This patch adds new PCI serial card support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for SIIG 8-port boards. These boards have 4 ports in
separate bars and another 4 ports in the single bar. Because of this strange
port arrangement these cards need special setup function. Fortunately no other
SIIG cards have more than 4 port, so this setup function could be used for them
too.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a new device which is look like:
Serial controller: Decision Computer International Co. PCCOM2 (rev 02) (prog-if 02 [16550])
0700: 6666:0004 (rev 02) (prog-if 02)
Flags: medium devsel, IRQ 177
Memory at fe000000 (32-bit, non-prefetchable) [size=128]
I/O ports at e880 [size=128]
I/O ports at e400 [size=256]
It has two 16550A, and is not listed in kernel, although the
manufacturer clams that it is supported...
I've created the following patch, it only add the new PCI id and the
card to the repository, it seems to work.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've also fixed the sort-ordering comments on this naming convention.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch marks a few serial data structures const, moving them to
.rodata where they won't false-share cachelines with things that get
written to.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the MRi PCIDS1 dual port serial card. This card is a
little controversial since it is the subject of a PCI vendor/device ID
clash. (See
http://www.ussg.iu.edu/hypermail/linux/kernel/0303.1/0516.html). I have
for now just used the hex ID 0x950a. The divisor was part calculated part
iterated, so may not be exactly correct (but works for me at all settings
between 300 - 115300 bps).
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert parport_serial to use the new 8250_pci interface, converting
the table to a pciserial_board table. This also unuses the SPCI_*
definitions in serialP.h, which can now be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-jig the setup/removal/suspend/resume of 8250 pci ports so that they
know slightly less about how they're attached to a PCI device. Expose
this as the new interface for registering PCI serial ports, as well as
the pciserial_board structure and associated flag definitions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass the serial_private structure via the setup method instead of
the pci_dev. We don't want to assume that the pci_dev's driver
data is a pointer to serial_private. Instead, put the pci_dev
inside serial_private.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Collapse all the SIIG quirk entries into one. SIIG10x cards all
have PCI device IDs of 0x10xx, SIIG20x cards all have PCI device
IDs of 0x20xx.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for SIIG Quartet Serial card. This card has Oxford
Semiconducor 16954 quad UART which is clocked by 10x faster
(18.432 MHz) quartz.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
