skip_sys_resume flag to the usb_device
structure and uses it to avoid waking up devices which were suspended
when a system sleep began.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order. If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused. The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a very small patch (several comment lines) and a one-line
coded change) that allows for USB storage devices that are larger than
2TB.
At the company where I work we need such support, and one of my
co-workers, Jane Liu, pointed out that SCSI low-layer drivers need to
specify what size CDBs they accept. After looking through the code it
became obvious that the current USB Storage code accepted the default of
12-byte CDBs, so I changed it to accept 16-byte CDBs. This allows our
device to work.
Signed-off-by: Richard Sharpe <rsharpe@richardsharpe.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the Atmel USBA UDC which can be found integrated
on AT32AP700x AVR32 processors. For hardware documentation, please see
the AT32AP7000 data sheet:
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
This is a dual speed controller (connects at high or full speed).
The driver supports up to 7 control, bulk, interrupt and isochronous
endpoints with some constraints. Bulk, interrupt and isochronous
transfers are driven by DMA.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds SSB bus glue for the USB OHCI HCD.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup: references to two PM routines (and HCD entry points)
that no longer exist are swapped with their replacements.
Evidently au1xxx and ppc-soc EHCI support doesn't get compiled
with power management very much, or these build bugs would have
been patched long ago.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add OHCI big endian frame_no quirk. The frame_no value stored in the
HCCA is a 16 bit field at a specific offset, but since not all CPUs can
do 16-bit memory accesses it's used as a 32 bit field. And that's why
big-endian OHCI must shift 16 bits ... unless the spec is not followed.
Currently there's one MPC52xx platform that doesn't need the shift. This
patch adds a new "big endian frame_no" quirk to control that at runtime.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Funsoft has a bogus ioctl handler doing bogus termios handling in a bogus
manner. Fortunately we can simply delete all the bogus bits and get the
right default behaviour !
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Visor has a huge complex routine which displays termios bits for debug
but doesn't do anything. Get the correct behaviour by removing it all
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as996) adds an unusual_devs entry for the Nikon DSC D2Xs
camera.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move <linux/usb_gadget.h> to <linux/usb/gadget.h>, reducing
some of the clutter in the main include directory.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
powertop currently tracks interrupts generated by uhci, ehci, and ohci,
but it has no way of telling which USB device to blame USB bus activity on.
This patch exports the number of URBs that are submitted for a given device.
Cat the file 'urbnum' in /sys/bus/usb/devices/.../
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After Serial gadget is being unloaded, neither serial itself, nor other
gadget stuff can be loaded subsequently.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill two unused variables in drivers/usb/misc/sisusbvga/sisusb.c.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a longstanding race in the Ethernet gadget driver, which can cause an
oops on device disconnect. The fix is just to make the TX path check
whether its freelist is empty. That check is otherwise not necessary,
since the queue is always stopped when that list empties (and restarted
when request completion puts an entry back on that freelist).
The race window starts when the network code decides to transmit a packet,
and ends when hard_start_xmit() grabs the freelist lock. When disconnect()
is called inside that window, it shuts down the TX queue and breaks the
otherwise-solid assumption that packets are never sent through a TX queue
that's stopped.
Signed-off-by: Benedikt Spranger <bene@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/misc/sisusbvga/sisusb.c: In function 'sisusb_open':
drivers/usb/misc/sisusbvga/sisusb.c:2444: warning: 'sisusb' is used uninitialized in this function
I can tell that'll oops just by looking at it.
How come this code assume a 7,000 column xterm? :(
Cc: Felipe Balbi <felipe.lima@indt.org.br>
Cc: Thomas <thomas@winischhofer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the problem that accessed register of this controller after
having called iounmap().
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the problem that does not work in the big endian machine.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the problem that does not work in the case of bRequest = 0x05 in
Class or Vendor Request.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes four needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a USB serial port driver for the Winchiphead
CH341 USB-RS232 Converter. This chip also implements an IEEE 1284
parallel port, I2C and SPI, but that is not supported by the driver.
Signed-off-by: Frank A Kingswood <frank@kingswood-consulting.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an error occurs, existing logging uses dbg() so the cause of a
problem is hard to determine. Error conditions shouldn't only be
properly reported with debugging enabled.
A side effect of this change is that when an uninitialised device is
started, a log message similar to the following is sent:
cxacru 5-2:1.0: receive of cm 0x90 failed (-104)
This is normal - the device did not respond so firmware will be loaded.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an additional device ID to the cp2101 USB serial
driver. This device is a Gemalto Prox-PU or CU contactless card reader
(ISO14443-A/B and Mifare). The reader is a standard Gemalto serial
proximity reader using the Gemalto Block Protocol (see reader's
documentation) bundled with a built-in CP2102 for serial/USB
conversion.
Signed-off-by: Edouard Lafargue (edouard@lafargue.name)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upgrade the unusual_devs.h file to support the Nikon D200
Signed-off-by: Mike Pagano <mpagano-kernel@mpagano.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as995) cleans up the remains of the former NO_AUTOSUSPEND
quirk. Since autosuspend is disabled by default, we will let
userspace worry about which devices can safely be suspended. Thus the
lengthy series of quirk entries is no longer needed, and neither is
the quirk ID. I suppose someone might eventually run across a hub
that can't be suspended; let's ignore the possibility for now.
The patch also cleans up the hasty way in which autosuspend gets
disabled. Setting udev->autosuspend_delay to -1 wasn't quite right,
because the value is always supposed to be a multiple of HZ. It's
better to leave the delay value alone and set autosuspend_disabled,
which is what the quirk routine used to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as992) fixes a recently-added bug. During a FREEZE or
PRETHAW suspend notification, non-root devices don't actually get
suspended. So we shouldn't tell their parent hubs that they did.
(This code path used to be skipped over, until the FREEZE/PRETHAW test
got moved out of usb_suspend_both() into generic_suspend().)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as991) updates the unusual_devs entry for the Nokia 6131
phone. As reported by Juan Ignacio Cherrutti, there's new firmware
available but it still has the same old transfer-size limit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (jx001) fixes a variable assignment mistake in hub driver.
limited_power should be set to 0 if the hub is self-powered,and 1 if
the hub is bus-powered.
However, the effect of the code was exactly opposite to the spec's
statement for the Local Power Source field. The spec says, this field
is 1 meaning Local power supply lost while this field is 0 indicating
Local power supply good.(This statement is very confusing.)
So this patch switchs the 0 and 1.
Signed-off-by: Jason Xiao <jidong.xiao@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the error code paths can be enter with buffers to freed buffers.
Serial core would do a kfree() on memory already freed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, every driver under drivers/usb/misc/ also has to be listed in
drivers/usb/Makefile. This has been forgotten more than once, and this
patch changes drivers/usb/Makefile to simply always visit
drivers/usb/misc/ when building the USB code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Toralf Förster <toralf.foerster@gmx.de>
Acked-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This weekend I was hacking around with a trivial USB driver for talking
to the boot load firmware of a USB Bit Whacker. It's running the
MicroChip Pic18 boot loader firmware and I'm putting together a flash
program for writing new FW to the thing.
Anyway in my use of the usb-skeleton.c as my starting point I discovered
my test program was getting hung up after attempting to write a buffer.
The application and driver where hung in a way that required me to
reboot to get it to clean up so I could try again.
It turned out the code path through skel_open can grap the driver's
io_mutex lock and forget to release it.
The following patch fixes the problem for me.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as989) makes usbcore flush all outstanding URBs for each
device as the device is suspended. This will be true even when
CONFIG_USB_SUSPEND is not enabled.
In addition, an extra can_submit flag is added to the usb_device
structure. That flag will be turned off whenever a suspend request
has been received for the device, even if the device isn't actually
suspended because CONFIG_USB_SUSPEND isn't set.
It's no longer necessary to check for the device state being equal to
USB_STATE_SUSPENDED during URB submission; that check can be replaced
by a check of the can_submit flag. This also permits us to remove
some questionable references to the deprecated power.power_state field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as988) breaks usb_hcd_endpoint_disable() apart into two
routines. The first, usb_hcd_flush_endpoint() does the -ESHUTDOWN
unlinking of all URBs in the endpoint's queue and waits for them to
complete. The second, usb_hcd_disable_endpoint() -- renamed for
better grammatical style -- merely calls the HCD's endpoint_disable
method. The changeover is easy because the routine currently has only
one caller.
This separation of function will be exploited in the following patch:
When a device is suspended, the core will be able to cancel all
outstanding URBs for that device while leaving the HCD's
endpoint-related data structures intact for later.
As an added benefit, HCDs no longer need to check for existing URBs in
their endpoint_disable methods. It is now guaranteed that there will
be none.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as987) changes the way FREEZE and PRETHAW suspend events
are handled in usbcore. The decision about whether or not to ignore
them for non-root devices is pushed down into the USB-device driver,
instead of being made in the core code.
This is appropriate, since devices exported to a virtualized guest or
over a network may indeed need to handle these types of suspend, even
though normal devices don't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as990) removes an annoying debugging message. Nobody
really cares when endpoint pseudo-devices are released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/misc/sisusbvga/sisusb.c: In function sisusb_open
drivers/usb/misc/sisusbvga/sisusb.c:2444: warning: sisusb is used uninitialized in this function
is a genuine bug (which will cause oops). We cannot use "sisusb" in
error path for (!interface), because sisusb will itself be derived
from "interface" later.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the iuu_phoenix driver submits another URB from a completion handler.
This dictates a certain order of calls to usb_kill_urb() in kill_traffic().
As other drivers may do it the other way round, we need to use both
orders in kill_traffic().
This patch does so and should be merged before iuu_phoenix is merged.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ELAN U132 Host Controller Driver uses the semaphore sw_lock as
mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as984) fixes a rather elementary mistake in dummy_hcd.
The new statement label should come before the spin_unlock_irqrestore,
not after it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as981) removes the remaining nontrivial usages of
urb->status from usbcore.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that urb->status isn't used, urb->lock doesn't protect anything.
This patch (as980) removes it and replaces it with a private mutex in
the one remaining place it was still used: usb_kill_urb.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator. Now the field
doesn't get set until just before the URB's completion routine is
called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as978) reorganizes the way usbmon uses urb->status. It
now accepts the status value as an argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as977) reorganizes the way r8a66597-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Parts of this patch were written by Yoshihiro Shimoda.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as976) reorganizes the way sl811-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
The patch also improves the handling of faults during the status stage
of a control transfer, since it no longer needs to retain the error
information from the earlier stages.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as975) reorganizes the way ohci-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as974) reorganizes the way ehci-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
The patch also simplifies the handling of -EREMOTEIO, since the only
use of that code is to set the do_status flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as973) reorganizes the way dummy-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the BenQ Mobile Phone EF81 to pl2303
Signed-off-by: Andreas Loibl <andreas@andreas-loibl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/usb/serial/oti6858.c::pl2303_buf_alloc() the return value
of kmalloc() is being cast to "struct pl2303_buf *", but that need
not be done here since kmalloc() returns "void *".
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some usb-serial devices (e.g. certain Edgeport models) have more than
one serial port on the same USB device/interface.
Currently the only way to distinguish these ports in userspace is by
their minor device number: the driver makes them consecutive and in
stable order.
However, for the purpose of stable naming with udev this is
insufficient: when udev handles the ADD event for one of the ports it
doesn't know what minor number the other one has.
To make stable naming easier, export the port number via sysfs.
Signed-off-by: Roman Kagan <rkagan@sw.ru>
Signed-off-by: Dmitry Guryanov <dimak@dgap.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as983) makes a test for minimum-length command sizes in
g_file_storage less restrictive. It doesn't matter because commands
with bad lengths will be detected later on anyway, and doing it like
this makes the driver interoperable with certain buggy hosts such as
the JVC HiFi (reported by Samuel Hangouet).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No hardware but this driver is currently totally broken so we can't make
it much worse. Remove all tbe broken invalid termios handling and replace
it with a proper set_termios method.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as972) changes ohci-hcd so that after an error occurs, the
remaining TDs for the URB will be skipped over entirely instead of
going through the donelist. This enables the driver to give back the
URB as soon as the error is detected, avoiding the need to store the
error status in urb->status.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as971) fixes a small mistake: The URB's completion status
needs to be adjusted before the URB is passed to usmon_urb_complete(),
not afterward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Handle the FT232RL device type in exactly the same way as FT232BM
devices (FT232RL detection was added around kernel 2.6.20 but not code
for handling it).
Signed-off-by: Andrew M. Bishop <amb@gedanken.demon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more. To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses. The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.
By moving the work out of the HCDs, this removes a fair amount of
repeated code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (968) changes the way uhci-hcd reports status for
Isochronous URBs. Until now urb->status has been set to the last
detected error code. But other HCDs don't do this; they leave the
status set to 0 and report errors only in the individual iso packet
descriptors. So this patch removes the extra computation and makes
uhci-hcd behave like the others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as967) makes a few relatively minor changes to the
r8a66597 driver:
finish_request() does nothing but call done(), so merge the
two routines.
Detect and report -EOVERFLOW errors.
Fix the calculation that checks for short packets.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is not necessary to powerdown the ports on ehci_pci_reinit() when the
chip reset already did that. Removing this saves 20ms during restart
after poweroff paths (which OLPC uses a lot).
To ensure driver startup then behaves consistently, force a reset during
driver startup. (Not doing this was an accident of some previous changes
to the init sequence.)
Make the corresponding change in the PS3 support. It's not clear what
ehci-fsl should do here; it has similar code to the PS3.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <rvinson@mvista.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update copyrights and remove not necessary warning (ueagle-atm works
well on suspend/resume).
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not sleep in kernel thread when device is disconnected, this make faster
suspending and module unloading. Use one wait queue for sleeping.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ueagle-atm driver load DSP firmware in function, which is running from
common workqueue. In some (error) circumstances loading firmware may
sleep for long periods (even 60 seconds, depending on timeout). This
block keyboard driver, which also use common workqueue. To fix problem
use custom workqueue in ueagle-atm.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let's user control how much USB bus bandwidth will be reserved by
ueagle-atm device. This make possible to share bus with other devices
when ueagle-atm driver works in isochronous mode.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for Devolo and Elsa chipsets. These chipsets have no information
about ADSL annex (line type) encoded in USB descriptors. Driver try to
get this information from USB VID and PID or it can be explicitly set by
the user through module parameter. Thanks to Johann Hanne, whose make
most of this patch.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support to newest chipset of eagle family. It is compatible with
older chipsets at USB level. However DSP firmware and CMVs
(Configuration and Management Variables) have different format of data
and are sent/received by different way.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as962) cleans up some code I forgot to remove earlier in
the isp116x and sl811 HCDs. There is no longer any need to check for
unlink-during-submit; it can't happen since the endpoint queues are
now under the protection of the HCD-private spinlock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we'd have already oops'ed if one of
these was NULL.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make Pete happy
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
