Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource makes the request
(and thus the detection) fail.
This fixes lm-sensors ticket #2306:
http://www.lm-sensors.org/ticket/2306
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
ibmpex's temperature sensors report incorrect units. Apply a conversion
factor so that tempertures report correctly. Until now, no systems seemed to
report temperatures this way, but evidently QS2x blades do.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhanced the list of supported machines.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The QS2x blades ships with v2.54 of the firmware, which use the same
multiplier for all power meters.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for family 0x17, which has Penryn Core. It should also
cover the 8 cores Xeons.
Can someone test please? I think it should work.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following patch will finally solve the detection of Intel Mobile CPUs which
share same CPUID with Desktop/Server CPUs. We need this information to test
some bit so we know if TjMax is 100C or 85C. Intel claims this works for mobiles
only, respect that and set for desktops the TjMax to 100C. Intel provided some
table on their wiki based on my chat with them at:
http://softwarecommunity.intel.com/isn/Community/en-US/forums/30247249/ShowThread.aspx#30247249
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
On my mid-2007 MacBook2, reading Ts0P sensor always failed with this message:
applesmc: wait status failed: 5 != 50.
So I assume that there's no such Ts0p sensor in this model (please confirm,
anyone). If there's the case, then we need a new set of sensors defined for
MacBook2.
Signed-off-by: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix following warning:
WARNING: vmlinux.o(.text+0xebfd04): Section mismatch in reference from the function coretemp_cpu_callback() to the function .cpuinit.text:coretemp_device_add()
coretemp_cpu_callback() are only used inside a
HOTPLUG_CPU block so annotate it __cpuinit.
The notifier referencing the function are annotated
__refdata to silence warning from the exit function.
The unregister function do not use the embedded pointer
but clears the variable so the annotation is OK.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following patch will add reporting of maximum temperature, at which all fans
should spin full speed. It may be non-physical temperature on Desktop/Server CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The missing NULL at the end of two sysfs file groups causes a kernel
crash when calling sysfs_create_group().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm and fault files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use standard dynamic sysfs callbacks instead of macro-generated
functions. This makes the code more readable, and the binary smaller
(by about 34%).
As a side note, another benefit of this type of cleanup is that they
shrink the build time. For example, this cleanup saves about 29% of
the lm80 driver build time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Drop trailing whitespace
* Fold a long line
* Rename new_client to client
* Drop redundant initializations to 0
* Drop bogus comment
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm and beep files. The
code was copied from the w83781d driver. I've tested the alarm files
on a W83627THF. I couldn't test the beep files as the system in
question doesn't have a speaker.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
If VBAT monitoring is disabled, enable it. Bug reported on the
lm-sensors trac system:
http://lm-sensors.org/ticket/2282
This is the exact same patch that was applied to the w83627ehf driver
6 months ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
While the W83627EHF/EHG has only 6 VID pins, the W83627DHG has 8 VID
pins, to support VRD 11.0. Add support for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
I did not create alarm files for in5 and in6 as these alarms are documented
as not working.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use standard dynamic sysfs callbacks instead of macro-generated
wrappers. This makes the code more readable, and the binary smaller
(by about 12%).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Drop history, it's incomplete and doesn't belong there
* Drop unused version number
* Drop trailing spaces
* Coding style fixes
* Fold long lines
* Rename new_client to client
* Drop redundant initializations to 0
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
What was true of reading the VRM value is also true of writing it: not
being a register value, it doesn't need hardware access, so we don't
need a reference to the i2c client. This allows for a minor code
cleanup. As gcc appears to be smart enough to simplify the generated
code by itself, this cleanup only affects the source code, the
generated binaries are unchanged.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The dme1737 has a second place where the Super-IO device ID is
checked. This has been missed by Jean's initial patch that adds
support for user-controlled Super-IO device ID override. This patch
fixes this issue.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes a possible divide-by-0 and a minor bug in the
FAN_FROM_REG macro (in TPC mode).
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Abit IP35 Pro has 6 fan connectors (CPU, SYS and AUX1-4), but the
entry for AUX4 was missing from the table.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Steve Hardy <steve@linuxrealtime.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs this. As the old library never had support for
the lm77 driver, I even dropped the legacy "alarms" file.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Many I2C hwmon drivers define a driver ID but no other code references
these, meaning that they are useless. Discard them, along with a few
IDs which are defined but never used at all.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Make the pwmN_enable files writable. This makes it possible to use
standard fan speed control tools (pwmconfig, fancontrol) with the lm85
driver.
I left the non-standard pwmN_auto_channels files in place, as they
give additional control for the automatic mode, and some users might
be used to them by now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The values returned by the lm85 driver in pwmN_enable sysfs files do
not match the standard. Fix that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use the standard dynamic sysfs callbacks instead of macro-generated
wrappers. It makes the code more simple and the binary smaller (-8% on
my system.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Rename new_client to client
* Drop redundant initializations to 0
* Drop trailing space
* Other whitespace cleanups
* Split/fold a few long lines
* Constify static data
* Optimizations in set_fan_div()
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Don't rely on the register cache when setting a new fan clock divider.
For one thing, the cache might not have been initialized at all if the
driver has just been loaded. For another, the cached values may be old
and you never know what can happen in the driver's back.
Also invalidate the cache instead of trying to adjust the measured fan
speed: the whole point of changing the clock divider is to get a better
reading.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
In commit f8d0c19a93 I forgot to delete
the pwmN_freq files on driver removal, here's the fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Drop unused defines
* Drop unused driver ID
* Remove trailing whitespace
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The W83627HF hardware monitoring features are supported by the
w83627hf driver for several years now. Support by the w83781d has
been advertised as deprecated 6 months ago, it's about time to see
it go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
On the ADM1026, pins 27 and 28 can be used for two different functions:
either temp3, or in8+in9. We should only create the sysfs files for the
function that is configured, otherwise it is confusing for the user.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Various cleanups:
* Drop an unused define.
* Drop unused struct member "type".
* Drop one useless instruction.
* Drop redundant initializations to 0.
* Rename new_client to client.
* Drop a useless cast.
* Minor code cleanup.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
