It didn't set up the CPU possible map early enough, so the
option didn't actually work.
Noticed by Heiko Carstens
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains a printk reorder to remove the current problem of
displaying "PCI-DMA: Disabling IOMMU." and then "PCI-DMA: using GART
IOMMU" 20 lines later in dmesg.
It also constains a printk reorder in swiotlb to state swiotlb
enablement prior to describing the location of the bounce buffers, and a
printk reorder to state gart enablement prior to describing the
aperature.
Also constains a whitespace cleanup in arch/x86_64/kernel/setup.c
Tested (along with patch 2/2) on dual opteron with gart enabled,
iommu=soft, and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They cause quite bad performance regressions on Netburst
This is temporary until we can get new optimized functions
for these CPUs.
This undoes changes that were done in 2.6.15 and in 2.6.16-rc1,
essentially bringing the code back to 2.6.14 level. Only change
is I renamed the X86_FEATURE_K8_C flag to X86_FEATURE_REP_GOOD
and fixed the check for the flag and also fixed some comments.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... reducing the amount of changes Xen has to do.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
X86_FEATURE_K8_C was a synthetic Linux CPUID flag that was used for some
code optimizations in Opteron C stepping or later. But support for pre C
stepping optimizations has been removed, so this isn't needed anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch enables early intialization of cpu_to_node.
apicid_to_node is built by reading the SRAT table, from acpi_numa_init with
ACPI_NUMA and k8_scan_nodes with K8_NUMA.
x86_cpu_to_apicid is built by parsing the ACPI MADT table, from acpi_boot_init.
We combine these two tables and setup cpu_to_node.
Early intialization helps the static per_cpu_areas in getting pages from
correct node.
Change since last release:
Do not initialize early init_cpu_to_node for faking node cases.
Patch tested on TYAN dual core 4P board with K8 only, ACPI_NUMA.
Tested on EM64T NUMA. Also tested with numa=off, numa=fake, and running
a kernel compiled with NUMA on a regular EM64 2 way SMP.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The real vsyscall .text addresses are not mapped when the alternative()
replacement runs early, so use some black magic to access them using
the direct mapping.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AK: I hacked Muli's original patch a lot and there were a lot
of changes - all bugs are probably to blame on me now.
There were also some changes in the fall back behaviour
for swiotlb - in particular it doesn't try to use GFP_DMA
now anymore. Also all DMA mapping operations use the
same core dma_alloc_coherent code with proper fallbacks now.
And various other changes and cleanups.
Known problems: iommu=force swiotlb=force together breaks
needs more testing.
This patch cleans up x86_64's DMA mapping dispatching code. Right now
we have three possible IOMMU types: AGP GART, swiotlb and nommu, and
in the future we will also have Xen's x86_64 swiotlb and other HW
IOMMUs for x86_64. In order to support all of them cleanly, this
patch:
- introduces a struct dma_mapping_ops with function pointers for each
of the DMA mapping operations of gart (AMD HW IOMMU), swiotlb
(software IOMMU) and nommu (no IOMMU).
- gets rid of:
if (swiotlb)
return swiotlb_xxx();
- PCI_DMA_BUS_IS_PHYS is now checked against the dma_ops being set
This makes swiotlb faster by avoiding double copying in some cases.
Signed-Off-By: Muli Ben-Yehuda <mulix@mulix.org>
Signed-Off-By: Jon D. Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people need it now on 64bit so reuse the i386 code for
x86-64. This will be also useful for future bug workarounds.
It is a bit simplified there because there is no need
to do it very early on x86-64. This means it doesn't need
early ioremap et.al. We run it as a core initcall right now.
I hope it's not needed for early setup.
I added a general CONFIG_DMI symbol in case IA64 or someone
else wants to reuse the code later too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print bits for RDTSCP, SVM, CR8-LEGACY.
Also now print power flags on i386 like x86-64 always did.
This will add a new line in the 386 cpuinfo, but that shouldn't
be an issue - did that in the past too and I haven't heard
of any breakage.
I shrunk some of the fields in the i386 cpuinfo_x86 to chars
to make up for the new int "x86_power" field. Overall it's
smaller than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define it for i386 too.
This is a synthetic flag that signifies that the CPU's TSC runs
at a constant P state invariant frequency.
Fix up the logic on x86-64/i386 to set it on all known CPUs.
Use the AMD defined bit to set it on future AMD CPUs.
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on the documentation recently posted by Richard Brunner.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- elfcorehdr= specifies the location of elf core header stored by the
crashed kernel. This command line option will be passed by the kexec-tools
to capture kernel.
Changes in this version :
- Added more comments in kernel-parameters.txt and in code.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
- This patch introduces the memmap option for x86_64 similar to i386.
- memmap=exactmap enables setting of an exact E820 memory map, as specified
by the user.
Changes in this version:
- Used e820_end_of_ram() to find the max_pfn as suggested by Andi kleen.
- removed PFN_UP & PFN_DOWN macros
- Printing the user defined map also.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Hariprasad Nellitheertha <nharipra@gmail.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
What is the value shown in "cpu MHz" of /proc/cpuinfo when CPUs are capable of
changing frequency?
Today the answer is: It depends.
On i386:
SMP kernel - It is always the boot frequency
UP kernel - Scales with the frequency change and shows that was last set.
On x86_64:
There is one single variable cpu_khz that gets written by all the CPUs. So,
the frequency set by last CPU will be seen on /proc/cpuinfo of all the
CPUs in the system. What you see also depends on whether you have constant_tsc
capable CPU or not.
On ia64:
It is always boot time frequency of a particular CPU that gets displayed.
The patch below changes this to:
Show the last known frequency of the particular CPU, when cpufreq is present. If
cpu doesnot support changing of frequency through cpufreq, then boot frequency
will be shown. The patch affects i386, x86_64 and ia64 architectures.
Signed-off-by: Venkatesh Pallipadi<venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Fix up booting with sparse mem enabled. Otherwise it would just
cause an early PANIC at boot.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.
CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdfhttp://download.intel.com/design/Pentium4/specupdt/30235221.pdf
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.
This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped. Druing boot, all the processors will use this as their
level4 pgt. On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses. On AP's we will zap the low mappings as
soon as we jump to C code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.
This also adds a generic numa_node_id to all the topology includes
Suggested by Eric Dumazet
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.
AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If VMX feature is available in the CPU, this patch will make it visible in
the /proc/cpuinfo with the cpuid detection.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.14-rc2 does not assign cpus to proper nodeids on our em64t numa boxen.
Our boxes use acpi srat for parsing the numa information.
srat_detect_node() used phys_proc_id[] to get to the cpu's local apic id,
but phys_proc_id[] represents the cpu<->initial_apic_id mapping. The
following patch fixes this problem. Now apicid_to_node[] is properly
indexed with the local apic id.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I checked with AMD and they requested to only disable it for family 15.
Also disable it for i386 too. And some style fixes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They seem to have been due to AMD errata 63/122; the fix is to disable
TLB flush filtering in SMP configurations.
Confirmed to fix the problem by Andrew Walrond <andrew@walrond.org>
[ Let's see if we'll have a better fix eventually, this is the Q&D
"let's get this fixed and out there" version ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular on systems where the local APIC space and node space
is very different from the Linux CPU number space.
Previously the older NUMA setup code directly parsing the K8
northbridge registers had some issues on 8 socket or dual core
systems. This patch fixes them.
This is mainly done by fixing some confusion between Linux
CPU numbers and local APIC ids. We now pass the local APIC IDs
to later code, which avoids mismatches.
Also add some heuristics to detect cases where the Hypertransport
nodeids and the local APIC IDs don't match, but are shifted
by a constant offset.
This is still all quite hackish, hopefully BIOS writers fill
in correct SRATs instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do that later when the CPU boots. SRAT just stores the APIC<->Node
mapping node. This fixes problems on systems where the order
of SRAT entries does not match the MADT.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_vendor() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark variables which are usually accessed for reads with __readmostly.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the sparse mem changes and the kexec changes
were merged into setup.c they came in, in the wrong order.
This patch changes the order so we don't run sparse_init
which uses the bootmem allocator until we all of the
reserve_bootmem calls has been made.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Does not change any semantics because numa_add_cpu checks for CPU 0 anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it. This is an intent for it. The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug). For BP, restore_processor_state is responsible for
restoring MTRR.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the x86_64 implementation of the crashkernel option. It reserves
a window of memory very early in the bootup process, so we never use
it for anything but the kernel to switch to when the running
kernel panics.
In addition to reserving this memory a resource structure is registered
so looking at /proc/iomem it is clear what happened to that memory.
ISSUES:
Is it possible to implement this in a architecture generic way?
What should be done with architectures that always use an iommu and
thus don't report their RAM memory resources in /proc/iomem?
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds __cpuinit and __cpuinitdata sections that need to exist past
boot to support cpu hotplug.
Caveat: This is done *only* for EM64T CPU Hotplug support, on request from
Andi Kleen. Much of the generic hotplug code in kernel, and none of the other
archs that support CPU hotplug today, i386, ia64, ppc64, s390 and parisc dont
mark sections with __cpuinit, but only mark them as __devinit, and
__devinitdata.
If someone is motivated to change generic code, we need to make sure all
existing hotplug code does not break, on other arch's that dont use __cpuinit,
and __cpudevinit.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds in the necessary support for sparsemem such that x86-64
kernels may use sparsemem as an alternative to discontigmem for NUMA
kernels. Note that this does no preclude one from continuing to build NUMA
kernels using discontigmem, but merely allows the option to build NUMA
kernels with sparsemem.
Interestingly, the use of sparsemem in lieu of discontigmem in NUMA kernels
results in reduced text size for otherwise equivalent kernels as shown in
the example builds below:
text data bss dec hex filename
2371036 765884 1237108 4374028 42be0c vmlinux.discontig
2366549 776484 1302772 4445805 43d66d vmlinux.sparse
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to use the alternative sparsemem implmentation for NUMA kernels,
we need to reorganize the config options. This patch effectively abstracts
out the CONFIG_DISCONTIGMEM options to CONFIG_NUMA in most cases. Thus,
the discontigmem implementation may be employed as always, but the
sparsemem implementation may be used alternatively.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch pulls out all remaining direct references to contig_page_data
from arch/x86-64, thus saving an ifdef in one case.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove duplicated ifdef
- Make core_id match what Intel uses
- Initialize phys_proc_id correctly for non DC case
- Handle non power of two core numbers.
Fixes for both i386 and x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is not very useful to the user and more an kernel internal implementation
detail. So hide it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
