New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.
Tested only on AT26F004.
Signed-off-by: Hans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The ops.len member is not initialized, because it is unused for this
operation. The length check needs to use ops.ooblen instead
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
o A dependency on the processor architecture does not make sense;
delete it.
o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
make those dependencies.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add flash and rootfs mappings for the PMC-Sierra MSP71xx devices.
This patch references some platform support files previously submitted to
the linux-mips@linux-mips.org list.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Classify the page data and oob buffer
and it prevents the memory fragementation (writesize + oobsize)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When transferring/filling of the oob is finished in OOB_AUTO, we exit the loop
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
add Nokia Copyright and a credit
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In oob functions, it is used main buffer instead of oob one. So fix it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If an erase operation fails, the address at which the
failure occurred is returned by the driver. The MTD
partition must adjust this address (by subtracting the
partition offset) before returning to the caller.
This was not happening, which caused JFFS2 to mark
the wrong block bad!
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Replace the apparently misspelled preprocessor variable
"MTD_NAND_DISKONCHIP_BBTWRITE" with the correct form
"CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The type of a resource could be 32 or 64bit depending upon platform or
option so cast it explicitly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The files cfi_cmdset_0002.c and cfi_cmdset_0020.c do not initialize their
wait queues like is done in cfi_cmdset_0001.c. This causes an oops when
the wait queue is accessed. I have copied the code from cfi_cmdset_0001.c
that is pertinent to initialization of the wait queue.
Signed-off-by: Vijay Sampath <vsampath@gmail.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add checking for closed ROM window on Intel ESB2 Southbridge.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the MTD rework the oobavail parameter of mtd_info structure has become
private. This is not quite correct in terms of integrity and logic. If we have
means to write to OOB area, then we'd like to know upfront how many bytes out
of OOB are spare per page to be able to adapt to specific cases.
The patch inlined adds the public oobavail parameter.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Noticed while building a s3c2410 kernel :
drivers/mtd/nand/s3c2410.c: In function 's3c2440_nand_calculate_ecc':
drivers/mtd/nand/s3c2410.c:476: warning: format '%06x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
This patch fixes it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Over the years there was a slow trickle of complaints against the readahead
code. Most of them concerned performance, Peter Zijlstra stumbled over it
when working unrelated changes and I believe there was an actual bug report.
Oh, Andrew Morton also complained about duplicating code from mm/readahead.c.
It is just not worth it. On flash media like usb sticks, readahead will
make things go slow - very slow. On spinning disks, readahead may be a
win, but this is definitely not the place to add it.
Signed-off-by: Jörn Engel <joern@lazybastard.org>
drivers/mtd/devices/block2mtd.c:311:9: warning: symbol 'dev' shadows an earlier one
drivers/mtd/devices/block2mtd.c:294:23: originally declared here
Signed-off-by: Jörn Engel <joern@lazybastard.org>
Remove two casts - they were not only pointless, but outright harmful.
Spotted by Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jörn Engel <joern@lazybastard.org>
S3C2412 use differents registers than s3c2440 for hw ecc handling.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.fr>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/cafe.c: In function 'cafe_nand_cmdfunc':
drivers/mtd/nand/cafe.c:269: warning: 'irqs' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/maps/ichxrom.c: In function 'ichxrom_init_one':
drivers/mtd/maps/ichxrom.c:231: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
drivers/mtd/maps/ichxrom.c:231: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/maps/amd76xrom.c: In function 'amd76xrom_init_one':
drivers/mtd/maps/amd76xrom.c:209: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/maps/esb2rom.c: In function 'esb2rom_init_one':
drivers/mtd/maps/esb2rom.c:293: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/maps/ck804xrom.c: In function 'ck804xrom_init_one':
drivers/mtd/maps/ck804xrom.c:211: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
drivers/mtd/maps/ck804xrom.c:211: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/maps/netsc520.c: In function 'init_netsc520':
drivers/mtd/maps/netsc520.c:97: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/maps/sc520cdp.c:241: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
drivers/mtd/maps/netsc520.c: In function 'init_netsc520':
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/onenand/onenand_base.c: In function 'onenand_bbt_read_oob':
drivers/mtd/onenand/onenand_base.c:1033: warning: format '%i' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all calls to invalidate_inode_pages() into open-coded calls to
invalidate_mapping_pages().
Leave the invalidate_inode_pages() wrapper in place for now, marked as
deprecated.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a nand flash driver for the eXcite series of intelligent
cameras manufactured by Basler Vision Technologies AG.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Correct the location of the recalculation of the FIS directory size,
and also add the same recalculation for the byte-swapped case.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for correcting errors detected by the
hardware ECC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove unused and broken mtd->ecctype and mtd->eccsize fields
from struct mtd_info. Do not remove them from userspace API
data structures (don't want to breake userspace) but mark them
as obsolete by a comment. Any userspace program which uses them
should be half-broken anyway, so this is more about saving
data structure size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove ugly and weird MTD_PROGREGION_CTRLMODE_VALID() and
MTD_PROGREGION_CTRLMODE_INVALID() macros. There is only one
user of them and they are used locally just for printing.
Anyway, this patch is a preparation for removing mtd->ecctype
and mtd->eccsize, but these macros use them. Fix this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The cfi_staa_write_buffers() uses mtd->eccsize but means mtd->writesize.
BTW, mtd-eccsize is broken and is not initialized, which means the code
fixed by this patch is broken/unused anyway.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
OneNAND has internal bufferRAMs. The driver keeps track of
what is in the bufferRAM to save having to load from the
NAND core. After an erase operation, the driver must
mark bufferRAM invalid if it refers to the erased block.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This fixes a regression with the RedBoot parsing code introduced by
commit 0b47d65408
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
err_pos_lut[4096] of an array with 4096 elements is a bug.
Spotted by the Coverity checker.
While I was at it, I also converted it to ARRAY_SIZE().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add checks to ensure that out-of-band reads and writes are
not attempted with an invalid offset or length. Specifically,
the offset must be less than the size of oob for a page
and the length must not go beyond the size of the device.
Additionally the checks must adjust for auto-placement
(MTD_OOB_AUTO) of oob data.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In commit c172471b78 Nico switched to using
common code for polling for command completion. Unfortunately he also used
a common default timeout for both write and erase commands, despite the
fact that erases can take a _whole_ lot longer. Use a more sensible
default for erase timeout.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
CONFIG_MTD_CK804XROM=y, CONFIG_PCI=n results in the following compile
error:
CC drivers/mtd/maps/ck804xrom.o
ck804xrom.c: In function 'ck804xrom_init_one':
ck804xrom.c:114: error: implicit declaration of function 'pci_dev_get'
ck804xrom.c:114: warning: assignment makes pointer from integer without a cast
make[4]: *** [drivers/mtd/maps/ck804xrom.o] Error 1
Considering what hardware this driver is driving, a dependency on PCI
also seems logical.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
OneNAND double-density package (DDP) has two chips, each with
their own bufferRAM. The driver will skip loading data from
the NAND core if the data can be found in a bufferRAM, however
in that case, the correct chip's bufferRAM must be selected
before reading from bufferRAM.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Provide the bad block scan with its own read function so that important error
messages that are not from the the bad block scan, can always be printed.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
When a write is done, the length written is returned. When a
single subpage is written the length returned should be the
subpage size, however the page size was being returned.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
OneNAND can write oob to successive pages, but NAND
does not do that. For compatibility, disallow OneNAND
from writing past the end of the page.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
It use blockpage instead of a pair (block, page). It can also cover a small chunk access. 0x00, 0x20, 0x40 and so on.
And in JFFS2 behavior, sometimes it reads two pages alternatively.
e.g., It first reads A page, B page and A page.
So we check another bufferram to find requested page.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
- Iterations of the patch to add oob auto-placement support to OneNAND left a line of code that was meant to have been deleted.
- read mtd->oobsize in onenand_transfer_auto_oob to optimized memcpy
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Enable the use of oob operation mode MTD_OOB_AUTO with OneNAND.
Note that MTD_OOB_RAW is still not supported.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Going over the bugs and warnings I found this one left over. The other
changes have already been correctly done for this driver but the actual
switch to pci_get_device that they assume has not.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When write-verify is enabled (CONFIG_MTD_ONENAND_VERIFY_WRITE),
the data written is read back and compared. The comparison
was being made between dataRAM buffers, but this does not
verify that the data made it to the dataRAM correctly in
the first place. This patch amends write-verify to
compare back to the original buffer. It also now verifies
sub-page writes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The precise timings are board-specific (or NAND chip specific) and don't
belong here. If they're set already, then use what we find there.
Otherwise, revert to the most conservative default values (and whinge).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
OneNAND records bad block information in the out-of-band area of either the first or second page of a block. Due to a logic error, only the first page was being checked.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
OneNAND does 2 memory allocations for bad block information.
Only one of them was being freed.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
If OneNAND is operating within specification, all operations should easily be
completed within the 20 millisecond timeout.
This patch faithlessly adds a check for the timeout and returns an error in
that case.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The read-while-load method of reading from OneNAND needs to allow
for the change of bufferRAM address at the boundary between the
two chips in a double density (DDP) device.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
we don't need to return ecc error when 1-bit ecc.
We only return error code when 2-bit ecc error
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch teaches OneNAND to release processor in
read/write/erase cycles and let other processes proceed.
Also, remove buggi touch watchdog call which only hides
the problem instead of solving it.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Return a fault code if the Dataflash driver runs into a "no device present"
error when the MISO line has a pulldown (it currently expects a pullup), so
that rmmod won't oops.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build issues that show up with the m25p80 SPI flash driver when
building with MTD debug enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the ITE8172 based boards was deleted a while ago so this is
dead code.
The Kconfig dependency on MIPS was wrong anyway, MIPS is a processor
architecture and nothing else; guesses on systems architecture are likely
to be wrong ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
Only clever people can get away with that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ESB2ROM uses PCI interface functions.
With CONFIG_PCI=n:
drivers/mtd/maps/esb2rom.c: In function 'esb2rom_init_one':
drivers/mtd/maps/esb2rom.c:167: warning: implicit declaration of function 'pci_dev_get'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
inlined below is the patch that adds physmap driver for of_device.
It's an MTD part of the two-part support for flash/ROM devices based
on Open Firmware descriptions. The arch part (currently only PowerPC
which is no surprise) was introduced to powerpc folks earlier and
recently the older version of the powerpc part has been included into
the powerpc.git tree
(see http://www.kernel.org/git/?p=linux/kernel/git/paulus/powerpc.git;a=commitdiff;h=28f9ec349ae47c91768b7bc5607db4442c818e11).
drivers/mtd/maps/Kconfig | 9 +
drivers/mtd/maps/Makefile | 1
drivers/mtd/maps/physmap_of.c | 255 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 265 insertions(+)
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Sergey Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
RedBoot supports storing the FIS directory and the RedBoot
configuration area in the same block of flash memory. This is
not the most common RedBoot configuration, but it is used on
commercially available boards supported by the kernel.
A recent patch to mtd/redboot.c (http://lkml.org/lkml/2006/3/20/410)
which corrected the skipping of deleted table entries has exposed the
latent problem of the kernel redboot parser running off the end of the
FIS directory and interpreting the RedBoot configuration information
as table entries.
This patch terminates the table parsing when the first truly empty
entry is found (table entry deletion only clears the first byte of the
name, so two cleared bytes in a row indicates the end of the table),
thereby supporting the combined redboot FIS directory and RedBoot
configuration information flash layout scenario.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for 16-bit NAND bus-width for the AT91 NAND driver.
The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.
Orignal Patch from Patrice Vilchez
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Number of address bytes for 64-128 MiB NANDs is 4, not 5.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Select MTD_NAND_ECC_SMC (ECC byte order according to the Smart Media
Specification) if MTD_NAND_NDFC is used.
Using the wrong byte order causes fatal, unnoticed data damage.
For further information see:
http://lists.infradead.org/pipermail/linux-mtd/2006-November/016920.html
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Can't analyze FIS directory in CYGSEM_REDBOOT_FLASH_COMBINED_FIS_AND_CONFIG
really.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch fixes the
"jffs2_flash_writev(): Non-contiguous write to 00825300 with mtd_dataflash" bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
The newly-added cafe_ecc.c had a lot of it because of the way the lookup
table was auto-generated; clean up the other files too while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
While we're fixing up the newly-added symbol, change the neighbouring ones
too, for consistency and also to reflect the author's interpretation of
the GPL -- which is that _no_ non-GPL modules are permitted. The author
always intended his code to be released under the GPL, and believes that
any new interpretation of 'EXPORT_SYMBOL' as being any different from
'EXPORT_SYMBOL_GPL' is entirely invalid; the GPL requires that _all_
exports have the semantics of the new 'EXPORT_SYMBOL_GPL', which means the
extra four characters are entirely redundant.
But since those four extra characters trigger the check for illegal
modules in a way that just EXPORT_SYMBOL does not, it's useful to change
anyway. This action in no way indicates an admission that there is any
legal distinction between the two states, and in particular does not
indicate that the author believes that non-GPL modules may use symbols
exported with EXPORT_SYMBOL alone.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
get_mtd_device() returns NULL in case of any failure. Teach it to return an
error code instead. Fix all users as well.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds get_device() and put_device() methods to the MTD description
structure (struct mtd_info). These methods are called by MTD whenever the MTD
device is get or put. They are needed when the underlying driver is something
smarter then just flash chip driver, for example UBI.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds one more function to the MTD interface to make it possible to
open MTD devices by their names, not only numbers. This is very handy in many
situations. Also, MTD device number depend on load order and may vary, while
names are fixed.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Add a MTD_BLKDEVS Kconfig option to cleanup the makefile a bit
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch has fixed name of map probe for cstm_mips_ixx.c
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up the config option in the #ifdef statements in nand_ecc.c
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix printk format warning:
drivers/mtd/maps/physmap.c:93: warning: long long unsigned int format, long unsigned int arg (arg 2)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently, mtd_blkdevs enforces a block size of 512, even if the drivers
can seemingly request a different size. This patch fixes mtd_blkdevs so
block sizes other than 512 work correctly.
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for accessing BIOS flash chips connected to the NVIDIA ck804 southbridge.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The writel() call accidentally clears all bits in the NDFC_CCR
register (endianess problem). Now __raw_writel() is used instead.
Tested on Bamboo with NAND on chip select 0 and chip select 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the needlessly global mtdpart_setup() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch converts drivers/mtd/nand/rtc_from4.c to use the new
lib/bitrev.c
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We can use the two methods to wait.
1. polling: read interrupt status register
2. interrupt: use kernel ineterrupt mechanism
To use interrupt method, you first connect onenand interrupt pin to your
platform and configure interrupt properly
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
We were resetting cafe->ctl2 to zero after an erase (and also during a
write, but it was correctly reset after that). This meant that ECC reads
after an erase were failing. Doh.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Also use cafe_readl() and cafe_writel() abstraction to make code
slightly cleaner -- especially if we want to use it in PIO mode.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add description of 'raw' in comments for
drivers/mtd/nand/nand_base.c::nand_write_page_syndrome() so 'make xmldocs'
will not spew a warning at us.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being a value which isn't in the table is a case we explicitly check for
in the caller. Don't BUG_ON() because it does actually happen in
practice.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When a flash-based BBT is not used, nand_default_mark_blockbad() is supposed
to mark the block bad in the oob. However, it sets the wrong length variable
so that no bad block marker is in fact written. This patch attempts to
rectify that.
(As note, it seems to be that logically, it shouldn't be necessary to set
both length variables, as one appears to be for the main buffer, and
one for the oob buffer, but this is how it is done in several places,
including the code for the mtd character device MEMWRITEOOB and MEMREADOOB
ioctls. I'm not sure if this is a temporary solution during some rework of
the mtd infrastructure, or whether there is a deeper thought here.)
Signed-off-by: Ricard Wanderlöf <ricardw@axis.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ditch the separate oobrbuf and oobwbuf fields from the chip buffers,
and use only a single buffer immediately after the data. This accommodates
NAND controllers such as the OLPC CAFÉ chip, which can't do scatter/gather
DMA so needs the OOB buffer to be contiguous with the data, for both read
and write.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
