a63ad325c3
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
96 lines
3.6 KiB
Text
96 lines
3.6 KiB
Text
This page describes the structures and procedures used by the cx2341x DMA
|
|
engine.
|
|
|
|
Introduction
|
|
============
|
|
|
|
The cx2341x PCI interface is busmaster capable. This means it has a DMA
|
|
engine to efficiently transfer large volumes of data between the card and main
|
|
memory without requiring help from a CPU. Like most hardware, it must operate
|
|
on contiguous physical memory. This is difficult to come by in large quantities
|
|
on virtual memory machines.
|
|
|
|
Therefore, it also supports a technique called "scatter-gather". The card can
|
|
transfer multiple buffers in one operation. Instead of allocating one large
|
|
contiguous buffer, the driver can allocate several smaller buffers.
|
|
|
|
In practice, I've seen the average transfer to be roughly 80K, but transfers
|
|
above 128K were not uncommon, particularly at startup. The 128K figure is
|
|
important, because that is the largest block that the kernel can normally
|
|
allocate. Even still, 128K blocks are hard to come by, so the driver writer is
|
|
urged to choose a smaller block size and learn the scatter-gather technique.
|
|
|
|
Mailbox #10 is reserved for DMA transfer information.
|
|
|
|
Note: the hardware expects little-endian data ('intel format').
|
|
|
|
Flow
|
|
====
|
|
|
|
This section describes, in general, the order of events when handling DMA
|
|
transfers. Detailed information follows this section.
|
|
|
|
- The card raises the Encoder interrupt.
|
|
- The driver reads the transfer type, offset and size from Mailbox #10.
|
|
- The driver constructs the scatter-gather array from enough free dma buffers
|
|
to cover the size.
|
|
- The driver schedules the DMA transfer via the ScheduleDMAtoHost API call.
|
|
- The card raises the DMA Complete interrupt.
|
|
- The driver checks the DMA status register for any errors.
|
|
- The driver post-processes the newly transferred buffers.
|
|
|
|
NOTE! It is possible that the Encoder and DMA Complete interrupts get raised
|
|
simultaneously. (End of the last, start of the next, etc.)
|
|
|
|
Mailbox #10
|
|
===========
|
|
|
|
The Flags, Command, Return Value and Timeout fields are ignored.
|
|
|
|
Name: Mailbox #10
|
|
Results[0]: Type: 0: MPEG.
|
|
Results[1]: Offset: The position relative to the card's memory space.
|
|
Results[2]: Size: The exact number of bytes to transfer.
|
|
|
|
My speculation is that since the StartCapture API has a capture type of "RAW"
|
|
available, that the type field will have other values that correspond to YUV
|
|
and PCM data.
|
|
|
|
Scatter-Gather Array
|
|
====================
|
|
|
|
The scatter-gather array is a contiguously allocated block of memory that
|
|
tells the card the source and destination of each data-block to transfer.
|
|
Card "addresses" are derived from the offset supplied by Mailbox #10. Host
|
|
addresses are the physical memory location of the target DMA buffer.
|
|
|
|
Each S-G array element is a struct of three 32-bit words. The first word is
|
|
the source address, the second is the destination address. Both take up the
|
|
entire 32 bits. The lowest 18 bits of the third word is the transfer byte
|
|
count. The high-bit of the third word is the "last" flag. The last-flag tells
|
|
the card to raise the DMA_DONE interrupt. From hard personal experience, if
|
|
you forget to set this bit, the card will still "work" but the stream will
|
|
most likely get corrupted.
|
|
|
|
The transfer count must be a multiple of 256. Therefore, the driver will need
|
|
to track how much data in the target buffer is valid and deal with it
|
|
accordingly.
|
|
|
|
Array Element:
|
|
|
|
- 32-bit Source Address
|
|
- 32-bit Destination Address
|
|
- 14-bit reserved (high bit is the last flag)
|
|
- 18-bit byte count
|
|
|
|
DMA Transfer Status
|
|
===================
|
|
|
|
Register 0x0004 holds the DMA Transfer Status:
|
|
|
|
Bit
|
|
0 read completed
|
|
1 write completed
|
|
2 DMA read error
|
|
3 DMA write error
|
|
4 Scatter-Gather array error
|