This function is only referenced from within phy_device.c, so there is
no reason to export it. In fact, we can make it static.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_OF_MDIO is tristate and will be m if PHYLIB is m. Use
IS_ENABLED macro to prevent build error:
ERROR: "of_mdio_find_bus" [drivers/net/phy/mdio-mux.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add of_mdio_find_bus() which allows an mii_bus to be located given its
associated the device tree node.
This is needed by the follow-on patch to add a driver for MDIO bus
multiplexers.
The of_mdiobus_register() function is modified so that the device tree
node is recorded in the mii_bus. Then we can find it again by
iterating over all mdio_bus_class devices.
Because the OF device tree has now become an integral part of the
kernel, this can live in mdio_bus.c (which contains the needed
mdio_bus_class structure) instead of of_mdio.c.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: netdev@vger.kernel.org
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
This commit brings the author email address macros up to date for four
modules in the PTP Hardware Clock subsystem.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the x86-specific definition of irq_domain and replaces
it with the common implementation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the removal of get_driver()/put_driver(), this patch
(as1512) gets rid of various useless and unnecessary calls in several
drivers. In some cases it may be desirable to pin the driver by
calling try_module_get(), but that can be done later.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: "David S. Miller" <davem@davemloft.net>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Michael Buesch <m@bues.ch>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix new kernel-doc warning:
Warning(drivers/net/phy/mdio_bus.c:49): No description found for parameter 'size'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar problem as in 481a819914 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces
netif_rx() with netif_rx_ni() which has to be used from
process/softirq context.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function mdiobus_alloc_size() as an alternative to mdiobus_alloc().
Most callers of mdiobus_alloc() also allocate a private data structure, and
then manually point bus->priv to this object. mdiobus_alloc_size()
combines the two operations into one, which simplifies memory management.
The original mdiobus_alloc() now just calls mdiobus_alloc_size(0).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMSC generation 4 LAN chips integrate an IEEE 802.3 ethernet physical layer.
The ethernet driver for this family of devices needs to access the SMSC PHY
registers and bit-fields.
So, this patch moves these constants to a place where it can be used for both
the PHY and LAN drivers.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Frederic Lambert <frdrc66@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 88491d8103 ("drivers/net: Kconfig
& Makefile cleanup") changed the type of these options to bool, but
they select code that could (and still can) be built as modules.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert. New LPA translation functions have been added as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Translating between ethtool advertisement settings and MII
advertisements are common operations for ethernet drivers. This patch
adds a set of helper functions that implements the conversion. The
patch then modifies a couple of the drivers to use the new functions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy reset functionality to mdio-gpio driver. Now
mdio_gpio_platform_data has new member as function pointer which can be
filled at the bsp level for a callback from phy infrastructure. Also the
mdio-bitbang driver fills-in the reset function of mii_bus structure.
Without this patch the bsp level code has to takecare of the reseting
PHY's on the bus, which become bit hacky for every bsp and
phy-infrastructure is ignored aswell.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
If the PHY should disappear (for example, on an USB Ethernet MAC), then
the driver would leak any undelivered time stamp packets. This commit
fixes the issue by calling the appropriate functions to free any packets
left in the transmit and receive queues.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit enforces a new rule for handling the cloned packets
for transmit time stamping. These packets must not be freed using any other
function than skb_complete_tx_timestamp. This commit fixes the one and only
driver using this API.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Vitesse driver was using the RGMII_ID interface type to determine if
skew was necessary. However, we want to move away from using that
interface type, as it's really a property of the board's PHY connection.
However, some boards depend on it, so we want to support it, while
allowing new boards to use the more flexible "fixups" approach. To do
this, we extract the code which adds skew into its own function, and
call that function when RGMII_ID has been selected.
Another side-effect of this change is that if your PHY has skew set
already, it doesn't clear it. This way, the fixup code can modify the
register without config_init then clearing it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra delay of 2ns to adjust RX clock phase is actually needed
in RGMII mode. Tested on the HDK7108 (STx7108c2).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually you have to take the bus lock. Why not here too?
I saw this when working on something else. Not even compile tested.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Cc: "Uwe Kleine-Konig" <u.kleine-koenig@pengutronix.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to the mdio busses must be done with the mdio_lock to ensure
proper operation. Conveniently we have the helper function
mdiobus_read() to do that for us. Lets use it in get_phy_id() instead
of accessing the bus without the lock held.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.
This commit changes them to debug messages instead.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds one step support to the phyter. When enabled, the
hardware does not provide time stamps for transmitted sync messages but
instead inserts the stamp into the outgoing packet.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables six external event channels and one periodic output.
One GPIO is reserved for synchronizing multiple PHYs. The assignment
of GPIO functions can be changed via a module parameter.
The code supports multiple simultaneous events by inducing a PTP clock
event for every channel marked in the PHY's extended status word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP101A Single port 10/100 PHY
and supports the APS (i.e. power saving mode while link is down)
for both IP1001 and IP101A (where this mode is supported).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is does a general cleanup of the drivers/net/ Kconfig and
Makefile. This patch create a "core" option and places all
the networking core drivers into this option (default is yes
for this option). In addition, it alphabitizes the Kconfig
driver options.
As a side cleanup, found that the arcnet, token ring, and PHY
Kconfig options were a tri-state option and should have been
a bool option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the DP83865 datasheet we need to clear
the interrupt status bit by writing a 1 to the
corresponding bit in INT_CLEAR (2:0 are reserved).
Proposed and tested by Thorsten.
Signed-off-by: Thorsten Schubert <tshu@msc-ge.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dp83640 buffers receive time stamps from special PHY status frames,
matching them to received PTP packets in a work queue. Because the timeout
for orphaned time stamps is so long and the buffer is so small, the driver
can drop time stamps under moderate PTP traffic.
This commit fixes the issue by decreasing the timeout to (at least) one
timer tick and increasing the buffer size.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
if (...)
return ret;
return ret;
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
The dp83640 PHY provides time stamp and other information via special
PHY status frames. Previously, the driver decoded the frames and then
let the network stack drop them. This works fine when the PTP messages
come over UDP.
However, when receiving PTP messages via L2 packets, this creates a
problem. The status frames use the official PTP destination MAC address,
and so they are delivered to user space along with the "real" frames,
causing confusion for applications.
This commit fixes the issue by simply dropping the PHY status frames
in the driver.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
If two eternal time stamp events occur at nearly the same time, the
phyter will add an extra word into the status frame. This commit fixes
the parsing code to recognize and skip over the extra word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
This PHY is available integrated into BCM63xx series SOCs only.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/phy/Kconfig | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
If the dp83640 driver is not built as a module, the
MODULE_DEVICE_TABLE reference to dp83640_tbl nops out.
Since the table isn't referenced elsewhere, it it causes
the following warning:
drivers/net/phy/dp83640.c:1095: warning: ‘dp83640_tbl’ defined but not used
This apparently is common with mdio_device_id table structures,
and is avoided by using __maybe_unused annotation.
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function phy_attach_direct attaches the phy and calls phy_init_hw.
phy_init_hw can fail, but the phy is still marked as attached. Successive
calls to phy_attach_direct will fail because the phy is busy.
[ 1.020000] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1)
[ 1.030000] eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
[ 2.050000] Sending DHCP requests .
[ 3.020000] PHY: 1:00 - Link is Up - 100/Full
[ 5.110000] ..... timed out!
[ 87.660000] IP-Config: Reopening network devices...
[ 88.190000] FEC: MDIO read timeout
[ 88.190000] eth0: could not attach to PHY
[ 88.190000] IP-Config: Failed to open eth0
[ 88.210000] FEC: MDIO read timeout
[ 88.210000] eth1: could not attach to PHY
[ 88.210000] IP-Config: Failed to open eth1
[ 88.220000] IP-Config: No network devices available.
[ 88.220000] Freeing init memory: 6968K
[...]
starting network interfaces...
ip: RTNETLINK answers: File exists
[ 94.000000] net eth0: PHY already attached
[ 94.010000] eth0: could not attach to PHY
ip: SIOCSIFFLAGS: Device or resource busy
This patch adds phy_detach to clean up if phy_init_hw fails.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib would silently ignore the phy_id argument to these ioctls and
perform the read/write with the active phydev address, whereas most
non-phylib drivers seem to allow access to all mdio addresses
(E.G. pcnet_cs).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup
routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL
PHY work with 50MHz RMII reference clock.
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded depends on PHYLIB. The config selection is already in
an if PHYLIB / endif block.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing. The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver. We run into problems however if the PHY connections
are specified by the device tree. There is no way for the Ethernet
driver to know what flags it should pass.
If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.
The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants. A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:
phy5: ethernet-phy@5 {
reg = <5>;
compatible = "marvell,88e1149r";
marvell,reg-init =
/* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
<3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
/* mix %:0, led[0123]:drive low off hiZ */
<3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
/* default blink periods. */
<3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
/* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
<3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
};
phy6: ethernet-phy@6 {
reg = <6>;
compatible = "marvell,88e1118";
marvell,reg-init =
/* Fix rx and tx clock transition timing */
<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
/* Adjust LED drive. */
<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
/* irq, blink-activity, blink-link */
<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
};
The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number. These are
the first and second word. The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value. The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.
If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY. The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The marvell 88ec048's official part number is 88e1318s. This patch renames
definitions in the driver to reflect this.
In addition, a minor bug fix has been added to write back the MSCR1 register
value properly.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used directly by any drivers:
phy_attach_direct
phy_device_create
phy_prepare_link
genphy_config_advert
genphy_setup_forced
phy_config_interrupt
phy_clear_interrypt
phy_sanitize_settings
phy_enable_interrupts
phy_disable_interrupts
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c477d0447d added support for RGMII
rx/tx delays except that it ends up clearing rx/tx delays bit for modes
differents that RGMII*ID. Due to this, ethernet is not working anymore
on my guruplug server +. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel doesn't have a symbol called BCM63XX. There is a symbol
BCM63XX_ENET (introduced in 9b1fc55a05, 6 weeks after 09bb9aa0ed that
introduced BCM63XX_PHY), but the driver compiles without that, too.
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module. So when building-in support for the phys, the
mdio_device_id tables are unused. Marking them with __maybe_unused
fixes the following warnings:
drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.
This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net/ipv4: Eliminate kstrdup memory leak
net/caif/cfrfml.c: use asm/unaligned.h
ax25: missplaced sock_put(sk)
qlge: reset the chip before freeing the buffers
l2tp: test for ethernet header in l2tp_eth_dev_recv()
tcp: select(writefds) don't hang up when a peer close connection
tcp: fix three tcp sysctls tuning
tcp: Combat per-cpu skew in orphan tests.
pxa168_eth: silence gcc warnings
pxa168_eth: update call to phy_mii_ioctl()
pxa168_eth: fix error handling in prope
pxa168_eth: remove unneeded null check
phylib: Fix race between returning phydev and calling adjust_link
caif-driver: add HAS_DMA dependency
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
qlcnic: fix poll implementation
netxen: fix poll implementation
bridge: netfilter: fix a memory leak
It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:
Unable to handle kernel paging request for data at address 0x0000024c
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
P1021 RDB
Modules linked in:
NIP: c0345dac LR: c0345dac CTR: c0345d84
TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
[...]
NIP [c0345dac] adjust_link+0x28/0x19c
LR [c0345dac] adjust_link+0x28/0x19c
Call Trace:
[c0d25f00] [000045e1] 0x45e1 (unreliable)
[c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
[...]
Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:
static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}
So that adjust_link could retrieve it back:
static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}
If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).
Now, phy_connect starts the PHY state machine before returning phydev to
the driver:
phy_start_machine(phydev, NULL);
if (phydev->irq > 0)
phy_start_interrupts(phydev);
return phydev;
The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.
To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix phy.c kernel-doc notation:
Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.
This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for RGMII RX/TX delay configuration on marvell 88e1121
and derivatives. With this patch, PHY_INTERFACE_MODE_RGMII_*ID modes are now
supported on these devices.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
