uapsd_queues and uapsd_max_sp_len are relevant only for managed
interfaces, and can be configured differently for each vif.
Move them from the local struct to sdata->u.mgd, and update
the debugfs functions accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some debugfs write functions call kstrto* functions, which
assume the string is null-terminated. Make it valid by changing
ieee80211_if_write() to use static buffer instead of allocating
one, and set the last char to NULL.
(The write functions try to parse some integer/mac address,
so 64 bytes buffer should be enough)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current max throughput rate is known to be good as otherwise it
wouldn't be the max throughput rate. Since rate sampling can introduce
some overhead (by adding RTS for example or due to not aggregating the
frame) don't sample the max throughput rate.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When regulatory information changes our HT behavior (e.g,
when we get a country code from the AP we have just associated
with), we should use this information to change the power with
which we transmit, and what channels we transmit. Sometimes
the channel parameters we derive from regulatory information
contradicts the parameters we used in association. For example,
we could have associated specifying HT40, but the regulatory
rules we apply may forbid HT40 operation.
In the situation above, we should reconfigure ourselves to
transmit in HT20 only, however it makes no sense for us to
disable receive in HT40, since if we associated with these
parameters, the AP has every reason to expect we can and
will receive packets this way. The code in mac80211 does
not have the capability of sending the appropriate action
frames to signal a change in HT behaviour so the AP has
no clue we can no longer receive frames encoded this way.
In some broken AP implementations, this can leave us
effectively deaf if the AP never retries in lower HT rates.
This change breaks up the channel_type parameter in the
ieee80211_enable_ht function into a separate receive and
transmit part. It honors the channel flags set by regulatory
in order to configure the rate control algorithm, but uses
the capability flags to configure the channel on the radio,
since these were used in association to set the AP's transmit
rate.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Sam Leffler <sleffler@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R Rodriguez <mcgrof@frijolero.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value is not really very useful by itself,
yet some drivers (including iwlwifi until I can
figure out what it should do) use it. At least
rename it to "last_tsf" to indicate the meaning
and add a note that it may be really old.
I suspect the value may become useful combined
with the rx_status->mactime, but we don't (yet)
store that value and pass it to the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is intended to be the timestamp sent by the
peer in the beacon/probe response, not any form
of host timestamp. Clarify the documentation and
variable names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not linearizing every SKB will help actually pass
non-linear SKBs all the way up when on an encrypted
connection. For now, linearize TKIP completely as
it is lower performance and I don't quite grok all
the details.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is better done inside the WEP decrypt
function where it doesn't have to check all
the conditions any more since they've been
tested already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The authentication and association handshake
already happens in the context of the new BSS,
and the basic rates are needed at least for
the ACK response frame to the authentication
or association response frames. Therefore the
basic rates should already be configured into
the driver when those frames are sent.
Change the logic to set up the basic rates in
the connection preparation that happens for
authentication and association (if needed).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As associating is possible without first authenticating
(for FT over DS) association also has to be able to
switch to the right channel, insert the station entry
etc. Factor out this common code into a new function
called ieee80211_prep_connection().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSSID has been set a lot earlier already and
didn't change again in ieee80211_set_associated().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting assoc_data->wmm_used solely
based on the BSS also take into account our own
capabilities and later check those.
Also rename "wmm_used" and "uapsd_used" to just
"wmm" and "uapsd".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always set/use IEEE80211_STA_DISABLE_11N instead
of duplicating the queue, WMM and HT checks in
all places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looks like some changes in this area moved
the code but not the comment that belongs
to the code, move it to the right place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable multi stream rates (MCS > 7) when a STA is in static SMPS mode
since it has only one active rx chain. Hence, it doesn't even make
sense to sample multi stream rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we've discussed, we want to avoid channel changes
while associated. While the part when we actually
associate needs a bit more work, the bit that happens
on disassociating can be changed quite easily. Move
the channel type change later in the disassociate
process to set the channel only after the driver was
told that it's now disassociated.
As the driver could expect powersave to be enabled
only when associated, this thus results in splitting
the config call, but overall what happens makes more
sense this way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the station state callback was added, this
was no longer needed in theory. With the iwlwifi
changes to remove use of it landing, we can kill
the entire tx-sync framework again, RIP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While setting up or tearing down a BA session mac80211 is buffering
pending frames for the according TID. However, there's currently no
limit on how many frames are buffered possibly leading to an out-of-
memory situation. This can happen on systems with little memory when
the CPU is fully loaded since the BA session work is executed in
process context while frames can still come via softirq.
Apply a limitation to the TIDs pending queue to avoid consuming
too much memory in this situation.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Receive background scan period as part of connect
command and pass the same to the driver.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "{nl,cfg,mac}80211: Implement RSSI threshold for mesh peering"
has a potential null pointer dereferencing problem. Thanks to Dan Carpenter
for pointing out. This patch will fix the issue.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 is lenient with respect to reception of corrupted beacons.
Even if the frame is corrupted as a whole, the available IE elements
are still passed back and accepted, sometimes replacing legitimate
data. It is unknown to what extent this "feature" is made use of,
but it is clear that in some cases, this is detrimental. One such
case is reported in http://crosbug.com/26832 where an AP corrupts
its beacons but not its probe responses.
One approach would be to completely reject frames with invaid data
(for example, if the last tag extends beyond the end of the enclosing
PDU). The enclosed approach is much more conservative: we simply
prevent later IEs from overwriting the state from previous ones.
This approach hopes that there might be some salient data in the
IE stream before the corruption, and seeks to at least prevent that
data from being overwritten. This approach will fix the case above.
Further, we flag element structures that contain data we think might
be corrupted, so that as we fill the mac80211 BSS structure, we try
not to replace data from an un-corrupted probe response with that
of a corrupted beacon, for example.
Short of any statistics gathering in the various forms of AP breakage,
it's not possible to ascertain the side effects of more stringent
discarding of data.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Sam Leffler <sleffler@chromium.org>
Cc: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The socket local pointer needs to be set to NULL when the adapter is
removed or the MAC goes down.
If the socket release code is called after such an event, the socket
reference count still needs to be decreased in order for the socket to
eventually be freed.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calling nfc_dep_link_up, we implicitely are in initiator mode.
Which means we also can provide the general bytes as a function argument,
as all drivers will eventually request them.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We just don't do anything with it when parsing the general bytes.
We handle it from the CONNECT reception code.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The parent socket (the bound one) could be freed before its children, so
we should unlink the children without trying to reach it through the parent.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the receiver MIU, we have to fragment the frame to be
transmitted.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the maximum values for the LLCP Maximum Information Unit and Receive
Window Size.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to acknowledge an I frame, we have to either queue pending local
I frames or queue a receiver ready frame.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This one will be called from the I frame command sending.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For user space to know if a device is up or down.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airtime link metric estimation was broken in HT mesh, use
cfg80211_calculate_bitrate to get the right rate value.
Also factor out tx rate copying from sta_set_sinfo().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associating and particularly when disassociating
there's no need to notify the driver about changes
with multiple calls to bss_info_changed, we should
combine the QoS enabling/disabling into the same call
as otherwise the driver could get confused about QoS
suddenly getting disabled while connected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to hardcode a subset of the
radiotap header for cooked monitor receive,
we can just reuse the normal monitor mode
radiotap code. This simplifies the code and
extends the information available on cooked
monitor interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RANN, PREP and PERR propagation should happen only if the
dot11MeshForwarding is true. Besides, data frame should not be
forwarded if dot11MeshForwarding is false. This redundant checking
is necessary to avoid the broadcasted ARP breaking the non-forwarding
rule.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For A-MPDU rx it makes sense to only process the signal strength once per
aggregate instead of once per subframe. Additonally, some hardware (e.g.
Atheros) only provides valid signal strength information for the last
subframe.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several MAC address comparison functions assume 16 bit alignment for pointers
passed to them. Since the addition of the control_port field, alignment
for the IBSS bssid was off by one, causing a severe performance hit on
architectures without efficient unaligned access (e.g. MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
