If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.
Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wait until all users have closed their device context before allowing
device unregistration to complete. This prevents a crash caused by
referring to stale data structures.
A better solution would be to have a way to revoke contexts rather
than waiting for userspace to close the context, but that's a much
bigger change that will have to wait. For now let's at least avoid
the crash.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove references to the IPoIB IETF working group as it has been closed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Data corruption has been seen with Mellanox SRP targets when FMRs
create a memory region with I/O virtual address != 0. Add a
workaround that disables FMR merging for Mellanox targets (OUI 0002c9).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Protect against srp_reset_device() clearing the req_queue while
srp_reconnect_target() is in progress (note that state change at
the top of srp_reconnect_target() is not sufficient for this since
srp_reset_device() ignores the state).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Report error code rather than success (0) on failure allocating
timewait_info in ib_send_cm_req().
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define a constant MTHCA_ARRAY_MASK to replace repeated uses of
(PAGE_SIZE / sizeof (void *) - 1) in mthca array code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_array_clear() does not clear the slot if the used count is
positive. This leads to crashes in mthca_qp_event() since that uses
mthca_array_get() to check that the qp is valid.
Discovered by Ali Ayoub.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (24 commits)
Revert "[PATCH] USB: move usb_device_class class devices to be real devices"
Revert "[PATCH] USB: convert usb class devices to real devices"
USB: UHCI: Don't test the Short Packet Detect bit
USB: unusual_devs entry for Nokia 3250
USB: dummy-hcd: disable interrupts during req->complete
USB: fix the USB_GADGET_DUMMY_HCD dependencies
USB: ati_remote.c: autorepeat fix
USB: doc: fixes devio.c location in proc_usb_info.txt.
USB: doc: usb-help.txt update.
USB: Patch for rtl8150 to fix unplug problems
USB: cypress driver comment updates
USB: unusual_devs device removal
usb-storage: Add US_FL_IGNORE_DEVICE flag; ignore ZyXEL G220F
USB: New USB ID for Belkin Serial Adapter
USB: Additional PID for the ftdi_sio driver
USB: adding support for SHARP WS003SH to ipaq.c
USB: Fix Freescale high-speed USB host dependency
USB: Removed 3-port device handler from Option driver
USB: Drop Sierra Wireless MC8755 from the Option driver
USB: Let option driver handle Anydata CDMA modems. Remove anydata driver.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-2.6.18:
gitignore: gitignore quilt's files
kbuild: always use $(CC) for $(call cc-version)
kconfig: correct oldconfig for unset choice options
kbuild: -fno-stack-protector is not good
kbuild: fix typo in modpost
kbuild: improve error from file2alias
kbuild: .gitignore utsrelease.h
kbuild: version.h and new headers_* targets does not require a kernel config
kbuild: hardcode value of YACC&LEX for aic7-triple-x
This reverts c182274ffe commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts bd00949647 commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently some UHCI controllers change the value of the Short Packet
Detect (SPD) bit in the TD status word -- presumably when they receive a
short packet. This patch (as759) changes uhci-hcd to avoid assuming
that the bit is unchanged; in fact, the driver no longer looks at SPD at
all.
This fixes the second problem reported in Bugzilla #6752.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is another unusual_devs entry (as760) for another Nokia device,
this time the 3250.
From: Mario Rettig <mariorettig@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as756) fixes a bug in dummy-hcd found by the lockdep
checker. In one of the code paths, the driver did not disable
interrupts before calling a request completion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB=m, USB_GADGET=y, the option USB_GADGET_DUMMY_HCD mustn't be
offered since selecting it results in a compile error.
This patch fixes kernel Bugzilla #6534 reported by Toralf Frster.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When HZ is set to 250 (new default) or 100, the time span during which
repeated events from the device are ignored could be too small due to
ms->jiffies rounding. This causes the auto repeat to kick in early making
it impossible for the user to generate individual press/release events.
Increate the timeout to compensate.
Signed-off-by: Marko Macek <Marko.Macek@gmx.net>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RTL8150 driver currently crashes the kernel if the USB lead is unplugged
while the device is active. The attached patch adds error handling to
tell the network layer that the device has gone away when the device is
unplugged. With this patch, the device can be plugged and unplugged
to one's hearts' content, without crashing anything.
Oh, I've also added rudimentary suspend and resume methods.
Signed-off-by: Peter Chubb <peter@gelato.unsw.edu.au>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry has been a mystery for some time. I had sent this patch as an
RFC a while ago, and now we've had two reports of this not being needed,
so I'm removing it.
In the event there are reports of breakage, we should revert this patch,
but add a US_FL_NEED_OVERRIDE flag.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.
We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).
The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Can you add the USB IDs for the Belkin USB Serial adapter (P/N F5U257)
to the pl2303 driver in the Linux Kernel? Are you the appropriate person
to approach for this?
I recently purchased a Belkin USB Serial adapter (P/N F5U257) and found
that it didn't work. After a bit of experimentation I found that it
works with the pl2303 driver once the ID has been added. See attached
patch to fix this. Also attached is the output from lsusb -v just in
case you require any information from there.
From: Kim Oldfield <luv@oldfield.wattle.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a short patch which adds one PID to the set of devices
supported by the ftdi_sio driver. The device in question is a
DLP module used as part of a ham radio USB-to-packet adapter.
From: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This small patch enables a support of "SHARP WS003SH".
"SHARP WS003SH" (usullary called "W-ZERO3") is most polular All-in-one handheld
CellPhone-plus-WindowsMobile5.0 in Japan.
"SHARP WS003SH" has two modes, "Modem" and "ActiveSync".
But, "ActiveSync" mode uses NDIS connection.
Therefore, ipaq.c can only support "Modem" mode.
http://www.sharp.co.jp/ws/ (Japanese Site)
http://greggman.com/edit/editheadlines/2005-12-24.htm
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The high-speed USB SOC only exists on MPC834x family not MPC83xx family.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The short driver names were not unique,
which prevented the driver from actually loading.
Also, one of the ioctl pointers was missing.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OHCI updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, OHCI can be a source of system wakeup events
(remote wakeup, device connect/disconnect, etc)
And minor cleanups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UDC updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, UDC can be a source of system wakeup events
(host resume, device connect/disconnect, etc)
- Fix IRQ storming issues, seemingly related to clock disabling
changes that went in a while back
And minor cleanups, especially whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we allow building appletalk drivers in-kernel when
CONFIG_ATALK is modular. That doesn't work because these drivers use
symbols such as "alloc_talkdev" which is exported from code built
by CONFIG_ATALK.
Noticed by Toralf Förster.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4380): Bttv: Revert VBI_OFFSET to previous value, it works better
V4L/DVB (4379): Videodev: Check return value of class_device_register() correctly
V4L/DVB (4373): Correctly handle sysfs error leg file removal in pvrusb2
V4L/DVB (4368): Bttv: use class_device_create_file and handle errors
V4L/DVB (4367): Videodev: Handle class_device related errors
V4L/DVB (4365): OVERLAY flag were enabled by mistake
V4L/DVB (4344): Fix broken dependencies on media Kconfig
V4L/DVB (4343): Fix for compilation without V4L1 or V4L1_COMPAT
V4L/DVB (4342): Fix ext_controls align on 64 bit architectures
V4L/DVB (4341): VIDIOCSMICROCODE were missing on compat_ioctl32
V4L/DVB (4322): Fix dvb-pll autoprobing
V4L/DVB (4311): Fix possible dvb-pll oops
V4L/DVB (4337): Refine dead code elimination in pvrusb2
V4L/DVB (4323): [budget/budget-av/budget-ci/budget-patch drivers] fixed DMA start/stop code
V4L/DVB (4316): Check __must_check warnings
V4L/DVB (4314): Set the Auxiliary Byte when tuning LG H06xF in analog mode
V4L/DVB (4313): Bugfix for keycode calculation on NPG remotes
V4L/DVB (4310): Saa7134: rename dmasound_{init, exit}
V4L/DVB (4306): Support non interlaced capture by default for saa713x
V4L/DVB (4298): Check all __must_check warnings in bttv.
...
When we introduced -rR then aic7xxx no loger could pick up definition
of YACC&LEX from make - so do it explicit now.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Minor comment fix for misc_64.S
[POWERPC] Use H_CEDE on non-SMT
[POWERPC] force 64bit mode in fwnmi handlers to workaround firmware bugs
[POWERPC] PMAC_APM_EMU should depend on ADB_PMU
[POWERPC] Fix new interrupt code (MPIC detection)
[POWERPC] Fix new interrupt code (MPIC endianness)
[POWERPC] Add cpufreq support for Xserve G5
[POWERPC] Xserve G5 thermal control fixes
[POWERPC] Fix mem= handling when the memory limit is > RMO size
[POWERPC] More offb/bootx fixes
[POWERPC] Fix legacy_serial.c error handling on 32 bits
[POWERPC] Fix default clock for udbg_16550
[POWERPC] Fix non-MPIC CHRPs with CONFIG_SMP set
[POWERPC] Fix 32 bits warning in prom_init.c
[POWERPC] Workaround Pegasos incorrect ISA "ranges"
[POWERPC] fix up front-LED Kconfig
Since we now use the generic backlight infrastructure, I think we need to
call rivafb_bl_init before calling register_framebuffer since otherwise
rivafb_bl_init might race with the framebuffer layer already opening the
device and setting up the video mode. In this case we might end up with a
not yet fully intialized backlight (info->bl_dev still NULL) when calling
riva_bl_set_power via rivafb_set_par/rivafb_load_video_mode and the kernel
dies without any further notice during boot.
This fixes booting current git on a PB 6,1. In this case radeonfb/atyfb
would be affected too - I can fix that too but don't have any hardware to
test this on.
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_FB_NVIDIA already depends on CONFIG_PCI in drivers/video/Kconfig.
Driver does an extra ``sanity check'' which is then redundant.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes several problems:
- The legacy backlight value might be set at interrupt time. Introduced
a worker to prevent it from directly calling the backlight code.
- via-pmu allows the backlight to be grabbed, in which case we need to
prevent other kernel code from changing the brightness.
- Don't send PMU requests in via-pmu-backlight when the machine is about
to sleep or waking up.
- More Kconfig fixes.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many IBM Thinkpad T4* models and some R* and X* with radeon video cards draw
too much power when suspended to RAM, reducing drastically the battery
lifetime. The solution is to enable suspend-to-D2 on these machines. They
are whitelisted through their subsystem vendor/device ID. This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=3022
The patch introduces a framework to alter the pm_mode and reinit_func fields
of the radeonfb_info structure based on a whitelist. This should facilitate
future hardware-dependent workarounds. The workaround for the Samsung P35
that is already in the radeonfb code has been rewritten using this framework.
The behavior can be overridden with module options:
i) video=radeonfb:force_sleep=1
enable suspend-to-D2 also on non-whitelisted machines (useful for
testing new notebook models),
ii) video=radeonfb:ignore_devlist=1
Disable checking the whitelist and do not apply any workarounds.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The backlight and lcd subsystems can be notified by the framebuffer layer
of blanking events. However, these subsystems, as a whole, can function
independently from the framebuffer layer. But in order to enable to the
lcd and backlight subsystems, the framebuffer has to be compiled also,
effectively sucking in a huge amount of unneeded code.
To prevent dependency problems, separate out the framebuffer notification
mechanism from the framebuffer layer and permanently link it to the kernel.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The geode hwrng leaks an iomapped resource, if hwrng_register() fails.
This fixes it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The intel hwrng leaks an iomapped resource, if hwrng_register() failes.
This fixes it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
swsusp is unable to suspend my machine (DTK FortisPro TOP-5A notebook) with
kernel 2.6.17.5 because it's unable to suspend PNP device 00:16 (mouse).
The problem is in PNP BIOS. pnp_bus_suspend() calls pnp_stop_dev() for the
device if the device can be disabled according to pnp_can_disable(). The
problem is that pnpbios_disable_resources() returns -EPERM if the device is
not dynamic (!pnpbios_is_dynamic()) but insert_device() happily sets
PNP_DISABLE capability/flag even if the device is not dynamic. So we try
to disable non-dynamic devices which will fail. This patch prevents
insert_device() from setting PNP_DISABLE if the device is not dynamic and
fixes suspend on my system.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
