We were forgetting to call sunsu_change_speed(). The reason
that replugging in the mouse cable "fixes things" is that
causes a BREAK interrupt which in turn caused a call to
sunsu_change_speed() which would get the chip setup properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide support for drivers/char/rtc.c ioctls in the
Mostek rtc driver as well as the Sparc specific RTCGET
and RTCSET.
This allows userspace to be much less messy. Currently
util-linux and other spots jump through hoops trying
various ioctl variants until it hits the right one whatever
driver actually being used supports.
Eventually all of this should move over to the genrtc.c
driver, but not today...
While we are here, fix up the register types for sparse.
Thanks to Frans Pop for helping point out this issue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MSI test for chips that support MSI. If MSI test fails, it will
switch back to INTx mode and will print a message asking the user to
report the failure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the
offset is not 4-byte aligned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out
is enabled, certain NVRAM registers cannot be written to.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as
output when it is unused.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup proper GPIO settings in tp->grc_local_ctrl before calling
tg3_set_power() state in tg3_get_invariants() and after chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.
On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and
TG3_FLG2_5750_PLUS flags.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite of a couple of troublesome multi-way if statements to use
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of two-way if statements checking for 5750, and/or
5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of three-way if statements checking for 5705, 5750,
and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl.
Next patch will change entry to use pci_ids.h-based definition.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ASIC_REV_5752 definition.
Track-down all references to ASIC_REV_5750 and mirror them with
references to the newly defined ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's
allocation fix. Multichannel ISO receive still sucks; it should be possible
to use both legacy and non-legacy modes at the same time, but with this
patch, things are no worse than they were in 2.6.11 and allocation is
still done at the correct time.
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Print the correct value in the DBGMSG in dma_rcv_tasklet().
See OHCI 1.1 section 8.7, page 103 ff.
- Print tlabels as %d everywhere.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed a case in sr_ioctl.c's sr_get_mcn where a buffer is
allocated, but the pointer isn't checked for null.
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make transport-functions structure non-static. Replace #include of
scsi_transport.h with a forward declaration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We do not longer use DLT_LINUX_SLL for activ/pass filters but
DLT_PPP_WITHDIRECTION witch need 1 as outbound flag.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My version of gcc doesn't warn about this error (declaration in the
middle of a set of statements).
The fix is simple (this also corrects return code; for init functions it
should be zero or error).
I can't use list.h, since sk_buff doesn't have a list_head but instead
has two struct sk_buff pointers, and I want to avoid any extra memory
allocation.
send outgoing packets in order
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore.
We need to do it ourselves now.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore. Do it
ourselves if we are finished populating the device directory.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore. Do it
ourselves if we are finished populating the device directory.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_add_devices can be used from within modules, so it should be
exported. This can for example happen if you have hotpluggable firmware in
an FPGA on a system on chip processor; in our case the FPGA is probed for
devices and the FPGA base code registers the devices it has found with the
kernel.
(akpm: I think this is reasonable from a licensing POV: it's unlikely that
anyone would be interested in merging such specialised modules into mainline,
and it's a GPL export).
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Tue, 2005-03-15 at 09:25 +0100, Hannes Reinecke wrote:
> The current implementation of the firmware class breaks a fundamental
> assumption in udevd: that the physical device can be initialised fully
> prior to executing the next event for that device.
Here we add a TIMEOUT value to the hotplug environment of the firmware
requesting event. I will adapt udevd not to wait for anything else, if
it finds a TIMEOUT key.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The it87 and via686a hardware monitoring drivers each create a sysfs
file named "alarms" in R/W mode, while they should really create it in
read-only mode. Since we don't provide a store function for these files,
write attempts to these files will do something undefined (I guess) and
bad (I am sure). My own try resulted in a locked terminal (where I
attempted the write) and a 100% CPU load until next reboot.
As a side note, wouldn't it make sense to check, when creating sysfs
files, that readable files have a non-NULL show method, and writable
files have a non-NULL store method? I know drivers are not supposed to
do stupid things, but there is already a BUG_ON for several conditions
in sysfs_create_file, so maybe we could add two more?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here comes a small cleanup patch for the via686a driver. I noticed the
following two non-fatal problems:
1* The device parent is explicitely set, but it's not needed because the
i2c core will do as the client is registered.
2* snprintf is used where strlcpy would suffice.
Fixing them brings the via686a driver in line with what other similar
drivers do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Real fix for big endian machines - crc must be calculated
using little endian byte order.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the Ethernet/RNDIS gadget driver (mostly for RNDIS):
- Fix brown-paper bag goof with RNDIS packet TX ... the wrong length
field got set, so Windows would ignore data packets it received.
- More consistent handling of CDC output filters (but not yet hooking
things up so RNDIS uses the mechanism).
- Zerocopy RX for RNDIS packets too (saving CPU cycles).
- Use the pre-allocated interrupt/status request and buffer, rather
than allocating and freeing one of each every few seconds (which
could fail).
- Some more "sparse" tweaks, making both dual-speed and single-speed
configurations happier.
- RNDIS speeds are reported in units of 100bps, not bps.
Plus two minor cleanups (whitespace, messaging).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of a bunch of redundant NULL pointer checks in drivers/usb/*,
there's no need to check a pointer for NULL before calling kfree() on it.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/class/audio.c
===================================================================
Checking for NULL before calling kfree() is redundant. This patch removes
these redundant checks and also makes a few tiny whitespace changes.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please accept the attached patch which adds the vendorid 0x0745 and
modelid 0x0001 (ID 0745:0001) "Syntech Information Co., Ltd."
The device is an USB IR cradle for a barcode scanner (CPT-8001C) from
Cipherlab.
From: Peter Favrholdt <pfavr@mip.sdu.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -u kernel-source-2.6.11/drivers/usb/serial/pl2303.c ../kernel-source-2.6.11/drivers/usb/serial/pl2303.c
I'm attaching a patch to fix status when using Siemens X65
mobile. This mobile use first byte instead of normal UART_STATE
byte.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/serial/pl2303.c
===================================================================
It's possible to unplug usb device and do tiocmset() and tiocmget() without
valid interface in pl2303 module.
The patch below check this and return -ENODEV if interface was removed.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -purN linux-05-04-11/drivers/usb/serial/pl2303.c linux-05-04-11.usb/drivers/usb/serial/pl2303.c
In response to complaints about excessive latency in the uhci-hcd driver
I'm planning to convert it to a top-half/bottom-half design. It turns out
that to do this, the USB API has to be modified slightly since the driver
will not be able to meet one of the guarantees in the current API. This
patch changes some kerneldoc, specifying the weaker guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation. It also removes some needless strings from
the non-debug version of the driver.
Signed-off-by: Chris Clayton <chris_clayton@f1internet.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, another case of a Zaurus ROM not telling the expected conformance lie;
this patch handles the lies told by the SL5600.
From: bender647@gmail.com
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the attached patch adds another USB device ID to the list. Seems the
device is known under multiple IDs.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the delay for the US_FL_GO_SLOW patch from 110us to 125.
Some delays need this extra delay includign Jan De Luyck's drive which spawned
the original increase from 110 to 110us. 125 is a microframe, so this delay
seems to make sense more than just be a random delay (thanks to David Brownell
for pointing that out after my original patch).
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/storage/transport.c
===================================================================
On ppc64:
drivers/usb/net/usbnet.c: In function `skb_return':
drivers/usb/net/usbnet.c:429: warning: int format, different type arg (arg 3)
drivers/usb/net/usbnet.c:429: warning: int format, different type arg (arg 3)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/usb/net/usbnet.c~usbnet-printk-warning-fix drivers/usb/net/usbnet.c
I am sorry that the last patch about 32 bit compat ioctl on
64 bit kernel actually breaks the usbdevfs. That is on the current
BK tree. I am retarded.
Here is the patch to fix it. Tested with USB hard disk and webcam
in both 32bit compatible mode and native 64bit mode.
Again, sorry about that.
From: Christopher Li <chrisl@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts a recent change to usb_set_interface(). The change worked
around a quirk in certain devices, but doing this in usbcore creates
needless regressions for other devices. More appropriate fixes won't
put such handling in usbcore.
Basically it's tricky to do a full software reset of USB device state, since
the devices don't all act the same. This adds a note to the kerneldoc for
the usb_reset_configuration() call to highlight the quirk this was working
around: endpoint data toggles not being reset.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First patch incorrectly changed state of the wait-queue usage to
TASK_UNINTERRUPTIBLE. Reverted to TASK_INTERRUPTIBLE.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch includes minor "sparse -Wbitwise" updates for the PCI based
HCDs. Almost all of them involve just changing the second parameter of the
suspend() method to a pm_message_t ... the others relate to how the EHCI
code walks in-memory data structures. (There's a minor bug fixed there too
... affecting the big-endian sysfs async schedule dump.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/hcd.h
===================================================================
This is the first of a few installments of PM API updates to match the
recent switch to "pm_message_t". This installment primarily affects
USB device drivers (for USB interfaces), and it changes the handful of
drivers which currently implement suspend methods:
- <linux/usb.h> and usbcore, signature change
- Some drivers only changed the signature, net effect this just
shuts up "sparse -Wbitwise":
* hid-core
* stir4200
- Two network drivers did that, and also grew slightly more
featureful suspend code ... they now properly shut down
their activities. (As should stir4200...)
* pegasus
* usbnet
Note that the Wake-On-Lan (WOL) support in pegasus doesn't yet work; looks
to me like it's missing a request to turn it on, vs just configuring it.
The ASIX code in usbnet also has WOL hooks that are ready to use; untested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/net/irda/stir4200.c
===================================================================
This has a variety of updates to the shared suspend/resume code for
PCI based USB host controllers.
- Cope with pm_message_t replacing the target system state.
This is actually a loss of functionality; PCI D1 and D2
states will no longer be used, and it's no longer knowable
that D3cold is on the way so power will be lost.
- Most importantly, some of the resume paths are reworked and
cleaned up. They're now an exact mirror of suspend paths,
and more care is taken to ensure the hardware is reactivated
before the hardware re-enables interrupts.
Plus comment and diagnostic cleanups; there are some nasty cases here
especially combined with swsusp, now they're somewhat commented.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/usb/core/hcd-pci.c~usb-resume-fixes drivers/usb/core/hcd-pci.c
Here's a tiny patch to add support for the Tapwave Zodiac (for
2.6.11.6). I've been meaning to send it in for a while but kept
upgrading my kernel and losing the changes :-) I own the device and it
works fine with the latest pilot-link beta.
From: Larry Battraw <lbattraw@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Jamieson Becker <jamie@jamiebecker.com> for the info
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -Naur -X dontdiff-osdl tmp/linux-2.6.12-rc2/drivers/usb/serial/visor.h linux-2.6/drivers/usb/serial/visor.h
Now that we export all the parameters, this is easy to do.
It also means that we can dump about 2000 lines of code that
were dedicated to doing this internally.
Additionally, this removes all the aic7xxx driver abuse
of SCSI timers which were embedded in the DV routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is just a simplistic patch to export all of the
aic7xxx internal transport parameters via the SPI
transport class. It doesn't actually alter the way the
driver works at all.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
CC [M] drivers/scsi/qla2xxx/qla_attr.o
drivers/scsi/qla2xxx/qla_attr.c: In function `qla2x00_sysfs_write_fw_dump':
drivers/scsi/qla2xxx/qla_attr.c:65: warning: implicit declaration of function `vfree'
drivers/scsi/qla2xxx/qla_attr.c:83: warning: implicit declaration of function `vmalloc'
drivers/scsi/qla2xxx/qla_attr.c:83: warning: cast to pointer from integer of different size
Also remove spurious inclusion of linux/version.h
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the following cleanups:
- make some needlessly global functions static
- remove one more kernel 2.2 #ifdef
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
these have been wrappers for the generic dma direction bits since 2.5.x.
This patch converts the few remaining drivers and removes the macros.
Arjan noticed there's some hunk in here that shouldn't. Updated patch
below:
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't use cmd->request->nr_hw_segments as it may not be initialized
(SG_IO in particular bypasses anything that initializes this and just
uses scsi_do_req to insert a scsi_request directly on the head of the
queue) and a bogus value here can trip up the checks to make sure that
the number of segments will fit in the queue ring buffer, resulting in
commands that are never completed.
Fix up several issues with PCI DMA mapping and failure to check return
values on the mappings.
Make the check for space in the ring buffer happen after the DMA mapping
is done since any checks done before the mapping has taken place are
bogus.
Doug Ledford <dledford@redhat.com>.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove internal lun discovery routines and support
structures.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add initial support for FC remote port infrastructure.
o Use fc_remote_port...() registration and block/unlock
functions.
o Consolidate 'attribute' (fc-remote/sysfs) helpers into
new qla_attr.c file.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove internal command queuing from the driver. As is, this
driver cannot tolerate cable-pulls as I/Os will begin to fail
by the upper layers.
o Should be used in conjuction with the
11-fc_rport_adds_2.diff patch.
o Removes qla_listops.h file -- no longer needed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes scsi_send_eh_cmnd() use sdev and shost instead of
referencing them through scmd-> everytime.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have a DID_IMM_RETRY to require a retry at once, but we could do with
a DID_REQUEUE to instruct the mid-layer to treat this command in the
same manner as QUEUE_FULL or BUSY (i.e. halt the submission until
another command returns ... or the queue pressure builds if there are no
outstanding commands).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
This patch mainly introduces support for point-2-point
topology.
From: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also broken design in its compat handlers - CONFIG_COMPAT doesn't
mean that there should be no native ioctls.
Signed-off-by: Andi Kleen <ak@muc.de>
Reworked with comments from Markus Lidel by:
Christoph Hellwig <hch@infradead.org>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix up two drivers that incorrectly were using the old return values for
their new-style EH methods and kill off scsi_obsolete.h that defined the
constants. The initio driver has all these constansts defined locally
and uses them internally, I'll fix that up some time later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_cmnd->serial_number_at_timeout doesn't serve any purpose
anymore. All serial_number == serial_number_at_timeout tests
are always true in abort callbacks. Kill the field. Also, as
->pid always equals ->serial_number and ->serial_number
doesn't have any special meaning anymore, update comments
above ->serial_number accordingly. Once we remove all uses of
this field from all lldd's, this field should go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_cmnd->internal_timeout field doesn't have any meaning
anymore. Kill the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have the scsi_print_* functions in the proper namespace for a long
time now and there weren't a lot users left.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have a DID_IMM_RETRY to require a retry at once, but we could do with
a DID_REQUEUE to instruct the mid-layer to treat this command in the
same manner as QUEUE_FULL or BUSY (i.e. halt the submission until
another command returns ... or the queue pressure builds if there are no
outstanding commands).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
This patch mainly introduces support for point-2-point
topology.
From: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also broken design in its compat handlers - CONFIG_COMPAT doesn't
mean that there should be no native ioctls.
Signed-off-by: Andi Kleen <ak@muc.de>
Reworked with comments from Markus Lidel by:
Christoph Hellwig <hch@infradead.org>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix up two drivers that incorrectly were using the old return values for
their new-style EH methods and kill off scsi_obsolete.h that defined the
constants. The initio driver has all these constansts defined locally
and uses them internally, I'll fix that up some time later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_cmnd->serial_number_at_timeout doesn't serve any purpose
anymore. All serial_number == serial_number_at_timeout tests
are always true in abort callbacks. Kill the field. Also, as
->pid always equals ->serial_number and ->serial_number
doesn't have any special meaning anymore, update comments
above ->serial_number accordingly. Once we remove all uses of
this field from all lldd's, this field should go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_cmnd->internal_timeout field doesn't have any meaning
anymore. Kill the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have the scsi_print_* functions in the proper namespace for a long
time now and there weren't a lot users left.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- add a comment to the device structure that the device_busy field
is now protected by the request_queue->queue_lock
- null out sdev->request_queue after the queue is released to trap
any (and there shouldn't be any) use after the queue is freed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current problem seen is that the queue lock is actually in the
SCSI device structure, so when that structure is freed on device
release, we go boom if the queue tries to access the lock again.
The fix here is to move the lock from the scsi_device to the queue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This driver has had it's own different infrastructure for doing this for
ages, but it's time it used the common one.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The attachment combines the most recent patch from
Yum Rayan <yum.rayan@gmail.com> (to reduce sg stack
usage), Adrian Bunk <bunk@stusta.de> (to fix check
after use) and me (fix elapsed time calculation
(duration) on ia64 machines).
I have modified the patch from Yum Rayan so kmalloc()
in sg_read() is only called for the (rare) code paths
that need them.
Changelog:
- reduce stack usage in sg_ioctl() and sg_read()
- fix check after use in sg_mmap()
- hold duration internally in milliseconds and
check current time later than held time
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The conditions that cause these calls to MD_BUG are not kernel bugs, just
oddities in what userspace is asking for.
Also convert analyze_sbs to return void, and the value it returned was
always 0.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a tiny race when de-registering an MD thread, in that the thread
could disappear before it is set a SIGKILL, causing send_sig to have
problems.
This is most easily closed by holding tasklist_lock between enabling the
thread to exit (setting ->run to NULL) and telling it to exit.
(akpm: ick. Needs to use kthread API and stop using signals)
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the formatting of some comments in 8250.c, and add a note that the
register_serial / unregister_serial shouldn't be used in new code.
We do this here in preference to adding to linux/serial.h, since that is used
by a number of non-8250 drivers which pretend to be 8250. It is not known
whether it would be appropriate to do so.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct unwinding in error path of mthca_init_icm().
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Decouple table of HCA features from exact HCA device type. Add a current FW
version field so we can warn when someone is using old FW. Add support for
new MT25204 HCA.
Remove the warning about mem-free support, since it should be pretty solid at
this point.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix RDMA in mem-free mode: we need to make sure that the RDMA context memory
is mapped for the HCA.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update initialization of receive queue to match new documentation. This
change is required to support new MT25204 HCA.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up mem-free mode support by introducing mthca_is_memfree() function,
which encapsulates the logic of deciding if a device is mem-free.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor tweaks to firmware command handling: kill off an unused get of a value,
and add a little more info to debug output.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement fast memory regions (FMRs), where the driver writes directly into
the HCA's translation tables rather than requiring a firmware command. For
Tavor, MTTs for FMR are separate from regular MTTs, and are reserved at driver
initialization. This is done to limit the amount of virtual memory needed to
map the MTTs. For Arbel, there's no such limitation, and all MTTs and MPTs
may be used for FMR or for regular MR.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Split Tavor and Arbel/mem-free index<->hw key munging routines, so that FMR
implementation can call correct implementation without testing HCA type (which
it already knows).
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add mthca_table_find() function, which returns the lowmem address of an entry
in a mem-free HCA's context tables. This will be used by the FMR
implementation.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add code for SYNC_TPT firmware command, which will be used by FMR
implementation.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add mthca_write64_raw() function, which will be used to write FMR entries that
are in ioremapped PCI memory.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Encapsulate the buddy allocator used for MTT segments. This cleans up the
code and also gets us ready to add FMR support.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make address handle verbs usable from interrupt context.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fill in missing fields in send completions.
Signed-off-by: Itamar Rabenstein <itamar@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug in MTT allocation in mem-free mode.
I misunderstood the MTT size value returned by the firmware -- it is really
the size of a single MTT entry, since mem-free mode does not segment the MTT
as the original firmware did. This meant that our MTT addresses ended up
being off by a factor of 8. This meant that our MTT allocations might
overlap, and so we could overwrite and corrupt earlier memory regions when
writing new MTT entries.
We fix this by always using our 64-byte MTT segment size. This allows some
simplification of the code as well, since there's no reason to put the MTT
segment size in a variable -- we can always use our enum value directly.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add code to support RDMA and atomic send work requests in mem-free mode.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CQ numbers are only 24 bits, so only print 6 hex digits and mask off reserved
part when reporting a CQ event.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On error path, only free doorbell records if we're in mem-free mode.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print IRQ number when NOP command interrupt test fails to help debugging.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Release mutex on error return path from mthca_alloc_db().
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix error handling in MR allocation for mem-free mode: mthca_free must get an
MR index, not a key.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doorbell record pages are allocated in HCA page size chunks (always 4096
bytes), so we need to divide by 4096 and not PAGE_SIZE when figuring out how
many pages we'll need space for.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's cleaner to kfree mthca_mr, and not rely on the fact that ib_mr is the
first field in mthca_mr.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first buffer of a memory region is not required to be page-aligned, so
don't return an error if it's not.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When posting a work request with immediate data, put the immediate data in the
immediate data field of the hardware's work request (rather than overwriting
the flags field).
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix calculation of rdb_shift by using original number of QPs, not
their slot in profile[] (which will be rearranged when we sort it).
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement more of the device_query method in mthca.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In mem-free mode, when allocating memory regions, make sure that the HCA has
context memory mapped to cover the virtual space used for the MPT and MTTs
being used.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix handling of MAD agent registrations with mgmt_class == 0. In this case
ib_umad should pass a NULL registration request to the MAD core rather than a
request with mgmt_class set to 0.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mask bits correctly from jhash result in ib_fmr_hash() so that the
computed bucket index is within our hash table. This fixes an SDP
crash.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate no longer needed include files
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the *wc field in ib_mad_recv_wc from pointing to a structure on the
stack to one allocated with the received MAD buffer. This allows a client to
access the *wc field after their receive completion handler has returned.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert IPoIB to use debugfs instead of its own custom debugging filesystem.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct and simplify calculation of static rate. We need to round up the
quotient of (local_rate - path_rate) / path_rate. To round up we add
(path_rate - 1) to the numerator, so the quotient simplifies to (local_rate -
1) / path_rate.
No idea how I came up with the old formula.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set skb->mac.raw on receive. This fixes crashes when this is
dereferenced, for example by netfilter or when PF_PACKET is used.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Both the RiscPC and (optionally) EBSA285 have floppy disk support. Allow this
option to be selected on these ARM platforms again.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ted has agreed to let me take over as maintainer of /dev/random and
friends. I've gone ahead and added a line to his entry in CREDITS.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
one of the last buildcheck errors on i386, thanks Randy again for double
checking.
Fix pnpbios section references:
make dmi_system_id pnpbios_dmi_table __initdata
Error: ./drivers/pnp/pnpbios/core.o .data refers to 00000100 R_386_32
.init.text
Error: ./drivers/pnp/pnpbios/core.o .data refers to 0000012c R_386_32
.init.text
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- plug various leaks and use after frees in the remove and
initialization failure path (some still left)
- remove useless global list of boards and use pci_set_drvdata instead
- unobsfucate init path by merging functions together
- kill various totally useless state variables
- .. probably more I forgot
Note that the tty part still generates lots of sparse warnings and there's
still a totally useless layer of function pointer indirections, but maybe
someone else will fix that bit up.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In function __generic_unplug_device(), kernel can use a cheaper function
elv_queue_empty() instead of more expensive elv_next_request to find
whether the queue is empty or not. blk_run_queue can also made conditional
on whether queue's emptiness before calling request_fn().
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fix 3 calls to module_param_string() in
driver/media/video/tuner-core.c and drivers/media/video/tda9887.c. In all
three places, the len and the perm parameter was switched.
Signed-off-by: Bert Wesarg <wesarg@informatik.uni-halle.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a possibility that a bio will be accessed after it has been freed
on SCSI. It happens if you submit a bio with BIO_SYNC marked and the
auto-unplugging kicks the request_fn, SCSI re-enables interrupts in-between
so if the request completes between the add_request() in __make_request()
and the bio_sync() call, we could be looking at a dead bio. It's a slim
race, but it has been triggered in the Real World.
So assign bio_sync() to a local variable instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes remaining u32 vs. pm_message_t confusions in -rc2-mm3. [There
are usb changes, too; they went to Greg on his request.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t confusion in remaining places. Fortunately
there's few of them.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t confusion in drivers/video. Should change no
code.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-rc2-mm1 still contains few places where u32 and pm_message_t. This fixes
drivers/serial [should change no code].
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately that
turned out not to be the case as Russel King pointed out. Here are fixes for
drivers/macintosh.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t in drivers/mmc, drivers/mtd and
drivers/scsi.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t in drivers/message.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here are fixes for drivers/media.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t in pcmcia.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes remaining u32s in drivers/ net.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here are fixes for drivers/char.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately
that turned out not to be the case as Russel King pointed out. Here are
fixes for Documentation and common code (mainly system devices).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows to use them on x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the i2c-i801.c and Kconfig files for
I2C support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the ahci.c file for AHCI mode SATA
support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the ata_piix.c and quirks.c file for
IDE mode SATA support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the piix.c file for IDE PATA support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows Kconfig to build the MV643xx ethernet driver on Pegasos
(CONFIG_PPC_MULTIPLATFORM) and adds what I think is a missing fix from
Dale's batch, that is remove SA_INTERRUPT and add SA_SHIRQ in there as the
interrupt is shared if I understand things correctly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My previous patch that added sleep support for uninorth-agp and some AGP
"off" stuff in radeonfb and aty128fb is breaking some configs. More
specifically, it has problems with rage128 setups since the DRI code for
these in X doesn't properly re-enable AGP on wakeup or console switch
(unlike the radeon DRM).
This patch fixes the problem for pmac once for all by using a different
approach. The AGP driver "registers" special suspend/resume callbacks with
some arch code that the fbdev's can later on call to suspend and resume
AGP, making sure it's resumed back in the same state it was when suspended.
This is platform specific for now. It would be too complicated to try to
do a generic implementation of this at this point due to all sort of weird
things going on with AGP on other architectures. We'll re-work that whole
problem cleanly once we finally merge fbdev's and DRI.
In the meantime, please apply this patch which brings back some r128 based
laptops into working condition as far as system sleep is concerned.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drm: fix r128_state.c switch statements.. in drivers/char/drm/r128_state.c
(linux-2.6.12-rc2), some breaks are missing in the switch statement. See
trivial fix below.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Johannes Stezenbach <js@linuxtv.org>
Fix http://bugme.osdl.org/show_bug.cgi?id=4395.
Patch by Manu Abraham and Gerd Knorr:
Remove redundant bttv_reset_audio() which caused the computer to freeze
with some bt8xx based DVB cards when loading the bttv driver.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
..as sync_page_io can be called on the write-out path.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
