52e405eaa9
The irgflags consolidation did conflict with the ARM to generic IRQ conversion and was not applied for ARM. Fix it up. Use the new IRQF_ constants and remove the SA_INTERRUPT define Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
288 lines
6.9 KiB
C
288 lines
6.9 KiB
C
/*
|
|
* linux/arch/arm/mach-omap1/id.c
|
|
*
|
|
* OMAP1 CPU identification code
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/serial.h>
|
|
#include <linux/tty.h>
|
|
#include <linux/serial_8250.h>
|
|
#include <linux/serial_reg.h>
|
|
#include <linux/clk.h>
|
|
|
|
#include <asm/io.h>
|
|
#include <asm/mach-types.h>
|
|
|
|
#include <asm/arch/board.h>
|
|
#include <asm/arch/mux.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/fpga.h>
|
|
#ifdef CONFIG_PM
|
|
#include <asm/arch/pm.h>
|
|
#endif
|
|
|
|
static struct clk * uart1_ck;
|
|
static struct clk * uart2_ck;
|
|
static struct clk * uart3_ck;
|
|
|
|
static inline unsigned int omap_serial_in(struct plat_serial8250_port *up,
|
|
int offset)
|
|
{
|
|
offset <<= up->regshift;
|
|
return (unsigned int)__raw_readb(up->membase + offset);
|
|
}
|
|
|
|
static inline void omap_serial_outp(struct plat_serial8250_port *p, int offset,
|
|
int value)
|
|
{
|
|
offset <<= p->regshift;
|
|
__raw_writeb(value, p->membase + offset);
|
|
}
|
|
|
|
/*
|
|
* Internal UARTs need to be initialized for the 8250 autoconfig to work
|
|
* properly. Note that the TX watermark initialization may not be needed
|
|
* once the 8250.c watermark handling code is merged.
|
|
*/
|
|
static void __init omap_serial_reset(struct plat_serial8250_port *p)
|
|
{
|
|
omap_serial_outp(p, UART_OMAP_MDR1, 0x07); /* disable UART */
|
|
omap_serial_outp(p, UART_OMAP_SCR, 0x08); /* TX watermark */
|
|
omap_serial_outp(p, UART_OMAP_MDR1, 0x00); /* enable UART */
|
|
|
|
if (!cpu_is_omap1510()) {
|
|
omap_serial_outp(p, UART_OMAP_SYSC, 0x01);
|
|
while (!(omap_serial_in(p, UART_OMAP_SYSC) & 0x01));
|
|
}
|
|
}
|
|
|
|
static struct plat_serial8250_port serial_platform_data[] = {
|
|
{
|
|
.membase = (char*)IO_ADDRESS(OMAP_UART1_BASE),
|
|
.mapbase = (unsigned long)OMAP_UART1_BASE,
|
|
.irq = INT_UART1,
|
|
.flags = UPF_BOOT_AUTOCONF,
|
|
.iotype = UPIO_MEM,
|
|
.regshift = 2,
|
|
.uartclk = OMAP16XX_BASE_BAUD * 16,
|
|
},
|
|
{
|
|
.membase = (char*)IO_ADDRESS(OMAP_UART2_BASE),
|
|
.mapbase = (unsigned long)OMAP_UART2_BASE,
|
|
.irq = INT_UART2,
|
|
.flags = UPF_BOOT_AUTOCONF,
|
|
.iotype = UPIO_MEM,
|
|
.regshift = 2,
|
|
.uartclk = OMAP16XX_BASE_BAUD * 16,
|
|
},
|
|
{
|
|
.membase = (char*)IO_ADDRESS(OMAP_UART3_BASE),
|
|
.mapbase = (unsigned long)OMAP_UART3_BASE,
|
|
.irq = INT_UART3,
|
|
.flags = UPF_BOOT_AUTOCONF,
|
|
.iotype = UPIO_MEM,
|
|
.regshift = 2,
|
|
.uartclk = OMAP16XX_BASE_BAUD * 16,
|
|
},
|
|
{ },
|
|
};
|
|
|
|
static struct platform_device serial_device = {
|
|
.name = "serial8250",
|
|
.id = PLAT8250_DEV_PLATFORM,
|
|
.dev = {
|
|
.platform_data = serial_platform_data,
|
|
},
|
|
};
|
|
|
|
/*
|
|
* Note that on Innovator-1510 UART2 pins conflict with USB2.
|
|
* By default UART2 does not work on Innovator-1510 if you have
|
|
* USB OHCI enabled. To use UART2, you must disable USB2 first.
|
|
*/
|
|
void __init omap_serial_init(void)
|
|
{
|
|
int i;
|
|
const struct omap_uart_config *info;
|
|
|
|
if (cpu_is_omap730()) {
|
|
serial_platform_data[0].regshift = 0;
|
|
serial_platform_data[1].regshift = 0;
|
|
serial_platform_data[0].irq = INT_730_UART_MODEM_1;
|
|
serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
|
|
}
|
|
|
|
if (cpu_is_omap1510()) {
|
|
serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
|
|
serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
|
|
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
|
|
}
|
|
|
|
info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
|
|
if (info == NULL)
|
|
return;
|
|
|
|
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
|
|
unsigned char reg;
|
|
|
|
if (!((1 << i) & info->enabled_uarts)) {
|
|
serial_platform_data[i].membase = NULL;
|
|
serial_platform_data[i].mapbase = 0;
|
|
continue;
|
|
}
|
|
|
|
switch (i) {
|
|
case 0:
|
|
uart1_ck = clk_get(NULL, "uart1_ck");
|
|
if (IS_ERR(uart1_ck))
|
|
printk("Could not get uart1_ck\n");
|
|
else {
|
|
clk_enable(uart1_ck);
|
|
if (cpu_is_omap1510())
|
|
clk_set_rate(uart1_ck, 12000000);
|
|
}
|
|
if (cpu_is_omap1510()) {
|
|
omap_cfg_reg(UART1_TX);
|
|
omap_cfg_reg(UART1_RTS);
|
|
if (machine_is_omap_innovator()) {
|
|
reg = fpga_read(OMAP1510_FPGA_POWER);
|
|
reg |= OMAP1510_FPGA_PCR_COM1_EN;
|
|
fpga_write(reg, OMAP1510_FPGA_POWER);
|
|
udelay(10);
|
|
}
|
|
}
|
|
break;
|
|
case 1:
|
|
uart2_ck = clk_get(NULL, "uart2_ck");
|
|
if (IS_ERR(uart2_ck))
|
|
printk("Could not get uart2_ck\n");
|
|
else {
|
|
clk_enable(uart2_ck);
|
|
if (cpu_is_omap1510())
|
|
clk_set_rate(uart2_ck, 12000000);
|
|
else
|
|
clk_set_rate(uart2_ck, 48000000);
|
|
}
|
|
if (cpu_is_omap1510()) {
|
|
omap_cfg_reg(UART2_TX);
|
|
omap_cfg_reg(UART2_RTS);
|
|
if (machine_is_omap_innovator()) {
|
|
reg = fpga_read(OMAP1510_FPGA_POWER);
|
|
reg |= OMAP1510_FPGA_PCR_COM2_EN;
|
|
fpga_write(reg, OMAP1510_FPGA_POWER);
|
|
udelay(10);
|
|
}
|
|
}
|
|
break;
|
|
case 2:
|
|
uart3_ck = clk_get(NULL, "uart3_ck");
|
|
if (IS_ERR(uart3_ck))
|
|
printk("Could not get uart3_ck\n");
|
|
else {
|
|
clk_enable(uart3_ck);
|
|
if (cpu_is_omap1510())
|
|
clk_set_rate(uart3_ck, 12000000);
|
|
}
|
|
if (cpu_is_omap1510()) {
|
|
omap_cfg_reg(UART3_TX);
|
|
omap_cfg_reg(UART3_RX);
|
|
}
|
|
break;
|
|
}
|
|
omap_serial_reset(&serial_platform_data[i]);
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_OMAP_SERIAL_WAKE
|
|
|
|
static irqreturn_t omap_serial_wake_interrupt(int irq, void *dev_id,
|
|
struct pt_regs *regs)
|
|
{
|
|
/* Need to do something with serial port right after wake-up? */
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
/*
|
|
* Reroutes serial RX lines to GPIO lines for the duration of
|
|
* sleep to allow waking up the device from serial port even
|
|
* in deep sleep.
|
|
*/
|
|
void omap_serial_wake_trigger(int enable)
|
|
{
|
|
if (!cpu_is_omap16xx())
|
|
return;
|
|
|
|
if (uart1_ck != NULL) {
|
|
if (enable)
|
|
omap_cfg_reg(V14_16XX_GPIO37);
|
|
else
|
|
omap_cfg_reg(V14_16XX_UART1_RX);
|
|
}
|
|
if (uart2_ck != NULL) {
|
|
if (enable)
|
|
omap_cfg_reg(R9_16XX_GPIO18);
|
|
else
|
|
omap_cfg_reg(R9_16XX_UART2_RX);
|
|
}
|
|
if (uart3_ck != NULL) {
|
|
if (enable)
|
|
omap_cfg_reg(L14_16XX_GPIO49);
|
|
else
|
|
omap_cfg_reg(L14_16XX_UART3_RX);
|
|
}
|
|
}
|
|
|
|
static void __init omap_serial_set_port_wakeup(int gpio_nr)
|
|
{
|
|
int ret;
|
|
|
|
ret = omap_request_gpio(gpio_nr);
|
|
if (ret < 0) {
|
|
printk(KERN_ERR "Could not request UART wake GPIO: %i\n",
|
|
gpio_nr);
|
|
return;
|
|
}
|
|
omap_set_gpio_direction(gpio_nr, 1);
|
|
ret = request_irq(OMAP_GPIO_IRQ(gpio_nr), &omap_serial_wake_interrupt,
|
|
IRQF_TRIGGER_RISING, "serial wakeup", NULL);
|
|
if (ret) {
|
|
omap_free_gpio(gpio_nr);
|
|
printk(KERN_ERR "No interrupt for UART wake GPIO: %i\n",
|
|
gpio_nr);
|
|
return;
|
|
}
|
|
enable_irq_wake(OMAP_GPIO_IRQ(gpio_nr));
|
|
}
|
|
|
|
static int __init omap_serial_wakeup_init(void)
|
|
{
|
|
if (!cpu_is_omap16xx())
|
|
return 0;
|
|
|
|
if (uart1_ck != NULL)
|
|
omap_serial_set_port_wakeup(37);
|
|
if (uart2_ck != NULL)
|
|
omap_serial_set_port_wakeup(18);
|
|
if (uart3_ck != NULL)
|
|
omap_serial_set_port_wakeup(49);
|
|
|
|
return 0;
|
|
}
|
|
late_initcall(omap_serial_wakeup_init);
|
|
|
|
#endif /* CONFIG_OMAP_SERIAL_WAKE */
|
|
|
|
static int __init omap_init(void)
|
|
{
|
|
return platform_device_register(&serial_device);
|
|
}
|
|
arch_initcall(omap_init);
|