Scan need to be delayed only after association to allow EAPOL
exchange. We don't need the delay for IBSS mode.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the system is misconfigured with CONFIG_RFKILL set but CONFIG_RFKILL_INPUT
not set, the built-in radio LEDs will not work. In the current code, no warning
is issued.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SIOCSIWSCAN handler is passed data in an iw_point structure. Some
drivers erronously use an iw_param instead.
On 32 bit architectures the difference isn't noticed as the flags
parameter tends to be the only one used by scan handlers and is at the
same offset.
On 64 bit architectures the pointer in the iw_point structure means the
flag parameter is at different offsets in these structures.
Thanks to Jean Tourrilhes for tracking this down for orinoco, and Pavel
Roskin for confirming the fix and identifying other suspect handlers.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/libertas/wext.o
drivers/net/wireless/libertas/wext.c: In function ‘lbs_get_rts’:
drivers/net/wireless/libertas/wext.c:307: warning: comparison is always
false due to limited range of data type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use min_t to avoid warnings when the typesafe version is used.
Explicitly cast u64s to unsigned long long when being passed to printk.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This paves the way for dynamic radio additions while the module
is loaded. Also restrict the number of radios to 100 because
creating that many already takes forever.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WPA requires that the PTK is installed immediately after the 4-way handshake
in order to properly decrypt the subsequent incoming EAPOL-GTK frame. If the
PTK is not enabled by the time the EAPOL-GTK frame arrives, the frame is
dropped and the supplicant does not receive the group key.
This will happen with fast Access Points that send the EAPOL-GTK frame before
the suplicant has successfully installed and enabled the PTK. To mitigate
this situation, this patch simplifies and accelerates the SIOCSIWENCODEEXT
execution.
This patch resolves OLPC ticket 7825 (http://dev.laptop.org/ticket/7825)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the initialization of QoS parameters.
Reported-by: Lorenzo Nava, Francesco Gringoli
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds MODULE_FIRMWARE statement for 3945 HW.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds MODULE_FIRMWARE statement for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates PCI IDs for 5350 Wifi/WiMax.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no need, at worst ieee80211_start_tx_ba_session
will log a message when debugging is enabled, and poking such
internals of mac80211 definitely doesn't belong into an RC
algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control algorithms may need access to a station's
HT capabilities, so share the ht_info struct in the
public station API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_info->txrate_idx member isn't used by all RC algorithms
in the way it was intended to be used, move it into those that
require it (only PID) and keep track in the core code of which
rate was last used for reporting to userspace and the mesh MLME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As more preparation for a saner rate control algorithm API,
share the supported rates bitmap in the public API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable in sta_info is only used in a meaningful way
by the Intel RC algorithms, so move it into those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In analogy with the previous patch to make mac80211-hwsim
verify that the virtual interface pointers are correct,
this makes it very that it knows about all station structs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211-hwsim is a debugging tool for mac80211, and as such
it can very well verify that mac80211 isn't passing junk to
drivers, especially the vif pointer is prone to this because
for vlan interfaces the AP interface pointer needs to be passed.
This makes mac80211-hwsim add a magic cookie to the private vif
area and verify it whenever an operation is called that gets a
vif pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And support setting both long and short retries independently.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RF kill support is enabled when CONFIG_RFKILL
is set.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the functions in main.c are re-ordered in such
a way that all local functions are defined before mac80211
and pci callbacks.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic reset command is unused. Each interface type needs to
handle the reset command differently since after reset, the firmware is
dead and interface-specific mechanisms must be used to reinitialize the
card.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up zd1211rw's own regulatory work, and makes use of
the new cfg80211 regulatory_hint().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwconfig txpower can now be used to set tx power to fixed or auto. If set to
auto the default firmware settings are used.
The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams
noted the command was no longer supported in firmware V9+.
Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for 3 antennas for Legacy, SISO and MIMO2.
MIMO3 is still not supported yet.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in Rate Scaling. When moving from SISO to MIMO we
need to choose the lowest higher rate, instead of choosing the highest in MIMO.
No doing this can lead to a high packet loss in the highest rate in MIMO,
leading not to move MIMO although lower in MIMO could give a better TPT.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If certain commands were in-flight when the card was pulled or the
driver rmmod-ed, cleanup would block on the work queue stopping, but the
work queue was in turn blocked on the current command being canceled,
which didn't happen. Fix that.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There isn't really a good reason to have the LED
configuration options selectable per driver, lets
make it default 'y' and make it depend on the
NEW_LEDS and LEDS_CLASS interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFKILL should be enabled for _all_ hardware whether
or not they feature a rfkill button or not.
Remove driver specific RFKILL configuration options
and make the rt2x00lib version depend on CONFIG_RFKILL
and defaulting to 'y' to make sure it will always
be enabled when RFKILL was enabled.
This also fixes some bugs where RFKILL wasn't initialized
and didn't respond to RFKILL key presses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts:
b93ce437eb
rt2x00: Fix the beacon length bug
The workaround is no longer required since it has been
correctly fixed in rt2x00usb now.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes in the specifications have improved the performance
of the BCM4306/2 devices that use b43legacy as the driver. These
"errors" in the specs have been present from the very first implementation
of bcm43xx.
Signed-off-by: Ehud Gavron <gavron@wetwork.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A coding error present since b43legacy was incorporated into the
kernel has prevented the driver from using the rate-setting mechanism
of mac80211. The driver has been forced to remain at a 1 Mb/s rate.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.26], [2.6.25]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need the workqueue anymore, as we can now sleep in the callback.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It causes compile errors on m68k and it is not needed.
Remove it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the initialization of the default QoS parameters.
This got broken by "wireless: fix warnings from QoS patch".
Reported-by: Lorenzo Nava
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch brings the 5GHz Phy in any prism54 devices (of course, only those who have one) to life.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I hope this patch is enough to cover at least the basic requirements of IEEE 802.11h's TPC.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware can provide lots of useful statistics about noise floor,
mac time and lots of numbers about successful transfers and dropped
frames.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new filters settings to make the card more useful in monitor mode.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tcpdump:
02:15:42.874518 61112184us tsft 48.0 Mb/s 2437 MHz (0x0480) antenna 1 [0x0000000e] CF +QoS Data IV
02:15:42.874557 >>>4356079526us<<< tsft 24.0 Mb/s 2437 MHz (0x0480) antenna 1 [0x0000000e] Acknowledgment
02:15:42.976844 61214513us tsft 1.0 Mb/s 2437 MHz (0x0480) antenna 0 [0x0000000e] Beacon
as one can see on the huge jump, it's very plausible that firmware does not report the
full 64-bit mac time, just the lower 32bit and some kinds of flags...
Therefore if we want a useful timestamp we have to emulate the high bits.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes compile warning for ‘iwl4965_hw_channel_switch’ defined
but not used.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwlwifi by removing uneeded declarations and removing
uneeded symbol export reducing the namespace pollution. It also fixes some
typos in comments.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes usage of the results from disconnected antenna alg to
know how many antennas are connected.
It also synchronizes between the chain noise alg and the W/A that
disables power management during association. All the antennas must be
enables during the chain noise algorithm. Hence, power management is
restored only after the completion of the algorithm.
In the future, we will need to update the AP that we don't support MIMO
if there is only one antenna connected. We also need to update the rate
scaling algorithm.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl_priv.ps_mode for clearer
iwl_priv.current_ht_config.sm_ps (spatial multiplexing power save).
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch follows 11n spec naming more rigorously replacing MIMO_PS
with SM_PS (Spatial Multiplexing Power Save).
(Originally submitted as 4 patches, "mac80211: change MIMO_PS to SM_PS",
"iwlwifi: change MIMO_PS to SM_PS", "ath9k: change MIMO_PS to SM_PS",
and "iwlwifi: remove double definition of SM PS". -- JWL)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
