some BIOS only let AMD fam 10h handle bus0, and nvidia mcp55/ck804
to handle other buses. at that case MCFG will cover all over them.
but with acpi=off, we can not use MCFG. this patch will double check
the busnbits, and if it is less handling 256 bues, and acpi=off
will forcely reset the mmconf in msr, so we still use mmconf in above case.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we can use MMCONF when MMCONF is not set by BIOS
using TOP_MEM2 msr to get memory top, and try to scan fam10h mmio routing to
make sure the range is not conflicted with some prefetch MMIO that is above 4G.
(current only LinuxBIOS assign 64 bit mmio above 4G for some co-processor)
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
typical case: four sockets system, every node has 4g ram, and we are using:
memmap=10g$4g
to mask out memory on node1 and node2
when numa is enabled, early_node_mem is used to get node_data and node_bootmap.
if it can not get memory from the same node with find_e820_area(), it will
use alloc_bootmem to get buff from previous nodes.
so check it and print out some info about it.
need to move early_res_to_bootmem into every setup_node_bootmem.
and it takes range that node has. otherwise alloc_bootmem could return addr
that reserved early.
depends on "mm: make reserve_bootmem can crossed the nodes".
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Export linked list of struct setup_data via debugfs.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a field of 64-bit physical pointer to NULL terminated
single linked list of struct setup_data to real-mode kernel
header. This is used as a more extensible boot parameters passing
mechanism.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add free_early to early reservation mechanism - this way early bootup
failure paths can stop wasting memory.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes section mismatch warnings in unlock_ExtINT_logic().
WARNING: arch/x86/kernel/built-in.o(.text+0x14a92): Section mismatch in reference from the function unlock_ExtINT_logic()
to the function .init.text:find_isa_irq_pin()
The function unlock_ExtINT_logic() references
the function __init find_isa_irq_pin().
This is often because unlock_ExtINT_logic lacks a __init
annotation or the annotation of find_isa_irq_pin is wrong.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix following warning:
WARNING: arch/x86/kernel/built-in.o(.text+0x12cc9): Section mismatch in reference from the function unlock_ExtINT_logic()
unlock_ExtINT_logic() is only used by __init check_timer(). Annotate unlock_ExtINT_logic() witch __init.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix folowing warning:
WARNING: arch/x86/kernel/built-in.o(.text+0x10799): Section mismatch in reference from the function uniq_ioapic_id()
uniq_ioapic_id() is only used by __init mp_register_ioapic(). Annotate uniq_ioapic_id() with __init.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes section mismatch warnings of __cpuinit
setup_trampoline() on 32-bit host.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
get_bios_ebda() exists in asm/rio.h and asm/bios_ebda.h.
This patch removes the one in asm/rio.h.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the magic number in the third argment of div_sc().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the magic number in the second argument of clocksource_hz2mult()
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
memset and NULL check after alloc_bootmem() are unnecessary.
Because it returns zeroed memory and it never return NULL.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use bitmap library for pin_programmed rather than reinvent
bitmaps.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove duplicate code by using MP_intsrc_info() in mpparse.c
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use BUILD_BUG_ON() instead of compile-time error technique with
extern non-exsistent function.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that there are no more special cases in sys32_ptrace, we
can convert to using the generic compat_sys_ptrace entry point.
The sys32_ptrace function gets simpler and becomes compat_arch_ptrace.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This removes the special-case handling for PTRACE_GETSIGINFO
and PTRACE_SETSIGINFO from x86_64's sys32_ptrace. The generic
compat_ptrace_request code handles these.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This lifts the set_fs(USER_DS) call for signal handler setup out of the
three places copying the same code into the one place that calls them
all. There is no change in what it does.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This lifts the code diddling the TF and DF bits for signal handler setup
out of the several places copying the same code into the one place that
calls them all. There is no change in what it does.
I also separated the recently-added DF bit clearing from the TF diddling.
The compiler turns them back into one instruction anyway. The tossing
in of DF to the same line of code with no new comments was a bit more
arcane than seems wise.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is claimed that NexGen CPUs were never shipped:
http://lkml.org/lkml/2008/4/20/179
Also, the kernel support for these chips has been broken for
a long time, the code intended to support NexGen thereby being
essentially dead.
As an outcome of the discussion that can be found using the URL
above, this patch removes the NexGen support altogether.
The changes in this patch survived a defconfig build for i386, a
couple of successful randconfig builds, as well as a runtime test,
which consisted in booting a 32-bit x86 box up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In arch/x86/kernel/setup_64.c, the standard_io_resources array
is needlessly defined as global. This patch makes this variable
static.
This patch was successfully build-tested using the defconfig
for x86_64. Runtime test was performed by booting a 64-bit x86
box up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are no users for the function amd_init_cpu() defined in
arch/x86/kernel/cpu/amd.c. This patch removes this routine.
This patch was build-tested using defconfigs for i386 and x86_64,
and a few randconfig instances. Runtime tests were performed by
booting 32- and 64-bit x86 boxen up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At least on my Barcelona, I see MCE log entries after cold boot caused
by BIOS not properly clearing the respective registers. Therefore, this
patch extends the workaround to families 0x10 and 0x11 (the latter just
for completeness, I have nothing to verify this against).
At the same time, provide a way to make these entries visible via the
'mce=bootlog' command line option even on these machines.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
.. since it uses ILL_BADSTK (which is meaningless in the context of
SIGSEGV).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There apparently was an unnoticed conflict between an earlier patch to
this file and mine (d1e084746b), which
I noticed only now. I suppose a change like the one below (untested) is
needed; I didn't get any response on a confirmation request for this from
the submitter of the first patch.
The issue is the writing of the 'checkbit' member at the end of
setup_intel_arch_watchdog(), which my patch made go to intel_arch_wd_ops
rather than wd_ops.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Two prior changes resulted in the "ecx" clobber being lost.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-xen-next: (52 commits)
xen: add balloon driver
xen: allow compilation with non-flat memory
xen: fold xen_sysexit into xen_iret
xen: allow set_pte_at on init_mm to be lockless
xen: disable preemption during tlb flush
xen pvfb: Para-virtual framebuffer, keyboard and pointer driver
xen: Add compatibility aliases for frontend drivers
xen: Module autoprobing support for frontend drivers
xen blkfront: Delay wait for block devices until after the disk is added
xen/blkfront: use bdget_disk
xen: Make xen-blkfront write its protocol ABI to xenstore
xen: import arch generic part of xencomm
xen: make grant table arch portable
xen: replace callers of alloc_vm_area()/free_vm_area() with xen_ prefixed one
xen: make include/xen/page.h portable moving those definitions under asm dir
xen: add resend_irq_on_evtchn() definition into events.c
Xen: make events.c portable for ia64/xen support
xen: move events.c to drivers/xen for IA64/Xen support
xen: move features.c from arch/x86/xen/features.c to drivers/xen
xen: add missing definitions in include/xen/interface/vcpu.h which ia64/xen needs
...
Add some autogenerated files to various .gitignore files
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the codepath, remove alignment restrictions and do sanity
checking of the end result, to make sure we patched the right site.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
kernel_text_address returns true even for modules which is not wanted
in text_poke. Use core_kernel_text instead.
This is a regression introduced in e587cadd8f
which caused occasionaly crashes after suspend/resume.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Andi Kleen <andi@firstfloor.org>
CC: pageexec@freemail.hu
CC: H. Peter Anvin <hpa@zytor.com>
CC: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
xen_sysexit and xen_iret were doing essentially the same thing. Rather
than having a separate implementation for xen_sysexit, we can just strip
the stack back to an iret frame and jump into xen_iret. This removes
a lot of code and complexity - specifically, another critical region.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use jmp rather than call for the iret fixup, so its consistent with
the sysexit fixup, and it simplifies the stack (which is already
complex).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
64-bit Xen supports sysenter for 32-bit guests, so support its
use. (sysenter is faster than int $0x80 in 32-on-64.)
sysexit is still not supported, so we fake it up using iret.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make KERNEL_PGD_PTRS common, as previously it was only being defined
for 32-bit.
There are a couple of follow-on changes from this:
- KERNEL_PGD_PTRS was being defined in terms of USER_PGD_PTRS. The
definition of USER_PGD_PTRS doesn't really make much sense on x86-64,
since it can have two different user address-space configurations.
I renamed USER_PGD_PTRS to KERNEL_PGD_BOUNDARY, which is meaningful
for all of 32/32, 32/64 and 64/64 process configurations.
- USER_PTRS_PER_PGD was also defined and was being used for similar
purposes. Converting its users to KERNEL_PGD_BOUNDARY left it
completely unused, and so I removed it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Zach Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename (alloc|release)_(pt|pd) to pte/pmd to explicitly match the name
of the appropriate pagetable level structure.
[ x86.git merge work by Mark McLoughlin <markmc@redhat.com> ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
This isn't needed, we can just walk the devices in bus order with no
problems at all, as we really want to remove pci_get_device_reverse from
the kernel tree.
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
