210 lines
5.6 KiB
ArmAsm
210 lines
5.6 KiB
ArmAsm
; WARNING : The refill handler has been modified, see below !!!
|
|
|
|
/*
|
|
* Copyright (C) 2003 Axis Communications AB
|
|
*
|
|
* Authors: Mikael Starvik (starvik@axis.com)
|
|
*
|
|
* Code for the fault low-level handling routines.
|
|
*
|
|
*/
|
|
|
|
#include <asm/page.h>
|
|
#include <asm/pgtable.h>
|
|
|
|
; Save all register. Must save in same order as struct pt_regs.
|
|
.macro SAVE_ALL
|
|
subq 12, $sp
|
|
move $erp, [$sp]
|
|
subq 4, $sp
|
|
move $srp, [$sp]
|
|
subq 4, $sp
|
|
move $ccs, [$sp]
|
|
subq 4, $sp
|
|
move $spc, [$sp]
|
|
subq 4, $sp
|
|
move $mof, [$sp]
|
|
subq 4, $sp
|
|
move $srs, [$sp]
|
|
subq 4, $sp
|
|
move.d $acr, [$sp]
|
|
subq 14*4, $sp
|
|
movem $r13, [$sp]
|
|
subq 4, $sp
|
|
move.d $r10, [$sp]
|
|
.endm
|
|
|
|
; Bus fault handler. Extracts relevant information and calls mm subsystem
|
|
; to handle the fault.
|
|
.macro MMU_BUS_FAULT_HANDLER handler, mmu, we, ex
|
|
.globl \handler
|
|
\handler:
|
|
SAVE_ALL
|
|
move \mmu, $srs ; Select MMU support register bank
|
|
move.d $sp, $r11 ; regs
|
|
moveq 1, $r12 ; protection fault
|
|
moveq \we, $r13 ; write exception?
|
|
orq \ex << 1, $r13 ; execute?
|
|
move $s3, $r10 ; rw_mm_cause
|
|
and.d ~8191, $r10 ; Get faulting page start address
|
|
|
|
jsr do_page_fault
|
|
nop
|
|
ba ret_from_intr
|
|
nop
|
|
.endm
|
|
|
|
; Refill handler. Three cases may occur:
|
|
; 1. PMD and PTE exists in mm subsystem but not in TLB
|
|
; 2. PMD exists but not PTE
|
|
; 3. PMD doesn't exist
|
|
; The code below handles case 1 and calls the mm subsystem for case 2 and 3.
|
|
; Do not touch this code without very good reasons and extensive testing.
|
|
; Note that the code is optimized to minimize stalls (makes the code harder
|
|
; to read).
|
|
;
|
|
; WARNING !!!
|
|
; Modified by Mikael Asker 060725: added a workaround for strange TLB
|
|
; behavior. If the same PTE is present in more than one set, the TLB
|
|
; doesn't recognize it and we get stuck in a loop of refill exceptions.
|
|
; The workaround detects such loops and exits them by flushing
|
|
; the TLB contents. The problem and workaround were verified
|
|
; in VCS by Mikael Starvik.
|
|
;
|
|
; Each page is 8 KB. Each PMD holds 8192/4 PTEs (each PTE is 4 bytes) so each
|
|
; PMD holds 16 MB of virtual memory.
|
|
; Bits 0-12 : Offset within a page
|
|
; Bits 13-23 : PTE offset within a PMD
|
|
; Bits 24-31 : PMD offset within the PGD
|
|
|
|
.macro MMU_REFILL_HANDLER handler, mmu
|
|
.data
|
|
1: .dword 0 ; refill_count
|
|
; == 0 <=> last_refill_cause is invalid
|
|
2: .dword 0 ; last_refill_cause
|
|
.text
|
|
.globl \handler
|
|
\handler:
|
|
subq 4, $sp
|
|
; (The pipeline stalls for one cycle; $sp used as address in the next cycle.)
|
|
move $srs, [$sp]
|
|
subq 4, $sp
|
|
move \mmu, $srs ; Select MMU support register bank
|
|
move.d $acr, [$sp]
|
|
subq 12, $sp
|
|
move.d 1b, $acr ; Point to refill_count
|
|
movem $r2, [$sp]
|
|
|
|
test.d [$acr] ; refill_count == 0 ?
|
|
beq 5f ; yes, last_refill_cause is invalid
|
|
move.d $acr, $r1
|
|
|
|
; last_refill_cause is valid, investigate cause
|
|
addq 4, $r1 ; Point to last_refill_cause
|
|
move $s3, $r0 ; Get rw_mm_cause
|
|
move.d [$r1], $r2 ; Get last_refill_cause
|
|
cmp.d $r0, $r2 ; rw_mm_cause == last_refill_cause ?
|
|
beq 6f ; yes, increment count
|
|
moveq 1, $r2
|
|
|
|
; rw_mm_cause != last_refill_cause
|
|
move.d $r2, [$acr] ; refill_count = 1
|
|
move.d $r0, [$r1] ; last_refill_cause = rw_mm_cause
|
|
|
|
3: ; Probably not in a loop, continue normal processing
|
|
#ifdef CONFIG_SMP
|
|
move $s7, $acr ; PGD
|
|
#else
|
|
move.d per_cpu__current_pgd, $acr ; PGD
|
|
#endif
|
|
; Look up PMD in PGD
|
|
lsrq 24, $r0 ; Get PMD index into PGD (bit 24-31)
|
|
move.d [$acr], $acr ; PGD for the current process
|
|
addi $r0.d, $acr, $acr
|
|
move $s3, $r0 ; rw_mm_cause
|
|
move.d [$acr], $acr ; Get PMD
|
|
beq 8f
|
|
; Look up PTE in PMD
|
|
lsrq PAGE_SHIFT, $r0
|
|
and.w PAGE_MASK, $acr ; Remove PMD flags
|
|
and.d 0x7ff, $r0 ; Get PTE index into PMD (bit 13-23)
|
|
addi $r0.d, $acr, $acr
|
|
move.d [$acr], $acr ; Get PTE
|
|
beq 9f
|
|
movem [$sp], $r2 ; Restore r0-r2 in delay slot
|
|
addq 12, $sp
|
|
; Store in TLB
|
|
move $acr, $s5
|
|
4: ; Return
|
|
move.d [$sp+], $acr
|
|
move [$sp], $srs
|
|
addq 4, $sp
|
|
rete
|
|
rfe
|
|
|
|
5: ; last_refill_cause is invalid
|
|
moveq 1, $r2
|
|
addq 4, $r1 ; Point to last_refill_cause
|
|
move.d $r2, [$acr] ; refill_count = 1
|
|
move $s3, $r0 ; Get rw_mm_cause
|
|
ba 3b ; Continue normal processing
|
|
move.d $r0,[$r1] ; last_refill_cause = rw_mm_cause
|
|
|
|
6: ; rw_mm_cause == last_refill_cause
|
|
move.d [$acr], $r2 ; Get refill_count
|
|
cmpq 4, $r2 ; refill_count > 4 ?
|
|
bhi 7f ; yes
|
|
addq 1, $r2 ; refill_count++
|
|
ba 3b ; Continue normal processing
|
|
move.d $r2, [$acr]
|
|
|
|
7: ; refill_count > 4, error
|
|
move.d $acr, $r0 ; Save pointer to refill_count
|
|
clear.d [$r0] ; refill_count = 0
|
|
|
|
;; rewind the short stack
|
|
movem [$sp], $r2 ; Restore r0-r2
|
|
addq 12, $sp
|
|
move.d [$sp+], $acr
|
|
move [$sp], $srs
|
|
addq 4, $sp
|
|
;; Keep it simple (slow), save all the regs.
|
|
SAVE_ALL
|
|
jsr __flush_tlb_all
|
|
nop
|
|
ba ret_from_intr ; Return
|
|
nop
|
|
|
|
8: ; PMD missing, let the mm subsystem fix it up.
|
|
movem [$sp], $r2 ; Restore r0-r2
|
|
9: ; PTE missing, let the mm subsystem fix it up.
|
|
addq 12, $sp
|
|
move.d [$sp+], $acr
|
|
move [$sp], $srs
|
|
addq 4, $sp
|
|
SAVE_ALL
|
|
move \mmu, $srs
|
|
move.d $sp, $r11 ; regs
|
|
clear.d $r12 ; Not a protection fault
|
|
move.w PAGE_MASK, $acr
|
|
move $s3, $r10 ; rw_mm_cause
|
|
btstq 9, $r10 ; Check if write access
|
|
smi $r13
|
|
and.w PAGE_MASK, $r10 ; Get VPN (virtual address)
|
|
jsr do_page_fault
|
|
and.w $acr, $r10
|
|
; Return
|
|
ba ret_from_intr
|
|
nop
|
|
.endm
|
|
|
|
; This is the MMU bus fault handlers.
|
|
|
|
MMU_REFILL_HANDLER i_mmu_refill, 1
|
|
MMU_BUS_FAULT_HANDLER i_mmu_invalid, 1, 0, 0
|
|
MMU_BUS_FAULT_HANDLER i_mmu_access, 1, 0, 0
|
|
MMU_BUS_FAULT_HANDLER i_mmu_execute, 1, 0, 1
|
|
MMU_REFILL_HANDLER d_mmu_refill, 2
|
|
MMU_BUS_FAULT_HANDLER d_mmu_invalid, 2, 0, 0
|
|
MMU_BUS_FAULT_HANDLER d_mmu_access, 2, 0, 0
|
|
MMU_BUS_FAULT_HANDLER d_mmu_write, 2, 1, 0
|