Adds R61, T61p, X61s, X61, Z61m, Z61p models to whitelist.
Fixes this:
cullen@lenny:~$ sudo modprobe hdaps
FATAL: Error inserting hdaps (/lib/modules/2.6.22-10-generic/kernel/drivers/hwmon/hdaps.ko): No such device
[25192.888000] hdaps: supported laptop not found!
[25192.888000] hdaps: driver init failed (ret=-19)!
Originally based on an Ubuntu patch that got it wrong, the dmidecode
output of the corresponding laptops shows LENOVO as the manufacturer.
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/133636
tested on X61s:
[ 184.893588] hdaps: inverting axis readings.
[ 184.893588] hdaps: LENOVO ThinkPad X61s detected.
[ 184.893588] input: hdaps as /class/input/input12
[ 184.924326] hdaps: driver successfully loaded.
Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org>
Cc: Chuck Short <zulcss@ubuntu.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LM75 sensor reading bugfix: never save error status as valid
sensor output. This could be improved, but at least this
prevents certain rude failure modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
It has been reported that the abituguru3 driver fails to load after a BIOS
update. This patch fixes this by loosening the detection routine so that it
will work after the BIOS update too. To compensate for the now very loose
detection an additional check is added on the DMI Base Board vendor string to
make sure we only load on Abit motherboards, this is the same as the check in
the abituguru (1 / 2) driver.
Signed-of-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch identifies the Abit AW8D board as such, and adds support for its
aux5 fan connector
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
data->max_duty_at_overheat is not updated in adt7473_update_device,
so it might be used before it is initialized (if the user reads from
sysfs file max_duty_at_crit before writing to it.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Function RANGE_TO_REG() is broken. For a requested range of 2000 (2
degrees C), it will return an index value of 15, i.e. 80.0 degrees C,
instead of the expected index value of 0. All other values are handled
properly, just 2000 isn't.
The bug was introduced back in November 2004 by this patch:
http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commit;h=1c28d80f1992240373099d863e4996cdd5d646d0
While this can be fixed easily with the current code, I'd rather
rewrite the whole function in a way which is more obviously correct.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Justin Thiessen <jthiessen@penguincomputing.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Adds DMI system identifier for ThinkPad T61.
Originally written by Klaus S. Madsen.
Taken from http://launchpadlibrarian.net/10864950/hdaps-t61.patch
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.
[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor rework to support the Intel 5400 chipset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (adt7473) minor cleanup / refactoring
hwmon: (asb100) Remove some dead code
hwmon: (lm75) Fix an incorrect comment
hwmon: (w83793) VID and VRM handling cleanups
hwmon: (w83l785ts) Don't ask the user to report failures
hwmon: (smsc47b397) add a new chip id (0x8c)
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
High-byte first is not opposite to the usual practice - that's what
almost all hardware monitoring drivers do. It is opposite to the SMBus
standard though.
Also delete a duplicate comment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Rework the device initialization function so as to read the
"Multi-Function Pin Control" register (0x58) once instead of twice.
I2C transactions aren't cheap so this speeds up the driver loading.
* Only create the "vrm" attribute if at least one VID value is
available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <jgong@winbond.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
There's nothing we can do about read errors on the W83L785TS-S, so
don't ask the user to report them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource makes the request
(and thus the detection) fail.
This fixes lm-sensors ticket #2306:
http://www.lm-sensors.org/ticket/2306
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
ibmpex's temperature sensors report incorrect units. Apply a conversion
factor so that tempertures report correctly. Until now, no systems seemed to
report temperatures this way, but evidently QS2x blades do.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhanced the list of supported machines.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The QS2x blades ships with v2.54 of the firmware, which use the same
multiplier for all power meters.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added a new ID (0x8c) for the smsc47b397 hardware monitor driver.
This ID is used by HP in, at least, their dc7700 line.
Signed-off-by: Craig Kelley <namonai@gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for family 0x17, which has Penryn Core. It should also
cover the 8 cores Xeons.
Can someone test please? I think it should work.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following patch will finally solve the detection of Intel Mobile CPUs which
share same CPUID with Desktop/Server CPUs. We need this information to test
some bit so we know if TjMax is 100C or 85C. Intel claims this works for mobiles
only, respect that and set for desktops the TjMax to 100C. Intel provided some
table on their wiki based on my chat with them at:
http://softwarecommunity.intel.com/isn/Community/en-US/forums/30247249/ShowThread.aspx#30247249
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
On my mid-2007 MacBook2, reading Ts0P sensor always failed with this message:
applesmc: wait status failed: 5 != 50.
So I assume that there's no such Ts0p sensor in this model (please confirm,
anyone). If there's the case, then we need a new set of sensors defined for
MacBook2.
Signed-off-by: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix following warning:
WARNING: vmlinux.o(.text+0xebfd04): Section mismatch in reference from the function coretemp_cpu_callback() to the function .cpuinit.text:coretemp_device_add()
coretemp_cpu_callback() are only used inside a
HOTPLUG_CPU block so annotate it __cpuinit.
The notifier referencing the function are annotated
__refdata to silence warning from the exit function.
The unregister function do not use the embedded pointer
but clears the variable so the annotation is OK.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following patch will add reporting of maximum temperature, at which all fans
should spin full speed. It may be non-physical temperature on Desktop/Server CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The missing NULL at the end of two sysfs file groups causes a kernel
crash when calling sysfs_create_group().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm and fault files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use standard dynamic sysfs callbacks instead of macro-generated
functions. This makes the code more readable, and the binary smaller
(by about 34%).
As a side note, another benefit of this type of cleanup is that they
shrink the build time. For example, this cleanup saves about 29% of
the lm80 driver build time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Drop trailing whitespace
* Fold a long line
* Rename new_client to client
* Drop redundant initializations to 0
* Drop bogus comment
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm and beep files. The
code was copied from the w83781d driver. I've tested the alarm files
on a W83627THF. I couldn't test the beep files as the system in
question doesn't have a speaker.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
If VBAT monitoring is disabled, enable it. Bug reported on the
lm-sensors trac system:
http://lm-sensors.org/ticket/2282
This is the exact same patch that was applied to the w83627ehf driver
6 months ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
While the W83627EHF/EHG has only 6 VID pins, the W83627DHG has 8 VID
pins, to support VRD 11.0. Add support for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The new libsensors needs these individual alarm files.
I did not create alarm files for in5 and in6 as these alarms are documented
as not working.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use standard dynamic sysfs callbacks instead of macro-generated
wrappers. This makes the code more readable, and the binary smaller
(by about 12%).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
