User-space sometimes needs this information. In particular, the GPRS
context or the AT commands pipe setups may use the pipe handle as a
reference.
This removes the settable pipe handle with CONFIG_PHONET_PIPECTRLR.
It did not handle error cases correctly. Furthermore, the kernel
*could* implement a smart scheme for allocating handles (if ever
needed), but userspace really cannot.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves most of the accept logic to process context like other
socket stacks do. Then we can use a few more common socket helpers
and simplify a bit.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of the pipe controller, there is now quite a bit
of repetitive code for small signaling messages. Lets factor it.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the Phonet pipe backlog callbacks returned negative
errno instead of NET_RX_* values.
In other cases, NET_RX_DROP was returned for invalid packets, even
though it seems only intended for buffering problems (not for
deliberately discarded packets).
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phonet assumes that packets are never dropped. We try our best to
avoid this situation. But lets return ENOBUFS if queueing to the
network device fails so that the caller knows things went wrong.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous Phonet patch series introduced per-socket implicit
destination (i.e. connect()). In that case, the destination
socket address is NULL in the transmit function.
However commit a8059512b1
("Phonet: implement per-socket destination/peer address")
is incomplete and would trigger a NULL dereference.
(Fortunately, the code is not in released kernel, and in fact
currently not reachable.)
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If modifications on other cpus are ok, then modifications to
the tree during lookup done by the local cpu are ok too.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6060 uses either the lower 16 or upper 16 mii addresses,
depending on the value of the EE_CLK/ADDR4 pin. Support both
configurations by using the sw_addr setting as base address.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to use cfg->fc_scope not the final nh_scope value.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing output route lookups, we have to select the source address
if the user has not specified an explicit one.
First, if the route has an explicit preferred source address
specified, then we use that.
Otherwise we search the route's outgoing interface for a suitable
address.
This search can be precomputed and cached at route insertion time.
The only missing part is that we have to refresh this precomputed
value any time addresses are added or removed from the interface, and
this is accomplished by fib_update_nh_saddrs().
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new target ddp offload support ndo_fcoe_ddp_target().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ip6_mc_source(), ip6_mc_msfilter() as well as ip6_mc_msfget() declare
and assign dev but do not use the variable afterwards.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was there before, I forgot about this. Allows deliveries to
ptype_base handlers registered for orig_dev. I presume this is still
desired.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_semantic_match() requires that if the type doesn't signal an
automatic error, it must be of type RTN_UNICAST, RTN_LOCAL,
RTN_BROADCAST, RTN_ANYCAST, or RTN_MULTICAST.
Checking this every route lookup is pointless work.
Instead validate it during route insertion, via fib_create_info().
Also, there was nothing making sure the type value was less than
RTN_MAX, so add that missing check while we're here.
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to associate a net_device with another net_device which
already exists, batman-adv assumes that this interface is a fully
initialized batman mesh interface without checking it. The behaviour
when accessing data behind netdev_priv of a random net_device is
undefined and potentially dangerous.
Reported-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Batman-adv works with "hard interfaces" as well as "soft interfaces".
The new name should better make clear which kind of interfaces this
list stores.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When printing the soft interface table the number of entries in the
softif neigh list are first being counted and a fitting buffer
allocated. After that the softif neigh list gets locked again and
the buffer printed - which has the following two issues:
For one thing, the softif neigh list might have grown when reacquiring
the rcu lock, which results in writing outside of the allocated buffer.
Furthermore 31 Bytes are not enough for printing an entry with a vid
of more than 2 digits.
The manual buffering is unnecessary, we can safely print to the seq
directly during the rcu_read_lock().
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When unicast_send_skb() is increasing the orig_node's refcount another
thread might have been freeing this orig_node already. We need to
increase the refcount in the rcu read lock protected area to avoid that.
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->curr_gw need to be used, as well as spin/rcu locking.
Otherwise we might end up using a curr_gw pointer pointing to already
freed memory.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Batman-adv could receive several payload broadcasts at the same time
that would trigger access to the broadcast seqno sliding window to
determine whether this is a new broadcast or not. If these incoming
broadcasts are accessing the sliding window simultaneously it could
be left in an inconsistent state. Therefore it is necessary to make
sure this access is atomic.
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
bonding / alternating candidates need to be secured by rcu locks
as well. This patch therefore converts the bonding list
from a plain pointer list to a rcu securable lists and references
the bonding candidates.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
hardif_disable_interface() calls purge_orig_ref() to immediately free
all neighbors associated with the interface that is going down.
purge_orig_neighbors() checked if the interface status is IF_INACTIVE
which is set to IF_NOT_IN_USE shortly before calling purge_orig_ref().
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
rt->rt_iif is only ever inspected on input routes, for example DCCP
uses this to populate a route lookup flow key when generating replies
to another packet.
Therefore, setting it to anything other than zero on output routes
makes no sense.
Signed-off-by: David S. Miller <davem@davemloft.net>
