EQ is getting armed wrongly in INTx mode as INTx interrupt is taking
some time to deassert. This can cause another interrupt while NAPI is
scheduled and scheduling a NAPI in interrupt does not take effect.
This causes interrupt to be missed and traffic stalls. Fixing this by
preventing wrong arming of EQ.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer does not support DDR self test. Fix ethtool self test by
skipping this test for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase time given by driver to adapter for completing FW download
to 30 seconds. Also return correct status when FW download times out.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN and multicast hardware filters are limited and can get
exhausted in adapters with many PCI functions. If setting
a VLAN or multicast filter fails due to lack of sufficient
hardware resources, these packets get dropped. Fix this by
switching to VLAN or multicast promiscous mode so that these
packets are not dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool get settings was not displaying all the settings correctly.
use the get_phy_info to get more information about the PHY to fix this.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flex10 mode the number of vlan slots supported is halved.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will prevent double free in some cases where be_clear() is called
for cleanup when be_setup() fails half-way.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of be_close(), instead of waiting for a max of 200ms for each TXQ,
wait for a total of 200ms for completions from all TXQs to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery involves ring cleanup and re-creation. The worker
thread must not run during EEH cleanup/resume.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: Fixed up the bad typecasting pointed out by David...
In the current design 8 TXQs are serviced by 1 EQ, while each RSS queue
is serviced by a separate EQ. This is being changed as follows:
- Upto 8 EQs will be used (based on the availabilty of msix vectors).
Each EQ will handle 1 RSS and 1 TX ring. The default non-RSS RX queue and
MCC queue are handled by the last EQ.
- On cards which provide support, upto 8 RSS rings will be used, instead
of the current limit of 4.
The new design allows spreading the TX multi-queue completion processing
across multiple CPUs unlike the previous design.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs use get mac list command to get their mac address. The format of
this command has changed. Update driver to use the new format.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version number in query link status command is getting overwritten in
be_wrb_cmd_hdr_prepare() routine. Move the initialization to fix this
issue. Also initialize the domain field.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameters for ETHTOOL_FLASHDEV include a filename, which ought to
be null-terminated. Currently the only driver that implements
ethtool_ops::flash_device attempts to add a null terminator if
necessary, but does it wrongly. Do it in the ethtool core instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also rename a few counters appropritely and delete 2 counters that are not
implemented in HW.
vlan_mismatch_drops does not exist in BE3 and is accounted for in
address_mismatch_drops. Do the same thing for BE2 and Lancer.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation of 64 bytes in skb headroom is not enough if we have to pull
ethernet + ipv6 + tcp headers, and/or extra tunneling header.
Its currently not noticed because netdev_alloc_skb_ip_align(64) give us
more room, thanks to power-of-two kmalloc() roundups.
Make sure we ask for 128 bytes so that side effects of upcoming patches
from Ian Campbell dont decrease benet rx performance, because of extra
skb head reallocations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Vasundhara Volam <vasundhara.volam@emulex.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RSS rings are not created in a multi-channel config.
RSS rings can be created on one (out of four) interfaces per port in a
multi-channel config. Doing this insulates the driver from a FW bug wherin
multi-channel config is wrongly reported even when not enabled. This also
helps performance in a multi-channel config, as one interface per port gets
RSS rings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More drivers where net_device_ops should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) fix be_vlan_add/rem_vid to return proper status
2) perform appropriate housekeeping if firmware command succeeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer does not have HW registers to indicate the EQ causing the INTx
interrupt. As a result EQE entries of one EQ may be consumed when interrupt
is caused by another EQ. Fix this by arming CQs at the end of NAPI poll
routine to regenerate the EQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use adapter->num_vfs (and not the module param) to store the actual
number of vfs created. Use the same variable to reflect SRIOV
enable/disable state. So, drop the adapter->sriov_enabled field.
- use for_all_vfs() macro in VF configuration code
- drop the "vf_" prefix for the fields of be_vf_cfg; the prefix is
redundant and removing it helps reduce line wrap
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool "-g" option is supposed to report the max queue length and
user modified queue length for RX and TX queues. be2net doesn't support
user modification of queue lengths. So, the correct values for these
would be the max numbers.
be2net incorrectly reports the queue used values for these fields.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable Tx vlan offloading in certain cases.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
update pmem_fifo_overflow_drop, rx_priority_pause_frames counters.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When non power of two MSIX vectors are given to driver, some RX queues
are not utilized. Program RSS table in such a way that all queues
are utilized.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new hash key gives better distribution of packets across RX
queues.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detect error in Lancer by polling a HW register and
recover from this error if it is recoverable.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX queues are created again after error recovery,
netif_set_real_num_tx_queues() is invoked to update number of real
TX queues created. rtnl lock needs to be held when invoking this routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SR-IOV implementation is Lancer has changed in following ways -
1)PF driver assigns one MAC addresses for VF using COMMON_SET_IFACE_MAC_LIST.
2)VF driver queries its MAC address using COMMON_GET_IFACE_MAC_LIST command
and assigns it to its interface.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use V1 version of query link status command for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable VLAN promiscous mode, the HW interface should be created
with VLAN promiscous capability in Lancer. Add this capability during
creation of the HW interface.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented eeprom dump using ethtool feature for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement register dump using ethtool for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer uses V1 version of TXQ create. This command needs interface
id for TX queue creation. Rearrange code such that tx queue create
is after interface create. As TXQ create is now called after MCC
ring create use MCC instead of MBOX.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FW cmd timeout (with a sufficiently large timeout value in the
order of tens of seconds) indicates an unresponsive FW. In this state
issuing further cmds and waiting for a completion will only stall the process.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're spamming error messages each time a FW cmd call is made
while in EEH/UE error state. One log msg on error detection is enough.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize if_handle, vf_if_handle and vf_pmac_id with "-1" so that in
failure cases when be_clear() is called, we can skip over
if_destroy/pmac_del cmds if they have not been created.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
