Some laptop has an internal analog microphone that is 'fixed'.
This patch prevents creating a 'Mic In as Output' switch for
ports that can't be outputs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Support added for detecting HP jack presence via GPIO on several laptop docks.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add SPDIF playback switch to the slave element list so that it
can be toggled via the master control as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch checks to see the Line In/Mic port have the ability
to do output before creating the the control switches.
The 92hd71bxx series of codecs has this issue with the port 0xe,
which only allows input.
Signed-off-by: Matthew Ranostay <mranostay@embededalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed issue that the incorrect GPIO line was being pulled high
for some STAC9205 based laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allows for dynamically creating mono out mixer controls and well
as mono mux controls.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for the mono mux on several 92HD7xxx codecs.
Creates a dynamic mixer for the mux selection.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes. So, added a stupid workaround here temporarily...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There are two similar GPIO-enablement codes in patch_sigmatel.c.
Let's clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a new STAC 9205 quirk for Vostro 1500.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for advanced power management support for output ports on
92HD7xxx family of codecs. Inactive output ports are powered down when
the pin sense doesn't detect a connection, and powered back up when a
connection is sensed.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Moved 2 systems PCI_QUIRK values to STAC_DELL_BIOS. Also the second
front HP jack is incorrect defined in the BIOS VT's for some laptops,
this patch corrects this.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a mono output mute mixer for the 92hd71bxx family of codecs, this
also removes the need for the mono out node to explicitly unmuted in the
core init.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dynamically create digital gain mixers for dmics that have out-amp
support. Also some 92HD73xx's codecs don't have DMIC gains, so this also
prevents creating dead mixers.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some laptops incorrectly assume the front input jack as a line in
instead of a microphone in. Which in turn disables the voltage
reference, in which non-amplified input is not possible. This patch
enables VREF80 for the input jack.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The digital mux on STAC codecs doesn't always exist although the
driver builds dmux enum mixer elements unconditionally.
Now the driver creates 'digital input source' mixer elements only
when dmux is available.
Also, the patch adds the missing dmux definition for STAC925x.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cleaned up STAC927x and added several subsystem id's for more laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added more codecs to the 92HD71 family, as well as support for several
that don't have an analog mixer.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Changed hardware gain mixers for the digital mic's from HDA_OUTPUT to
HDA_INPUT.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for new STAC92HD73 family of codecs. Additionally added
features for multiple analog loopbacks, and multiple dmux mixers.
Regression testing for the analog loopback changes for STAC9205 and
STAC9274D completed with any issues, as well for the dmux changes.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly so that
invalid values won't be stored or written to registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When a mic jack is set up as the multiple I/O, it may issue the automute
function wrongly. This patch fixes the wrong automute detection.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dell laptops have multiple HP jacks that can be used for multi-channel
outputs. The current auto pincfg handles the speaker as the primary
output and thus cannot handle the multi-channel configuration for such
cases. This patch adds a workaround to fix this issue by swapping the
HP and speaker during multi-channel setup routines.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Updated dell-m82 model pin config table. The old config doesn't work
with Dell 1210 and co.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added more laptops subsystem id's that have STAC9228 DMIC support.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added analog loopback support and missing ADC capture mixer for the
STAC92HD71 codec family.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added initial support for the STAC92HD71BXX family of codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for the dmics and enabled EAPD for several laptops with
STAC9228 cards.
Signed-off-by: Matthew Ranostay <mranostay@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Changed the dmux for STAC9228 from ADC1MUX to ADC0MUX to avoid confusion.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a dmux to the STAC9228 cards with DMIC support. And added a
STAC_DIGITAL_INPUT_SOURCE macro for repeating mixer code.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing STAC9228 DMIC support.
Also added a new vendor id tag for IDT.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The addition of volume knob as Master volume resulted in conflict with
the existing one by stac92xx_auto_create_hp_ctls().
This patch fixes the conflict, and still keeps the Master control for
codecs without volume knob as much as possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by Jan-Marek Glogowski.
The dmic array is passed to snd_hda_parse_pin_def_config() and
should be zero-terminated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by zhejiang <zhe.jiang@intel.com>
'I found that STAC_VOLKNOB hardwired the KNOB nid to 0x24.
It is okay for stac9205 and stac927x.
But the VolumeKnob nid of stac9220-9221 is 0x16.'
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
My bad, I forgot to update the num_items field when added a new item
to vaio_mux items table, so the last item 'PCM' disappeared.
Now it has the right number 3.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the output of Gateway laptops with STAC9200 codec chip.
They require the EAPD control for some pins. These pins shouldn't be
powered down.
To enable EAPD control, a new model 'gateway' was added to STAC9200.
The known PCI SSIDs are included in the quirk list.
The fix was originally suggested by Brian Hinz, in ALSA bug#2948.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
More laptop BIOS changes the subsystem id for STAC9205 cards if the
microphone is toggled on/off in the settings.
The patch removes the old STAC_9205_M43xx and use STAC_9205_DELL_M43.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some laptop BIOS change the subsystem id for STAC9205 cards if the
microphone isn't toggled on/off in the settings.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The last patch to change/add Dell models have wrong pin config orders.
This patch fixes the pin positions.
Taken from ALSA bug#3319,
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3319
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
1) Create seperate mixer controls for each ADC
2) Make number of substreams of capture PCM device be equal to
number of ADCs
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
VolumeKnob is present on most sigmatel codecs, it allows to decrease
volume of all DACs at once, it is a kind of post-procesing volume.
Note that all output amps of sigmatel only decrease volume, and all
input amps only increase volume.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The analog loopback routes the sound just before it enters ADC0
to output of DAC0.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Center/LFE channels are located on same jack, so it can be usefull
to swap them.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The STAC codes adds line_out_pins[] for shared mic/line-inputs accordingly.
But, the current code may give a hole with NID=0 in some setting, which
results in an error at probe. This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The resume procedure for STAC codecs overrides the cached values and
results in the wrong (reset) PIN state. The patch gets rid of the
overriding part and simplifies the resume.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
