Global SERR and Interrupt should be masked at shpchp driver unload time.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in
controller SERR-INT register. This might cause unpredicable
results. This patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits
in logical slot registers. This might cause unpredicable results. This
patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access bits in slot logical
registers. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access slot logical registers. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access SHPC working register
sets. This patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current PCHEHP driver doesn't have any code to program hotplug
parameters from firmware. So hotplug parameters are never programed at
hot-add time. This patch add support for programming hotplug
parameters to PCIEHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for _HPX (Hot Plug Parameter Extensions)
defined in ACPI3.0a spec.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the improper error message about OSHP evaluation
to debug message which is displayed only when pci_hotplug.ko is loaded
with debugging mode enabled. To do this, this patch adds a new module
parameter "debug_acpi" to pci_hotplug.ko for enabling/disabling debug
messages in acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that hotplug parameters are not programed
when PCI cards are hot-added by ACPIPHP, SHPCHP and PCIEHP driver. The
pci_dev structure being hot-added is not bound to ACPI handle, so we
need to trace PCI bus tree to find ACPI handle.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't call pci_enable_device from pciehp because the pcie port service driver
already does this.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpi_os_free should not be used by drivers outside
of acpi/*/*.c. Replace with kfree().
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When acpiphp_enable_slot() is failed, acpiphp does not change
the slot->flags. Therefore, when user tries to read power
status, acpiphp_get_power_status() returns the enable status
whether the slot is not really enabled.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered the problem that when there are some hotplug
slots are under the host bridge, the hotplug slots under the
p2p bridge are not treated as hotpluggable.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o hotplug slots add
When the hot-added PCI device is p2p bridge, acpiphp calls
find_p2p_bridge() to add hotplug slots.
o hotplug slots remove
When the hot-removing PCI device is p2p bridge, acpiphp
calls cleanup_p2p_bridge() to remove hotplug slots.
o notify handler exchange
When the p2p bridge is added, acpiphp changes the notify
hanlder.
If no bridge device is inserted into the hotpluggable PCI
slot, acpiphp installs the notify handler for function.
After the p2p bridge hot-add, acpiphp has to install the
notify handler for bridge. Because, the role of the
handlers are not same. The hot-remove case is ditto.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current acpiphp does not free acpi_device structs when the
PCI devices are removed. When the PCI device is added,
acpi_bus_add() fails because acpi_device struct has already
exists. So, _PRT method does not evaluate.
This patch fixes this issue.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SGI hotplug driver changes required to support Tollhouse system PCI
hotplug, and implements the PRF_HOTPLUG_SUPPORT feature bit.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The init function for the RPA PCI Hotplug driver returns -ENODEV in the
case that no hotplug-capable slots are detected in the system. This is
bad, since hot-capable slots can be added after boot to a purely virtual
POWER partition. This is also bad because DLPAR I/O operations depend
on the rpaphp module.
Change the rpaphp init module to return success for the case of
partitions that own no hotplug-capable slots at boot. Such slots can be
dynamically added after boot.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I encountered the problem that the insmod of the acpiphp
fails because of the mis-freeing of the memory.
I tested this patch on my tiger4 box.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the defines TRUE and FALSE and just uses 0 or 1.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
shpchprm_acpi.c and pciehprm_acpi.c are nearly identical. In addition,
there are functions in both these files that are also in acpiphp_glue.c.
This patch will remove duplicate functions from shpchp, pciehp, and
acpiphp and move this functionality to pci_hotplug, as it is not
hardware specific. Get rid of shpchprm* and pciehprm* files since they
are no longer needed. shpchprm_nonacpi.c and pciehprm_nonacpi.c are
identical, as well as shpchprm_legacy.c and can be replaced with a
macro.
This patch also changes acpiphp to use the common hpp code.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch converts drivers/pci to kzalloc usage.
Compile tested with allyes config.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current ACPIPHP driver scans only slots under the top level PCI-to-PCI
bridge. So hotplug PCI slots under the nested PCI-to-PCI bridge would
not be detected. For example, if the system has the ACPI namespace
like below, hotplug slots woule not be detected.
Device (PCI0) { /* Root bridge */
Name (_HID, "PNP0A03")
Device (P2PA) { /* PCI-to-PCI bridge */
Name (_ADR, ...)
Device (P2PB) { /* PCI-to-PCI bridge */
Name (_ADR, ...)
Device (S0F0) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
...
Device (S0F7) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
Device (S1F0) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
...
}
}
}
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When doing a hotplug removal of a PPB, sn_bus_store_sysdata()
needs to be called for the PPB and all of its children.
Acked-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code related to handling bus speed in SHPCHP driver is
unnecessarily complex. This patch cleans up and simplify that.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker correctly noted, that in function board_replaced in
drivers/pci/hotplug/cpqphp_ctrl.c, the variable src always has the
value 8, and therefore much code after the
...
if (rc || src) {
...
if (rc)
return rc;
else
return 1;
}
...
can never be called.
This patch removes the unreachable code in this function fixing kernel
Bugzilla #6073.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hotplug slot is under the host bridge,
DEVICE_ACPI_HANDLE(&bus->self->dev) fails since '&bus->self' was not set.
This patch fixes it.
This patch is based on kristen's latest patches.
I tested this patch on my Tiger4.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o This patch removes IDs (for slots management).
o This patch removes the slot register/unregister processes
from the init/exit phases. Instead, adds these processes
in the bridge add/cleanup phases.
o Currently, this change doesn't have any meanings. But
these changes are needed to support p2p bridge(with
hotplug slot)
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These patches add generic dock event handling to acpiphp. If there are
pci devices that need to be inserted/removed after the dock event, the
event notification will be handed down to the normal pci hotplug event
handler in acpiphp so that new bridges/devices can be enumerated.
Because some dock stations do not have pci bridges or pci devices that
need to be inserted after a dock, acpiphp will remain loaded to handle
dock events even if no hotpluggable pci slots are discovered.
You probably need to have the pci=assign-busses kernel parameter enabled
to use these patches, and you may not allow ibm_acpi to handle docking
notifications and use this patch.
This patch incorporates feedback provided by many.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we add a new bridge with subordinate busses, we should call make sure
that acpi is notified so that the PRT (if present) can be read and drivers
who have registered on this bus will be notified when it is started.
Also make sure to use the max reserved bus number for the starting the bus
scan.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't care about the confliction between
hotplug operation via sysfs and hotplug operation via attention
button. So if those ware conflicted, slot could be an unexpected
state.
This patch changes SHPCHP driver to handle slot state properly. With
this patch, slot events are handled according to the current slot
state as shown at the Table below.
Table. Slot States and Event Handling
=========================================================================
Slot State Event and Action
=========================================================================
STATIC - Go to POWERON state if user initiates
(Slot enabled, insertion request via sysfs
Slot disabled) - Go to POWEROFF state if user initiates removal
request via sysfs
- Go to BLINKINGON state if user presses
attention button when the slot is disabled
- Go to BLINKINGOFF state if user presses
attention button when the slot is enabled
The event handler of SHPCHP driver is unnecessarily very complex. In
addition, current event handler can only a fixed number of events at
the same time, and some of events would be lost if several number of
events happened at the same time.
This patch simplify the event handler by using 'work queue', and it
also fix the above-mentioned issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wait_for_ctrl_irq() function in SHPCHP driver is no longer needed.
This patch removes that. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unused 'pci_bus' member from controller structure.
This patch have no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver has a bug in its interrupt handler which cause
"IRQ #: nobody cared" oops. This problem can be reproduced easily by
the following operation.
# cd /sys/bus/pci/slots/<slot#>
# while true; do echo 1 > attention ; done &
The reason is that when command complete interrupt is raised, current
SHPCHP driver's interrupt handler returns IRQ_NONE regardless of if
the interrupt is handled or not.
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves slot name area into struct slot.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unnecessary 'magic' member from struct slot of
SHPCHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces kmalloc() and memset() pair with kzalloc() and
cleans up the arg of sizeof() in SHPCHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up pcihp_skelton.c as follows.
o Move slot name area into struct slot.
o Replace kmalloc with kzalloc and clean up the arg of sizeof()
o Fix the wrong use of get_*_status() functions.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver might cause system panic because of lack of
serialization. It can be reproduced very easily by the following
operation.
# cd /sys/bus/pci/slots/<slot#>
# while true; do echo 0 > power ; echo 1 > power ; done &
# while true; do echo 0 > power ; echo 1 > power ; done &
This patch fixes this issue by changing shpchp to get appropreate
semaphore for hot-plug operation.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups codes that check the command status. For this, it
introduces a new semaphore "cmd_sem" for each controller.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups some codes in shpchp_core.c. This patch has no
functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups init_slots() function of SHPCHP driver based on
pcihp_skelton.c. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested with allyesconfig.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Build break: Building PCI hotplug on PowerPC results in
a build break, due to failure to export symbols.
Reported today by Dave Jones <davej@redhat.com>:
drivers/pci/hotplug/rpaphp.ko needs unknown symbol pcibios_add_pci_devices
This patch fixes same problem in drivers/pci tree
Previous patch fixes the break in the arch/powerpc tree.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Error checking is scattered through various layers of the dlpar code,
leading to a somewhat opaque code structure. This patch consolidates
error checking in one routine, simplifying the code a tad. There's
also some whitespace cleanup here too.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup. Move structure initializer to bottom of file,
this allows elimination of eyeball-strain-inducing forward
declarations.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup. Add the prefix rpaphp_* to several generic-sounding routines.
Remove rpaphp_remove_slot(), which is a one-liner.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_enable_pci_slot()
has a fairly simple logic structure, once all of the debug printk's
are removed. Its called from only one place, and that place also
has a very simple structure once he printk's are removed. Merge
the two together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_unconfig_pci_adapter()
is really just three lines of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the thre lines.
Also, provide proper semaphore locking in the affected function
disable_slot()
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_eeh_remove_bus_device() is a dupe of
eeh_remove_bus_device(). Remove it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_config_pci_adapter()
is really just one line of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the one line.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_fixup_new_pci_devices() has been migrated to
pcibios_fixup_new_pci_devices() in
arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_find_pci_bus() has been migrated to
pcibios_find_pci_bus() in arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the AMD POGO errata on the hotplug controller where the
platform will lock up or reboot if PERR/SERR generation is enabled and a
slot is sent an enable command. This fix disables PERR/SERR generation
before a slot is sent the enable command by first saving related
registers, turning off SERR/PERR generation, enabling the slot, then
restoring the registers.
Signed-off-by: David Keck <david.keck@amd.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removing and then adding a PCI slot to a running partition results in
a kernel panic. The current code attempts to add iospace for an entire
root bus, which is inappropriate, and silently fails. When a pci device
tries to use the iospace, a page fault is taken, as the iospace had not
been mapped, and of course the page fault cannot be resolved.
This only occurs for PCI adapters using pio, which may be why it hadn't
been seen earlier (this seems to have been broken for a while).
This patch has survived testing of dozens of slot add and removes.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- hotplug/pciehp_core.c: make the needlessly global hpdriver_context
static
- #if 0 the following unused functions:
- pci.c: pci_bus_max_busnr()
- pci.c: pci_max_busnr()
- proc.c: pci_proc_attach_bus()
- remove.c: pci_remove_device_safe
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only size the bus that has been added.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Compaq PCI Hotplug driver was creating 2 sysfs files that contained
nothing but debug information, and had way more than "one value" in
them. This patch converts the code to use debugfs for these files
instead.
Compile tested only.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/pciehp_core.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code is slightly smaller
- small line length cleanup
- better readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/pciehprm_acpi.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code is slightly smaller
- better readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/rpaphp_pci.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code should be slightly smaller
- better readability
note: due to lack of both hardware and cross-compile tools this patch is,
unfortunately, completely untested.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr of pointer dereferences in
drivers/pci/hotplug/cpqphp_core.c
Benefits of this patch:
- micro speed optimization due to fewer pointer derefs
- generated code is slightly smaller
- tiny line length and whitespace cleanup
- better readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes bugs in the pciehp driver that prevent hot-add
of a card with PCI bridges on it.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disables power fault, MRL sensor and presence detection
interrupts when a PCIe slot is powered-off and enables those
interrupts when it is powered-on again. This is necessary to prevent
the associated events from causing an endless cycle of interrupts
due to the power-fault bit, which stays set till power is restored
to the slot.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch implements .get_address callback of
hotplug_slot_ops for SHPCHP driver. With this patch, we
can see bus address of hotplug slots as follows:
$ cat address
0000:0b:01
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP code contains two routines that appear to be gratuitous copies
of very similar pci code. In particular,
rpaphp_claim_resource ~~ pci_claim_resource
(there is a minor, non-functional difference)
rpadlpar_claim_one_bus == pcibios_claim_one_bus
(the code is identical)
This patch removes the rpaphp versions of the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP code contains a routine that duplicates some existing code.
This patch removes the rpaphp version of the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver uses msleep_interruptible() function to wait for
a command completion event. But I think this would cause an unnecessary
long wait until timeout, if command completion interrupt came before
task state was changed to TASK_INTERRUPTIBLE. This patch fixes this
issue. With this patch, command completion becomes faster as follows:
o Without this patch
# time echo 1 > power
real 0m4.708s
user 0m0.000s
sys 0m0.524s
o With this patch
# time echo 1 > power
real 0m2.221s
user 0m0.000s
sys 0m0.532s
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver writes a '0' to the Command Completion Detect
bit to clear the Command Complete Interrupt Pending. But according to
the SHPC spec (See 4.7.3.1 System Interrupts), SHPCHP driver must
write '1'. This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver seems not to map MMIO region properly. This
patch fixes this bug. This patch also cleanup the code.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hpc_get_mode1_ECC_cap() function of SHPCHP driver seems to refer
the wrong bit for refering the "Mode 1 ECC Capability" bit. This bug
seems not to cause any problem so far. But I think this should be
fixed. This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hpc_get_max_bus_speed() function of the SHPCHP driver seems to
refer wrong bits in the "Slot Avail Register I" and "Slot Avail
Register II". This patch fixes this bug. And this also cleanup the
code.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces pci_find_slot() with pci_get_slot() in the SHPCHP
driver. This enables SHPCHP driver to work on multiple PCI segment
systems.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we already did return -ENOMEM
if (!p_mem_node).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed what appears to be a cut/paste error in
drivers/pci/hotplug/ibmphp_pci.c:
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per the PCI Express spec, the power-fault-detected bit in the
slot status register can be set anytime hardware detects a power
fault, regardless of whether the slot has a device populated in
it or not. This bit is sticky and must be explicitly cleared.
This patch is needed to allow hot-add after such a power fault
has been detected.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/pci/hotplug/pciehp_hpc.c:221: parse error before "pcie_isr"
drivers/pci/hotplug/pciehp_hpc.c:221: warning: type defaults to `int' in declaration of `pcie_isr'
drivers/pci/hotplug/pciehp_hpc.c:221: warning: data definition has no type or storage class
drivers/pci/hotplug/pciehp_hpc.c: In function `hpc_release_ctlr':
drivers/pci/hotplug/pciehp_hpc.c:715: implicit declaration of function `free_irq'
drivers/pci/hotplug/pciehp_hpc.c: At top level:
drivers/pci/hotplug/pciehp_hpc.c:839: parse error before "pcie_isr"
drivers/pci/hotplug/pciehp_hpc.c:840: warning: return type defaults to `int'
drivers/pci/hotplug/pciehp_hpc.c: In function `pcie_isr':
drivers/pci/hotplug/pciehp_hpc.c:850: `IRQ_NONE' undeclared (first use in this function)
drivers/pci/hotplug/pciehp_hpc.c:850: (Each undeclared identifier is reported only once
drivers/pci/hotplug/pciehp_hpc.c:850: for each function it appears in.)
drivers/pci/hotplug/pciehp_hpc.c:979: `IRQ_HANDLED' undeclared (first use in this function)
drivers/pci/hotplug/pciehp_hpc.c: In function `pcie_init':
drivers/pci/hotplug/pciehp_hpc.c:1362: implicit declaration of function `request_irq'
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: _machine is some ppc64 thing - this is a powerpc-only driver)
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- access.c should #include "pci.h" for getting the prototypes of it's
global functions
- hotplug/shpchp_pci.c: make the needlessly global function
program_fw_provided_values() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the driver bits for enabling DLPAR and PCI Hotplug
for the new OF-based PCI probe. This functionality was regressed when
the new PCI approach was introduced. Please apply if appropriate.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current pciehp implementation reports a power-fail error
even if the condition has cleared by the time the corresponding
interrupt handling code gets a chance to run. This patch
fixes this problem.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch further tweaks how we request control of hotplug
controller hardware from BIOS. We first search the ACPI namespace
corresponding to a specific hotplug controller looking for an
_OSC or OSHP method. On failure, we successively move to the
ACPI parent object, till we hit the highest level host bridge
in the hierarchy. This allows for different types of BIOS's
which place the _OSC/OSHP methods at various places in the acpi
namespace, while still not encroaching on the namespace of
some other root level host bridge.
This patch also introduces a new load time option (pciehp_force)
that allows us to bypass all _OSC/OSHP checking. Not supporting
these methods seems to be be the most common ACPI firmware problem
we've run into. This will still _not_ allow the pciehp driver to
work correctly if the BIOS really doesn't support pciehp (i.e. if
it doesn't generate a hotplug interrupt). Use this option with
caution. Some BIOS's may deliberately not build any _OSC/OSHP
methods to make sure it retains control the hotplug hardware.
Using the pciehp_force parameter for such systems can lead to
two separate entities trying to control the same hardware.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tweaks the way pciehp requests control of the hotplug
hardware from BIOS. It now tries to invoke the ACPI _OSC method
for a specific hotplug controller only, rather than walking the
entire acpi namespace invoking all possible _OSC methods under
all host bridges. This allows us to gain control of each hotplug
controller individually, even if BIOS fails to give us control of
some other hotplug controller in the system.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of debug messages generated if pciehp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in pciehp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the PCI Express hotplug driver's dependence on ACPI.
We don't walk the acpi namespace anymore to build a list of
bridges and devices. We go to ACPI only to run the _OSC or
_OSHP methods to transition control of hotplug hardware from
system BIOS to the hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that pciehp
does not automatically enable the hot-added device or its DMA
bus mastering capability now. It expects the device driver to
do that. This may break some drivers and we will have to fix
them as they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the pci express hotplug controller driver
to use the PCI core for resource management. This eliminates a
lot of duplicated code and integrates pciehp with the system's
normal PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
19-rpaphp-crashing.patch
This patch fixes a bug related to dlpar PHB add, after a PHB removal.
-- The crash was due to the PHB not having a pci_dn structure yet,
when the phb is being added.
This code survived testing, of adding and removeig the PHB and all slots
underneath it, 17 times so far, as of this writing.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the remaining misc drivers/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in misc files in
drivers/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allocate resources for adapters with bridges on them.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At unload time, the shpchp driver does not remove sysfs files
it had created in the driver's probe entry point. This patch
fixes this problem.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of debug messages generated if shpchp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove un-necessary header includes, remove dead code, remove
some type casts, receive function return in the correct data
type...
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in shpchp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch eliminates saving the PCI config header for devices
in hotplug capable slots. We now use the PCI core to get the
specific parts of the config header as required.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The shpc driver registers its probe function for all pci-pci
bridges in the system. Not all of them will be shpc capable, so
look for this capability early in the probe function and return
if there's no work to do on this bridge. The old shpc driver
did some initialization work on all bridges before detecting
that shpc is not supported and unwinds the work it's already done
in that case.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the SHPC hotplug driver's dependence on ACPI. We don't
walk the acpi namespace anymore to build a list of bridges and
devices. The remaining interaction with ACPI is to run the
_OSHP method to transition control of hotplug hardware from
system BIOS to the shpc hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that shpchp
does not enable the hot-added device or its DMA bus mastering
automatically now. It expects the device driver to do that.
This may break some drivers and we will have to fix them as
they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Info about resources assigned to PCI devices is already available
through sysfs and pci utilities. There's no need for shpchp to
create another sysfs file to display the same information.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the standard hotplug controller driver to use
the PCI core for resource management. This eliminates a whole lot
of duplicated code, and integrates shpchp in the system's normal
PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a minor patch to the ppc64 PCI hotplug code; it makes the call to
rpaphp_unconfig_pci_adapter() symmetric with respect to the call to
rpaphp_config_pci_adapter(). I discussed this with John Rose, who
had provided the last round of changes for these functions; he
appearently had this patch but somehow failed to mail it out.
Tested. (added/removed device).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
drivers/pci/hotplug/rpaphp.h | 3 ++-
drivers/pci/hotplug/rpaphp_core.c | 5 ++++-
drivers/pci/hotplug/rpaphp_pci.c | 11 +++--------
3 files changed, 9 insertions(+), 10 deletions(-)
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpqphp relies on it.
This fixes a problem reported by Bruno Redondi. He reported a flood
of ACPI interrupts, that caused kacpid to run 100% of the time:
http://bugzilla.kernel.org/show_bug.cgi?id=5312
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/cpqphp_core.c | 24 +++++++++++++++++++-----
1 file changed, 19 insertions(+), 5 deletions(-)
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpcihp_zt5550 relies on it.
Compiled but untested, since I don't have the hardware.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/cpcihp_zt5550.c | 25 +++++++++++++++++++++----
1 file changed, 21 insertions(+), 4 deletions(-)
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: <kristen.c.accardi@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed
using pci_bus_{read,write}_config_dword(). A recent audit of drivers/
turned up several cases of byte- and word-sized accesses. The harmful
ones were fixed by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: <kristen.c.accardi@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Franc reported that the pciehp driver was not enabling bus
master capability on his hot-plugged card. pciehprm_enable_card()
was updating the PCI command register only if _HPP indicated a
value for SERR or PERR that was different from the current setting.
I don't have hardware that reproduces this problem, but Martin
reports that this patch fixes the problem for him.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From rzarev@its.caltech.edu Tue Sep 6 18:29:50 2005
Date: Tue, 6 Sep 2005 13:39:32 -0700 (PDT)
From: Rumen Ivanov Zarev <rzarev@its.caltech.edu>
Message-Id: <200509062039.j86KdWMr014934@inky.its.caltech.edu>
To: gregkh@suse.de
Subject: PCI: Unhide SMBus on Compaq Evo N620c
Cc: linux-kernel@vger.kernel.org
Trivial patch against 2.6.13 to unhide SMBus on Compaq Evo N620c laptop using
Intel 82855PM chipset.
Signed-off-by: Rumen Zarev <rzarev@caltech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
drivers/pci/quirks.c | 6 ++++++
1 file changed, 6 insertions(+)
--- gregkh-2.6.orig/drivers/pci/quirks.c 2005-09-09 10:28:55.000000000 -0700
+++ gregkh-2.6/drivers/pci/quirks.c 2005-09-09 13:51:44.000000000 -0700
@@ -876,6 +876,12 @@ static void __init asus_hides_smbus_host
case 0xC00C: /* Samsung P35 notebook */
asus_hides_smbus = 1;
}
+ } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) {
+ if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
+ switch(dev->subsystem_device) {
+ case 0x0058: /* Compaq Evo N620c */
+ asus_hides_smbus = 1;
+ }
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge );
This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn. The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices. It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These fixes were suggested by pcihpd-discuss, but were dropped in the
initial checkin of the code. These fixes include cleaning up the
hotplug driver sysfs filename, and some minor code cleanups. The driver
also requires at least PROM 4.30, not 4.20.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For systems with multiple hotplug controllers, you need to use more than
just the slot number to uniquely name the slot. Without a unique slot
name, the pci_hp_register() will fail. This patch adds the bus number
to the name.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently rpaphp registers the following bus types as hotplug slots:
1) Actual PCI Hotplug slots
2) Embedded/Internal PCI slots
3) PCI Host Bridges
The second and third bus types are not actually direct parents of
removable adapters. As such, the rpaphp has special case code to fake
results for attributes like power, adapter status, etc. This patch
removes types 2 and 3 from the rpaphp module.
This patch also changes the DLPAR module so that slots can be
DLPAR-added/removed without having been designated as hotplug-capable.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports rpaphp_config_pci_adapter() for use by the rpadlpar
module. It also changes this function by removing any dependencies on
struct slot. The patch also changes the RPA DLPAR-add path to enable
newly-added slots in a separate step from that which registers them as
hotplug slots.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rpaphp module currently uses a fragile method to find a pci device
by its device node. This function is unnecessary, so this patch scraps
it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The slot structure in the rpaphp module currently references the PCI
contents of the slot using the PCI device of the parent bridge. This
is unnecessary, since the module is actually interested in the
subordinate bus of the bridge. The dependency on a PCI bridge device
also prohibits the module from registering hotplug slots that have a
root bridge as a parent, since root bridges on PPC64 don't have PCI
devices.
This patch changes struct slot to reference the PCI subsystem using a
pci_bus rather than a pci_dev.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, rpaphp registers Virtual I/O slots as hotplug slots. The
only purpose of this registration is to ensure that the VIO subsystem
is notified of new VIO buses during DLPAR adds. Similarly, rpaphp
notifies the VIO subsystem when a VIO bus is DLPAR-removed. The rpaphp
module has special case code to fake results for attributes like power,
adapter status, etc.
The VIO register/unregister functions could just as easily be made from
the DLPAR module. This patch moves the VIO registration calls to the
DLPAR module, and removes the VIO fluff from rpaphp altogether.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is the SGI hotplug driver and additional changes required for
the driver. These modifications include changes to the SN io_init.c code
for memory management, the inclusion of new SAL calls to enable and disable
PCI slots, and a hotplug-style driver.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
drivers/pci/hotplug/cpqphp_core.c calls cpqphp_event_start_thread()
in one_time_init(), which is called whenever the hardware is probed.
Unfortunately, cpqphp_event_stop_thread() is *always* called when
the module is unloaded. If the hardware is never probed, then
cpqphp_event_stop_thread() tries to manipulate a couple of
uninitialized mutexes.
Signed-off-by: Keith Moore <keithmo@exmsft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds PCI based I/O xAPIC hot-add support to ACPIPHP
driver. When PCI root bridge is hot-added, all PCI based I/O xAPICs
under the root bridge are hot-added by this patch. Hot-remove support
is TBD.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current acpiphp code does not distinguish between the physical presence and
power state of a device/slot. That is, if a device has to be disabled, it
also tries to physically ejects the device. This patch decouples power state
from physical presence. You can now echo to the corresponding sysfs power
control file to repeatedly enable and disable a device without having to
physically re-insert it.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpiphp changes to support acpi based root bridge hot-add.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earlier I reported that Matthew's acpiphp rewrite had problem in powering down
slot on my i386 system. The following patch is needed to get the acpiphp
rewrite properly powering down the slot.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A root bridge may not have directly attached hotpluggable slots under it.
Instead, it may have p2p bridges with slots under it. In this case, we need
to clean up the p2p bridges and slots properly too. Patch below applies on
top of the original patch, and fixes this problem. Without this, acpiphp
leaves behind notify handlers on module unload, and subsequent module load
attempts don't work properly too. Patch was tested on an ia64 Tiger4 box.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts acpiphp to use the generic PCI resource assignment code.
It's quite large, but most of it is deleting the acpiphp_pci and acpiphp_res
files. It's tested on an hp Integrity rx8620 (which won't work without this
patch). Testers with other hardware welcomed.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs: fix drivers/pci so if an attribute does not implement
show or store method read/write will return -EIO
instead of 0.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a patch that fixes up the pci_dev refcounting in the CPCI code.
I've done some testing against it and it seems fine here.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is my third attempt at a patch to further update the CompactPCI
hotplug driver infrastructure to address the pci_enable_device issue
discussed on the list as well as a few other issues I discovered during
some more testing. This version addresses a few more issues pointed out
by Prarit Bhargava. Changes include:
- cpci_enable_device and its recursive calling of pci_enable_device on
new devices removed.
- Use list_rwsem to avoid slot status change races between disable_slot
and check_slots.
- Fixed oopsing in cpci_hp_unregister_bus caused by calling list_del on
a slot after calling pci_hp_deregister.
- Removed kfree calls in cleanup_slots since release_slot will have
done it already.
- Reworked init_slots a bit to fix latch and adapter file updating on
subsequent calls to cpci_hp_start.
- Improved sanity checking in cpci_hp_register_controller.
- Now shut things down correctly in cpci_hotplug_exit.
- Switch to pci_get_slot instead of deprecated pci_find_slot.
- A bunch of CodingStyle fixes.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver doesn't seem to program command register to
enable PERR and SERR properly. The following patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver doesn't seem to program _HPP values
properly. The following patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] CPCI: update
I have finally done some work to update the CompactPCI hotplug driver to
fix some of the outstanding issues in 2.6:
- Added adapter and latch status ops so that those files will get created
by the current PCI hotplug core. This used to not be required, but
seems to be now after some of the sysfs rework in the core.
- Replaced slot list spinlock with a r/w semaphore to avoid any potential
issues with sleeping. This quiets all of the runtime warnings.
- Reworked interrupt driven hot extraction handling to remove need for a
polling operator for ENUM# status. There are a lot of boards that only
have an interrupt driven by ENUM#, so this lowers the bar to entry.
- Replaced pci_visit_dev usage with better use of the PCI core functions.
The new code is functionally equivalent to the previous code, but the
use of pci_enable_device on insert needs to be investigated further, as
I need to do some more testing to see if it is still necessary.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is the updated patch to get pciehp driver to work for downstream
port of a switch and handle the difference in the offset value of PCI
Express capability list item of different ports.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch to fix the problem of echoing 1 to "power" file
to enabled slot causing the slot to power down, and echoing 0
to disabled slot causing shpchp_disabled_slot() to be called
twice. This problem was reported by kenji Kaneshige.
Thanks,
Dely
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I fogot to remove the code that freed the memory in cleanup_slots().
Here is the new patch, which I have also taken care of the comment
by Eike to remove the cast in hotplug_slot->private.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
here is the patch that fixes the bug introduced by my previous patch which
already went into 2.6.12-rc2 and is likely to cause trouble is someone hits
one the else case here by accident.
Using the &= operation before the if statement destroys the information the
if asks for so we always go into the else branch.
Signed-off-by: Rolf Eike Beer <eike-hotplug@sf-tec.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
