commit 8de66b0e6a56ff10dd00d2b0f2ae52e300178587 upstream.
The system can hit a deadlock if an xhci adapter breaks while initializing.
The deadlock is between two threads: thread 1 is tearing down the
adapter and is stuck in usb_unlocked_disable_lpm waiting to lock the
hcd->handwidth_mutex. Thread 2 is holding this mutex (while still trying
to add a usb device), but is stuck in xhci_endpoint_reset waiting for a
stop or config command to complete. A reboot is required to resolve.
It turns out when calling xhci_queue_stop_endpoint and
xhci_queue_configure_endpoint in xhci_endpoint_reset, the return code is
not checked for errors. If the timing is right and the adapter dies just
before either of these commands get issued, we hang indefinitely waiting
for a completion on a command that didn't get issued.
This wasn't a problem before the following fix because we didn't send
commands in xhci_endpoint_reset:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
With the patch I am submitting, a duration test which breaks adapters
during initialization (and which deadlocks with the standard kernel) runs
without issue.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Torez Smith <torez@redhat.com>
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Signed-off-by: Torez Smith <torez@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-7-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a70bcbc322837eda1ab5994d12db941dc9733a7d upstream.
NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.
[Minor changes to comment and commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47f50d61076523e1a0d5a070062c2311320eeca8 upstream.
Early xHCI 1.1 spec did not mention USB 3.1 capable hosts should set
sbrn to 0x31, or that the minor revision is a two digit BCD
containing minor and sub-minor numbers.
This was later clarified in xHCI 1.2.
Some USB 3.1 capable hosts therefore have sbrn set to 0x30, or minor
revision set to 0x1 instead of 0x10.
Detect the USB 3.1 capability correctly for these hosts as well
Fixes: ddd57980a0fd ("xhci: detect USB 3.2 capable host controllers correctly")
Cc: <stable@vger.kernel.org> # v4.18+
Cc: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream.
If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.
Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream.
If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.
Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED
While at it fix the split line error message
Tested-by: Jan Schmidt <jan@centricular.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8c3b718087bf7c3c8e388eb1f72ac1108a4926e upstream.
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddd57980a0fde30f7b5d14b888a2cc84d01610e8 upstream.
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7fac17ca925faa03fc5eb854c081a24075f8bad upstream.
Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.
Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.
[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream.
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f068090426ea8d72c408ebd42953a82a88e2282c upstream.
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d6 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d6 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the cancelled URB is on the current endpoint ring.
If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.
Don't try to stop the ring. It would be useless.
This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.
Cc: <stable@vger.kernel.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If td_list is not empty the cfg_cmd will not be freed,
call xhci_free_command to free it.
Signed-off-by: Zheng Xiaowei <zhengxiaowei@ruijie.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the xhci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some controllers take almost 55ms to complete controller
restore state (CRS).
There is no timeout limit mentioned in xhci specification so
fixing the issue by increasing the timeout limit to 100ms
[reformat code comment -Mathias]
Signed-off-by: Ajay Gupta <ajaykuee@gmail.com>
Signed-off-by: Nagaraj Annaiah <naga.annaiah@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas controllers get into a weird state if they are reset while
programmed with 64bit addresses (they will preserve the top half of the
address in internal, non visible registers).
You end up with half the address coming from the kernel, and the other
half coming from the firmware.
Also, changing the programming leads to extra accesses even if the
controller is supposed to be halted. The controller ends up with a fatal
fault, and is then ripe for being properly reset. On the flip side,
this is completely unsafe if the defvice isn't behind an IOMMU, so
we have to make sure that this is the case. Can you say "broken"?
This is an alternative method to the one introduced in 8466489ef5
("xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"),
which will subsequently be removed.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have 32 different quirks, and the field that holds them
is full. Let's bump it up to the next stage so that we can handle
some more... The type is now an unsigned long long, which is 64bit
on most architectures.
We take this opportunity to change the quirks from using (1 << x)
to BIT_ULL(x).
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get rid of port iomem arrays and use port structures in the following
functions:
xhci_find_raw_port_number()
xhci_disable_port_wake_on_bits()
xhci_set_usb2_hardware_lpm()
xhci_all_ports_seen_u0()
compliance_mode_recovery()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows us to know the correct hcd a xhci roothub and its ports
belong to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e
where xhci_free_virt_device() sets slot id to 0 if udev exists:
if (dev->udev && dev->udev->slot_id)
dev->udev->slot_id = 0;
dev->udev will be true even if udev is freed because dev->udev is
not set to NULL.
set dev->udev pointer to NULL in xhci_free_dev()
The original patch went to stable so this fix needs to be applied
there as well.
Fixes: a400efe455 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver displays the supported xHC USB revision in a message during
driver load:
"Host supports USB 3.1 Enhanced SuperSpeed"
Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts
Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.
xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.
This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.
Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function xhci_stop, xhci_debugfs_exit called before xhci_mem_cleanup.
xhci_debugfs_exit removed the xhci debugfs root nodes, xhci_mem_cleanup
called function xhci_free_virt_devices_depth_first which in turn called
function xhci_debugfs_remove_slot.
Function xhci_debugfs_remove_slot removed the nodes for devices, the nodes
folders are sub folder of xhci debugfs.
It is unreasonable to remove xhci debugfs root folder before
xhci debugfs sub folder. Function xhci_mem_cleanup should be called
before function xhci_debugfs_exit.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug after plugged out USB device, the device and its ep00
nodes are still kept, we need to remove the nodes in xhci_free_dev when
USB device is plugged out.
Fixes: 052f71e25a ("xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system resume from hibernation, xhci host is reset, all the
nodes in devices folder are removed in xhci_mem_cleanup function.
Later nodes in /sys/kernel/debug/usb/xhci/* are created again in
function xhci_run, but the nodes already exist, so the nodes still
keep the old ones, finally device nodes in xhci debugfs folder
/sys/kernel/debug/usb/xhci/*/devices/* are disappeared.
This fix removed xhci debugfs nodes before the nodes are re-created,
so all the nodes in xhci debugfs can be re-created successfully.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Reported-by: Alexander Kappner <agk@godking.net>
Tested-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver currently has the IMOD set to 160, which
translates to an IMOD interval of 40,000ns (160 * 250)ns
Commit 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
introduced a QUIRK for the MTK platform to adjust this interval to 20,
which translates to an IMOD interval of 5,000ns (20 * 250)ns. This is
due to the fact that the MTK controller IMOD interval is 8 times
as much as defined in xHCI spec.
Instead of adding more quirk bits for additional platforms, this patch
introduces the ability for vendors to set the IMOD_INTERVAL as is
optimal for their platform. By using device_property_read_u32() on
"imod-interval-ns", the IMOD INTERVAL can be specified in nano seconds.
If no interval is specified, the default of 40,000ns (IMOD=160) will be
used.
No bounds checking has been implemented due to the fact that a vendor
may have violated the spec and would need to specify a value outside of
the max 8,000 IRQs/second limit specified in the xHCI spec.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each event segment has been exposed through debugfs. There is no
need to dump ERST content with printk in code. Remove it to make
code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The content of each register has been exposed through debugfs.
There is no need to dump register content with printk in code
lines. Remove them to make code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
can be implemented with the Debug Capability(DbC). It presents a debug
device which is fully compliant with the USB framework and provides the
equivalent of a very high performance full-duplex serial link. The debug
capability operation model and registers interface are defined in 7.6.8
of the xHCI specification, revision 1.1.
The DbC debug device shares a root port with the xHCI host. By default,
the debug capability is disabled and the root port is assigned to xHCI.
When the DbC is enabled, the root port will be assigned to the DbC debug
device, and the xHCI sees nothing on this port. This implementation uses
a sysfs node named <dbc> under the xHCI device to manage the enabling
and disabling of the debug capability.
When the debug capability is enabled, it will present a debug device
through the debug port. This debug device is fully compliant with the
USB3 framework, and it can be enumerated by a debug host on the other
end of the USB link. As soon as the debug device is configured, a TTY
serial device named /dev/ttyDBC0 will be created.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a xhci_alloc_command_with_ctx() helper to get rid of
one of the boolean parameters telling if a context should
be allocated with the command.
No functional changes, improves core readability
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning: variable 'ep' set but not used
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning about variable 'last_freed_endpoint'
set but not used [-Wunused-but-set-variable]
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>