It was obesrved that at least one older PCI card predating the
requirement for the TRDY signal to respond within 16 clock ticks actually
does not meet this rule nor even the power-on defaults of the PCI bridges
found in development systems built around the Broadcom SiByte SOCs. Here
is a patch that bumps up the timeout to the highest finite value supported
by these chips, which is 255 clock ticks. The bridges affected are the
SiByte SOC itself and the SP1011.
This change does not effectively affect systems only having PCI option
cards installed that meet the TRDY requirement of the current PCI spec.
The rule was introduced with PCI 2.1, so any older card may make the
system affected. If this is the case, performance of the system will
suffer in return for the card working at all. If this is a concern, then
the solution is not to use such cards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
The following change updates the Atlas interrupt handling to match that
of Malta. Tested with a 5Kc and a 34Kf successfully.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've encountered a serious problem with PCI config space access on Au1x000
platforms with recent 2.6.x-kernel. With 2.4.31 the same hardware works fine.
So I was looking for the differences:
Symptoms:
- no PCI-device is seen on bootup though two or three cards are present
- lspci output is empty
- OR: lspci shows 20 times the same device
(- OR: in some slot-configurations it worked anyhow)
System(s):
1. platform with Au1500 and three PCI-devices (actually a mycable XXS1500
with backplane for three PCI-devices)
2. platform with Au1550 and two PCI-devices (custom board)
Debugging:
I digged down to the config_access() of the au1xxx-processors in
arch/mips/pci/ops-au1000.c and switched on DEBUG.
The code of config_access() seems to be almost the same as of the
2.4.x-kernel. But the "pci_cfg_vm->addr" returned by get_vm_area(0x2000, 0)
once on booting is different. That's of course not forbidden. But the
alignment seems to be wrong. In my case, I received:
2.4.31: pci_cfg_vm->addr = c0000000
2.6.18-rc5: pci_cfg_vm->addr = c0101000
To make it short: With 2.6.x it fails on the first config-access with:
"PCI ERR detected: status 83a00356".
Fixup:
My fix is now, to use the VM_IOREMAP-flag in the get_vm_area call. This flag
seems to be introduced in mm/vmalloc.c a long time ago (in 2.6.7-bk13, I
found in gitweb).
Now, the returned address is pci_cfg_vm->addr = c0104000 and everything works
fine.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
[MIPS] Add missing backslashes to macro definitions.
[MIPS] Death list of board support to be removed after 2.6.18.
[MIPS] Remove BSD and Sys V compat data types.
[MIPS] ioc3.h: Uses u8, so include <linux/types.h>.
[MIPS] 74K: Assume it will also have an AR bit in config7
[MIPS] Treat CPUs with AR bit as physically indexed.
[MIPS] Oprofile: Support VSMP on 34K.
[MIPS] MIPS32/MIPS64 S-cache fix and cleanup
[MIPS] excite: PCI makefile needs to use += if it wants a chance to work.
[MIPS] excite: plat_setup -> plat_mem_setup.
[MIPS] au1xxx: export dbdma functions
[MIPS] au1xxx: dbdma, no sleeping under spin_lock
[MIPS] au1xxx: fix PSC_SMBTXRX_RSR.
[MIPS] Early printk for IP27.
[MIPS] Fix handling of 0 length I & D caches.
[MIPS] Typo fixes.
[MIPS] MIPS32/MIPS64 secondary cache management
[MIPS] Fix FIXADDR_TOP for TX39/TX49.
[MIPS] Remove first timer interrupt setup in wrppmc_timer_setup()
[MIPS] Fix configuration of R2 CPU features and multithreading.
...
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for RM200C machines with big endian firmware
Added support for RM200-C40 (R5000 support)
Signed-off-by: Florian Lohoff <flo@rfc822.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support for the GT-64120-based Wind River 4KC PPMC Evaluation board.
Signed-off-by: Rongkai.Zhan <Rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE 1.2.5 and earlier fails to turn on the ExpMemEn bit in the
PCIFeatureControl register, which means that DMA does not work
beyond physical address 01_0000_0000, ergo to DRAM beyond 1GB.
With ExpMemEn turned on, 01_0000_0000-0f_ffff_ffff is mapped,
so DMA works for up to 61 GB of DRAM.
Will be fixed in CFE 1.2.6 (yet to be released).
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PCI support code for PLX 7250 PCI-X tunnel on BCM91480B BigSur board.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
this fixes Lasat pci to work with multi-function devices by assigning
the correct values based on pin number (instead of ignoring them).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thiemo Seufer <ths@networkno.de>
arch/mips/pci/fixup-tb0226.c: In function `pcibios_map_irq':
arch/mips/pci/fixup-tb0226.c:31: warning: implicit declaration of function `vr41xx_set_irq_trigger'
arch/mips/pci/fixup-tb0226.c:32: error: `TRIGGER_LEVEL' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:32: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-tb0226.c:32: error: for each function it appears in.)
arch/mips/pci/fixup-tb0226.c:33: error: `SIGNAL_THROUGH' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:34: warning: implicit declaration of function `vr41xx_set_irq_level'
arch/mips/pci/fixup-tb0226.c:34: error: `LEVEL_LOW' undeclared (first use in this function)
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
