Wireless Broadcom chips can have either their SPROM data stored
on either external SPROM or on-chip OTP memory. Both are accessed
through the same register space. This patch adds support for the
on-chip OTP memory.
Tested with:
BCM43224 OTP and SPROM
BCM4331 SPROM
BCM4313 OTP
This patch is in response to linux-wireless thread [1].
[1] http://article.gmane.org/gmane.linux.kernel.wireless.general/85426
Tested-by: Saul St. John <saul.stjohn@gmail.com>
Tested-by: Rafal Milecki <zajec5@gmail.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For A-MPDU rx it makes sense to only process the signal strength once per
aggregate instead of once per subframe. Additonally, some hardware (e.g.
Atheros) only provides valid signal strength information for the last
subframe.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot to update the kernel-doc in my patch
to redesign AP mode APIs, fix that now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is needed by the bcm47xx arch code to get the number of
the ieee80211 core.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch extends the sprom struct to contain all sprom attributes
found in sprom version 1 to 9. This was done accordingly to the open
source part of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This member contains the country code encoded with two chars
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On sprom version 4 and 5 there are 4 values for pa_2g, pa_5gl, pa_5g
and pa_5gh, for sprom version 8 and 9 there are only 3. Make the per
path sprom store also work for older sprom versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some parts of the sprom struct are bigger than needed.
The leddc and maxpwr values are just 8 bit long and not 16.
rxpo2g and rxpo5g are signed
I got these information for the open source part of the Broadcom SDK
covering sprom version 1 to 9. rxpo2g contained a negative number on my
bcm5354 based device, this cased an error and Broadcom SDK says this is
signed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
queue_delayed_work() expects a relative time for when that work
should be scheduled.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This check is needed on the BCM43224 device as it says in the
capabilities it has an sprom but is extra check says it has not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have two bcma buses on one computer the second will not work
without this patch. Now each bus gets an own number.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_core_pci_hostmode_init() has to be in __devinit as it will call a
function in that section and so all functions calling it also have to
be in __devinit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are many magic numbers used in the PCIe code. Replace them with
some constants from the Broadcom SDK and also use them in the pcie host
controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SoCs have two pcie or gmac cores and we need to know the number of
the specific core on the bus. This is the case for the BCM4706.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed by mac80211 to keep a reference
to a BSS alive for the auth process. Remove the
old version of cfg80211_ref_bss() since it's
not actually used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e4d, since it
became a per-ns value.
That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.
This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.
It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
By definition net_generic should never be called when it can return
NULL. Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.
Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys. It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new kernel-doc warnings:
Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 36a1211970 removed linux/module.h
include statement from one of the headers that end up in net/sock.h.
It was providing us with static_branch() definition implicitly, so
after its removal the build got broken.
To fix this, and avoid having this happening in the future,
let me do the right thing and include linux/jump_label.h
explicitly in sock.h.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davem says:
1) Fix JIT code generation on x86-64 for divide by zero, from Eric Dumazet.
2) tg3 header length computation correction from Eric Dumazet.
3) More build and reference counting fixes for socket memory cgroup
code from Glauber Costa.
4) module.h snuck back into a core header after all the hard work we
did to remove that, from Paul Gortmaker and Jesper Dangaard Brouer.
5) Fix PHY naming regression and add some new PCI IDs in stmmac, from
Alessandro Rubini.
6) Netlink message generation fix in new team driver, should only advertise
the entries that changed during events, from Jiri Pirko.
7) SRIOV VF registration and unregistration fixes, and also add a
missing PCI ID, from Roopa Prabhu.
8) Fix infinite loop in tx queue flush code of brcmsmac, from Stanislaw Gruszka.
9) ftgmac100/ftmac100 build fix, missing interrupt.h include.
10) Memory leak fix in net/hyperv do_set_mutlicast() handling, from Wei Yongjun.
11) Off by one fix in netem packet scheduler, from Vijay Subramanian.
12) TCP loss detection fix from Yuchung Cheng.
13) TCP reset packet MD5 calculation uses wrong address, fix from Shawn Lu.
14) skge carrier assertion and DMA mapping fixes from Stephen Hemminger.
15) Congestion recovery undo performed at the wrong spot in BIC and CUBIC
congestion control modules, fix from Neal Cardwell.
16) Ethtool ETHTOOL_GSSET_INFO is unnecessarily restrictive, from Michał Mirosław.
17) Fix triggerable race in ipv6 sysctl handling, from Francesco Ruggeri.
18) Statistics bug fixes in mlx4 from Eugenia Emantayev.
19) rds locking bug fix during info dumps, from your's truly.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
rds: Make rds_sock_lock BH rather than IRQ safe.
netprio_cgroup.h: dont include module.h from other includes
net: flow_dissector.c missing include linux/export.h
team: send only changed options/ports via netlink
net/hyperv: fix possible memory leak in do_set_multicast()
drivers/net: dsa/mv88e6xxx.c files need linux/module.h
stmmac: added PCI identifiers
llc: Fix race condition in llc_ui_recvmsg
stmmac: fix phy naming inconsistency
dsa: Add reporting of silicon revision for Marvell 88E6123/88E6161/88E6165 switches.
tg3: fix ipv6 header length computation
skge: add byte queue limit support
mv643xx_eth: Add Rx Discard and Rx Overrun statistics
bnx2x: fix compilation error with SOE in fw_dump
bnx2x: handle CHIP_REVISION during init_one
bnx2x: allow user to change ring size in ISCSI SD mode
bnx2x: fix Big-Endianess in ethtool -t
bnx2x: fixed ethtool statistics for MF modes
bnx2x: credit-leakage fixup on vlan_mac_del_all
macvlan: fix a possible use after free
...
A considerable effort was invested in wiping out module.h
from being present in all the other standard includes. This
one leaked back in, but once again isn't strictly necessary,
so remove it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes event message behaviour to send only updated records
instead of whole list. This fixes bug on which userspace receives non-actual
data in case multiple events occur in row.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: Pass information that quota is stored in system file to userspace
ext2: protect inode changes in the SETVERSION and SETFLAGS ioctls
jbd: Issue cache flush after checkpointing
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
