asgardius/android_kernel_motorola_sm6225
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
android_kernel_motorola_sm6225/include/linux/mmc/host.h
Veerabhadrarao Badiganti e102e0967f mmc: host: Reset sdhc-crypto engine only during error recovery 
No need to reset the inline-crypto-engine (ICE) when SDHC soft-
reset is triggered. ICE needs to be reset only when SDHC gets h/w
reset (this is to keep SHDC and ICE in sync) but mmc driver never
does h/w reset of SDHC controller

Resetting ICE whenever SDHC get soft reset (in suspend path)
resulting in TZ calls and causing latency issues.

But invoke ice reset during error handling path to ensure ice
s/w state machine is in sync with the mmc s/w state.

Change-Id: Ifb48bf215821a8318520e214370c78f2bc857622
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Ram Prakash Gupta <rampraka@codeaurora.org>
2019-08-02 16:09:01 +05:30

823 lines
27 KiB
C
Raw Blame History

/*
* linux/include/linux/mmc/host.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Host driver specific definitions.
*/
#ifndef LINUX_MMC_HOST_H
#define LINUX_MMC_HOST_H
#include <linux/sched.h>
#include <linux/device.h>
#include <linux/devfreq.h>
#include <linux/fault-inject.h>
#include <linux/blkdev.h>
#include <linux/extcon.h>
#include <linux/ipc_logging.h>
#include <linux/mmc/core.h>
#include <linux/mmc/card.h>
#include <linux/mmc/pm.h>
#include <linux/dma-direction.h>
#define MMC_AUTOSUSPEND_DELAY_MS 3000
struct mmc_ios {
unsigned int clock; /* clock rate */
unsigned int old_rate; /* saved clock rate */
unsigned long clk_ts; /* time stamp of last updated clock */
unsigned short vdd;
unsigned int power_delay_ms; /* waiting for stable power */
/* vdd stores the bit number of the selected voltage range from below. */
unsigned char bus_mode; /* command output mode */
#define MMC_BUSMODE_OPENDRAIN 1
#define MMC_BUSMODE_PUSHPULL 2
unsigned char chip_select; /* SPI chip select */
#define MMC_CS_DONTCARE 0
#define MMC_CS_HIGH 1
#define MMC_CS_LOW 2
unsigned char power_mode; /* power supply mode */
#define MMC_POWER_OFF 0
#define MMC_POWER_UP 1
#define MMC_POWER_ON 2
#define MMC_POWER_UNDEFINED 3
unsigned char bus_width; /* data bus width */
#define MMC_BUS_WIDTH_1 0
#define MMC_BUS_WIDTH_4 2
#define MMC_BUS_WIDTH_8 3
unsigned char timing; /* timing specification used */
#define MMC_TIMING_LEGACY 0
#define MMC_TIMING_MMC_HS 1
#define MMC_TIMING_SD_HS 2
#define MMC_TIMING_UHS_SDR12 3
#define MMC_TIMING_UHS_SDR25 4
#define MMC_TIMING_UHS_SDR50 5
#define MMC_TIMING_UHS_SDR104 6
#define MMC_TIMING_UHS_DDR50 7
#define MMC_TIMING_MMC_DDR52 8
#define MMC_TIMING_MMC_HS200 9
#define MMC_TIMING_MMC_HS400 10
unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
#define MMC_SIGNAL_VOLTAGE_330 0
#define MMC_SIGNAL_VOLTAGE_180 1
#define MMC_SIGNAL_VOLTAGE_120 2
unsigned char drv_type; /* driver type (A, B, C, D) */
#define MMC_SET_DRIVER_TYPE_B 0
#define MMC_SET_DRIVER_TYPE_A 1
#define MMC_SET_DRIVER_TYPE_C 2
#define MMC_SET_DRIVER_TYPE_D 3
bool enhanced_strobe; /* hs400es selection */
};
struct mmc_host;
enum {
MMC_ERR_CMD_TIMEOUT,
MMC_ERR_CMD_CRC,
MMC_ERR_DAT_TIMEOUT,
MMC_ERR_DAT_CRC,
MMC_ERR_AUTO_CMD,
MMC_ERR_ADMA,
MMC_ERR_TUNING,
MMC_ERR_CMDQ_RED,
MMC_ERR_CMDQ_GCE,
MMC_ERR_CMDQ_ICCE,
MMC_ERR_REQ_TIMEOUT,
MMC_ERR_CMDQ_REQ_TIMEOUT,
MMC_ERR_ICE_CFG,
MMC_ERR_MAX,
};
/* states to represent load on the host */
enum mmc_load {
MMC_LOAD_HIGH,
MMC_LOAD_LOW,
};
struct mmc_host_ops {
int (*init)(struct mmc_host *host);
/*
* 'enable' is called when the host is claimed and 'disable' is called
* when the host is released. 'enable' and 'disable' are deprecated.
*/
int (*enable)(struct mmc_host *host);
int (*disable)(struct mmc_host *host);
/*
* It is optional for the host to implement pre_req and post_req in
* order to support double buffering of requests (prepare one
* request while another request is active).
* pre_req() must always be followed by a post_req().
* To undo a call made to pre_req(), call post_req() with
* a nonzero err condition.
*/
void (*post_req)(struct mmc_host *host, struct mmc_request *req,
int err);
void (*pre_req)(struct mmc_host *host, struct mmc_request *req);
void (*request)(struct mmc_host *host, struct mmc_request *req);
/*
* Avoid calling the next three functions too often or in a "fast
* path", since underlaying controller might implement them in an
* expensive and/or slow way. Also note that these functions might
* sleep, so don't call them in the atomic contexts!
*/
/*
* Notes to the set_ios callback:
* ios->clock might be 0. For some controllers, setting 0Hz
* as any other frequency works. However, some controllers
* explicitly need to disable the clock. Otherwise e.g. voltage
* switching might fail because the SDCLK is not really quiet.
*/
void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);
/*
* Return values for the get_ro callback should be:
* 0 for a read/write card
* 1 for a read-only card
* -ENOSYS when not supported (equal to NULL callback)
* or a negative errno value when something bad happened
*/
int (*get_ro)(struct mmc_host *host);
/*
* Return values for the get_cd callback should be:
* 0 for a absent card
* 1 for a present card
* -ENOSYS when not supported (equal to NULL callback)
* or a negative errno value when something bad happened
*/
int (*get_cd)(struct mmc_host *host);
void (*enable_sdio_irq)(struct mmc_host *host, int enable);
void (*ack_sdio_irq)(struct mmc_host *host);
/* optional callback for HC quirks */
void (*init_card)(struct mmc_host *host, struct mmc_card *card);
int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
/* Check if the card is pulling dat[0:3] low */
int (*card_busy)(struct mmc_host *host);
/* The tuning command opcode value is different for SD and eMMC cards */
int (*execute_tuning)(struct mmc_host *host, u32 opcode);
/* Prepare HS400 target operating frequency depending host driver */
int (*prepare_hs400_tuning)(struct mmc_host *host, struct mmc_ios *ios);
int (*enhanced_strobe)(struct mmc_host *host);
/* Prepare for switching from HS400 to HS200 */
void (*hs400_downgrade)(struct mmc_host *host);
/* Complete selection of HS400 */
void (*hs400_complete)(struct mmc_host *host);
/* Prepare enhanced strobe depending host driver */
void (*hs400_enhanced_strobe)(struct mmc_host *host,
struct mmc_ios *ios);
int (*select_drive_strength)(struct mmc_card *card,
unsigned int max_dtr, int host_drv,
int card_drv, int *drv_type);
void (*hw_reset)(struct mmc_host *host);
void (*card_event)(struct mmc_host *host);
/*
* Optional callback to support controllers with HW issues for multiple
* I/O. Returns the number of supported blocks for the request.
*/
int (*multi_io_quirk)(struct mmc_card *card,
unsigned int direction, int blk_size);
unsigned long (*get_max_frequency)(struct mmc_host *host);
unsigned long (*get_min_frequency)(struct mmc_host *host);
int (*notify_load)(struct mmc_host *host, enum mmc_load);
void (*notify_halt)(struct mmc_host *mmc, bool halt);
void (*force_err_irq)(struct mmc_host *host, u64 errmask);
};
struct mmc_cqe_ops {
/* Allocate resources, and make the CQE operational */
int (*cqe_enable)(struct mmc_host *host, struct mmc_card *card);
/* Free resources, and make the CQE non-operational */
void (*cqe_disable)(struct mmc_host *host);
/*
* Issue a read, write or DCMD request to the CQE. Also deal with the
* effect of ->cqe_off().
*/
int (*cqe_request)(struct mmc_host *host, struct mmc_request *mrq);
/* Free resources (e.g. DMA mapping) associated with the request */
void (*cqe_post_req)(struct mmc_host *host, struct mmc_request *mrq);
/*
* Prepare the CQE and host controller to accept non-CQ commands. There
* is no corresponding ->cqe_on(), instead ->cqe_request() is required
* to deal with that.
*/
void (*cqe_off)(struct mmc_host *host);
/*
* Wait for all CQE tasks to complete. Return an error if recovery
* becomes necessary.
*/
int (*cqe_wait_for_idle)(struct mmc_host *host);
/*
* Notify CQE that a request has timed out. Return false if the request
* completed or true if a timeout happened in which case indicate if
* recovery is needed.
*/
bool (*cqe_timeout)(struct mmc_host *host, struct mmc_request *mrq,
bool *recovery_needed);
/*
* Stop all CQE activity and prepare the CQE and host controller to
* accept recovery commands.
*/
void (*cqe_recovery_start)(struct mmc_host *host);
/*
* Clear the queue and call mmc_cqe_request_done() on all requests.
* Requests that errored will have the error set on the mmc_request
* (data->error or cmd->error for DCMD). Requests that did not error
* will have zero data bytes transferred.
*/
void (*cqe_recovery_finish)(struct mmc_host *host);
};
struct mmc_async_req {
/* active mmc request */
struct mmc_request *mrq;
/*
* Check error status of completed mmc request.
* Returns 0 if success otherwise non zero.
*/
enum mmc_blk_status (*err_check)(struct mmc_card *, struct mmc_async_req *);
};
/**
* struct mmc_slot - MMC slot functions
*
* @cd_irq: MMC/SD-card slot hotplug detection IRQ or -EINVAL
* @handler_priv: MMC/SD-card slot context
*
* Some MMC/SD host controllers implement slot-functions like card and
* write-protect detection natively. However, a large number of controllers
* leave these functions to the CPU. This struct provides a hook to attach
* such slot-function drivers.
*/
struct mmc_slot {
int cd_irq;
bool cd_wake_enabled;
void *handler_priv;
};
/**
* mmc_context_info - synchronization details for mmc context
* @is_done_rcv wake up reason was done request
* @is_new_req wake up reason was new request
* @is_waiting_last_req mmc context waiting for single running request
* @wait wait queue
* @lock lock to protect data fields
*/
struct mmc_context_info {
bool is_done_rcv;
bool is_new_req;
bool is_waiting_last_req;
wait_queue_head_t wait;
spinlock_t lock;
};
struct regulator;
struct mmc_pwrseq;
struct mmc_supply {
struct regulator *vmmc; /* Card power supply */
struct regulator *vqmmc; /* Optional Vccq supply */
};
struct mmc_ctx {
struct task_struct *task;
};
enum dev_state {
DEV_SUSPENDING = 1,
DEV_SUSPENDED,
DEV_RESUMED,
};
/**
* struct mmc_devfeq_clk_scaling - main context for MMC clock scaling logic
*
* @lock: spinlock to protect statistics
* @devfreq: struct that represent mmc-host as a client for devfreq
* @devfreq_profile: MMC device profile, mostly polling interval and callbacks
* @ondemand_gov_data: struct supplied to ondemmand governor (thresholds)
* @state: load state, can be HIGH or LOW. used to notify mmc_host_ops callback
* @start_busy: timestamped armed once a data request is started
* @measure_interval_start: timestamped armed once a measure interval started
* @devfreq_abort: flag to sync between different contexts relevant to devfreq
* @skip_clk_scale_freq_update: flag that enable/disable frequency change
* @freq_table_sz: table size of frequencies supplied to devfreq
* @freq_table: frequencies table supplied to devfreq
* @curr_freq: current frequency
* @polling_delay_ms: polling interval for status collection used by devfreq
* @upthreshold: up-threshold supplied to ondemand governor
* @downthreshold: down-threshold supplied to ondemand governor
* @need_freq_change: flag indicating if a frequency change is required
* @is_busy_started: flag indicating if a request is handled by the HW
* @enable: flag indicating if the clock scaling logic is enabled for this host
* @is_suspended: to make devfreq request queued when mmc is suspened
*/
struct mmc_devfeq_clk_scaling {
spinlock_t lock;
struct devfreq *devfreq;
struct devfreq_dev_profile devfreq_profile;
struct devfreq_simple_ondemand_data ondemand_gov_data;
enum mmc_load state;
ktime_t start_busy;
ktime_t measure_interval_start;
atomic_t devfreq_abort;
bool skip_clk_scale_freq_update;
int freq_table_sz;
int pltfm_freq_table_sz;
u32 *freq_table;
u32 *pltfm_freq_table;
unsigned long total_busy_time_us;
unsigned long target_freq;
unsigned long curr_freq;
unsigned long polling_delay_ms;
unsigned int upthreshold;
unsigned int downthreshold;
unsigned int lower_bus_speed_mode;
#define MMC_SCALING_LOWER_DDR52_MODE 1
bool need_freq_change;
bool is_busy_started;
bool enable;
bool is_suspended;
};
struct mmc_host {
struct device *parent;
struct device class_dev;
struct mmc_devfeq_clk_scaling clk_scaling;
int index;
const struct mmc_host_ops *ops;
struct mmc_pwrseq *pwrseq;
unsigned int f_min;
unsigned int f_max;
unsigned int f_init;
u32 ocr_avail;
u32 ocr_avail_sdio; /* SDIO-specific OCR */
u32 ocr_avail_sd; /* SD-specific OCR */
u32 ocr_avail_mmc; /* MMC-specific OCR */
#ifdef CONFIG_PM_SLEEP
struct notifier_block pm_notify;
#endif
u32 max_current_330;
u32 max_current_300;
u32 max_current_180;
#define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
#define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
#define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
#define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
#define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
#define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
#define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
#define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
#define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
#define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
#define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
#define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
#define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
#define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
#define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
#define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
#define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
u32 caps; /* Host capabilities */
#define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
#define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */
#define MMC_CAP_AGGRESSIVE_PM (1 << 7) /* Suspend (e)MMC/SD at idle */
#define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */
#define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */
#define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */
#define MMC_CAP_3_3V_DDR (1 << 11) /* Host supports eMMC DDR 3.3V */
#define MMC_CAP_1_8V_DDR (1 << 12) /* Host supports eMMC DDR 1.8V */
#define MMC_CAP_1_2V_DDR (1 << 13) /* Host supports eMMC DDR 1.2V */
#define MMC_CAP_POWER_OFF_CARD (1 << 14) /* Can power off after boot */
#define MMC_CAP_BUS_WIDTH_TEST (1 << 15) /* CMD14/CMD19 bus width ok */
#define MMC_CAP_UHS_SDR12 (1 << 16) /* Host supports UHS SDR12 mode */
#define MMC_CAP_UHS_SDR25 (1 << 17) /* Host supports UHS SDR25 mode */
#define MMC_CAP_UHS_SDR50 (1 << 18) /* Host supports UHS SDR50 mode */
#define MMC_CAP_UHS_SDR104 (1 << 19) /* Host supports UHS SDR104 mode */
#define MMC_CAP_UHS_DDR50 (1 << 20) /* Host supports UHS DDR50 mode */
#define MMC_CAP_UHS (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | \
MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | \
MMC_CAP_UHS_DDR50)
/* (1 << 21) is free for reuse */
#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
#define MMC_CAP_DONE_COMPLETE (1 << 27) /* RW reqs can be completed within mmc_request_done() */
#define MMC_CAP_CD_WAKE (1 << 28) /* Enable card detect wake */
#define MMC_CAP_CMD_DURING_TFR (1 << 29) /* Commands during data transfer */
#define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */
#define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */
u32 caps2; /* More host capabilities */
#define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */
#define MMC_CAP2_FULL_PWR_CYCLE (1 << 2) /* Can do full power cycle */
#define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */
#define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */
#define MMC_CAP2_SLEEP_AWAKE (1 << 7) /* Use Sleep/Awake (CMD5) */
/* use max discard ignoring max_busy_timeout parameter */
#define MMC_CAP2_MAX_DISCARD_SIZE (1 << 8)
#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
MMC_CAP2_HS200_1_2V_SDR)
#define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */
#define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */
#define MMC_CAP2_PACKED_RD (1 << 12) /* Allow packed read */
#define MMC_CAP2_PACKED_WR (1 << 13) /* Allow packed write */
#define MMC_CAP2_PACKED_CMD (MMC_CAP2_PACKED_RD | \
MMC_CAP2_PACKED_WR)
#define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */
#define MMC_CAP2_HS400_1_8V (1 << 15) /* Can support HS400 1.8V */
#define MMC_CAP2_HS400_1_2V (1 << 16) /* Can support HS400 1.2V */
#define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \
MMC_CAP2_HS400_1_2V)
#define MMC_CAP2_HSX00_1_8V (MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)
#define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
#define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
#define MMC_CAP2_NO_WRITE_PROTECT (1 << 18) /* No physical write protect pin, assume that card is always read-write */
#define MMC_CAP2_NO_SDIO (1 << 19) /* Do not send SDIO commands during initialization */
#define MMC_CAP2_HS400_ES (1 << 20) /* Host supports enhanced strobe */
#define MMC_CAP2_NO_SD (1 << 21) /* Do not send SD commands during initialization */
#define MMC_CAP2_NO_MMC (1 << 22) /* Do not send (e)MMC commands during initialization */
#define MMC_CAP2_CQE (1 << 23) /* Has eMMC command queue engine */
#define MMC_CAP2_CQE_DCMD (1 << 24) /* CQE can issue a direct command */
#define MMC_CAP2_AVOID_3_3V (1 << 25) /* Host must negotiate down from 3.3V */
#define MMC_CAP2_PACKED_WR_CONTROL (1 << 26) /* Allow write packed control */
#define MMC_CAP2_CLK_SCALE (1 << 27) /* Allow dynamic clk scaling */
#define MMC_CAP2_ASYNC_SDIO_IRQ_4BIT_MODE (1 << 28) /* Allow Async SDIO irq */
/* while card in 4-bit mode */
#define MMC_CAP2_NONHOTPLUG (1 << 29) /*Don't support hotplug*/
/* Some hosts need additional tuning */
#define MMC_CAP2_HS400_POST_TUNING (1 << 30)
#define MMC_CAP2_SANITIZE (1 << 31) /* Support Sanitize */
int fixed_drv_type; /* fixed driver type for non-removable media */
mmc_pm_flag_t pm_caps; /* supported pm features */
#ifdef CONFIG_MMC_CLKGATE
int clk_requests; /* internal reference counter */
unsigned int clk_delay; /* number MCI clk hold cycles */
bool clk_gated; /* clock gated */
struct workqueue_struct *clk_gate_wq; /* clock gate work queue */
struct delayed_work clk_gate_work; /* delayed clock gate */
unsigned int clk_old; /* old clock value cache */
spinlock_t clk_lock; /* lock for clk fields */
struct mutex clk_gate_mutex; /* mutex for clock gating */
struct device_attribute clkgate_delay_attr;
unsigned long clkgate_delay;
#endif
/* host specific block data */
unsigned int max_seg_size; /* see blk_queue_max_segment_size */
unsigned short max_segs; /* see blk_queue_max_segments */
unsigned short unused;
unsigned int max_req_size; /* maximum number of bytes in one req */
unsigned int max_blk_size; /* maximum size of one mmc block */
unsigned int max_blk_count; /* maximum number of blocks in one req */
unsigned int max_busy_timeout; /* max busy timeout in ms */
/* private data */
spinlock_t lock; /* lock for claim and bus ops */
struct mmc_ios ios; /* current io bus settings */
struct mmc_ios cached_ios;
/* group bitfields together to minimize padding */
unsigned int use_spi_crc:1;
unsigned int claimed:1; /* host exclusively claimed */
unsigned int bus_dead:1; /* bus has been released */
unsigned int can_retune:1; /* re-tuning can be used */
unsigned int doing_retune:1; /* re-tuning in progress */
unsigned int retune_now:1; /* do re-tuning at next req */
unsigned int retune_paused:1; /* re-tuning is temporarily disabled */
unsigned int use_blk_mq:1; /* use blk-mq */
int rescan_disable; /* disable card detection */
int rescan_entered; /* used with nonremovable devices */
int need_retune; /* re-tuning is needed */
int hold_retune; /* hold off re-tuning */
unsigned int retune_period; /* re-tuning period in secs */
struct timer_list retune_timer; /* for periodic re-tuning */
bool trigger_card_event; /* card_event necessary */
struct mmc_card *card; /* device attached to this host */
wait_queue_head_t wq;
struct mmc_ctx *claimer; /* context that has host claimed */
int claim_cnt; /* "claim" nesting count */
struct mmc_ctx default_ctx; /* default context */
struct delayed_work detect;
int detect_change; /* card detect flag */
struct mmc_slot slot;
const struct mmc_bus_ops *bus_ops; /* current bus driver */
unsigned int bus_refs; /* reference counter */
unsigned int bus_resume_flags;
#define MMC_BUSRESUME_MANUAL_RESUME (1 << 0)
#define MMC_BUSRESUME_NEEDS_RESUME (1 << 1)
bool ignore_bus_resume_flags;
unsigned int sdio_irqs;
struct task_struct *sdio_irq_thread;
struct delayed_work sdio_irq_work;
bool sdio_irq_pending;
atomic_t sdio_irq_thread_abort;
mmc_pm_flag_t pm_flags; /* requested pm features */
struct led_trigger *led; /* activity led */
#ifdef CONFIG_REGULATOR
bool regulator_enabled; /* regulator state */
#endif
struct mmc_supply supply;
struct dentry *debugfs_root;
bool err_occurred;
u32 err_stats[MMC_ERR_MAX];
/* Ongoing data transfer that allows commands during transfer */
struct mmc_request *ongoing_mrq;
#ifdef CONFIG_FAIL_MMC_REQUEST
struct fault_attr fail_mmc_request;
#endif
unsigned int actual_clock; /* Actual HC clock rate */
unsigned int slotno; /* used for sdio acpi binding */
int dsr_req; /* DSR value is valid */
u32 dsr; /* optional driver stage (DSR) value */
/* Command Queue Engine (CQE) support */
const struct mmc_cqe_ops *cqe_ops;
void *cqe_private;
int cqe_qdepth;
bool cqe_enabled;
bool cqe_on;
/*
* Set to 1 to just stop the SDCLK to the card without
* actually disabling the clock from it's source.
*/
bool card_clock_off;
struct extcon_dev *extcon;
struct notifier_block card_detect_nb;
#ifdef CONFIG_MMC_PERF_PROFILING
struct {
unsigned long rbytes_drv; /* Rd bytes MMC Host */
unsigned long wbytes_drv; /* Wr bytes MMC Host */
ktime_t rtime_drv; /* Rd time MMC Host */
ktime_t wtime_drv; /* Wr time MMC Host */
ktime_t start;
} perf;
bool perf_enable;
#endif
#ifdef CONFIG_MMC_IPC_LOGGING
void *ipc_log_ctxt;
bool stop_tracing;
#endif
enum dev_state dev_status;
bool inlinecrypt_support; /* Inline encryption support */
bool inlinecrypt_reset_needed; /* Inline crypto reset */
bool crash_on_err; /* crash the system on error */
atomic_t active_reqs;
unsigned long private[0] ____cacheline_aligned;
};
struct device_node;
struct mmc_host *mmc_alloc_host(int extra, struct device *);
extern bool mmc_host_may_gate_card(struct mmc_card *card);
int mmc_add_host(struct mmc_host *);
void mmc_remove_host(struct mmc_host *);
void mmc_free_host(struct mmc_host *);
int mmc_of_parse(struct mmc_host *host);
int mmc_of_parse_voltage(struct device_node *np, u32 *mask);
#ifdef CONFIG_MMC_IPC_LOGGING
#define NUM_LOG_PAGES 10
#define mmc_log_string(mmc_host, fmt, ...) do { \
if ((mmc_host)->ipc_log_ctxt && !(mmc_host)->stop_tracing) \
ipc_log_string((mmc_host)->ipc_log_ctxt, \
"%s: " fmt, __func__, ##__VA_ARGS__); \
} while (0)
#else
#define mmc_log_string(mmc_host, fmt, ...) do { } while (0)
#endif
static inline void *mmc_priv(struct mmc_host *host)
{
return (void *)host->private;
}
#define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI)
#define mmc_dev(x) ((x)->parent)
#define mmc_classdev(x) (&(x)->class_dev)
#define mmc_hostname(x) (dev_name(&(x)->class_dev))
#define mmc_bus_needs_resume(host) ((host)->bus_resume_flags & \
MMC_BUSRESUME_NEEDS_RESUME)
#define mmc_bus_manual_resume(host) ((host)->bus_resume_flags & \
MMC_BUSRESUME_MANUAL_RESUME)
#ifdef CONFIG_MMC_BLOCK_DEFERRED_RESUME
static inline void mmc_set_bus_resume_policy(struct mmc_host *host, int manual)
{
if (manual)
host->bus_resume_flags |= MMC_BUSRESUME_MANUAL_RESUME;
else
host->bus_resume_flags &= ~MMC_BUSRESUME_MANUAL_RESUME;
}
#else
static inline void mmc_set_bus_resume_policy(struct mmc_host *host, int manual)
{
}
#endif
extern int mmc_resume_bus(struct mmc_host *host);
void mmc_detect_change(struct mmc_host *, unsigned long delay);
void mmc_request_done(struct mmc_host *, struct mmc_request *);
void mmc_command_done(struct mmc_host *host, struct mmc_request *mrq);
void mmc_cqe_request_done(struct mmc_host *host, struct mmc_request *mrq);
static inline void mmc_signal_sdio_irq(struct mmc_host *host)
{
host->ops->enable_sdio_irq(host, 0);
host->sdio_irq_pending = true;
if (host->sdio_irq_thread)
wake_up_process(host->sdio_irq_thread);
}
void sdio_run_irqs(struct mmc_host *host);
void sdio_signal_irq(struct mmc_host *host);
#ifdef CONFIG_REGULATOR
int mmc_regulator_get_ocrmask(struct regulator *supply);
int mmc_regulator_set_ocr(struct mmc_host *mmc,
struct regulator *supply,
unsigned short vdd_bit);
int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios);
#else
static inline int mmc_regulator_get_ocrmask(struct regulator *supply)
{
return 0;
}
static inline int mmc_regulator_set_ocr(struct mmc_host *mmc,
struct regulator *supply,
unsigned short vdd_bit)
{
return 0;
}
static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc,
struct mmc_ios *ios)
{
return -EINVAL;
}
#endif
u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max);
int mmc_regulator_get_supply(struct mmc_host *mmc);
static inline int mmc_card_is_removable(struct mmc_host *host)
{
return !(host->caps & MMC_CAP_NONREMOVABLE);
}
static inline int mmc_card_keep_power(struct mmc_host *host)
{
return host->pm_flags & MMC_PM_KEEP_POWER;
}
static inline int mmc_card_wake_sdio_irq(struct mmc_host *host)
{
return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ;
}
static inline bool mmc_card_and_host_support_async_int(struct mmc_host *host)
{
return ((host->caps2 & MMC_CAP2_ASYNC_SDIO_IRQ_4BIT_MODE) &&
(host->card->cccr.async_intr_sup));
}
static inline void mmc_host_clear_sdr104(struct mmc_host *host)
{
host->caps &= ~MMC_CAP_UHS_SDR104;
}
static inline void mmc_host_set_sdr104(struct mmc_host *host)
{
host->caps |= MMC_CAP_UHS_SDR104;
}
#ifdef CONFIG_MMC_CLKGATE
void mmc_host_clk_hold(struct mmc_host *host);
void mmc_host_clk_release(struct mmc_host *host);
unsigned int mmc_host_clk_rate(struct mmc_host *host);
#else
static inline void mmc_host_clk_hold(struct mmc_host *host)
{
}
static inline void mmc_host_clk_release(struct mmc_host *host)
{
}
static inline unsigned int mmc_host_clk_rate(struct mmc_host *host)
{
return host->ios.clock;
}
#endif
static inline int mmc_card_hs(struct mmc_card *card)
{
return card->host->ios.timing == MMC_TIMING_SD_HS ||
card->host->ios.timing == MMC_TIMING_MMC_HS;
}
/* TODO: Move to private header */
static inline int mmc_card_uhs(struct mmc_card *card)
{
return card->host->ios.timing >= MMC_TIMING_UHS_SDR12 &&
card->host->ios.timing <= MMC_TIMING_UHS_DDR50;
}
void mmc_retune_enable(struct mmc_host *host);
void mmc_retune_disable(struct mmc_host *host);
void mmc_retune_timer_stop(struct mmc_host *host);
static inline void mmc_retune_needed(struct mmc_host *host)
{
if (host->can_retune)
host->need_retune = 1;
}
static inline bool mmc_can_retune(struct mmc_host *host)
{
return host->can_retune == 1;
}
static inline enum dma_data_direction mmc_get_dma_dir(struct mmc_data *data)
{
return data->flags & MMC_DATA_WRITE ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
}
int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
int mmc_abort_tuning(struct mmc_host *host, u32 opcode);
#endif /* LINUX_MMC_HOST_H */
Reference in a new issue View git blame Copy permalink