Teach atmel_lcdfb driver how to suspend/resume.
Note that the backlight control should probably do more of the same stuff:
turning off display power (more than just the backlight) and stopping the
clocks (and dma to drive the no-longer-seen display). No point in wasting
power to generate images that can't be observed, after all...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the dev arg of framebuffer_alloc() in arkfb, s3fb and vt8623fb.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After resume from STR, image is shifted by 8 pixels to the left. This patch
fixes it.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason to drive the savagefb I2C bus at such a low speed, so bump
it from 12.5 kbps to 50 kbps. The Intel (i810) and Matrox framebuffer drivers
already run their I2C bus at this speed, and so are the legacy i2c-savage4 and
i2c-prosavage drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in #if 0 inactivated function msttfb_load_cursor_image() the call eieio()
occurs after rather than in the loop due to missing curly brackets.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't treat valid modes returned by fb_find_mode() (best-fit modes, default
modes or the first valid mode) as errors.
Currently, when fb_find_mode() finds a valid mode belonging to one of the
above-mentioned classes, uvesafb will ignore it and will try to set a 640x480
video mode. The expected behaviour (introduced by this patch) would be to use
the valid mode returned by fb_find_mode() instead.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason to drive the radeon I2C buses at such a low speed, so bump
it from 12.5 kbps to 50 kbps. The Intel (i810) and Matrox framebuffer drivers
already run their I2C bus at this speed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTRACE() does exactly the same thing as the standard pr_debug() call, so just
use the latter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix CONFIG_FB_RADEON_DEBUG. DEBUG must be defined before including any kernel
header, otherwise dev_dbg() resolves to a no-op. Also, when debugging is
disabled, don't set DEBUG at all instead of setting it to 0, to comply with
what the kernel headers expect.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Additionally provide PCI device id in character format if possible. (The
printable characters were commonly used to identify the cards.)
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix incorrect length for strncat by replacing it with strlcat
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add removed option "mode" to keep compatibility with existing setups. The
option is back for pm2fb, tridentfb and vt8623fb drivers.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the option "mode_option". It also moves mtrr variable to devinitdata
section.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the option "mode_option". This is one step toward changing all fb
drivers to have common "mode_option" parameter.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the option "mode" into "mode_option".
This is one step toward changing all fb drivers to have common "mode_option"
parameter.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the option "mode_option".
This is one step toward changing all fb drivers to have common "mode_option"
parameter.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the option "mode_option" into "mode". It also adds __init attribute to
tridentfb_setup function.
This is one step toward changing all fb drivers to have common "mode_option"
parameter.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Alain Kalker <miki@dds.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the option "mode_option" into "mode".
This is one step toward changing all fb drivers to have common "mode_option"
parameter.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Alain Kalker <miki@dds.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Free buffer when the framebuffer can't be registered
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prior to suspend, we allocate and switch to a new VT; after suspend, we switch
back to the original VT. This can be slow, and is completely unnecessary if
the framebuffer we're using can restore video properly.
This adds a hook that allows drivers to select whether or not to do this vt
switch, and changes the gxfb driver to call this hook. It also adds a module
param to gxfb to allow controlling of the vt switch (defaulting to no switch).
(Note: I'm not convinced that console_sem is the best way to protect this, but
we should probably have some form of locking..)
[akpm@linux-foundation.org: build fix]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the ability to suspend/resume the gxfb driver, which includes:
- The addition of a Graphics Processor register table in gxfb.h, and
associated GP handling.
- Register and palette saving code; registers are stored in gxfb_par.
A few MSR values are saved as well.
- gx_powerup and gx_powerdown functions which restore/save registers and
enable/disable graphic engines.
- gxfb_suspend/gxfb_resume
Originally based on a patch by Jordan Crouse.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want to stop sharing stuff with gx1fb; it makes little sense. There were
fields in geodefb_par that weren't being used, there was little point to the
DC/VP ops callbacks, etc. This implements the following:
- Create gxfb_par (based on geodefb_par), place it in gxfb.h
- Drop display_gx.h and video_gx.h. The last few patches moved most
stuff into gxfb.h anyways, so there was very little left.
- Drop the geode_{dc,vid}_ops stuff. Un-static functions, add
declarations to gxfb.h.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This continues the gxfb header cleanups. MSRs are defined in geode.h; the
specific bits we care about are defined in gxfb.h.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This does the following in preparation for register saving:
- moves the register definitions from video_gx.h and display_gx.h into
gxfb.h.
- renames GX_* registers to match their section (ie, VP_).
- renames register bitfields to match the data sheet (ie,
DC_DCFG_TGEN -> DC_DISPLAY_CFG_TGEN).
- for DC registers, rather than defining to specific addresses, use
an enum to number them sequentially and just multiply by 4(bytes) to
access them (in read_dc/write_dc).
- for VP and FP registers, use an enum and multiple by 8 (bytes). They're
64bit registers.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This creates read_dc/write_dc, read_vp/write_vp, and read_fp/write_fp for
reading and updating those registers. It creates gxfb.h to house these.
We also drop a no-op readl() from gx_set_mode. Other than that, there should
be no functionality change.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a command line option (vram) rather than hardcoding the vram size. LxFB
already does this; it's useful for machines that can't query the BIOS for fb
size. This patch originated from David Woodhouse, was modified by Jordan
Crouse, and was then modified further by me.
This also adds some gxfb documentation in Documentation/fb.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the class/class_mask stuff; it's unnecessary as long as the vendor and
device IDs match.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the FP strap is enabled, don't turn on the CRT DACs - that will save
about 35 mA of power.
Updated/cleaned up by Andres Salomon.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While running in flatpanel mode it is important to change the FP sync bits (VG
register 0x408) rather then the CRT sync bits (VG register 0x008). This patch
keeps the CRT sync bits at default when a flatpanel exists.
Note that this also fixes inverted logic; we want CRT_VSYNC_POL to be set (ie,
vsync is normally high) when FB_SYNC_VERT_HIGH_ACT is unset.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleans up a few MSR-using drivers in the following manner:
- Ensures MSRs are all defined in asm/geode.h, rather than in misc
places
- Makes the naming consistent; cs553[56] ones begin with MSR_,
GX-specific ones start with MSR_GX_, and LX-specific ones start
with MSR_LX_. Also, make the names match the data sheet.
- Use MSR names rather than numbers in source code
- Document the fact that the LX's MSR_PADSEL has the wrong value
in the data sheet. That's, uh, good to note.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use __u32 for max_len to match the declaration of length in the struct
fb_bitfield.
Suppresses sparse shadowed variable warnings from the nested max()
macros:
drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
drivers/video/console/fbcon.h:130:8: warning: symbol '_y' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
[akpm@linux-foundation.org: fix constness]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix error values returned in some code branches in the pm2fb_probe() function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the framebuffers with non-native endianness. This is done via
FBINFO_FOREIGN_ENDIAN flag that will be used by the drivers. Depending on the
host endianness this flag will be overwritten by FBINFO_BE_MATH internal flag,
or cleared.
Tested to work on MPC8360E-RDK (BE) + Fujitsu MINT framebuffer (LE).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Clemens Koller <clemens.koller@anagramm.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, if a perfect match in terms of resolution is not found,
fb_find_mode() only looks for a best-fit mode among modes with a higher
resolution than the one requested. Thus, if the user requests a resolution
higher than the largest supported one, they are dropped to the default mode
(usually a low resolution one).
Change this behaviour so that all valid video modes are considered when
looking for a best-fit mode, while still preferring modes with a higher
resolution.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new function gpiochip_reserve() to reserve ranges of gpios that platform
code has pre-allocated. That is, this marks gpio numbers which will be
claimed by drivers that haven't yet been loaded, and thus are not available
for dynamic gpio number allocation.
[akpm@linux-foundation.org: remove unneeded __must_check]
[david-b@pacbell.net: don't export gpiochip_reserve (section fix)]
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If gpio_chip->base is negative during registration, gpiolib performs dynamic
base allocation. This is useful for devices that aren't always present, such
as GPIOs on hotplugged devices rather than mainboards. (This behavior was
previously specified but not implemented.)
To avoid using any numbers that may have been explicitly assigned but not yet
registered, this dynamic allocation assigns GPIO numbers from the biggest
number on down, instead of from the smallest on up.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a gpio_is_valid() predicate; use it in gpiolib.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ use inline function; follow the gpio_* naming convention;
work without gpiolib; all programming interfaces need docs ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduced owner field in struct gpio_chip to protect the
current (small) set of non-SOC GPIO drivers from being unloaded while any of
their GPIOs are in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ add mcp23s08 and pcf857x ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As long as one or more GPIOs on a gpio chip are used its driver should not be
unloaded. The existing mechanism (gpiochip_remove failure) doesn't address
that, since rmmod can no longer be made to fail by having the cleanup code
report errors. Module usecounts are the solution.
Assuming standard "initialize struct to zero" policies, this change won't
affect SOC platform drivers. However, drivers for external chips (on I2C and
SPI busses) should be updated if they can be built as modules.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ gpio_ensure_requested() needs to update module usecounts too ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since CONFIG_AVMB1_COMPAT is not a Kconfig variable, move it out of the
Kconfig namespace.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PNP driver interfaces depend on CONFIG_PNP, so test that rather than
__ISAPNP__.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a rather obvious cut-and-paste error, where earlier code for the
controller URB got somehow mixed in with code for the interrupt URB.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/isdn/hardware/eicon/message.c:745:47: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:761:45: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9122:16: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9147:16: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9173:14: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/divasmain.c:396:23: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/isdn/hardware/avm/b1isa.c:206:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1isa.c:208:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:664:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:666:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:668:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:791:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:793:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pci.c:385:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pci.c:387:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:886:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:888:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:890:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:973:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:975:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pcmcia.c:204:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pcmcia.c:206:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1isa.c:554:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1isa.c:556:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1pci.c:236:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1pci.c:238:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1091:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1093:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1095:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1170:21: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1294:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1296:33: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
