On a busy network, the macb driver could get stuck in the interrupt
handler, quickly triggering the watchdog, due to a confluence of
factors:
1. macb_poll re-enables interrupts unconditionally, even when it will
be called again because it exhausted its rx budget
2. macb_interrupt only disables interrupts after scheduling
macb_poll, but scheduling fails when macb_poll is already scheduled
because it didn't call napi_complete
3. macb_interrupt loops until the interrupt status register is clear,
which will never happen in this case if the driver doesn't disable
the RX interrupt
Since macb_interrupt runs in interrupt context, this effectively locks
up the machine, triggering the hardware watchdog.
This issue was readily reproducible on a flooded network with a
modified 2.6.27.48 kernel. The same problem appears to still be in the
2.6.36-rc8 driver code, so I am submitting this patch against that
version. I have not tested this version of the patch except to make
sure the kernel compiles.
Signed-off-by: Joshua Hoke <joshua.hoke@sixnet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're setting skb->ip_summed to CHECKSUM_NONE for all non-TCP pkts, making the stack
recompute checksum.This is a bug for UDP pkts for which cso must be used.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling netif_carrier_off before register_netdev was causing the network interface
to miss a linkwatch pending event leading to an inconsistent state if the link
is not up when interface is initialized.This is now invoked after register_netdev.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only negative return from bind_qsets() should be considered an error and
propagated.
It fixes an issue reported by IBM on P Series platform.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Tested-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also correct the byteswapping as we keep the TCI in host order.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding VLAN devices, we can get several calls to
typhoon_set_rx_mode() in quick succession. Because we didn't wait for
the commands to complete, we could run out of command descriptors and
fail to set the RX mode.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding shutdown function that setup wake if wol is enabled.
Add jme_phy_on in jme_set_100m_half in case it is shutting down
or suspending when interface is down(phy_off by default).
v2 updates:
Removed CONFIG_PM ifdef for jme_set_100m_half and jme_wait_link.
It would be nice if it can be applied to net-2.6 along with other patches
sent few days ago. If it is not appropriate, please ignore the net-2.6
request, and apply it to net-next-2.6 as previous patch. :)
Reported-and-helped-by: Сtac <Taoga@yandex.ru>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a le64, not a le32, typo in one place only.
Noticed by sparse:
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: warning: incorrect type in assignment (different base types)
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: expected restricted __le64 [usertype] confPA
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: got restricted __le32 [usertype] <noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier to just annotate the constants as little endian types and set/clear
the flags directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit "net: allocate tx queues in register_netdevice"
netif_tx_stop_all_queues and related functions could be used between
device allocation and registration but now only after registration.
cxgb4 has such a call before registration and crashes now. Move it
after register_netdev.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Technologic Systems TS-CAN1 PC104 peripheral boards.
Signed-off-by: Andre B. Oliveira <anbadeol@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make many functions that are only used in one file static.
Remove dead code for override_led_value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has lots of unused code to dump data structures to
console. Use existing simple way to remove the code with ifdef.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use results of make namespacecheck to make functions local and
remove code that is not used.
Also rename initialize_ethtool_ops to vxge_initialize_ethtool_ops.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used directly by any drivers:
phy_attach_direct
phy_device_create
phy_prepare_link
genphy_config_advert
genphy_setup_forced
phy_config_interrupt
phy_clear_interrypt
phy_sanitize_settings
phy_enable_interrupts
phy_disable_interrupts
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following code and data are defined but never used in current
driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the following function static: mlx4_UNMAP_ICM
Remove the following unused function: mlx4_MAP_ICM_page
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While there replace all usage of self defined DRV_NAME by KBUILD_MODNAME.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While there, remove "printk()" on driver loading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
...by adding the correct annotation "__devinit" to the driver's probe
function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following compiler warning:
drivers/net/can/at91_can.c: In function 'at91_irq_err_state':
drivers/net/can/at91_can.c:779: warning: 'reg_ier' may be used uninitialized in this function
drivers/net/can/at91_can.c:779: warning: 'reg_idr' may be used uninitialized in this function
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv is part of the memory allocated by alloc_candev().
This patch moved the free it after last usage of priv.
While there convert all free_netdev() to free_candev() (which is currently
just a wrapper around free_netdev()) to be symetrically with the allocation
via alloc_candev().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT91_MID_MIDE bit must be set in order to receive extended frames.
The reception of an extended frame sets this bit, while reception of
standard frames resets it. This results in some lost extended frames in
an extended ID only environment. But leads to unpredictable lost
extended ID frames in a mixed environment.
The problem is fixed by setting the AT91_MID_MIDE after reception of a
CAN frame.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAN driver of Topcliff PCH
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus.
Topcliff PCH has CAN I/F. This driver enables CAN function.
Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: introduce CONFIG_BKL.
dabusb: remove the BKL
sunrpc: remove the big kernel lock
init/main.c: remove BKL notations
blktrace: remove the big kernel lock
rtmutex-tester: make it build without BKL
dvb-core: kill the big kernel lock
dvb/bt8xx: kill the big kernel lock
tlclk: remove big kernel lock
fix rawctl compat ioctls breakage on amd64 and itanic
uml: kill big kernel lock
parisc: remove big kernel lock
cris: autoconvert trivial BKL users
alpha: kill big kernel lock
isapnp: BKL removal
s390/block: kill the big kernel lock
hpet: kill BKL, add compat_ioctl
Simple pasting job using the new ops function. Also fix a couple of devices
directly returning the internal struct (which happens at this point to match
for the fields that matter but isn't correct or futureproof)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some cards don't support changing vlan offloading settings. Make
Ethtool set_flags return -EINVAL in those cases.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
Make local functions static. Remove functions that are
defined and never used. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to use one of the priority codes allowed by CNA f/w for NIC traffic
from host. The driver gets the bit map of the priority codes allowed for
host traffic through a asynchronous message from the f/w that the driver
subscribes to.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the patches we have queued in the BKL removal tree, only a
few dozen modules are left that actually rely on the BKL, and even
there are lots of low-hanging fruit. We need to decide what to do
about them, this patch illustrates one of the options:
Every user of the BKL is marked as 'depends on BKL' in Kconfig,
and the CONFIG_BKL becomes a user-visible option. If it gets
disabled, no BKL using module can be built any more and the BKL
code itself is compiled out.
The one exception is file locking, which is practically always
enabled and does a 'select BKL' instead. This effectively forces
CONFIG_BKL to be enabled until we have solved the fs/lockd
mess and can apply the patch that removes the BKL from fs/locks.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>