a982ac06b0
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4. Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
131 lines
5.4 KiB
Text
131 lines
5.4 KiB
Text
Platform Devices and Drivers
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
See <linux/platform_device.h> for the driver model interface to the
|
|
platform bus: platform_device, and platform_driver. This pseudo-bus
|
|
is used to connect devices on busses with minimal infrastructure,
|
|
like those used to integrate peripherals on many system-on-chip
|
|
processors, or some "legacy" PC interconnects; as opposed to large
|
|
formally specified ones like PCI or USB.
|
|
|
|
|
|
Platform devices
|
|
~~~~~~~~~~~~~~~~
|
|
Platform devices are devices that typically appear as autonomous
|
|
entities in the system. This includes legacy port-based devices and
|
|
host bridges to peripheral buses, and most controllers integrated
|
|
into system-on-chip platforms. What they usually have in common
|
|
is direct addressing from a CPU bus. Rarely, a platform_device will
|
|
be connected through a segment of some other kind of bus; but its
|
|
registers will still be directly addressable.
|
|
|
|
Platform devices are given a name, used in driver binding, and a
|
|
list of resources such as addresses and IRQs.
|
|
|
|
struct platform_device {
|
|
const char *name;
|
|
u32 id;
|
|
struct device dev;
|
|
u32 num_resources;
|
|
struct resource *resource;
|
|
};
|
|
|
|
|
|
Platform drivers
|
|
~~~~~~~~~~~~~~~~
|
|
Platform drivers follow the standard driver model convention, where
|
|
discovery/enumeration is handled outside the drivers, and drivers
|
|
provide probe() and remove() methods. They support power management
|
|
and shutdown notifications using the standard conventions.
|
|
|
|
struct platform_driver {
|
|
int (*probe)(struct platform_device *);
|
|
int (*remove)(struct platform_device *);
|
|
void (*shutdown)(struct platform_device *);
|
|
int (*suspend)(struct platform_device *, pm_message_t state);
|
|
int (*suspend_late)(struct platform_device *, pm_message_t state);
|
|
int (*resume_early)(struct platform_device *);
|
|
int (*resume)(struct platform_device *);
|
|
struct device_driver driver;
|
|
};
|
|
|
|
Note that probe() should general verify that the specified device hardware
|
|
actually exists; sometimes platform setup code can't be sure. The probing
|
|
can use device resources, including clocks, and device platform_data.
|
|
|
|
Platform drivers register themselves the normal way:
|
|
|
|
int platform_driver_register(struct platform_driver *drv);
|
|
|
|
Or, in common situations where the device is known not to be hot-pluggable,
|
|
the probe() routine can live in an init section to reduce the driver's
|
|
runtime memory footprint:
|
|
|
|
int platform_driver_probe(struct platform_driver *drv,
|
|
int (*probe)(struct platform_device *))
|
|
|
|
|
|
Device Enumeration
|
|
~~~~~~~~~~~~~~~~~~
|
|
As a rule, platform specific (and often board-specific) setup code will
|
|
register platform devices:
|
|
|
|
int platform_device_register(struct platform_device *pdev);
|
|
|
|
int platform_add_devices(struct platform_device **pdevs, int ndev);
|
|
|
|
The general rule is to register only those devices that actually exist,
|
|
but in some cases extra devices might be registered. For example, a kernel
|
|
might be configured to work with an external network adapter that might not
|
|
be populated on all boards, or likewise to work with an integrated controller
|
|
that some boards might not hook up to any peripherals.
|
|
|
|
In some cases, boot firmware will export tables describing the devices
|
|
that are populated on a given board. Without such tables, often the
|
|
only way for system setup code to set up the correct devices is to build
|
|
a kernel for a specific target board. Such board-specific kernels are
|
|
common with embedded and custom systems development.
|
|
|
|
In many cases, the memory and IRQ resources associated with the platform
|
|
device are not enough to let the device's driver work. Board setup code
|
|
will often provide additional information using the device's platform_data
|
|
field to hold additional information.
|
|
|
|
Embedded systems frequently need one or more clocks for platform devices,
|
|
which are normally kept off until they're actively needed (to save power).
|
|
System setup also associates those clocks with the device, so that that
|
|
calls to clk_get(&pdev->dev, clock_name) return them as needed.
|
|
|
|
|
|
Device Naming and Driver Binding
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
The platform_device.dev.bus_id is the canonical name for the devices.
|
|
It's built from two components:
|
|
|
|
* platform_device.name ... which is also used to for driver matching.
|
|
|
|
* platform_device.id ... the device instance number, or else "-1"
|
|
to indicate there's only one.
|
|
|
|
These are concatenated, so name/id "serial"/0 indicates bus_id "serial.0", and
|
|
"serial/3" indicates bus_id "serial.3"; both would use the platform_driver
|
|
named "serial". While "my_rtc"/-1 would be bus_id "my_rtc" (no instance id)
|
|
and use the platform_driver called "my_rtc".
|
|
|
|
Driver binding is performed automatically by the driver core, invoking
|
|
driver probe() after finding a match between device and driver. If the
|
|
probe() succeeds, the driver and device are bound as usual. There are
|
|
three different ways to find such a match:
|
|
|
|
- Whenever a device is registered, the drivers for that bus are
|
|
checked for matches. Platform devices should be registered very
|
|
early during system boot.
|
|
|
|
- When a driver is registered using platform_driver_register(), all
|
|
unbound devices on that bus are checked for matches. Drivers
|
|
usually register later during booting, or by module loading.
|
|
|
|
- Registering a driver using platform_driver_probe() works just like
|
|
using platform_driver_register(), except that the driver won't
|
|
be probed later if another device registers. (Which is OK, since
|
|
this interface is only for use with non-hotpluggable devices.)
|
|
|