This patch implements pinmux tables for the sh7785 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch improves the support for gpio pins that are hard wired
to either input or output and lack control register association.
A special force enum id is used to allow use without control
register but still mark the gpio pin as input or output.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use a slower VIO_CKO clock frequency for the ov772x on Migo-R.
This improves the camera picture quality on Panel Board V2.1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the pinmux code to use the boolean value for
the function gpio_set_value(). Without this patch values other
than 0 and 1 will result in incorrect GPIO settings.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the ov772x byte sequence to enable byte swap. This to reflect
the recent CEU driver change to follow incoming byte order.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 3f5a54e371 ("ftrace: dump out ftrace
buffers to console on panic") added an ftrace buffer dumper that hooks
in to the die notifier chain and dumps out data in the oops path.
Unfortunately SH supported ftrace but didn't support DIE_OOPS, so add
that in and get it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the generic remove_memory() provided by mm/memory_hotplug.c instead.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7203.h include paths were missed in the previous update, so switch
the include path to cpu/ as with the rest.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
but also by the code which is not inside CONFIG_PROC_VMCORE. For
example, is_kdump_kernel() is used by powerpc code to determine if
kernel is booting after a panic then use previous kernel's TCE table.
So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
able to correctly determine that we are booting after a panic and setup
calgary iommu accordingly.
o So remove the assumption that elfcorehdr_addr is under
CONFIG_PROC_VMCORE.
o Move definition of elfcorehdr_addr to arch dependent crash files.
(Unfortunately crash dump does not have an arch independent file
otherwise that would have been the best place).
o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
second kernel without KEXEC being enabled.
o I don't see sh setup code parsing the command line for
elfcorehdr_addr. I am wondering how does vmcore interface work on sh.
Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
broken on sh.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pinmux management is tied in to this code, while it is presently only
used by platforms that select GENERIC_GPIO. The asm/gpio.h definitions
are not referenced when GENERIC_GPIO is disabled, resulting in a build
failure for all of the platforms that don't select it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove left overs from the generic declared coherent rework.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve Migo-R ethernet performance by reducing smc91x overruns.
This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_file() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Renesas AP325RXA board has Epson RX-8564LC of RTC.
This patch supports RTC of this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch hooks up the magicpanelr2 board with the sh7720 pinmux code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7720 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the rsk7203 board use the newly added sh7203 pinmux code.
Only a single LED plus the serial console pins for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7203 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on AP325RXA and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
While at it 2 LEDs and one switch are added and exported to user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7723 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7722 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds gpio code together with the pinmux table parser.
In the future we should optimize this and switch back to gpiolib.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were doing largely bogus things and using the wrong typing for
the address. Bring these in line with the ARM definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AP320 and AP325RXA has CPLD data in NOR Flash.
If this area erased, this board can not boot.
This patch create CPLD data area and set writeable mask bit.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for ftrace to SH. This only includes CONFIG_FTRACE,
and does not handle dynamic ftrace presently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a few trace points across events that are deemed
interesting. This implements a number of trace points:
- The page fault handler / TLB miss
- IPC calls
- Kernel thread creation
The original LTTng patch had the slow-path instrumented, which
fails to account for the vast majority of events. In general
placing this in the fast-path is not a huge performance hit, as
we don't take page faults for kernel addresses.
The other bits of interest are some of the other trap handlers, as
well as the syscall entry/exit (which is better off being handled
through the tracehook API). Most of the other trap handlers are corner
cases where alternate means of notification exist, so there is little
value in placing extra trace points in these locations.
Based on top of the points provided both by the LTTng instrumentation
patch as well as the patch shipping in the ST-Linux tree, albeit in a
stripped down form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are other places where we want to have access to the trap/exception
number, so move out the lookup_exception_vector() helper. While we're at
it, refactor it slightly to return the vector instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is 256K instead of 1M.
[ Converted to use asm/sizes.h. -- PFM ]
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the powerpc commit f6a616800e
'[POWERPC] Fix kernel stack allocation alignment'.
SH has traditionally forced the thread order to be relative to the page
size, so there were never any situations where the same bug was
triggered by slub. Regardless, the usage of > 8kB stacks for the larger
page sizes is overkill, so we switch to using slab allocations there,
as per the powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This combination triggers a divide by zero in kernel/fork.c when
calculating the initial max_threads value:
max_threads = mempages / (8 * THREAD_SIZE / PAGE_SIZE);
Simply disable 4K stacks on 64kB PAGE_SIZE to work around this,
as it's not a terribly useful combination to begin with.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
HAVE_IOREMAP_PROT enables an unconditional reference to
generic_access_phys(), which remains undefined in the nommu case.
As there's no point in supporting this there anyways, simply fix
up the dependency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
linux/mmzone.h isn't exported, kill it off from asm/setup.h and simply
deal with it in the places that have a dependency instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These have been using overrides for ELF_CORE_COPY_TASK_REGS and
ELF_CORE_COPY_FPREGS while the generic versions can be used instead.
Presently the pt_regs are also duplicated across elf_core_copy_regs()
and elf_core_copy_task_regs(), this switches to simply copying out
through elf_core_copy_regs() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the support requirements are out of the way, finally
enable support for tracehook.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a defconfig for the R2D+ target in the qemu system emulator.
Eventually it will be possible to simply use the r2d+ defconfig as it is.
Provided by Shin-ichiro KAWASAKI.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All CPUs must have a sensible cpu_clk definition these days, which we can
safely use for deriving the preset loops_per_jiffy. The only odd one out
is SH-5, which hasn't been hammered in to the framework yet.
Based on the ST patch.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is doing a force_sig() SIGTRAP, which is already taken
care of in the generic code if no one asserts NOTIFY_STOP. Switch the
default return to NOTIFY_DONE in the case of unhandled traps, so that
the same trap may pass through to other users on the same die chain.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all parts support trapa #0xff, so use something within the debug trap
range that's accessible on all parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was initially checked in with a stupid default of y, while most
everyone is going to want to have this disabled anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Renesas (RTE) EDOSK7760 board. Currently
supported devices are:
- ramdisk support
- ethernet support
- nfs support
- ext2/ext3 support
- i2c support
- fb support (M)
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This uses jump_to_uncached() which is now given the noinline attribute
due to the special section mapping. Kill off the inline attribute to
fix up compilation failure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initial support for kprobes/kretprobes for 32-bit SH platforms.
[ General cleanup and some rework for the kretprobe hash lock. -- PFM ]
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Because alloc_bootmem functions return the allocated memory always
zeroed, an additional call of memset on allocated memory is
unnecessary.
Signed-off-by: Marek Skuczynski <M.Skuczynski@adbglobal.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the TMU code to allow NO_HZ to work on sh
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH4 to convert a subnormal double
into a float by catching the FPE and implementing the FCNVDS
instruction in software.
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a problems with the set up of Linux memory:
- When reserving memory at boot time, the code previously reserved
the bottom page of memory, and then from one page up to the end of
the bootmap. This had the desired effect, but was strictly speaking
wrong, as the one page was actually whatever CONFIG_ZERO_PAGE_OFFSET
had been set to.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix "make uImage" load and entry addresses in 32-bit mode.
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a problem in the code which copies the vmalloc portion of the
kernel's page table into the current user space page table. The addition
of the four level page table code breaks on folded page tables, because
the pud level is always present (although folded). This updates the code
to use the same style of updates for the pud as is used for the pgd
level.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
statically initialise the cached_to_uncached offset, so that we can use
it immediatly.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixes up compile errors with missing timer definitions. It's pointless to
have this enabled anyways if CONFIG_SMP=n.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The dummy timer needs to be registered on the boot CPU before the
system timer clockevent is registered, or broadcasting doesn't work
as advertized.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks up GENERIC_CLOCKEVENTS_BROADCAST and a dummy local timer,
which we call in to from the timer IPI when no other local timer is
provided.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a generic smp_message_recv() routine (based on the PPC
one), that IPI IRQs can wrap in to.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a problem within the SH implementation of resume_kernel code,
that implements in assembly the bulk of preempt_schedule_irq function without
taking care of the extra code needed to handle the BKL preemptible.
The patch basically consists of removing this asm code and calling the common
C implementation (see kernel/sched.c) as other archs do.
Another change is the missing 'cli' macro invocation at the beginning of
the resume_kernel.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fix the problem that cannot work semtimedop system call.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the AP325RXA defconfig to include the recently merged
uio_pdrv_genirq driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the MigoR defconfig to include the recently merged
uio_pdrv_genirq driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch kills a section mismatch for platform_resource_setup_memory().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The crash kernel entry point is currently checked by the kexec kernel
code and only physical addresses in the reserved memory window are
accepted. This means that we can't pass P2 or P1 addresses as entry
points in the case of crash kernels. This patch makes sure we can start
crash kernels by adding support for physical address entry points.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The reserved crash kernel memory range is currently missing from
/proc/iomem. crashk_res is mistakenly setup after __add_active_range().
Reorder things to make sure the resource shows up in /proc/iomem.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following compile error caused by
commit c459dbf294
(sh: ptrace single stepping cleanups.):
<-- snip -->
...
CC arch/sh/kernel/ptrace_64.o
arch/sh/kernel/ptrace_64.c: In function 'user_disable_single_step':
arch/sh/kernel/ptrace_64.c:134: error: 'regs' undeclared (first use in this function)
arch/sh/kernel/ptrace_64.c:134: error: (Each undeclared identifier is reported only once
arch/sh/kernel/ptrace_64.c:134: error: for each function it appears in.)
...
make[2]: *** [arch/sh/kernel/ptrace_64.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 42fd3b142d
(sh: Initial consolidation of the _32/_64 uaccess split.)
mistakenly removed the sh64 __strnlen_user() prototype,
resulting in the following compile error:
<-- snip -->
...
CC init/main.o
In file included from include/linux/poll.h:13,
from include/linux/rtc.h:113,
from include/linux/efi.h:19,
from init/main.c:43:
arch/sh/include/asm/uaccess.h: In function 'strnlen_user':
arch/sh/include/asm/uaccess.h:213: error: implicit declaration of function '__strnlen_user'
...
make[2]: *** [init/main.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE, because control
page is used for not only code on some platform. For example in kexec
jump, it is used for data and stack too.
[akpm@linux-foundation.org: unbreak powerpc and arm, finish conversion]
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SH needs this in order to make sure that r4 has a sane value at process
entry time, which the libc expects has already been taken care of.
Fixes random crashes in flat binaries.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the LCD panel size for sh_mobile_lcdc boards. This allows us
to perform dpi and screen aspect ratio calculations in user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow user to pass parameters on kernel command line to override
default size for physically contiguous memory buffers. The default
VPU buffer size is too small for VGA harware encoding, but instead
of just bumping up the number we allow the user to override the
default size using the command line. Supports SuperH Mobile hardware
blocks such as VEU, VPU and CEU.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export sh7723 VEU hardware blocks as VEU2H. The sh7723 VEU2H differs
a bit from the sh7722 VEU so use different names for our UIO devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove MSTPCR register definitions from Migo-R header file. The clock
frame work should be used instead of direct register access.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has sh_eth device. This patch add sh_eth platform device
to this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we oops in mm/hugetlb.c:1325, which is the order == 0 test in
hugetlb_add_hstate() called at initialization time. So, disable 64kB
huge pages when we're using a 64kB PAGE_SIZE. On most parts this will
force the default to be 1MB huge pages.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
rsk7203_defconfig fails to build with the following error:
<-- snip -->
...
LD .tmp_vmlinux1
arch/sh/kernel/built-in.o:(__ksymtab+0xb8): undefined reference to `__udivsi3_i4i'
arch/sh/kernel/built-in.o:(__ksymtab+0xc8): undefined reference to `__sdivsi3_i4i'
make[1]: *** [.tmp_vmlinux1] Error 1
<-- snip -->
That worked with 2.6.26, and these are far less undefined references
than in the cases where libgcc was missing.
[ These symbols are not defined on SH-2 versions of libgcc, so we have to
special case the export there. - Paul ]
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patches compile errors like the following caused by
commit 51f3547d61
(sh: Allow SH-3 and SH-5 to use common headers):
<-- snip -->
...
CC arch/sh/mm/init.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/init.c: In function 'mem_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/init.c:232: error: implicit declaration of function 'p3_cache_init'
make[2]: *** [arch/sh/mm/init.o] Error 1
make[1]: *** [arch/sh/mm] Error 2
...
CC kernel/fork.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/fork.c: In function 'dup_mmap':
/home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/fork.c:323: error: implicit declaration of function 'flush_dcache_mmap_lock'
/home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/fork.c:325: error: implicit declaration of function 'flush_dcache_mmap_unlock'
make[2]: *** [kernel/fork.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support SH7619 Internal ethernet controler.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch remove unneeded #include <linux/ide.h>'s.
It also adds a required #include <linux/interrupt.h> that was previously
implicitely pulled by ide.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
[bart: revert change to tests/lkdtm.c (spotted by Stephen Rothwell)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Newfile: arch/sh/include/cpu-sh2a/cpu/addrspace.h
This file seems had be removed to use fallback (cpu-common/cpu/addrspace.h),
but, I'd like to add sh2a specific file here, because
1. the values defined there are not suitable for sh2a.
2. I don't think there is "common" definition for these values.
Values are chosen by consideration of followings...
P1 is 0. perhaps no question.
P2 is from hardware manual, which says no-cache area starts at 20000000.
It means that P? space size=20000000.
P3 is P2+size since asm/ptrace.h uses P3 as a end of P2.
P4 is P3+size since asm/fixup.h uses P4 as a end of P3.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH never really supported a.out, so this was all just copied over blindly
from x86 way back when. As we don't reference linux/a.out.h anywhere in
the tree, these can now safely be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We haven't called in to __do_IRQ() in a long time, so it seems like a
reasonable time to switch this on by default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the NUMA node data isn't saved on kexec. This implements a
simple arch_crash_save_vmcoreinfo() for saving off the relevant data.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-X2 extended mode TLB allows for toggling of the exec bit, so make
sure we are using the right protection bits for module space there
also.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Removed duplicated include <linux/irq.h> in
arch/sh/boards/mach-se/7343/irq.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Removed duplicated include <linux/delay.h> in
arch/sh/boards/board-ap325rxa.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following build error was caused by an obvious typo:
<-- snip -->
...
LD arch/sh/mm/built-in.o
make[2]: *** No rule to make target `arch/sh/boards/board-shmin..o', needed by `arch/sh/boards/built-in.o'. Stop.
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit f15cbe6f1a
(sh: migrate to arch/sh/include/) moved KBUILD_CFLAGS
(which is used by LIBGCC) below LIBGCC, causing build
errors like the following:
<-- snip -->
...
LD .tmp_vmlinux1
arch/sh/kernel/built-in.o: In function `module_clk_recalc':
clock-sh4.c:(.text+0x80f0): undefined reference to `__udivsi3_i4i'
...
make[1]: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This ended up causing build breakage on O= builds, as reported by Adrian:
<-- snip -->
...
CC init/main.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/irq.h:4,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/irq.h:23,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/hardirq.h:5,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/hardirq.h:7,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/asm-generic/local.h:5,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/local.h:4,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/module.h:19,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/init/main.c:13:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/machvec.h:15:27:
error: asm/machtypes.h: No such file or directory
make[2]: *** [init/main.o] Error 1
<-- snip -->
So we simply move machtypes.h back to its original place. asm-offsets.h is
still generated there regardless, until such a time that we find a better place
to stash auto-generated files.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this was always being set to AUDIT_ARCH_SH, which assumes
big endian. Fix this up so that the architecture actually reflects
what we're running on.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the changes in commits:
7d6d637dac4f72c4279e
on powerpc. Adding in TIF_NOTIFY_RESUME, and cleaning up the syscall
tracing to be more generic. This is an incremental step to turning
on tracehook, as well as unifying more of the ptrace and signal code
across the 32/64 split.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the single stepping done by sh/sh64 ptrace implementations
to use the generic user_enable/disable_single_step(), and subsequently
rips out a lot of ptrace request cases that are now handled generically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A quick cut and paste from other architectures to allow SH
to parse the elfcorehdr command line argument which is required
for both is_kdump_kernel() and vmcore to function.
(the former is as yet unused on SH).
Tested compilation only
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
Presently this is protected by a CONFIG_VSYSCALL ifdef so we don't
inadvertently trigger the creation of the gate VMA on CPUs where we don't
enable the vDSO, which is obviously not visible to userspace. Fix this up
by adding in an ifndef __KERNEL__ check at the same time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix recently introduced I2C build breakage on AP325RXA and Migo-R.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This flattens out the board directories in to individual mach groups,
we will use this for getting rid of unneeded directories, simplifying
the build system, and becoming more coherent with the refactored
arch/sh/include topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I compiled Solution Engine, this become compile error
because plaform device of sh_eth device becomes enable.
When sh7710/sh7712 which could use sh_eth was chosen,
revised it so that platform device of sh_eth device became enable.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the workaround in 2b4b2bb421
and cleans up __put_user_asm() to get the sizing right from the onset.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
