snd_soc_dapm_new_widgets will call dapm_power_widgets at
the end, so there is no need to call snd_soc_dapm_sync
after snd_soc_dapm_new_widgets.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Reviewed-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
WM8750 address is 0x1b, not 0x1a. Without this fix ALSA detects no sound
cards on Zipit
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix jack detection on Zipit Z2, otherwise it
disables headphones output when jack is connected
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While I2S/TDM/AC97 DAI is built-in, others are compiled as modules,
SND_BF5XX_SOC_SPORT will be module, then DAI can't get some symbols.
Except that, SND_BF5XX_AC97 depends on SND_BF5XX_SOC_AC97 too.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't want to use internal frame syncs otherwise we sometimes
get out of sync, so don't enable them when setting up the SPORT.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to tweak how we query the active capture/playback state after
the recent overhauls of common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
One spot was missed in this driver when converting from
snd_soc_dai.private_data to snd_soc_dai_get_drvdata.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix initialization for HP 2011 notebooks
ALSA: hda - Add support for VMware controller
ALSA: hda - consitify string arrays
ALSA: hda - Add add multi-streaming playback for AD1988
ASoC: EP93xx: fixed LRCLK rate and DMA oper. in I2S code
ASoC: WM8990: msleep() takes milliseconds not jiffies
ALSA : au88x0 - Limit number of channels to fix Oops via OSS emu
ALSA: constify functions in ac97
ASoC: WL1273 FM radio: Fix breakage with MFD API changes
ALSA: hda - More coverage for odd-number channels elimination for HDMI
ALSA: hda - Store PCM parameters properly in HDMI open callback
ALSA: hda - Rearrange fixup struct in patch_realtek.c
ALSA: oxygen: Xonar DG: fix CS4245 register writes
ALSA: hda - Suppress the odd number of channels for HDMI
ALSA: hda - Add fixup-call in init callback
ALSA: hda - Reorganize fixup structure for Realtek
ALSA: hda - Apply Sony VAIO hweq fixup only once
ALSA: hda - Apply mario fixup only once
ALSA: hda - Remove unused fixup entry for ALC262
Fixes for HP 2011 notebooks: enable dock ports and disable BTL
initialization in the driver.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the new PCI ID 0x15ad and device ID 0x1977 for VMware HDAudio
Controller.
[changed to use AZX_DRIVER_GENERIC by tiwai]
Signed-off-by: Bankim Bhavsar <bbhavsar@vmware.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attached a patch which add a new model to support multi-streaming
playback for ad1988.
playback another stereo stream through the front panel headphone on
device 2 while playback through the speakers connected to rear panel
on device 0 at the same time.
Tested with ad1988a rev2 codec on asus P5B-V motherboard.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changelog:
1. I2S module of EP93xx should be feed by 32bit DMA transfers. This is
hardware limitation and that's the way original Cirrus's driver worked.
This will fix distorted sound playback and make capture actually work in
present ep93xx drivers.
I've found, that author of code, on which modern ep93xx-i2s.c and
ep93xx-pcm.c are based, had faced this problem also in 2007:
http://blog.gmane.org/gmane.linux.ports.arm.cirrus/month=20070101/page=3
Now SoC code uses his developments, but not overcomes the hardware
issues. Some details from EP93xx users guide:
Both I2S transmitter and receiver have similar 16x32bit FIFO, where they
store 8 samples for both left and right channels. The FIFO is always
32bit wide and should be properly aligned if you use samples of other
width. Transmitter and receiver have configuration registers for
selection of I2S word length (16, 24, 32). They are I2STXWrdLen and
I2SRXWrdLen.
Yes, EP93xx DMA can do byte, word and quad-word transfers. The width for
transfers to and from peripherals is selected by particular module
configuration. Lucky AC97 module has such configuration: AC97RXCRx
registers, bit CM (Compact mode enable) switches between 16 and 32 bit
samples. AC97TXCRx registers have the same bits for transmitters.
ep93xx-ac97.c enables this compact mode and so has all the rights to use
S16_LE format.
No one has found such a configuration in I2S module until now in any
Cirrus manuals. I2S module always feeds it's 32bit wide FIFO with 32bit
samples consecutively for left and right channels. You cannot use 32-bit
DMA transfers to transfer two 16-bit samples.
So we can use two formats for AC97, but should remove all but S32_LE for
I2S. Always using 32 bit chunks is not a problem for I2S, the codec I
use uses less bits too (24), it's permitted by I2S standard.
In proposed patch formats list shortened to just S32_LE, this makes all
the DMA transactions right, while ALSA will do all sample format
translation for us.
2. Incorrect setting of LRCLK (2 times slower) in original ep93xx-i2s.c
masks the first problem.
DMA takes two 16 bit samples instead of one, overall sound speed seems
to be normal, but you get actually 4000 sampling rate instead of
requested 8000 and therefore some noise... This is also the reason why
the capture function not worked at all in this driver...
If we take a look into I2S specification, we will figure that LRCLK MUST
be equal to sample rate, if we are talking about stereo (in mono too,
but it's not our case at all).
In proposed patch SCLK and LRCLK rates are corrected, assuming we always
send 32 bits * 2 channels to codec.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Directly accessing the register cache means that we can't use anything
except a flat register cache so use snd_soc_update_bits().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8991 is a highly integrated ultra-low power hi-fi CODEC designed for
handsets rich in multimedia features such as GPS, mobile TV, digital audio
playback and gaming.
This driver was originally written by Graeme Gregory and has been maintained
out of tree by Mark Brown and Dimitris Papastamos.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The machine driver can't register the card directly and need to do this thru
soc-audio device creation
This patch allows the register and unregister card to be directly called by
machine drivers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix playback/capture channels patch to change supported playback
channels of au8830 to 1,2,4 and capture channels to 1,2.
This prevent oops when oss emulation use SNDCTL_DSP_CHANNELS to
set 3 Channels
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
With this change, I can capture from a microphone plugged into the
mic jack on Harmony (after unmuting Left Input PGA, and maybe turning
up the gain there too).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
That config variable doesn't exist in the mainline kernel, and hence
the dependency shouldn't either.
In linux-tegra-2.6.36, the dependency did exist to avoid a conflict with
the old non-ALSA Tegra I2S driver. However, this isn't and won't be
upstreamed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These changes are needed to keep up with the changes in the
MFD core and V4L2 parts of the wl1273 FM radio driver.
Use function pointers instead of exported functions for I2C IO.
Also move all preprocessor constants from the wl1273.h to
include/linux/mfd/wl1273-core.h.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit ad09fc9d21 didn't cover the
case for Intel and Nvidia HDMIs, where hdmi_pcm_open() is called.
Put the hw_constraint there, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In hdmi_pcm_open(), the evaluated PCM hw parameters are stored in
hinfo, but these aren't properly set back to the current runtime
record since these have been set beforehand in azx_pcm_open().
This patch fixes the behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It looks like that HDMI codecs don't support the odd number of channels
although HD-audio spec doesn't have the restriction. Add the
hw_constraint to limit to only the even number of channels.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the soc_probe initializes the card hence it does the card list
initialzation. But if machines directly register the card they would need to
do these steps, so putting them as inline would save lot of code
This patch adds an inline to do list initialzation
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <harsha.priya@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The card debugfs initialization is done in soc_probe but would be better if it
is done when the card in registered
This patch moves the debugfs initialization to register_card()
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <harsha.priya@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In soc_remove() the card resources are cleaned up.
This can also be done in card_unregister()
This patch move this cleanup into a new function and calls it from
card_unregister. This paves way for further work to allow card registartion
from machine.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some cases, the fix-up is required in the init callback to be called
both at the first initialization and at the resume. The new action type
ALC_FIXUP_ACT_INIT is used for this case.
So far, only ALC275_FIXUP_SONY_HWEQ uses this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of keeping various data types in a single record, put the
type field and keep a single value in each entry, but allows chaining
multiple fixup entries. This allows more flexible data management
(see ALC275_FIXUP_SONY_HWEQ for example).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A recent discussion on linux-arm-kernel noted that the value returned by
clk_get_sys is an opaque token, and not strictly a pointer; it is
meaningful only to the clock API, clients should not dereference the value,
and the clock API must accept any non-IS_ERR value it returned.
Hence, only IS_ERR is appropriate to interpret the result, not
IS_ERR_OR_NULL.
I checked that clk_get_sys in both ASoC's for-next and Tegra's for-next
do behave as described; NULL is not returned in the case of error.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that all calls to readable_register()/volatile_register() go via
the snd_soc_codec function pointers.
If the default register access table has been given but no functions
for handling readable()/volatile() registers, use the default ones provided
by soc-cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For common scenarios, device drivers can provide a table of all the
registers that are at least either readable/writable/volatile. The idea
is that if a register lookup fails, all of its read/write/vol members
will be zero and will be treated as default. This also reduces the
size of the register access array.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When only one mic is available and it's an analog mic, the current
IDT/STAC parser may give an Oops.
Reference: bko#25692
https://bugzilla.kernel.org/show_bug.cgi?id=25692
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Simplify the use of reg_size, by calculating it once and storing it in
the codec structure for later reference. The value of reg_size is
reg_cache_size * reg_word_size.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the addition of the cache fallback functionality, it is necessary
to ensure that if the register defaults cache was marked as __devinitconst
and the LZO compression is not compiled in the kernel, the fallback to
flat compression will still use a copy of the defaults cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With GPIO2-fixup, another fixup for NID 0x19 was missing because the
fixup is applied only once. Add the corresponding verb to the entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
SONY VAIO ALC275 default BIOS verb set the hardware EQ to disable.
Enable it when driver is loading.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo NB 0x9e54 use the external AMP in an inverted manner.
Set EAPD to low will enable the AMP.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added hardware constraint in patch_hdmi.c to disable
channels 4/6 which are not supported by some older
NVIDIA GPUs.
Signed-off-by: Nitin Daga <ndaga@nvidia.com>
Acked-By: Stephen Warren <swarren@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dynamic PCM restriction based on ELD information may lead to the
problem in some cases, e.g. when the receiver is turned off. Then it
may send a TV HDMI default such as channels = 2. Since it's still
plugged, the driver doesn't know whether it's the right configuration
for future use. Now, when an app opens the device at this moment,
then turn on the receiver, the app still sends channels=2.
The right solution is to implement some kind of notification and
automatic re-open mechanism. But, this is a goal far ahead.
This patch provides a workaround for such a case by providing a new
module option static_hdmi_pcm for snd-hda-codec-hdmi module. When
this is set to true, the driver doesn't change PCM parameters per
ELD information. For users who need the static configuration like
the scenario above, set this to true.
The parameter can be changed dynamically via sysfs, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
sound/soc/codecs/tpa6130a2.c: In function 'tpa6130a2_add_controls':
sound/soc/codecs/tpa6130a2.c:342: warning: unused variable 'dapm'
Introduced by commit 39646871a4 ("ASoC:
tpa6130a2: Replace DAPM code with direct interface").
The DAPM code has been removed from the driver, but the
dapm struct remained.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The L/R LOM line can be invertined side of the
corresponding DAC, or inverted from the corresponding
LOP.
Add control for user space to select the source of the
LOM inversion.
When only the analog bypass is enabled, and the LOM
is inverted from DAC output, we need to power the
corresponding DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This codec is to be used by the DMIC driver to
control the DMIC codec. This driver will be used on future
implementations of the DMIC driver to support codec specific
features.
At this time, the codec driver just registers the codec DAI.
Signed-off-by: David Lambert <dlambert@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix missing NULL checks in usb_stream_hwdep_poll() and usb_stream_hwdep_ioctl().
Wake up poll waiters before returning from usb_stream_hwdep_ioctl().
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The US-122L always reads 9 bytes per urb unless they are set to 0xFD.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use Takashi's clean up code to make the cache manipulation code more
readable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The size of the lzo syncing bitmap was incorrectly set to the size
of the cache times the word size, however, the correct size is the
size of the cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a mixer control to switch between the optical and coaxial S/PDIF
inputs on the HT-Omega Claro and Claro halo cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable the X-Meridian's CD input and the X-Meridian 2G's potential
MIDI ports.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch remove including unnecessary/duplicated headers which relative
with Samsung SoCs.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update snd_soc_update_bits() so that it returns a negative error code if the
the read or write operation fails.
Note that currently, a lot of the lower-level read functions have an unsigned
integer return type (and some of them even try to return a negative number),
but this code still appears to work in those cases.
An examination of the code shows that all current callers are compatible with
this change.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Few funtions can be modularized in this driver to make them look cleaner
like managing the stream status with locks and filling pcm parameters.
This patch adds helper functions to do the same.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 6d803ba736 "ARM: 6483/1: arm & sh:
factorised duplicated clkdev.c" broke compilation of migor audio. Use the
correct header to fix the problem.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the CS4270 driver to use ASoC's internal codec register cache feature.
This change allows ASoC to perform the low-level I2C operations necessary to
read the register cache. Support is also added for initializing the register
cache with an array of known power-on default values.
The CS4270 driver was handling the register cache itself, but somwhere along
the conversion to multi-compaonent, this feature broke.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Everything else is using snd_soc_ so we should use it here too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many portions of Tegra ASoC machine drivers will be similar or identical.
To avoid cut/paste, this file will act as a repository for all that common
code. For now, it solely includes code to reprogram the audio PLL for
44.1KHz- vs. 48KHz-based sample rates.
Signed-Off-By: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This provides an ASoC DAI interface for Tegra's I2S controller.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This provides an ASoC platform driver that manages Tegra's APB DMA
controller.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAS (Digital Audio Switch) is a mux/crossbar which sits between
the DACs (Digital Audio Controllers) and the DAPs (Digital Audio
Ports). Audio data may be routed between DACs and DAPs in various
combinations as required by board design/application.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A couple Tegra ASoC drivers will create debugfs entries. Mark requested
these by under debugfs/asoc/ not just debugfs/. To enable this, export
the dentry representing debugfs/asoc/.
Also, rename debugfs_root -> asoc_debugfs_root now it's exported to
prevent potential symbol name clashes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The infrastructure for handling NULL default register maps is already
included in the soc-cache code, just ensure that we don't try to dereference
a NULL pointer while accessing a NULL register cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of the generic Oxygen, use the actual card name, if known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apparently, the revision is 2 on all sold sound cards, so this
information is not actually useful.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control to select between the on-board and extension board
S/PDIF inputs for the X-Meridian (2G).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control to prevent capturing S/PDIF samples that are not
marked as valid (non-audio or corrupted samples).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the 24-bit audio I/Os of the Edirol SD-90 interface.
Reported-any-tested-by: Jim Grusendorf <alsa-user@grusendorf.ca>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify info callbacks by using the snd_ctl_enum_info() helper function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify the info callback by using the snd_ctl_enum_info() helper function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify info callbacks by using the snd_ctl_enum_info() helper function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify the info callback by using the snd_ctl_enum_info() helper function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce the helper function snd_ctl_enum_info() to fill out the
elem_info fields for an enumerated control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add experimental support for the Asus Xonar HDAV1.3 Slim sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add experimental support for the Asus Xonar DG sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the AuzenTech X-Meridian 7.1 2G sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the CSxxxx and AKxxxx DAC/ADC chips, the MCLK factor in double rate
modes (64-96 kHz) can be reduced to 128x without reducing sound quality.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the get_i2s_mclk callback with tables of MCLK values. This
simplifies the MCLK-handling code in both the framework and the model-
specific drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not apply the headphone gain offset to any but the front DAC. These
DACs would not be used in headphone mode, so this saves a few register
writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the DAC Oversampling mixer control because this setting does not
make much sense.
For cards with the H6 daughterboard, 128x oversampling was disabled
anyway because these high MCLK frequency would not be compatible with
the connector cable.
For cards without the H6 daughterboard, 128x gives a slightly higher
output quality; there is no reason to reduce it to 64x except for saving
power, but then these cards have not been designed to be power efficient
anyway (the D2's blinkenlights cannot be disabled).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because of the unshielded connector cable, it is important to use as low
a master clock frequency as possible with the H6.
For double rate modes (64-96 kHz), the MCLK rate is unconditionally
lowered from 512x to 256x because the higher rate would not improve
anything.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The clock output of the CS2000, which is used as master clock for the
DACs, was using half the actual master clock frequency for some reason.
Using the theoretically correct frequency seems also to work in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Xonar Essence ST Deluxe, remove all mixer controls that would
require I2C communication with the third DAC, which does not work
because of an addressing conflict with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCM format used for the PCM1796 from left-justified to I2S to
ensure that the correct format is used even for the Essence ST Deluxe's
center/LFE DAC, where I2C does not work because of an address conflict
with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM1796 needs the master clock for I2C communication to work, so
add delays after clock changes to ensure that the clock is stable when
we try to write the DACs' registers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To make the I2C communication reliable when using the H6 daughterboard,
reduce the I2C clock frequency.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix wrong register bits for SPI clock cycle times longer than 160 ns,
and adjust the polling loop timeout for these speeds.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of DACs can now be deduced from the dac_channels_mixer field,
so the private_data field is no longer needed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For cards like the Xonar HDAV1.3, differentiate between the number of
PCM channels that can be played and the number of channels whose volume
can be adjusted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, Realtek auto-parser assumed that the multiple pins are only for
line-outs, and assigned the channel names like Front, Surround, etc for
the multiple outputs. But, there are devices that have multiple
headphones, and these can be better controlled with the corresponding
control-name like "Headphone" with indicies.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When multiple headphone pins are defined without line-out pins, the
driver takes them as primary outputs. But it forgot to set line_out_type
to HP by assuming there is some rest of HP pins. This results in some
mis-handling of these pins for Realtek codec parser. It takes as if
these are pure line-out jacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Enable Mic Jack during glue driver init, otherwise capture will not work.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since direct register writes may confuse the drivers and are supposed
to be used only in diagnostic situations discourage their use in
production by tainting the kernel when we do a write.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch moves PCM specific definitions, they doesn't need to be
shared, into 'pcm.c' from 'pcm.h'.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch moves DMA specific definitions, they doesn't need to be
shared, into 'dma.c' from 'dma.h'. And remove unnecessery definitions
on 'dma.h'.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch moves AC97 specific definitions, they doesn't need to be shared,
into 'ac97.c' from 'ac97.h'. This patch also remove header file, 'ac97.h',
and remove includes on machine drivers.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
previous commit e62255f2ad introduced DDEBUG flag in Makefile
This causes all debug statemenets to be ON.
This patch removes this flag
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
this patch fixes the style inconsistency by removing empty space in MODULE_ALIAS
also removes a redundant return statement
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
this patch fixes inconsistencies commented by Mark.
This also fixes few other style things in audio_map & header file
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_pcm_hw_param_near() will leak the memory allocated to 'save' if the
call to snd_pcm_hw_param_max() returns less than zero.
This patch makes sure we never leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugtrack.alsa-project.org/alsa-bug/view.php?id=5184
A user reported on the alsa-devel mailing list that he needs to use
the vostro model quirk to have audible playback, so apply it for his
PCI SSID.
Reported-and-tested-by: Fernando Lemos <fernandotcl@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://bugs.launchpad.net/bugs/689036
Many new Lenovos need the ideapad quirk. Also, since the
auto parser for this chip is far from optimal, the regression
risk is low (although not zero).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If more than one mic is present with different locations,
e g "Front Mic" and "Rear Mic", they can use the same index (0),
since their names are different.
Previous behavior was to have "Front Mic" as index 1, causing it
to be ignored by e g PulseAudio.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://bugs.launchpad.net/bugs/697240
If the "Volume" suffix is not given, alsa-lib gets confused and
loses the dB information at the simple element level.
Boosts generally affects both playback and capture, as they are
applied early in the chain. Hence no "Playback" or "Capture" in
the suffix.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://bugs.launchpad.net/bugs/696493
According to datasheet (and real-world testing), IDT 92HD88B can
have internal mics at NID 0x11 and 0x20, so enable them accordingly.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
This patch adds the makefile and kconfig changes for mid asoc drivers:
platform and machine driver which are introduced in 2 preceeding patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the medfield machine driver
Machine driver glues the sn95031 codec driver and sst_platform driver to form the asoc sound driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the platform driver for mid asoc drivers. This platfrom
driver sends commands to sst dsp engine driver for the dai operations.
For this purpose it depends on intel_sst driver which is currently in
staging tree
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the sn95031 asoc codec driver. This driver currently
supports only playback. Capture and jack detection to be added later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The soc-core takes the platform and codec driver reference during probe. Few of
these references are not released during remove. This cause the platform and
codec driver module unload to fail.
This patch fixes by the taking only one reference to platform and codec module
during probe and releases them correctly during remove. This allows load/unload
properly
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After multi-component conversion these machine drivers don't actually need
anything from sound/soc/codecs/tlv320aic3x.h so don't include it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The rest of ASoC is using SND_SOC_ as the prefix for all the Kconfig
symbols so do so for the new Samsung drivers too, rather than using
ASOC_ as they currently are.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Instead of replacing 'milisec' by 'millisec', I decided to use
the more common SI unit. Other drivers use 'milliseconds'
or 'ms', too ('millisec' is never used).
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- much improved implementation due to clean codec hierarchy
- preparation for potential per-codec spinlock change
NOTE: additionally removes a chip->pcm[codec_type] NULL ptr check
(due to it requiring access to external chip struct),
however I believe this to be ok since this condition should not occur
and most drivers don't check against that either.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- use a separate variable for the frequency part, don't always "or" it
- use a "clever"(?) macro to shorten the code
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- correct samples to be POSIX shell compatible
- add logging of jiffies value in _pointer()
- several comments
- cleanup
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sjoerd Simons reports that, without using position_fix=1, recording
experiences overruns. Work around that by applying the LPIB quirk
for his hardware.
Reported-and-tested-by: Sjoerd Simons <sjoerd@debian.org>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The load_mixer_volumes() function, which can be triggered by
unprivileged users via the SOUND_MIXER_SETLEVELS ioctl, is vulnerable to
a buffer overflow. Because the provided "name" argument isn't
guaranteed to be NULL terminated at the expected 32 bytes, it's possible
to overflow past the end of the last element in the mixer_vols array.
Further exploitation can result in an arbitrary kernel write (via
subsequent calls to load_mixer_volumes()) leading to privilege
escalation, or arbitrary kernel reads via get_mixer_levels(). In
addition, the strcmp() may leak bytes beyond the mixer_vols array.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but there are quite a few drivers left which now have an unused reg_cache field in
their private device struct.
This patch removes these unused fields.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8753 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Furthermore the generic cache uses zero-based numbering while the wm8753 cache
uses one-based numbering.
Thus we end up with two from each other incoherent caches, which leads to undefined
behaviour and crashes.
This patch fixes the issue by changing the wm8753 driver to use the generic
register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm9090 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm9090 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8962 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8962 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8955 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8955 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8904 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8904 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ian Lartey <ian@opensource.wolfsonmicro.com>
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8741 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8741 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ian Lartey <ian@opensource.wolfsonmicro.com>
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8523 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8523 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ian Lartey <ian@opensource.wolfsonmicro.com>
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the max98088 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the max98088 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Hsiang <Peter.Hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
Some codec drivers do not initialize the control_type field in their private
device struct, but still use it when calling snd_soc_codec_set_cache_io.
This patch fixes the issue by properly initializing it in the drivers probe
functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The assignment to the local variable 'channel' in
snd_ca0106_pcm_pointer_capture() is a little crazy. Order of assignment is
undefined. This fixes it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
They're very verbose and extremely repetitive so bulk up the kernel more
than is ideal. If required we can readd with WRITE_SEQUENCER_n type
definitions that cover the entire register bank in a few defines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Due to a typographical error in the erratum workaround it was never
functional so just remove it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix GPIO2-fixup for Sony laptops
ALSA: hda - Try to find an empty control index when it's occupied
ALSA: hda - Fix conflict of d-mic capture volume controls
ALSA: hda - Don't apply ALC269-specific initialization to ALC275
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
ALSA: pcm: remember to always call va_end() on stuff that we va_start()
ALSA: HDA: Add auto-mute for Thinkpad SL410/SL510
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The fix-up entries by the commit 2785591a97
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
weren't applied in the right position. They had to be before the quirk
entry matching to all Sony devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for 24 bit audio (with S32_LE msbits 24).
The reason to limit the msbits to 24, is that the FIFO
can be configured for 16 or 24 bit layout.
It is unknown how the codec would downsample from 32 to
24 bit, if the interface is configured to receive 32
bit data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change the structure of FIFO handling in order to
pave the way for adding 32/24 bit audio support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The manual FIFO configuration was the first version to enable
the use of the FIFO in the codec.
It had served it's purpose as debugging aid, but the automatic
FIFO configuration is much safer to use.
The removal of the manual controls, and configuration makes
it easier to add new features for the codec later, since
the manual mode neded different ways to calculate, and
protect against misconfiguration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make the phoenix HS and HF drivers use the new DAPM driver
widget in order to guarantee power ON/OFF order sequence.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds McBSP support for the OMAP4 CPU
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When a mixer control element was already created with the given name,
try to find another index for avoiding conflicts, instead of breaking
with an error. This makes the driver more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the d-mics are assigned to the same purpose of another analog mic
pins, the driver doesn't compute the index properly, resulting in an
error with "existing control". This patch fixes it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The WM8995 is a digital audio hub CODEC designed for smartphones.
The current driver supports most of the basic functionality of the
WM8995.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_jack_new()'s first parameter was changed from snd_soc_card to
snd_soc_codec after Multi-Component support patches. So, this patch
fixes parameter that we missed.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add jack detection interrupt trace to Wolfson CODEC drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This avoids blocking the IRQ thread and allows further bounces to extend
the debounce time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
FSI-AK4642 and FSI-DA7210 are depend on I2C, not I2C_SH_MOBILE
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make LZO cache compression optional as it pulls in the kernel wide LZO
implementation and rbtree compression is generally more efficient for
typical register maps, especially in terms of CPU performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This makes it easier to make cache types build time configurable as we
don't have a hard dependency on a given cache being built in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
