f9262c12c0
ATI chipsets tend to generate double timer interrupts for the local APIC timer when both the 8254 and the IO-APIC timer pins are enabled. This is because they route it to both and the result is anded together and the CPU ends up processing it twice. This patch changes check_timer to disable the 8254 routing for interrupt 0. I think it would be safe on all chipsets actually (i tested it on a couple and it worked everywhere) and Windows seems to do it in a similar way, but to be conservative this patch only enables this mode on ATI (and adds options to enable/disable too) Ported over from a similar x86-64 change. I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but tweaked it a bit to work even without ACPI. Inspired by a patch from Chuck Ebbert, but redone. Cc: Chuck Ebbert <76306.1226@compuserve.com> Cc: "Brown, Len" <len.brown@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
78 lines
2.8 KiB
Makefile
78 lines
2.8 KiB
Makefile
#
|
|
# Makefile for the linux kernel.
|
|
#
|
|
|
|
extra-y := head.o init_task.o vmlinux.lds
|
|
|
|
obj-y := process.o semaphore.o signal.o entry.o traps.o irq.o \
|
|
ptrace.o time.o ioport.o ldt.o setup.o i8259.o sys_i386.o \
|
|
pci-dma.o i386_ksyms.o i387.o dmi_scan.o bootflag.o \
|
|
quirks.o i8237.o topology.o
|
|
|
|
obj-y += cpu/
|
|
obj-y += timers/
|
|
obj-y += acpi/
|
|
obj-$(CONFIG_X86_BIOS_REBOOT) += reboot.o
|
|
obj-$(CONFIG_MCA) += mca.o
|
|
obj-$(CONFIG_X86_MSR) += msr.o
|
|
obj-$(CONFIG_X86_CPUID) += cpuid.o
|
|
obj-$(CONFIG_MICROCODE) += microcode.o
|
|
obj-$(CONFIG_APM) += apm.o
|
|
obj-$(CONFIG_X86_SMP) += smp.o smpboot.o
|
|
obj-$(CONFIG_X86_TRAMPOLINE) += trampoline.o
|
|
obj-$(CONFIG_X86_MPPARSE) += mpparse.o
|
|
obj-$(CONFIG_X86_LOCAL_APIC) += apic.o nmi.o
|
|
obj-$(CONFIG_X86_IO_APIC) += io_apic.o
|
|
obj-$(CONFIG_X86_REBOOTFIXUPS) += reboot_fixups.o
|
|
obj-$(CONFIG_KEXEC) += machine_kexec.o relocate_kernel.o crash.o
|
|
obj-$(CONFIG_CRASH_DUMP) += crash_dump.o
|
|
obj-$(CONFIG_X86_NUMAQ) += numaq.o
|
|
obj-$(CONFIG_X86_SUMMIT_NUMA) += summit.o
|
|
obj-$(CONFIG_KPROBES) += kprobes.o
|
|
obj-$(CONFIG_MODULES) += module.o
|
|
obj-y += sysenter.o vsyscall.o
|
|
obj-$(CONFIG_ACPI_SRAT) += srat.o
|
|
obj-$(CONFIG_HPET_TIMER) += time_hpet.o
|
|
obj-$(CONFIG_EFI) += efi.o efi_stub.o
|
|
obj-$(CONFIG_DOUBLEFAULT) += doublefault.o
|
|
obj-$(CONFIG_VM86) += vm86.o
|
|
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
|
|
|
|
EXTRA_AFLAGS := -traditional
|
|
|
|
obj-$(CONFIG_SCx200) += scx200.o
|
|
|
|
# vsyscall.o contains the vsyscall DSO images as __initdata.
|
|
# We must build both images before we can assemble it.
|
|
# Note: kbuild does not track this dependency due to usage of .incbin
|
|
$(obj)/vsyscall.o: $(obj)/vsyscall-int80.so $(obj)/vsyscall-sysenter.so
|
|
targets += $(foreach F,int80 sysenter,vsyscall-$F.o vsyscall-$F.so)
|
|
targets += vsyscall-note.o vsyscall.lds
|
|
|
|
# The DSO images are built using a special linker script.
|
|
quiet_cmd_syscall = SYSCALL $@
|
|
cmd_syscall = $(CC) -m elf_i386 -nostdlib $(SYSCFLAGS_$(@F)) \
|
|
-Wl,-T,$(filter-out FORCE,$^) -o $@
|
|
|
|
export CPPFLAGS_vsyscall.lds += -P -C -U$(ARCH)
|
|
|
|
vsyscall-flags = -shared -s -Wl,-soname=linux-gate.so.1
|
|
SYSCFLAGS_vsyscall-sysenter.so = $(vsyscall-flags)
|
|
SYSCFLAGS_vsyscall-int80.so = $(vsyscall-flags)
|
|
|
|
$(obj)/vsyscall-int80.so $(obj)/vsyscall-sysenter.so: \
|
|
$(obj)/vsyscall-%.so: $(src)/vsyscall.lds \
|
|
$(obj)/vsyscall-%.o $(obj)/vsyscall-note.o FORCE
|
|
$(call if_changed,syscall)
|
|
|
|
# We also create a special relocatable object that should mirror the symbol
|
|
# table and layout of the linked DSO. With ld -R we can then refer to
|
|
# these symbols in the kernel code rather than hand-coded addresses.
|
|
extra-y += vsyscall-syms.o
|
|
$(obj)/built-in.o: $(obj)/vsyscall-syms.o
|
|
$(obj)/built-in.o: ld_flags += -R $(obj)/vsyscall-syms.o
|
|
|
|
SYSCFLAGS_vsyscall-syms.o = -r
|
|
$(obj)/vsyscall-syms.o: $(src)/vsyscall.lds \
|
|
$(obj)/vsyscall-sysenter.o $(obj)/vsyscall-note.o FORCE
|
|
$(call if_changed,syscall)
|