In order to sort out our struct termios and add proper speed control we need
to separate the kernel and user termios structures. Glibc is fine but the
other libraries rely on the kernel exported struct termios and we need to
extend this without breaking the ABI/API
To do so we add a struct ktermios which is the kernel view of a termios
structure and overlaps the struct termios with extra fields on the end for
now. (That limitation will go away in later patches). Some platforms (eg
alpha) planned ahead and thus use the same struct for both, others did not.
This just adds the structures but does not use them, it seems a sensible
splitting point for bisect if there are compile failures (not that I expect
them)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Virtual memmap support for s390. Inspired by the ia64 implementation.
Unlike ia64 we need a mechanism which allows us to dynamically attach
shared memory regions.
These memory regions are accessed via the dcss device driver. dcss
implements the 'direct_access' operation, which requires struct pages
for every single shared page.
Therefore this implementation provides an interface to attach/detach
shared memory:
int add_shared_memory(unsigned long start, unsigned long size);
int remove_shared_memory(unsigned long start, unsigned long size);
The purpose of the add_shared_memory function is to add the given
memory range to the 1:1 mapping and to make sure that the
corresponding range in the vmemmap is backed with physical pages.
It also initialises the new struct pages.
remove_shared_memory in turn only invalidates the page table
entries in the 1:1 mapping. The page tables and the memory used for
struct pages in the vmemmap are currently not freed. They will be
reused when the next segment will be attached.
Given that the maximum size of a shared memory region is 2GB and
in addition all regions must reside below 2GB this is not too much of
a restriction, but there is room for improvement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is now possible to enable/disable ERP related logging without re-compile
and re-ipl. A additional sysfs-attribute 'erplog' allows to switch the
logging non-interruptive.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the contents of the userspace asm/setup.h header consistent on all
architectures:
- export setup.h to userspace on all architectures
- export only COMMAND_LINE_SIZE to userspace
- frv: move COMMAND_LINE_SIZE from param.h
- i386: remove duplicate COMMAND_LINE_SIZE from param.h
- arm:
- export ATAGs to userspace
- change u8/u16/u32 to __u8/__u16/__u32
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last thing we agreed on was to remove the macros entirely for 2.6.19,
on all architectures. Unfortunately, I think nobody actually _did_ that,
so they are still there.
[akpm@osdl.org: x86_64 fix]
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Schafer <gschafer@zip.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_LBD and CONFIG_LSF are spread into asm/types.h for no particularly
good reason.
Centralising the definition in linux/types.h means that arch maintainers
don't need to bother adding it, as well as fixing the problem with
x86-64 users being asked to make a decision that has absolutely no
effect.
The H8/300 porters seem particularly confused since I'm not aware of any
microcontrollers that need to support 2TB filesystems.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
VMALLOC_END on 31bit should be 0x8000000UL instead of 0x7fffffffL.
The page mask which is used to make sure memory_end is on 4MB/2MB
boundary is wrong and not needed. Therefore remove it.
Make sure a vmalloc area does also exist and work on (future)
machines with 4TB and more memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using memcmp to compare ccw_dev_id implies that the whole structure (incl.
padding) has always been completely initialized to sane values. Comparing
the structures field by field doesn't make such assumptions.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Need this at yet another file and don't want to add yet another
extern...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of reipl cpcmd gets called when all other cpus are not running
anymore. To prevent deadlocks change __cpcmd so that it doesn't take
any locks and call cpcmd or __cpcmd, whatever is correct in the current
context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KEXEC_CONTROL_MEMORY_LIMIT is an unsigned long value and therefore
should be defined as one. Otherwise the kexec control page can be
allocated above 2GB which will cause a specification exception on the
sam31 instruction in the s390 kexec relocation code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of our own user_termio_to_kernel_termios() and
kernel_termios_to_user_termio() macros which didn't check for errors
on user space accesses. Instead use the generic functions which
handle this properly.
In addition the generic version of user_termio_to_kernel_termios()
also copies the c_line member which was missing in our variant.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Follow other architectures and add __must_check to uaccess functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* sanitize prototypes, annotate
* kill useless shifts
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add arch specific dev_archdata to struct device
Adds an arch specific struct dev_arch to struct device. This enables
architecture to add specific fields to every device in the system, like
DMA operation pointers, NUMA node ID, firmware specific data, etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@suse.de>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
handle_pte_fault uses pte_present, pte_none and pte_file to find out
the type of a pte. That is done without holding the page table lock.
This clashes with the way how ptep_clear_flush removes active page
table entries from the system. First the ipte instruction is used
to invalidate the pte and remove all plt entries for the page. The
ipte sets the hardware invalid bit without changing any other bit.
After the ipte finished the pte is cleared. A concurrent fault can
observe the the previously valid pte with the invalid bit set. With
the current encoding of the different pte types an invalidated
read-only pte can be misinterpreted as a swap-pte.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the proper structures to identify device and subchannel. Change
get_disc_ccwdev_by_devno() to get_disc_ccwdev_by_dev_id().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the last few places where a pointer to pt_regs gets passed.
Also make sure we call set_irq_regs() before irq_enter() and after
irq_exit(). This doesn't fix anything but makes sure s390 looks the
same like all other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Use CONFIG_GENERIC_TIME and define TOD clock source.
[PATCH] sysrq: irq change build fix.
[S390] irq change build fixes.
[S390] cio: 0 is a valid chpid.
[S390] monwriter buffer limit.
[S390] ap bus poll thread priority.
Trivial typo fix in the "syntax error if percpu macros are incorrectly
used" patch. I misspelled "identifier" in all places. D'Oh!
Thanks to Dirk Mueller to point this out.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The include of linux/smp.h needs to be done before the #if that
checks for the compiler version. Seems like fallout from the
inline assembly cleanup patch vs. the directed yield patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The last in-kernel user of errno is gone, so we should remove the definition
and everything referring to it. This also removes the now-unused lib/execve.c
file that was introduced earlier.
Also remove every trace of __KERNEL_SYSCALLS__ that still remained in the
kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the regs_return_value() macro to extract the return value in an
architecture agnostic manner, given the pt_regs.
Other architecture maintainers may want to add similar helpers.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new diagnose 0x9c in the spinlock implementation for s390. It
yields the remaining timeslice of the virtual cpu that tries to acquire a
lock to the virtual cpu that is the current holder of the lock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On systems running with virtual cpus there is optimization potential in
regard to spinlocks and rw-locks. If the virtual cpu that has taken a lock
is known to a cpu that wants to acquire the same lock it is beneficial to
yield the timeslice of the virtual cpu in favour of the cpu that has the
lock (directed yield).
With CONFIG_PREEMPT="n" this can be implemented by the architecture without
common code changes. Powerpc already does this.
With CONFIG_PREEMPT="y" the lock loops are coded with _raw_spin_trylock,
_raw_read_trylock and _raw_write_trylock in kernel/spinlock.c. If the lock
could not be taken cpu_relax is called. A directed yield is not possible
because cpu_relax doesn't know anything about the lock. To be able to
yield the lock in favour of the current lock holder variants of cpu_relax
for spinlocks and rw-locks are needed. The new _raw_spin_relax,
_raw_read_relax and _raw_write_relax primitives differ from cpu_relax
insofar that they have an argument: a pointer to the lock structure.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
touch_nmi_watchdog() calls touch_softlockup_watchdog() on both
architectures that implement it (i386 and x86_64). On other architectures
it does nothing at all. touch_nmi_watchdog() should imply
touch_softlockup_watchdog() on all architectures. Suggested by Andi Kleen.
[heiko.carstens@de.ibm.com: s390 fix]
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Cc: Andi Kleen <ak@muc.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert s390 page handling macros to functions. In particular this fixes a
problem with s390's SetPageUptodate macro which uses its input parameter
twice which again can cause subtle bugs.
[akpm@osdl.org: build fix]
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The clocksource infrastructure introduced with commit
ad596171ed broke 31 bit s390.
The reason is that the do_div() primitive for 31 bit always
had a restriction: it could only divide an unsigned 64 bit
integer by an unsigned 31 bit integer. The clocksource code
now uses do_div() with a base value that has the most
significant bit set. The result is that clock->cycle_interval
has a funny value which causes the linux time to jump around
like mad.
The solution is "obvious": implement a proper __div64_32
function for 31 bit s390.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Consistently use MAX_ERRNO when checking for errors in __syscall_return().
[ralf@linux-mips.org: build fix]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the changes necessary for shared page tables is to standardize the
pxx_page macros. pte_page and pmd_page have always returned the struct
page associated with their entry, while pte_page_kernel and pmd_page_kernel
have returned the kernel virtual address. pud_page and pgd_page, on the
other hand, return the kernel virtual address.
Shared page tables needs pud_page and pgd_page to return the actual page
structures. There are very few actual users of these functions, so it is
simple to standardize their usage.
Since this is basic cleanup, I am submitting these changes as a standalone
patch. Per Hugh Dickins' comments about it, I am also changing the
pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning.
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce ARCH_LOW_ADDRESS_LIMIT which can be set per architecture to
override the 4GB default limit used by the bootmem allocater within
__alloc_bootmem_low() and __alloc_bootmem_low_node(). E.g. s390 needs a
2GB limit instead of 4GB.
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_var()/per_cpu()/__get_cpu_var() arguments must be simple
identifiers. Otherwise the arch dependent implementations might break.
This patch enforces the correct usage of the macros by producing a syntax
error if the variable is not a simple identifier.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/~dwmw2/hdroneline:
[HEADERS] One line per header in Kbuild files to reduce conflicts
Manual (trivial) conflict resolution in include/asm-s390/Kbuild
This introduces new user-copy operations which are optimized for
copying more than 256 Bytes on new hardware.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduces a struct uaccess_ops which allows setting user-copy
operations at run-time.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changed and simplified some page table related #defines and code.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch delivers a new Linux API in the form of a misc char
device that is useable from user space and allows write access
to the z/VM APPLDATA Monitor Records collected by the *MONITOR
System Service of z/VM.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce asm header that contains the appldata data structures and
the diag inline assembly.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert GET_IPL_DEVICE assembler macro to C function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use do { } while (0) constructs instead of empty defines to avoid
subtle compile bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is now possible to specify a ccw/fcp dump device which is used to
automatically create a system dump in case of a kernel panic. The dump
device can be configured under /sys/firmware/dump.
In addition it is now possible to specify a ccw/fcp device which is used
for the next reboot of Linux. The reipl device can be configured under
/sys/firmware/reipl.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move initrd if the bitmap of the bootmem allocator would overwrite it.
In addition this patch sets the default size and address of the initrd to 0.
Therefore all boot loaders must set the initrd size and address correctly.
This is especially relevant for ftp boot via HMC/SE, where this change
requires a special patch file entry in the .ins file which sets these two
values contained at address 0x10408 and 0x10410.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Grundy <grundym@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow the user space to send extended cprb messages directly to the
PCIXCC / CEX2C cards. This allows the CCA library to construct special
crypto requests that use "secure" keys that are stored on the card.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The user space interface of the zcrypt device driver implements the old
user space interface as defined by the old z90crypt driver. Everything
is there, the /dev/z90crypt misc character device, all the lovely ioctls
and the /proc file. Even writing to the z90crypt proc file to configure
the crypto device still works. It stands to reason to remove the proc
write function someday since a much cleaner configuration via the sysfs
is now available.
The ap bus device drivers register crypto cards to the zcrypt user
space interface. The request router of the user space interface
picks one of the registered cards based on the predicted latency
for the request and calls the driver via a callback found in the
zcrypt_ops of the device. The request router only knows which
operations the card can do and the minimum / maximum number of bits
a request can have.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The z90crypt driver has served its term. It is replaced by the shiny
new zcrypt device driver.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On Tue, 2006-09-12 at 17:44 +0100, David Woodhouse wrote:
> asm-s390/debug.h requires linux/string.h, which does not exist
> asm-s390/elf.h requires asm/system.h, which does not exist
Move things around slightly so the right things end up within
#ifdef __KERNEL__ and thus don't pollute the exported headers.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add missing volatile to the get_clock / get_cycles inline assemblies
to avoid that consecutive calls get optimized away.
Signed-off-by: Andreas Krebbel <krebbel1@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
set_wmb should not be used in the kernel because it just confuses the
code more and has no benefit. Since it is not currently used in the
kernel this patch removes it so that new code does not include it.
All archs define set_wmb(var, value) to do { var = value; wmb(); }
while(0) except ia64 and sparc which use a mb() instead. But this is
still moot since it is not used anyway.
Hasn't been tested on any archs but x86 and x86_64 (and only compiled
tested)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
futex_atomic_cmpxchg_inatomic has the same bug as the other
atomic futex operations: the operation needs to be done in the
user address space, not the kernel address space. Add the missing
sacf 256 & sacf 0.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure that raw_local_save_flags and raw_local_irq_restore always get an
unsigned long parameter. raw_irqs_disabled should call raw_local_save_flags
instead of local_save_flags.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__builtin_trap() has the archictecture defined backend in gcc since gcc 3.3.
To make sure the kernel builds with gcc 3.2 as well, use the old style BUG()
statement if compiled with older gcc versions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the lock validator framework to prove rwsem locking correctness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
irqtrace support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the per_cpu_offset() generic method. (used by the lock validator)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NOTE: ZVC are *not* the lightweight event counters. ZVCs are reliable whereas
event counters do not need to be.
Zone based VM statistics are necessary to be able to determine what the state
of memory in one zone is. In a NUMA system this can be helpful for local
reclaim and other memory optimizations that may be able to shift VM load in
order to get more balanced memory use.
It is also useful to know how the computing load affects the memory
allocations on various zones. This patchset allows the retrieval of that data
from userspace.
The patchset introduces a framework for counters that is a cross between the
existing page_stats --which are simply global counters split per cpu-- and the
approach of deferred incremental updates implemented for nr_pagecache.
Small per cpu 8 bit counters are added to struct zone. If the counter exceeds
certain thresholds then the counters are accumulated in an array of
atomic_long in the zone and in a global array that sums up all zone values.
The small 8 bit counters are next to the per cpu page pointers and so they
will be in high in the cpu cache when pages are allocated and freed.
Access to VM counter information for a zone and for the whole machine is then
possible by simply indexing an array (Thanks to Nick Piggin for pointing out
that approach). The access to the total number of pages of various types does
no longer require the summing up of all per cpu counters.
Benefits of this patchset right now:
- Ability for UP and SMP configuration to determine how memory
is balanced between the DMA, NORMAL and HIGHMEM zones.
- loops over all processors are avoided in writeback and
reclaim paths. We can avoid caching the writeback information
because the needed information is directly accessible.
- Special handling for nr_pagecache removed.
- zone_reclaim_interval vanishes since VM stats can now determine
when it is worth to do local reclaim.
- Fast inline per node page state determination.
- Accurate counters in /sys/devices/system/node/node*/meminfo. Current
counters are counting simply which processor allocated a page somewhere
and guestimate based on that. So the counters were not useful to show
the actual distribution of page use on a specific zone.
- The swap_prefetch patch requires per node statistics in order to
figure out when processors of a node can prefetch. This patch provides
some of the needed numbers.
- Detailed VM counters available in more /proc and /sys status files.
References to earlier discussions:
V1 http://marc.theaimsgroup.com/?l=linux-kernel&m=113511649910826&w=2
V2 http://marc.theaimsgroup.com/?l=linux-kernel&m=114980851924230&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115014697910351&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767318740&w=2
Performance tests with AIM7 did not show any regressions. Seems to be a tad
faster even. Tested on ia64/NUMA. Builds fine on i386, SMP / UP. Includes
fixes for s390/arm/uml arch code.
This patch:
Move counter code from page_alloc.c/page-flags.h to vmstat.c/h.
Create vmstat.c/vmstat.h by separating the counter code and the proc
functions.
Move the vm_stat_text array before zoneinfo_show.
[akpm@osdl.org: s390 build fix]
[akpm@osdl.org: HOTPLUG_CPU build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements an API whereby an application can determine the
label of its peer's Unix datagram sockets via the auxiliary data mechanism of
recvmsg.
Patch purpose:
This patch enables a security-aware application to retrieve the
security context of the peer of a Unix datagram socket. The application
can then use this security context to determine the security context for
processing on behalf of the peer who sent the packet.
Patch design and implementation:
The design and implementation is very similar to the UDP case for INET
sockets. Basically we build upon the existing Unix domain socket API for
retrieving user credentials. Linux offers the API for obtaining user
credentials via ancillary messages (i.e., out of band/control messages
that are bundled together with a normal message). To retrieve the security
context, the application first indicates to the kernel such desire by
setting the SO_PASSSEC option via getsockopt. Then the application
retrieves the security context using the auxiliary data mechanism.
An example server application for Unix datagram socket should look like this:
toggle = 1;
toggle_len = sizeof(toggle);
setsockopt(sockfd, SOL_SOCKET, SO_PASSSEC, &toggle, &toggle_len);
recvmsg(sockfd, &msg_hdr, 0);
if (msg_hdr.msg_controllen > sizeof(struct cmsghdr)) {
cmsg_hdr = CMSG_FIRSTHDR(&msg_hdr);
if (cmsg_hdr->cmsg_len <= CMSG_LEN(sizeof(scontext)) &&
cmsg_hdr->cmsg_level == SOL_SOCKET &&
cmsg_hdr->cmsg_type == SCM_SECURITY) {
memcpy(&scontext, CMSG_DATA(cmsg_hdr), sizeof(scontext));
}
}
sock_setsockopt is enhanced with a new socket option SOCK_PASSSEC to allow
a server socket to receive security context of the peer.
Testing:
We have tested the patch by setting up Unix datagram client and server
applications. We verified that the server can retrieve the security context
using the auxiliary data mechanism of recvmsg.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Acked-by: Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes for several channel measurement facility bugs:
* Blocks copied from the hardware might not be consistent. Solve this
by moving the copying into idle state and repeating the copying.
* avg_sample_interval changed with every read, even though no new block
was available. Solve this by storing a timestamp when the last new
block was received.
* Several locking issues.
* Measurements were not reenabled after a disconnected device became
available again.
* Remove #defines for ioctls that were never implemented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for parallel-access-volumes to the dasd driver. This
allows concurrent access to dasd devices with multiple channel
programs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The preempt_count in the thread_info structure must be initialized to 1.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix __syscall_return macro: valid error numbers are in the range
of -1..-4095.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changes in the DASD driver require an asynchronous implementation of the
subchannel reprobe loop. This loop was so far only used by the blacklisting
mechanism but is now available to all CCW device drivers.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Encapsulate complete bitops.h with #ifdef __KERNEL__ and remove the now
superfluous ALIGN_CS define and its users.
This patch is needed for compiling klibc.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are several instances of per_cpu(foo, raw_smp_processor_id()), which
is semantically equivalent to __get_cpu_var(foo) but without the warning
that smp_processor_id() can give if CONFIG_DEBUG_PREEMPT is enabled. For
those architectures with optimized per-cpu implementations, namely ia64,
powerpc, s390, sparc64 and x86_64, per_cpu() turns into more and slower
code than __get_cpu_var(), so it would be preferable to use __get_cpu_var
on those platforms.
This defines a __raw_get_cpu_var(x) macro which turns into per_cpu(x,
raw_smp_processor_id()) on architectures that use the generic per-cpu
implementation, and turns into __get_cpu_var(x) on the architectures that
have an optimized per-cpu implementation.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct the return type of handle_IRQ_event() (inconsistency noticed during
Xen development), and remove redundant declarations. The return type
adjustment required breaking out the definition of irqreturn_t into a
separate header, in order to satisfy current include order dependencies.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It also adds all the related quad routines.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
[S390] __FD_foo definitions.
Switch to __s32 types in joystick.h instead of C99 types for consistency.
Add <sys/types.h> to headers included for userspace in <linux/input.h>
Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
Remove struct fddi_statistics from user view in <linux/if_fddi.h>
Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
Use __uXX types in <linux/divert.h> for struct divert_blk et al.
Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
Use __uXX types in user-visible structures in <linux/nbd.h>
Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
Use __uXX types for S390 DASD volume label definitions which are user-visible
S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
Fix private integer types used in V4L2 ioctls.
...
Manually resolve conflict in include/linux/mtd/physmap.h
Make the definitions of __FD_SET, __FD_CLR and __FD_ISSET independent
from asm/bitops.h and remove the macro magic that tests for __GLIBC__.
Use simple C inline functions instead of set_bit, clear_bit and test_bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
From: Martin Schwidefsky <schwidefsky@de.ibm.com>
__futex_atomic_op needs to do an atomic operation in the user address space,
not the kernel address space. Add the missing sacf 256/sacf 0 to switch to
the secondary mode before doing the compare-and-swap. In addition add
another fixup for catch specification exceptions if the compare-and-swap
address is not aligned.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
The path grouping can fail due to non-unique pathgroup-IDs. The source for
the CPU-ID part of the ID was incorrectly specified on 64 bit systems.
Additionally, the length of the ID was too large due to incorrect data packing
declaration. Fix CPU-ID lowcore address and add missing packing declaration.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new vmsplice system call and add missing __NR_xxx defines for
sys_set_robust_list, sys_get_robust_list, sys_splice, sys_sync_file_range
and sys_tee.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also remove Bob Burroughs' email address, since it's no longer valid.
Acked-by: Eric D Rossman <edrossma@us.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
These aren't needed by glibc or klibc, and they're broken in some cases
anyway. The uClibc folks are apparently switching over to stop using
them too (now that we agreed that they should be dropped, at least).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add a read_mostly section and define __read_mostly to prevent cache line
pollution due to writes for mostly read variables. In addition fix the
incorrect alignment of the cache_line_aligned data section. s390 has a
cacheline size of 256 bytes.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for atomic futex operations.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
