The Marvell CaFe is now marked as having bad card detection to fix
a problem during system resume.
Now on the OLPC XO-1 we are facing the issue that the card is marked
as logically unremovable (via MMC_UNSAFE_RESUME), which means that
mmc_card_is_removable considers the card non-removable. The existing
code logic decides not to poll for card presence in this case, and
card detection is also disabled because of the quirk being set.
This means that no SD cards are detected when inserted after boot.
Refine the logic to enable card presence polling in the case when
a card is logically unremovable, only avoiding the poll in the case
when the card is physically non-removable (denoted with
MMC_CAP_NONREMOVABLE).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new flag of SDHCI_USING_RETUNING_TIMER to represent if the host
is using a retuning timer for the card inserted.
This flag is set when the host does tuning the first time for the card
and the host's retuning mode is 1. This flag is used afterwards whenever
needs to decide if the host is currently using a retuning timer.
This flag is cleared when the card is removed in sdhci_reinit.
The set/clear of the flag and the start/stop of the retuning timer is
associated with the card's init/remove time, so there is no need to
touch it when the host is to be removed as at that time the card should
have already been removed.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When debugging one bad issue, got lots of pr_warning messages
"queuing unknown CIS tuple" which caused a printk storm and
flooded the console.
This patch changes the pr_warning to use pr_warn_ratelimited.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In mmc_read_switch, just do a one time mode 0 switch command to get the
support bits information, no need to do multiple times as the support
bits do not change with different arguments.
And no need to check current limit support bits, as these bits are
fixed according to the signal voltage. If the signal voltage is 1.8V,
the support bits would be 0xf and if the signal voltage is 3.3V, the
support bits would be 0x01. We will check host's ability to set the
current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some of the host settings are affected by different cards inserted, e.g.
when an UHS-I card is inserted, the SDHCI_NEEDS_RETUING flag might be
set when the tuning timer expired and host's max_blk_count will be
reduced to make sure the data transfer for a command does not exceed 4MiB
to meet the retuning mode 1's requirement.
When the card is removed, we should restore the original setting of the
host since we can't be sure the next card being inserted will still be
an UHS-I card that needs tuning. The original setting include its
max_blk_count and no set of the flag of SDHCI_NEEDS_RETUNING.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For SD hosts using retuning mode 1, when retuning timer expired, it will
need to do retuning in sdhci_request before processing the actual
request. But the retuning command is fixed: cmd19 for SD card and cmd21
for eMMC card, so we can't use the original request's command to do the
tuning.
And since the tuning command depends on the card type attached to the
host, we will need to know the card type to use the correct tuning
command.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Cc: stable <stable@vger.kernel.org> [3.3+]
Signed-off-by: Chris Ball <cjb@laptop.org>
At http://dev.laptop.org/ticket/11980 we have determined that the
Marvell CaFe SDHCI controller reports bad card presence during
resume. It reports that no card is present even when it is.
This is a regression -- resume worked back around 2.6.37.
Around 400ms after resuming, a "card inserted" interrupt is
generated, at which point it starts reporting presence.
Work around this hardware oddity by setting the
SDHCI_QUIRK_BROKEN_CARD_DETECTION flag.
Thanks to Chris Ball for helping with diagnosis.
Signed-off-by: Daniel Drake <dsd@laptop.org>
[stable@: please apply to 3.0+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For most error conditions sdhci_add_host() will print a diagnostic
message indicating why it failed but there are a few cases where this
does not happen. Add error messages in these cases to aid diagnosis.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The s3c2410_gpio* calls are obsolete and have been scheduled for
removal since several kernel releases. Remove them and use common
gpiolib API.
This patch is a prerequisite for removal of the S3C24XX SoC specific
arch/arm/plat-samsung/include/gpio-fns.h header.
Tested on Micro2440-SDK.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently only the capability_0 register can be set if
SDHCI_QUIRK_MISSING_CAPS is defined. This is a problem when
the capability_1 register also needs changing. Use the quirk
SDHCI_QUIRK_MISSING_CAPS to allow both registers to be set.
Redefining caps[1] is useful when the board design does not
support 1.8v vccq so UHS modes are not available. The code that
calls sdhci_add_host can then detect this condition and adjust
the caps so the UHS mode will not be attempted on UHS cards.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If bootloader or platform initialization code does not enable the
power supply to mmc slot, we need to do it in mmc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The effect of the existing code is that we continue blindly when we
should warn about an invalid allocation unit.
Reported-by: dcb314@hotmail.com
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44061
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If we are using a regulator the SD Host Controller and the
regulator should agree about the voltages supported. Use
the common subset that is supported.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_current_caps can return 0 if not available from the sd controller.
If no regulator is present or the regulator specifies a current
less then 200ma, we no longer still set the 200mA caps bit anyway.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron_lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sd host controller spec indicates the the MAX_CURRENT value may
be returned as 0. In this case other methods need to be used to
return the current. If 0 is returned and there is a regulator,
ask the regulator for how much current is available.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Extend the sh_mmcif driver to support GPIO card detection, provided by the
slot function module. The original .get_cd() platform callback is also
preserved for now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently mmc host drivers have to decide whether to enable card
detection before calling mmc_add_host() -- in which case a card
insertion event can arrive before the host has been completely
initialised -- or after mmc_add_host(), in which case the initial
card detection can be problematic.
This patch adds an explicit indication of when card detection should
not be carried out. With it in place enabling card detection before
calling mmc_add_host() should be safe. Similarly, disabling it again
after calling mmc_remove_host() will avoid any races.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add primitive OF support to the sh-mmcif driver, which also makes it
necessary to be able to run without platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add primitive support for OF to the SDHI TMIO glue, which also makes it
necessary to be able to run without platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tmio-mmc driver is already using the generic GPIO CD handler in IRQ
mode. This patch adds support for CD polling mode and also checks for
availability of a WP GPIO.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Let SDHI platforms specify mmc_host::caps2 flags in their platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to
the mmc layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Write-Protect pin is often implemented, using a GPIO, which makes
it simple to provide a generic handler for it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This prepares for the addition of further slot functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A simple extension of mmc slot functions add support for CD GPIO polling
for cases where the GPIO cannot produce interrupts, or where this is not
desired for some reason.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
struct mmc_host::hotplug is becoming a generic hook for slot functions.
Rename it accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add regulator support to the sh_mmcif driver, but also preserve the current
power-callback.
Also note, that the card power is not switched off during clock gating
periods, hence there's no need to power it on every time the card is
re-activated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
From the original version of sh_mmcif the .set_pwr() callback has only been
used to turn the card's power on, and the .down_pwr() callback has been
used to turn it off. .set_pwr() can be used for both these tasks, which is
also how it is implemented by the only user of this API: the SH7724 ecovec
board.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
With aggressive clock gating the clock can be disabled during interface
inactivity. During this time its frequency can be changed by another its
user. Therefore when the interface is activated again and the clock is
re-enabled, its frequency has to be re-read.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Regardless of whether the MMC bus clock is the same as the PM clock on
this specific interface, it has to be managed separately. Its proper
management should also include enabling and disabling of the clock,
whenever the interface is becoming active or going idle respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
A check for NULL platform data can be conveniently made in the very
beginning of probing. Replace numbered error-handling labels in .probe()
with meaningful names to make any future reorganisation simpler.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the SDHI glue for the TMIO MMC driver installs dummy .get_cd() and
.set_pwr() callbacks even if the platform didn't supply them. This is not
necessary, since the TMIO MMC driver itself checks for NULL callbacks. This
is also dubious if the platform provides a regulator for SD-card power
switching. It is better to only install those callbacks, if they are really
provided by the platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the TMIO MMC driver derives the OCR mask from the platform data
and uses a platform callback to turn card power on and off. This patch adds
regulator support to the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Instead of delivering one static clock frequency value, read from the
hardware during probing, enable the tmio-mmc driver to re-read the
frequency dynamically.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Every time the clock is enabled after possibly being disabled, we have
to re-read its frequency and update our configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
We don't have to force-enable MMC interrupts in our .probe() method,
mmc_add_host() will trigger card detection, that will enable all the
necessary interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
host->dma_ops is not valid if host->usa dma is 0 so protect
host->dma_ops reference in dw_mci_resume
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a function to get regulators, supplying card's Vdd and Vccq on a
specific host. If a Vdd supplying regulator is found, the function checks,
whether a valid OCR mask can be obtained from it. The Vccq regulator is
optional. A failure to get it is not fatal.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tmio_mmc_set_ios() function configures the MMC power, clock and bus
width. When the mmc core requests the driver to power off the card, we
inform runtime PM, that the controller can be suspended. This can lead
to the MSTP clock being turned off.
Writing to any 16-bit hardware registers with the MSTP clock off leads
to timeouts and errors being printed to the kernel log. This can occur
both when stopping the MMC clock and when configuring the bus width.
To fix this, stop the MMC clock before calling put_runtime_pm(), and
skip bus width configuration when power is off.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC_SLEEP_AWAKE and SD_IO_SEND_OP_COND commands share the same
opcode. SD_IO_SEND_OP_COND isn't supported by the SH MMCIF, but
MMC_SLEEP_AWAKE is. Discriminate between the two commands using the
command flags, and reject SD_IO_SEND_OP_COND only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the current dwmmc driver there is support for selecting IDMAC from
the menu config option. If the support for IDMAC is enabled in the menu
config and the hardware configuration register's DMA_INTERFACE field is
0, the driver will still try to do the DMA initialization.
The dw_mci_idmac_init function currently implemented returns only success
indicating that the DMA initialization is always successful. This patch
adds a check for existence of the DMA IP to allow the DMA initialization.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The regulator API functions we're wrapping are exported as GPL, so our
wrappers for the same functions should be too.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For completing any block request, MMC block driver is calling:
spin_lock_irq(queue)
__blk_end_request()
spin_unlock_irq(queue)
But if we analyze the sources of latency in kernel using ftrace,
__blk_end_request() function at times may take up to 6.5ms with
spinlock held and irq disabled.
__blk_end_request() calls couple of functions and ftrace output
shows that blk_update_bidi_request() function is almost taking 6ms.
There are 2 function to end the current request: ___blk_end_request()
and blk_end_request(). Both these functions do same thing except
that blk_end_request() function doesn't take up the spinlock
while calling the blk_update_bidi_request().
This patch replaces all __blk_end_request() calls with
blk_end_request() and __blk_end_request_all() calls with
blk_end_request_all().
Testing done: 20 process concurrent read/write on sd card
and eMMC. Ran this test for almost a day on multicore system
and no errors observed.
This change is not meant for improving MMC throughput; it's basically
about becoming fair to other threads/interrupts in the system. By
holding spin lock and interrupts disabled for longer duration, we
won't allow other threads/interrupts to run at all. Actually slight
performance degradation at file system level can be expected as we
are not holding the spin lock during blk_update_bidi_request() which
means our mmcqd thread may get preempted for other high priority
thread or any interrupt in the system.
These are performance numbers (100MB file write) with eMMC running
in DDR mode:
Without this patch:
Name of the Test Value Unit
LMDD Read Test 53.79 MBPS
LMDD Write Test 18.86 MBPS
IOZONE Read Test 51.65 MBPS
IOZONE Write Test 24.36 MBPS
With this patch:
Name of the Test Value Unit
LMDD Read Test 52.94 MBPS
LMDD Write Test 16.70 MBPS
IOZONE Read Test 52.08 MBPS
IOZONE Write Test 23.29 MBPS
Read numbers are fine. Write numbers are bit down (especially LMDD
write), may be because write requests normally have large transfer
size and which means there are chances that while mmcq is executing
blk_update_bidi_request(), it may get interrupted by interrupts or
other high priority thread.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_execute_hpi should send the HPI command only once, and only
if the card is in PRG state.
According to eMMC spec, the command's completion time is
not dependent on OUT_OF_INTERRUPT_TIME. Only the transition
out of PRG STATE is guarded by OUT_OF_INTERRUPT_TIME - which
is defined to begin at the end of sending the command itself.
Specify the default timeout for the actual sending of HPI
command, and then use OUT_OF_INTERRUPT_TIME to wait for
the transition out of PRG state.
Reported-by: Alex Lemberg <Alex.Lemberg@sandisk.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc.h defines macros for most frequently used MMC opcodes. Use them instead
of hard-coded numbers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix a boot regression on Mackerel boards with sh_mobile_sdhi
in existing kernels causing:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq XXX
caused by 1c6c6952 (genirq: Reject bogus threaded irq requests).
This is backported from Guennadi's patch:
"mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions"
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 3d93576e(skip card initialization if
power class selection fails).
Problem has been reported when this is used with eMMC4.41
card with Tegra Platform. Till the issue is root caused,
bus width selection failure should not be treated as fatal.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-Off-by: Venkatraman S <svenkatr@ti.com>
CC: Ulf Hansson <ulf.hansson@stericsson.com>
CC: Subhash Jadavani <subhashj@codeaurora.org>
CC: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
