This patch adds support for the following saa7134 xc3028 based boards:
132 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
133 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
134 -> Avermedia M115 [1461:a836]
135 -> Compro VideoMate T750 [185b:c900]
This is based on a original patch thanks to Markus Rechberger that added xc3028
gpio init code for the above boards.
This patch moves saa7134_tuner_callback to saa7134-cards, originally used only
by tda8290 DVB-S boards. The callback was made more generic to support other
tuners.
Currently, it supports both tda8290 and xc2028/xc3028 tuners. Added also the
basis for xc5000 tuner callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only tm6000 needs to be aware when a frequency is being changed. This seems
to improve channel change detection. Other bridges don't need this.
So, better to discard any errors if this fails, and proceed changing the
channels.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It seems that on this board, the demodulator provides the pullup on the I2C
bus, which means that calling i2c_gate_ctrl crashes the bus. Turn this off
and the xc3028 can talk OK. Also fix some GPIO related settings that
became more clear through working on this.
Some changes made by Mauro Chehab to allow merging it with some
other xc3028 patches.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for tuning DVB-T channels on DViCO's FusionHDTV DVB-T Pro board.
The IR remote and analog tuner are not supported at this time.
Some changes made by Mauro Chehab to allow merging it with some other xc3028
patches.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ports a patch from Markus Rechberger to work with tuner-xc2028.
It adds entries for several cx88 boards with xc2038/3028 tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
load ir-kbd-i2c for IR remote control support on DViCO FusionHDTV 5 PCI nano
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC is known to work.
SVideo / Composite should work (I have no cable to test).
Analog tuner support does not work.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch addresses most issues pointed out by Russell and Erik, moves
recently introduced into pxa-regs.h camera-specific defines into
pxa_camera.c, removes dummy power-management functions, improves
function-naming, etc.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only advertise pixel formats, that we actually can support in the
present configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Received written ack from the dabusb author
that the firmware is BSD licensed.
As bonus clarify copyright holder.
Signed-off-by: maximilian attems <max@stro.at>
Acked-by: Deti Fliegl <deti@fliegl.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The DMA timeout timer was started once for each set of DMA transfers,
but it should be started for each single DMA transfer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CROPCAP suggests that video capture supports cropping, but this is not the
case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The existing yuv code limits output to the display area occupied by the
framebuffer. This patch allows the yuv output to be 'detached' via
V4L2_FBUF_FLAG_OVERLAY.
By default, the yuv output window will be restricted to the framebuffer
dimensions and the output position is relative to the top left corner of the
framebuffer. This matches the behaviour of previous versions.
If V4L2_FBUF_FLAG_OVERLAY is cleared, the yuv output will no longer be linked
to the framebuffer. The maximum dimensions are either 720x576 or 720x480
depending on the current broadcast standard, with the output position
relative to the top left corner of the display. The framebuffer itself can be
resized, moved and panned without affecting the yuv output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The i2c driver code was once added for the out-of-tree ivtv driver,
but the ivtv driver hasn't used that for a long time so this code can
now be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the needlessly global stk_camera_{suspend,resume}()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf-dma-sg does not need to depend on PCI. Switch it to using generic
DMA API, convert all affected drivers, relax Kconfig restriction, improve
compile-time type checking, fix some Coding Style violations while at it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
simple_set_tv() creates a buffer with 4 elements, and calls
simple_std_setup(), passing &buffer[1]. This makes the 5th element of buffer to
be initialized to 0, overriding some area outside the buffer.
Also, simple_std_setup() receives a buffer as parameter, but the buffer is
just overriden after the call, so, it doesn't make much sense to pass it as a
parameter.
This patch removes buffer[] from the function call, creating, instead, a local
var to be used internally.
Thanks to Axel Rometsch <axel.rometsch@freenet.de> for pointing the issue.
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The I2C bus interface of the LNB supply sits behind the i2c gate of the
tda10086, so wrappers were necessary for the set_voltage functions.
For the time being, the board will show up as MD8800
Many thanks to Hermann Pitton for his help
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support is not complete yet and untested.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The chip can control 2 LNBs independently.
The driver distinguishes them by evaluating the MSB of the override_set
parameter of the isl6405_attach function.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Both camera drivers can function without GPIO support, in which case they
will only support the 10 bit data width mode. But the two respective switch
have to depend on CONFIG_GENERIC_GPIO. Additionally remove redundant
gpio_is_valid tests - they are repeated in bus_switch_request() functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Upon suggestion by David Brownell use a gpio_is_valid() predicate
instead of an explicit NO_GPIO macro. The respective patch to
include/asm-generic/gpio.h has been accepted upstream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
combine tda18271c1_tune and tda18271c2_tune into a single function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move rf calibration code from tda18271c1_tune into a new function,
tda18271c1_rf_tracking_filter_calibration
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Continue to support the V4L2_CID_PRIVATE_BASE + 1 control in the ABI
- Report the same control as V4L2_CID_SHARPNESS
- Report the private control disabled via QUERYCTRL
Signed-off-by: Brandon Philips <bphilips@suse.de>
Acked-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf-dma-sg.c should be converted to the generic DMA API to make it
also useful for non-PCI configurations. Even now it can be used thanks
to compatibility macros in include/asm-generic/pci-dma-compat.h. This
has been verified to work on PXA270 CPU with the pxa_camera.c soc-camera
driver. For this the following temporary work-around is needed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some dvb demodulators access the tuner directly without using i2c.
In these cases, i2c_adap may be NULL. This patch fixes
hybrid_tuner_request_state to allow for NULL i2c_adapters.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds two new fourcc codes (as per info at fourcc.org)
for 16bpp mono and 16bpp Bayer formats.
Signed-off-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a driver for the Quick Capture Interface on the PXA270.
It is based on the original driver from Intel, but has been re-worked
multiple times since then, now it also supports the V4L2 API. This patch
depends on a complementary patch, submitted to the ARM tree, providing
PXA270 camera platform bindings.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver provides an interface between platform-specific camera
busses and camera devices. It should be used if the camera is connected
not over a "proper" bus like PCI or USB, but over a special bus, like,
for example, the Quick Capture interface on PXA270 SoCs. Later it should
also be used for i.MX31 SoCs from Freescale. It can handle multiple
cameras and / or multiple busses, which can be used, e.g., in
stereo-vision applications.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add V4L2_IDENT chip IDs for mt9m001 and mt9v022 cameras, will be used by
future patches, primarily to implement the g_chip_ident ioctl.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add all of the recently proposed camera class controls. These controls
should appear in the next version of the v4l2spec.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes should appear in the next update of the v4l2spec.
HCENTER and VCENTER are unused in the tree so I added a _DEPRECATED
postfix so applications can remove their use.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Assign the number of instances remaining as the return value of
hybrid_tuner_release_state, in case there is any extra cleanup that
the tuner driver needs to do after an instance has been destroyed.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert tda18271 to use the new hybrid_tuner_request_state and
hybrid_tuner_release_state macros to manage state sharing between
hybrid tuner instances.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Store a pointer to the device name in the name field of
struct tuner_i2c_props, so that we can remove the
printk macros defined in tuner-i2c.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create a macro implementing a standard method to share state amongst
multiple instances of a hybrid tuner object.
Also, prepare tuner_foo printk macros for the removal of PREFIX
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I'd prefer to leave this here, but official CodingStyle
doesn't care what I think :-/
Remove the emacs format override block to comply with Kernel CodingStyle.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
