MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.
BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using | with a constant is always true.
Likely this should have be &.
cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Cc: stable@kernel.org
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of hardware reconfig mac80211 tries
to restore the station state to its values
before the hardware reconfig, but it only
goes to the last-state - 1. Fix this
off-by-one error.
Cc: stable@kernel.org [3.4]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since my commit
iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.
Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh station that joins an MBSS is reachable using mesh portal with 6
address frame by mesh stations from another MBSS if these two different
MBSSes are bridged. However, if the mesh station later moves into the
same MBSS of those mesh stations, it is unreachable by mesh stations
in the MBSS due to the mpp_paths table is not deleted. A quick fix
is to perform mesh_path_lookup, if it is available for the target
destination, mpp_path_lookup is not performed. When the mesh station
moves back to its original MBSS, the mesh_paths will be deleted once
expired. So, it will be reachable using mpp_path_lookup again.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CFG80211_DEV_WARN_ON() at "net/wireless/ibss.c line 63"
is unnecessarily triggered even after successful connection,
when cfg80211_ibss_joined() is called by driver inside
.join_ibss handler.
This patch fixes the problem by changing 'sme_state' in ibss path
and having WARN_ON() check for 'sme_state' similar to infra
association.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 133d40f9a2
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Wed Mar 28 16:01:19 2012 +0200
mac80211: do not scan and monitor connection in parallel
add bug, which make possible to start a scan and never finish it, so
make every new scanning request finish with -EBUSY error. This can
happen on code paths where we finish connection monitoring and clear
IEEE80211_STA_*_POLL flags, but do not check if scan was deferred.
This patch fixes those code paths.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes two useless initialisations in the
stmmac_rx and stmmac_tx functions.
In the former, the count variable was reset twice and in
the stmmac_tx we only need to increment the dirty pointer
w/o setting the entry variable.
v2: review the subject and comment that was not clear in my
first version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit that removed unnecessary casts of pointers
to the same type uncovered a missing __force cast.
Add it.
Reported by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the busy-waiting/udelay to wait_event on outstanding sends.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drop_monitor calls several sleeping functions while in atomic context.
BUG: sleeping function called from invalid context at mm/slub.c:943
in_atomic(): 1, irqs_disabled(): 0, pid: 2103, name: kworker/0:2
Pid: 2103, comm: kworker/0:2 Not tainted 3.5.0-rc1+ #55
Call Trace:
[<ffffffff810697ca>] __might_sleep+0xca/0xf0
[<ffffffff811345a3>] kmem_cache_alloc_node+0x1b3/0x1c0
[<ffffffff8105578c>] ? queue_delayed_work_on+0x11c/0x130
[<ffffffff815343fb>] __alloc_skb+0x4b/0x230
[<ffffffffa00b0360>] ? reset_per_cpu_data+0x160/0x160 [drop_monitor]
[<ffffffffa00b022f>] reset_per_cpu_data+0x2f/0x160 [drop_monitor]
[<ffffffffa00b03ab>] send_dm_alert+0x4b/0xb0 [drop_monitor]
[<ffffffff810568e0>] process_one_work+0x130/0x4c0
[<ffffffff81058249>] worker_thread+0x159/0x360
[<ffffffff810580f0>] ? manage_workers.isra.27+0x240/0x240
[<ffffffff8105d403>] kthread+0x93/0xa0
[<ffffffff816be6d4>] kernel_thread_helper+0x4/0x10
[<ffffffff8105d370>] ? kthread_freezable_should_stop+0x80/0x80
[<ffffffff816be6d0>] ? gs_change+0xb/0xb
Rework the logic to call the sleeping functions in right context.
Use standard timer/workqueue api to let system chose any cpu to perform
the allocation and netlink send.
Also avoid a loop if reset_per_cpu_data() cannot allocate memory :
use mod_timer() to wait 1/10 second before next try.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding socket backlog len in INET_DIAG_SKMEMINFO is really useful to
diagnose various TCP problems.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some dropwatch/drop_monitor false positives.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_make_synack() clones the dst, and callers release it.
We can avoid two atomic operations per SYNACK if tcp_make_synack()
consumes dst instead of cloning it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no value using sock_wmalloc() in tcp_make_synack().
A listener socket only sends SYNACK packets, they are not queued in a
socket queue, only in Qdisc and device layers, so the number of in
flight packets is limited in these layers. We used sock_wmalloc() with
the %force parameter set to 1 to ignore socket limits anyway.
This patch removes two atomic operations per SYNACK packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wCpY
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb
ii) Migration of thin devices from one pool to another.
iii) Merging snapshots back into an external origin.
iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull networking updates from David Miller:
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:
- EFI boot stub documentation and the ability to print error messages;
- Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
should never have been ported, and the port is broken and
potentially dangerous.)
- ftrace stack corruption fixes. I'm not super-happy about the
technical implementation, but it is probably the least invasive in
the short term. In the future I would like a single method for
nesting the debug stack, however."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
x86, efi: Add EFI boot stub documentation
x86, efi; Add EFI boot stub console support
x86, efi: Only close open files in error path
ftrace/x86: Do not change stacks in DEBUG when calling lockdep
x86: Allow nesting of the debug stack IDT setting
x86: Reset the debug_stack update counter
ftrace: Use breakpoint method to update ftrace caller
ftrace: Synchronize variable setting with breakpoints
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39b ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d3108 - tty: add lockdep annotations
8f6576ad47 - tty: fix ldisc lock inversion trace
d3ca8b64b9 - pty: Fix lock inversion
b1d679afd7 - tty: drop the pty lock during hangup
abcefe5fc3 - tty/amiserial: Add missing argument for tty_unlock()
fd11b42e35 - cris: fix missing tty arg in wait_event_interruptible_tty call
d29f3ef39b - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fix and a fix from the signal changes for frv from Al Viro.
The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short". Al didn't notice, and
made both of them be the unsigned short.
The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
powerpc: Fix size of st_nlink on 64bit
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
frv: Remove bogus closing parenthesis
commit e57f93cc53 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduced by commit 6fd84c0831
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge fixups for the mac NLS tables from Andrew.
* emailed from Andrew Morton, and one cleanup by me:
nls: fix (and rename) mac NLS table files and config options
fs/nls/Makefile: remove bogus CONFIG_ assignments
The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).
And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".
So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These were debug things which snuck through.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>