The current code for reading the EEPROM via ethtool in the asix
driver has a few issues. It cannot handle odd length values
(accesses must be aligned at 16 bit boundaries) and interprets the
offset provided by ethtool as 16 bit word offset instead as byte offset.
The new code for asix_get_eeprom() introduced by this patch is
modeled after the code in
drivers/net/ethernet/atheros/atl1e/atl1e_ethtool.c
and provides read access to the entire EEPROM with arbitrary
offsets and lengths.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected. usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.
There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table. Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asix AX88172A is a USB 2.0 Ethernet interface that supports both an
internal PHY as well as an external PHY (connected via MII).
This patch adds a driver for the AX88172A and provides support for
both modes and the phylib.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the new driver for the AX88172A to share code with the
existing drivers for ASIX devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch further creates two additional copies of asix.c.
In another patch these copies will be used to factor out
common code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by implementation in smsc911x.c and smsc9420.c
Tested on ARM/pandaboard running android
Signed-off-by: Emeric Vigier <emeric.vigier@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a device with limited QMI support. It does not support
normal QMI_WDS commands for connection management. Instead,
sending a QMI_CTL SET_INSTANCE_ID command is required to
enable the network interface:
01 0f 00 00 00 00 00 00 20 00 04 00 01 01 00 00
A number of QMI_DMS and QMI_NAS commands are also supported
for optional device management.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed excess calls to skb_copy_expand() or memmove() in asix driver.
This driver needs to push 4 bytes in front of frame (packet_len)
and maybe add 4 bytes after the end (if padlen is 4)
So it should set needed_headroom & needed_tailroom to avoid
copies. But its not enough, because many packets are cloned
before entering asix_tx_fixup() and this driver use skb_cloned()
as a lazy way to check if it can push and put additional bytes in frame.
Avoid skb_copy_expand() expensive call, using following rules :
- We are allowed to push 4 bytes in headroom if skb_header_cloned()
is false (and if we have 4 bytes of headroom)
- We are allowed to put 4 bytes at tail if skb_cloned()
is false (and if we have 4 bytes of tailroom)
TCP packets for example are cloned, but skb_header_release()
was called in tcp stack, allowing us to use headroom for our needs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Allan Chou <allan@asix.com.tw>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is easier to read if we specify which flags we want at the
condition instead of at the top of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the iPad to the ipheth driver.
(product id = 0x129a)
Signed-off-by: Davide Gerhard <rainbow@irh.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
If usbnet is resumed by remote wakeup, generally there are
some packets comming to be handled, so allocate and submit
rx URBs in usbnet_resume to avoid delays introduced by tasklet.
Otherwise, usbnet may have been runtime suspended before the
usbnet_bh is executed to schedule Rx URBs.
Without the patch, usbnet can't recieve any packets from peer
in runtime suspend state if runtime PM is enabled and
autosuspend_delay is set as zero.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decreases dev->suspend_count in the -EBUSY failure path
of usbnet_suspend. Without the change, the later runtime suspend
will do nothing except for increasing dev->suspend_count.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignoring interfaces with additional descriptors is not a reliable
method for locating the correct interface on Gobi devices. There
is at least one device where this method fails:
https://bbs.archlinux.org/viewtopic.php?id=143506
The result is that the AT command port (interface #2) is hidden
from qcserial, preventing traditional serial modem usage:
[ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device
[ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22
[ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device
[ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22
[ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected
[ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0
[ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected
[ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1
Use static interface numbers taken from the interface map in
qcserial for all Gobi devices instead:
Gobi 1K USB layout:
0: serial port (doesn't respond)
1: serial port (doesn't respond)
2: AT-capable modem port
3: QMI/net
Gobi 2K+ USB layout:
0: QMI/net
1: DM/DIAG (use libqcdm from ModemManager for communication)
2: AT-capable modem port
3: NMEA
This should be more reliable over all, and will also prevent the
noisy "probe failed" messages. The whitelisting logic is expected
to be replaced by direct interface number matching in 3.6.
Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de>
Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic
Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The description is used in ethtool fixed length fields. Make
it shorter to avoid truncation.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always bind to control interface regardless of whether
it is a shared interface or not.
A QMI/wwan function is required to provide both a control
interface (QMI) and a data interface (wwan). All devices
supported by this driver do so. But the vendors may
choose to use different USB descriptor layouts, and some
vendors even allow the same device to present different
layouts.
Most of these devices use a USB descriptor layout with a
single USB interface for both control and data. But some
split control and data into two interfaces, bound together
by a CDC Union descriptor on the control interface. Before
the cdc-wdm subdriver support was added, this split was
used to let cdc-wdm drive the QMI control interface and
qmi_wwan drive the wwna data interface.
This split driver model has a number of issues:
- qmi_wwan must match on the data interface descriptor,
which often are indistiguishable from data interfaces
belonging to other CDC (like) functions like ACM
- supporting a single QMI/wwan function requires adding
the device to two drivers
- syncronizing the probes among a number of drivers, to
ensure selecting the correct driver, is difficult unless
all drivers match on the same interface
This patch resolves these problems by using the same
probing mechanism as cdc-ether for devices with a two-
interface USB descriptor layout. This makes the driver
behave consistently, supporting both the control and data
part of the QMI/wwan function, regardless of the USB
descriptors.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the subdriver registration code can be reused for devices
with separate control and data interfaces. Move the code a bit
around to prepare for such reuse.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet allocates a fixed size array for minidriver specific
state. Naming the fields and taking advantage of type checking
is a bit more failsafe than casting array elements each time
they are referenced.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
As seen on smsc75xx, driver_info->description being longer than 32
characters messes up 'ethtool -i' output.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The line below in intr_complete isn't needed,
memset(urb->transfer_buffer, 0, urb->transfer_buffer_length);
so just remove it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove declaration for intr_complete so that ctags may be happy to
decrease duplicated symbols, also decrease one line code.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding device IDs for Aircard 320U and two other devices
found in the out-of-tree version of this driver.
Cc: linux@sierrawireless.com
Cc: Autif Khan <autif.mlist@gmail.com>
Cc: Tom Cassidy <tomas.cassidy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
asix driver drops 8021Q full size frames because it doesn't take into
account VLAN header size.
Tested on AX88772 adapter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Allan Chou <allan@asix.com.tw>
CC: Trond Wuellner <trond@chromium.org>
CC: Grant Grundler <grundler@chromium.org>
CC: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some additional Gobi3K IDs found in the BSD/GPL licensed
out-of-tree GobiNet driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as well.
We deleted a staging driver, which was nice, and finally dropped the
obsolete usbfs code, which will make Al happy to never have to touch
that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were due
to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
=4jM1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
Add the ZTE (Vodafone) K3765-Z to the whitelist. This requires the
previous patch to make the whitelist with forced interface 4 generic
or the device fails to initialise. After applying this patch and
loading the Option driver without usb-modeswitch's bind all
interfaces trick, a wwan0 net interface and /dev/cdc-wdm0 device
file were created. Using Bjorn Mork's perl connection script a
connection was made to a mobile network using QMI and the network
interface's IPv4 address was configured OK.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the forced interface 4 whitelist to use the generic shared
binder instead of the Gobi specific one. Certain ZTE devices
(K3520-Z & K3765-Z) don't work with the Gobi version, but function
quite happily with the generic. This has been tested with the following
devices:
K3520-Z
K3565-Z
K3765-Z
K4505-Z
It hasn't been tested with the ZTE MF820D, which is the only other
device that uses this whitelist at present. Although Bjorn doesn't
expect any problems, any testing with that device would be appreciated.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ZTE WWAN devices have generic CDC Ether descriptors. Add those
into the whitelist so that we get FLAG_WWAN on the interface
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Needs to be tagged with FLAG_WWAN, which since it has generic
descriptors, won't happen if we don't override the generic
driver info.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock before unlink, but may
cause skb traversing races:
- after URB is unlinked and the queue lock is released,
the refered skb and skb->next may be moved to done queue,
even be released
- in skb_queue_walk_safe, the next skb is still obtained
by next pointer of the last skb
- so maybe trigger oops or other problems
This patch extends the usage of entry->state to describe 'start_unlink'
state, so always holding the queue(rx/tx) lock to change the state if
the referd skb is in rx or tx queue because we need to know if the
refered urb has been started unlinking in unlink_urbs.
The other part of this patch is based on Huajun's patch:
always traverse from head of the tx/rx queue to get skb which is
to be unlinked but not been started unlinking.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other values from device provided buffer are byteswapped, so it seems
more logical to do same for these.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RNDIS protocol contains a vast number of Object ID:s (OIDs).
The current definitions had multiple definitions of these ID:s,
let's use the nicely RNDIS_*-prefixed defines from the HyperV
implementation, rename everywhere they're used, and copy+rename
the few that were missing from this list of objects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header file <linux/usb/rndis_host.h> used a number of #defines
that included the cpu_to_le32() macro to assure the result will be
in LE endianness. Inlining this into the code instead of using it
in the code definitions yields consolidation opportunities later
on as you will see in the following patches. The individual
drivers also used local defines - all are switched over to the
pattern of doing the conversion at the call sites instead.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the GPIO/LED settings to be configured by the
EEPROM if present, and only sets the default values (LED outputs
for link/activity) when an EEPROM is not detected.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only a write is necessary to clear the interrupt status, and we
don't use the value from the preceding read operation. This
patch eliminates the unnecessary read.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines PHY_INT_SRC_CLEAR_ALL to replace the value 0xffff
in order to be more self-documenting.
This patch should make no functional change, it is purely cosmetic.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some RNDIS devices include a bogus CDC Union descriptor pointing
to non-existing interfaces. The RNDIS code is already prepared
to handle devices without a CDC Union descriptor by hardwiring
the driver to use interfaces 0 and 1, which is correct for the
devices with the bogus descriptor as well. So we can reuse the
existing workaround.
Cc: Markus Kolb <linux-201011@tower-net.de>
Cc: Iker Salmón San Millán <shaola@esdebian.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: 655387@bugs.debian.org
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command. Both product ID
and USB interface configuration will change when switched.
The "sierra_net" driver supports the "Direct IP" mode. This driver
supports the "QMI" mode.
There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface. Like many other
devices made for Windows, different interface types are identified
using a static interface number. We define a Sierra specific
interface whitelist to support this.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc75xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Omap3 with EVB-LAN7500-LC.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We switched tty refcounting there to the one provided by tty_port
helpers. So tty_port->tty is now protected by tty_port->lock, not by
hso_serial->serial_lock.
Side note: tty->driver_data does not need the lock, so it is needed
neither in open, nor in close paths.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty is never NULL in tty->ops->* while the device is open. (And they
are not called otherwise.) So remove pointless checks and use
tty->driver_data directly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use open count from there. Other members will follow.
Remark: port.count is (and never was) properly protected. Only a mutex
is held, so ISR and all the functions it calls may see an invalid
state.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not leak tty_driver structure on each module removal. Also do
proper frees in fail paths of module_init.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is set in alloc_tty_driver already. No need to re-set.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make CDC EEM recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Tested with the Linux USB Ethernet gadget.
Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist duplicated macro definitions in rtl8150.c, remove them.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now skb_add_rx_frag() has a truesize parameter, we can fix cdc-phonet to
properly account truesize of each fragment : a full page.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be
recognized by the "zaurus" USBNet driver.
Applies to Linux 3.2.13 and 2.6.39.4.
Signed-off-by: Guan Xin <guanx.bac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_add_rx_frag() API is misleading.
Network skbs built with this helper can use uncharged kernel memory and
eventually stress/crash machine in OOM.
Add a 'truesize' parameter and then fix drivers in followup patches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the beginnings of an OSS method to use the network
interfaces on these USB broadband modems, add the ZTE manufactured
Vodafone items to the whitelist
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the beginnings of an OSS method to use the network
interfaces on these USB broadband modems, add the ZTE manufactured
Vodafone items to the whitelist
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet should centrally handle busy reporting in the rx path
so subdrivers need not worry. This hurts use cases which do
rx only or predominantly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.
Cc: stable@kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.
The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.
Cc: stable@kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty layer,
and a number of patches from Alan to help try to wrestle the vt layer
into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9nihQACgkQMUfUDdst+ylXTQCdFuwVuZgjCts+xDVa1jX2ac84
UogAn3Wr+P7NYFN6gvaGm52KbGbZs405
=2b/l
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
Fixes:
drivers/built-in.o: In function `qmi_wwan_bind_shared':
qmi_wwan.c:(.text+0x25b686): undefined reference to `usb_cdc_wdm_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If host is going to autosuspend function with two interfaces and
if IP packet has arrived in-between of two usbnet_suspend() callbacks,
i.e usbnet_resume() is called in-between, tx data flow is stopped.
When autosuspend timer expires and device is put to autosuspend
again, tx queue is waked up and data can be sent again.
This behavior might be repeated several times in a row.
Tested on Intel/ARM.
Reviewed-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ZTE have yet to discover the magic of USB descriptors. These
devices use ff/ff/ff for class/subclass/protocol regardless of
function, except for usb-storage. Use an interface number
whitelist to force the driver to bind only to the QMI/wwan
interface.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes:
- removed a limit for amount of datagrams for IN NTB
- using pointer to traverse NTB in rx_fixup()
- renamed "temp" to "len" in rx_fixup()
- do NTB sequence number check in rx path
Tested on Intel/ARM.
Reviewed-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Dmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes/fixes:
- inform device if max_datagram_size was changed by host
- max_datagram_size can't be bigger MTU in ETH func descr
- fix constants definitions to enable running CAIF service over NCM
Tested on Intel/ARM.
Reviewed-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Dmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes:
- use high resolution timer
latency became approx. 10-15 times less than before
- use taklet for sending remaining data in tx path
Tested on Intel/ARM.
Reviewed-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Dmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
network drivers should reserve some headroom on incoming skbs so that we
dont need expensive reallocations, eg forwarding packets in tunnels.
This NET_SKB_PAD padding is done in various helpers, like
__netdev_alloc_skb_ip_align() in this patch, combining NET_SKB_PAD and
NET_IP_ALIGN magic.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
asix_rx_fixup() is complex, and does some unnecessary memory copies (at
least on x86 where NET_IP_ALIGN is 0)
Also, it tends to provide skbs with a big truesize (4096+256 with
MTU=1500) to upper stack, so incoming trafic consume a lot of memory and
I noticed early packet drops because we hit socket rcvbuf too fast.
Switch to a different strategy, using copybreak so that we provide nice
skbs to upper stack (including the NET_SKB_PAD to avoid future head
reallocations in some paths)
With this patch, I no longer see packets drops or tcp collapses on
various tcp workload with a AX88772 adapter.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Aurelien Jacobs <aurel@gnuage.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the Pantech UML290 and all non-QDL Gobi device IDs from the
qcserial driver now that we have support for shared net/QMI USB
interfaces. Most of these are not yet tested with this driver, but
should be mostly identical to tested devices, except for device IDs.
Gobi devices provide several different interfaces (serial/net/other)
using the exact same class, subclass and protocol values. This driver
will only support the net/QMI function while there are other drivers
supporting other device functions. The net/QMI interface number may
also differ from device to device. It has been noted that all the
other interfaces have additional functional descriptors, so we use that
to detect the interface supported by this driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new cdc-wdm subdriver interface to create a device management
device even for USB devices having a single combined QMI/wwan USB
interface with three endpoints (int, bulk in, bulk out) instead of
separate data and control interfaces.
Some Huawei devices can be switched to a single interface mode for
use with other operating systems than Linux. This adds support
for these devices when they run in such non-Linux modes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)
defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.
Cc: stable@kernel.org
Reported-by: AnÃbal Almeida Pinto <anibal.pinto@efacec.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent was to clear out the icount struct here, but we accidentally
clear stack memory instead. It probably will lead to a NULL dereference
right away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 16adf5d079 I removed an over-broad
alias that caused zaurus.ko to bind to unrelated devices.
I had a report that at least one valid case no longer auto-loads because of this.
This patch adds an ID for that case.
Reported-by: Raphael Wimmer <raphael.wimmer@ur.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/900802
Cc: stable@vger.kernel.org 3.2+
Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel v3.2 initialization sequence for Asix 88178 devices was changed so
that hardware is reseted on every time interface is brought up (ifconfig up),
instead just at USB probe time. This causes problem with setting custom MAC
address to device as ax88178_reset causes reload of MAC address from EEPROM.
This patch fixes the issue by rewriting MAC address at end of ax88178_reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Grant Grundler <grundler@chromium.org>
Cc: Allan Chou <allan@asix.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel v3.2 initialization sequence for Asix 88772 devices was changed so
that hardware is reseted on every time interface is brought up (ifconfig up),
instead just at USB probe time. This causes problem with setting custom MAC
address to device as ax88772_reset causes reload of MAC address from EEPROM.
This patch fixes the issue by rewriting MAC address at end of ax88772_reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Grant Grundler <grundler@chromium.org>
Cc: Allan Chou <allan@asix.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
igmp: Avoid zero delay when receiving odd mixture of IGMP queries
netdev: make net_device_ops const
bcm63xx: make ethtool_ops const
usbnet: make ethtool_ops const
net: Fix build with INET disabled.
net: introduce netif_addr_lock_nested() and call if when appropriate
net: correct lock name in dev_[uc/mc]_sync documentations.
net: sk_update_clone is only used in net/core/sock.c
8139cp: fix missing napi_gro_flush.
pktgen: set correct max and min in pktgen_setup_inject()
smsc911x: Unconditionally include linux/smscphy.h in smsc911x.h
asix: fix infinite loop in rx_fixup()
net: Default UDP and UNIX diag to 'n'.
r6040: fix typo in use of MCR0 register bits
net: fix sock_clone reference mismatch with tcp memcontrol
The ethtool_ops table of function pointers should be const.
Fix all the usb network drivers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point if skb->len happens to be 2, the subsequant skb_pull(skb, 4)
call won't work and the skb->len won't be decreased and won't ever reach 0,
resulting in an infinite loop.
With an ASIX 88772 under heavy load, without this patch, rx_fixup() reaches
an infinite loop in less than a minute. With this patch applied,
no infinite loop even after hours of heavy load.
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently made loopback a bool type instead of an int, so the bitwise
AND is redundent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the asix_get_wol() routine reported wrong wol status issue.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Eugene <elubarsky@gmail.com>; Allan Chou <allan@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the device id needed for the USB Ethernet Adapter delivered by
ASUS with their Zenbook.
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Acked-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given we dont use anymore the struct net_device *dev argument, and this
interface brings litle benefit, remove netdev_{alloc|free}_page(), to
debloat include/linux/skbuff.h a bit.
(Some drivers used a mix of these interfaces and alloc_pages())
When allocating a page given to device for DMA transfer (device to
memory), it makes sense to use a cold one (__GFP_COLD)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
This converts the drivers in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Yoann DI-RUZZA <y.diruzza@lim.eu>
Cc: George <george0505@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only update VERSION to reflect previous changes.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now works on Samsung Series 5 (chromebook)
Two fixes here:
o use 0x7F mask for phymode
o read phyid *AFTER* phy is powered up (via GPIOs)
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the phy isn't ready after reset...poll and pray it will be soon.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
