android_kernel_samsung_hero.../arch/powerpc/kernel/exceptions-64s.S

1694 lines
45 KiB
ArmAsm
Raw Permalink Normal View History

2016-08-17 10:41:52 +02:00
/*
* This file contains the 64-bit "server" PowerPC variant
* of the low level exception handling including exception
* vectors, exception return, part of the slb and stab
* handling and other fixed offset specific things.
*
* This file is meant to be #included from head_64.S due to
* position dependent assembly.
*
* Most of this originates from head_64.S and thus has the same
* copyright history.
*
*/
#include <asm/hw_irq.h>
#include <asm/exception-64s.h>
#include <asm/ptrace.h>
/*
* We layout physical memory as follows:
* 0x0000 - 0x00ff : Secondary processor spin code
* 0x0100 - 0x17ff : pSeries Interrupt prologs
* 0x1800 - 0x4000 : interrupt support common interrupt prologs
* 0x4000 - 0x5fff : pSeries interrupts with IR=1,DR=1
* 0x6000 - 0x6fff : more interrupt support including for IR=1,DR=1
* 0x7000 - 0x7fff : FWNMI data area
* 0x8000 - 0x8fff : Initial (CPU0) segment table
* 0x9000 - : Early init and support code
*/
/* Syscall routine is used twice, in reloc-off and reloc-on paths */
#define SYSCALL_PSERIES_1 \
BEGIN_FTR_SECTION \
cmpdi r0,0x1ebe ; \
beq- 1f ; \
END_FTR_SECTION_IFSET(CPU_FTR_REAL_LE) \
mr r9,r13 ; \
GET_PACA(r13) ; \
mfspr r11,SPRN_SRR0 ; \
0:
#define SYSCALL_PSERIES_2_RFID \
mfspr r12,SPRN_SRR1 ; \
ld r10,PACAKBASE(r13) ; \
LOAD_HANDLER(r10, system_call_entry) ; \
mtspr SPRN_SRR0,r10 ; \
ld r10,PACAKMSR(r13) ; \
mtspr SPRN_SRR1,r10 ; \
rfid ; \
b . ; /* prevent speculative execution */
#define SYSCALL_PSERIES_3 \
/* Fast LE/BE switch system call */ \
1: mfspr r12,SPRN_SRR1 ; \
xori r12,r12,MSR_LE ; \
mtspr SPRN_SRR1,r12 ; \
rfid ; /* return to userspace */ \
b . ; /* prevent speculative execution */
#if defined(CONFIG_RELOCATABLE)
/*
* We can't branch directly; in the direct case we use LR
* and system_call_entry restores LR. (We thus need to move
* LR to r10 in the RFID case too.)
*/
#define SYSCALL_PSERIES_2_DIRECT \
mflr r10 ; \
ld r12,PACAKBASE(r13) ; \
LOAD_HANDLER(r12, system_call_entry_direct) ; \
mtctr r12 ; \
mfspr r12,SPRN_SRR1 ; \
/* Re-use of r13... No spare regs to do this */ \
li r13,MSR_RI ; \
mtmsrd r13,1 ; \
GET_PACA(r13) ; /* get r13 back */ \
bctr ;
#else
/* We can branch directly */
#define SYSCALL_PSERIES_2_DIRECT \
mfspr r12,SPRN_SRR1 ; \
li r10,MSR_RI ; \
mtmsrd r10,1 ; /* Set RI (EE=0) */ \
b system_call_entry_direct ;
#endif
/*
* This is the start of the interrupt handlers for pSeries
* This code runs with relocation off.
* Code from here to __end_interrupts gets copied down to real
* address 0x100 when we are running a relocatable kernel.
* Therefore any relative branches in this section must only
* branch to labels in this section.
*/
. = 0x100
.globl __start_interrupts
__start_interrupts:
.globl system_reset_pSeries;
system_reset_pSeries:
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13)
#ifdef CONFIG_PPC_P7_NAP
BEGIN_FTR_SECTION
/* Running native on arch 2.06 or later, check if we are
* waking up from nap. We only handle no state loss and
* supervisor state loss. We do -not- handle hypervisor
* state loss at this time.
*/
mfspr r13,SPRN_SRR1
rlwinm. r13,r13,47-31,30,31
beq 9f
/* waking up from powersave (nap) state */
cmpwi cr1,r13,2
/* Total loss of HV state is fatal, we could try to use the
* PIR to locate a PACA, then use an emergency stack etc...
* OPAL v3 based powernv platforms have new idle states
* which fall in this catagory.
*/
bgt cr1,8f
GET_PACA(r13)
#ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
li r0,KVM_HWTHREAD_IN_KERNEL
stb r0,HSTATE_HWTHREAD_STATE(r13)
/* Order setting hwthread_state vs. testing hwthread_req */
sync
lbz r0,HSTATE_HWTHREAD_REQ(r13)
cmpwi r0,0
beq 1f
b kvm_start_guest
1:
#endif
beq cr1,2f
b power7_wakeup_noloss
2: b power7_wakeup_loss
/* Fast Sleep wakeup on PowerNV */
8: GET_PACA(r13)
b power7_wakeup_tb_loss
9:
END_FTR_SECTION_IFSET(CPU_FTR_HVMODE | CPU_FTR_ARCH_206)
#endif /* CONFIG_PPC_P7_NAP */
EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, system_reset_common, EXC_STD,
NOTEST, 0x100)
. = 0x200
machine_check_pSeries_1:
/* This is moved out of line as it can be patched by FW, but
* some code path might still want to branch into the original
* vector
*/
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13) /* save r13 */
#ifdef CONFIG_PPC_P7_NAP
BEGIN_FTR_SECTION
/* Running native on arch 2.06 or later, check if we are
* waking up from nap. We only handle no state loss and
* supervisor state loss. We do -not- handle hypervisor
* state loss at this time.
*/
mfspr r13,SPRN_SRR1
rlwinm. r13,r13,47-31,30,31
OPT_GET_SPR(r13, SPRN_CFAR, CPU_FTR_CFAR)
beq 9f
mfspr r13,SPRN_SRR1
rlwinm. r13,r13,47-31,30,31
/* waking up from powersave (nap) state */
cmpwi cr1,r13,2
/* Total loss of HV state is fatal. let's just stay stuck here */
OPT_GET_SPR(r13, SPRN_CFAR, CPU_FTR_CFAR)
bgt cr1,.
9:
OPT_SET_SPR(r13, SPRN_CFAR, CPU_FTR_CFAR)
END_FTR_SECTION_IFSET(CPU_FTR_HVMODE | CPU_FTR_ARCH_206)
#endif /* CONFIG_PPC_P7_NAP */
EXCEPTION_PROLOG_0(PACA_EXMC)
BEGIN_FTR_SECTION
b machine_check_pSeries_early
FTR_SECTION_ELSE
b machine_check_pSeries_0
ALT_FTR_SECTION_END_IFSET(CPU_FTR_HVMODE)
. = 0x300
.globl data_access_pSeries
data_access_pSeries:
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, data_access_common, EXC_STD,
KVMTEST, 0x300)
. = 0x380
.globl data_access_slb_pSeries
data_access_slb_pSeries:
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXSLB)
EXCEPTION_PROLOG_1(PACA_EXSLB, KVMTEST, 0x380)
std r3,PACA_EXSLB+EX_R3(r13)
mfspr r3,SPRN_DAR
#ifdef __DISABLED__
/* Keep that around for when we re-implement dynamic VSIDs */
cmpdi r3,0
bge slb_miss_user_pseries
#endif /* __DISABLED__ */
mfspr r12,SPRN_SRR1
#ifndef CONFIG_RELOCATABLE
b slb_miss_realmode
#else
/*
* We can't just use a direct branch to slb_miss_realmode
* because the distance from here to there depends on where
* the kernel ends up being put.
*/
mfctr r11
ld r10,PACAKBASE(r13)
LOAD_HANDLER(r10, slb_miss_realmode)
mtctr r10
bctr
#endif
STD_EXCEPTION_PSERIES(0x400, 0x400, instruction_access)
. = 0x480
.globl instruction_access_slb_pSeries
instruction_access_slb_pSeries:
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXSLB)
EXCEPTION_PROLOG_1(PACA_EXSLB, KVMTEST_PR, 0x480)
std r3,PACA_EXSLB+EX_R3(r13)
mfspr r3,SPRN_SRR0 /* SRR0 is faulting address */
#ifdef __DISABLED__
/* Keep that around for when we re-implement dynamic VSIDs */
cmpdi r3,0
bge slb_miss_user_pseries
#endif /* __DISABLED__ */
mfspr r12,SPRN_SRR1
#ifndef CONFIG_RELOCATABLE
b slb_miss_realmode
#else
mfctr r11
ld r10,PACAKBASE(r13)
LOAD_HANDLER(r10, slb_miss_realmode)
mtctr r10
bctr
#endif
/* We open code these as we can't have a ". = x" (even with
* x = "." within a feature section
*/
. = 0x500;
.globl hardware_interrupt_pSeries;
.globl hardware_interrupt_hv;
hardware_interrupt_pSeries:
hardware_interrupt_hv:
HMT_MEDIUM_PPR_DISCARD
BEGIN_FTR_SECTION
_MASKABLE_EXCEPTION_PSERIES(0x502, hardware_interrupt,
EXC_HV, SOFTEN_TEST_HV)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0x502)
FTR_SECTION_ELSE
_MASKABLE_EXCEPTION_PSERIES(0x500, hardware_interrupt,
EXC_STD, SOFTEN_TEST_HV_201)
KVM_HANDLER(PACA_EXGEN, EXC_STD, 0x500)
ALT_FTR_SECTION_END_IFSET(CPU_FTR_HVMODE | CPU_FTR_ARCH_206)
STD_EXCEPTION_PSERIES(0x600, 0x600, alignment)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x600)
STD_EXCEPTION_PSERIES(0x700, 0x700, program_check)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x700)
STD_EXCEPTION_PSERIES(0x800, 0x800, fp_unavailable)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x800)
. = 0x900
.globl decrementer_pSeries
decrementer_pSeries:
_MASKABLE_EXCEPTION_PSERIES(0x900, decrementer, EXC_STD, SOFTEN_TEST_PR)
STD_EXCEPTION_HV(0x980, 0x982, hdecrementer)
MASKABLE_EXCEPTION_PSERIES(0xa00, 0xa00, doorbell_super)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xa00)
STD_EXCEPTION_PSERIES(0xb00, 0xb00, trap_0b)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xb00)
. = 0xc00
.globl system_call_pSeries
system_call_pSeries:
HMT_MEDIUM
#ifdef CONFIG_KVM_BOOK3S_64_HANDLER
SET_SCRATCH0(r13)
GET_PACA(r13)
std r9,PACA_EXGEN+EX_R9(r13)
std r10,PACA_EXGEN+EX_R10(r13)
mfcr r9
KVMTEST(0xc00)
GET_SCRATCH0(r13)
#endif
SYSCALL_PSERIES_1
SYSCALL_PSERIES_2_RFID
SYSCALL_PSERIES_3
KVM_HANDLER(PACA_EXGEN, EXC_STD, 0xc00)
STD_EXCEPTION_PSERIES(0xd00, 0xd00, single_step)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xd00)
/* At 0xe??? we have a bunch of hypervisor exceptions, we branch
* out of line to handle them
*/
. = 0xe00
hv_data_storage_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b h_data_storage_hv
. = 0xe20
hv_instr_storage_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b h_instr_storage_hv
. = 0xe40
emulation_assist_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b emulation_assist_hv
. = 0xe60
hv_exception_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b hmi_exception_early
. = 0xe80
hv_doorbell_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b h_doorbell_hv
/* We need to deal with the Altivec unavailable exception
* here which is at 0xf20, thus in the middle of the
* prolog code of the PerformanceMonitor one. A little
* trickery is thus necessary
*/
. = 0xf00
performance_monitor_pseries_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b performance_monitor_pSeries
. = 0xf20
altivec_unavailable_pseries_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b altivec_unavailable_pSeries
. = 0xf40
vsx_unavailable_pseries_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b vsx_unavailable_pSeries
. = 0xf60
facility_unavailable_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b facility_unavailable_pSeries
. = 0xf80
hv_facility_unavailable_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b facility_unavailable_hv
#ifdef CONFIG_CBE_RAS
STD_EXCEPTION_HV(0x1200, 0x1202, cbe_system_error)
KVM_HANDLER_SKIP(PACA_EXGEN, EXC_HV, 0x1202)
#endif /* CONFIG_CBE_RAS */
STD_EXCEPTION_PSERIES(0x1300, 0x1300, instruction_breakpoint)
KVM_HANDLER_PR_SKIP(PACA_EXGEN, EXC_STD, 0x1300)
. = 0x1500
.global denorm_exception_hv
denorm_exception_hv:
HMT_MEDIUM_PPR_DISCARD
mtspr SPRN_SPRG_HSCRATCH0,r13
EXCEPTION_PROLOG_0(PACA_EXGEN)
EXCEPTION_PROLOG_1(PACA_EXGEN, NOTEST, 0x1500)
#ifdef CONFIG_PPC_DENORMALISATION
mfspr r10,SPRN_HSRR1
mfspr r11,SPRN_HSRR0 /* save HSRR0 */
andis. r10,r10,(HSRR1_DENORM)@h /* denorm? */
addi r11,r11,-4 /* HSRR0 is next instruction */
bne+ denorm_assist
#endif
KVMTEST(0x1500)
EXCEPTION_PROLOG_PSERIES_1(denorm_common, EXC_HV)
KVM_HANDLER_SKIP(PACA_EXGEN, EXC_STD, 0x1500)
#ifdef CONFIG_CBE_RAS
STD_EXCEPTION_HV(0x1600, 0x1602, cbe_maintenance)
KVM_HANDLER_SKIP(PACA_EXGEN, EXC_HV, 0x1602)
#endif /* CONFIG_CBE_RAS */
STD_EXCEPTION_PSERIES(0x1700, 0x1700, altivec_assist)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x1700)
#ifdef CONFIG_CBE_RAS
STD_EXCEPTION_HV(0x1800, 0x1802, cbe_thermal)
KVM_HANDLER_SKIP(PACA_EXGEN, EXC_HV, 0x1802)
#else
. = 0x1800
#endif /* CONFIG_CBE_RAS */
/*** Out of line interrupts support ***/
.align 7
/* moved from 0x200 */
machine_check_pSeries_early:
BEGIN_FTR_SECTION
EXCEPTION_PROLOG_1(PACA_EXMC, NOTEST, 0x200)
/*
* Register contents:
* R13 = PACA
* R9 = CR
* Original R9 to R13 is saved on PACA_EXMC
*
* Switch to mc_emergency stack and handle re-entrancy (we limit
* the nested MCE upto level 4 to avoid stack overflow).
* Save MCE registers srr1, srr0, dar and dsisr and then set ME=1
*
* We use paca->in_mce to check whether this is the first entry or
* nested machine check. We increment paca->in_mce to track nested
* machine checks.
*
* If this is the first entry then set stack pointer to
* paca->mc_emergency_sp, otherwise r1 is already pointing to
* stack frame on mc_emergency stack.
*
* NOTE: We are here with MSR_ME=0 (off), which means we risk a
* checkstop if we get another machine check exception before we do
* rfid with MSR_ME=1.
*/
mr r11,r1 /* Save r1 */
lhz r10,PACA_IN_MCE(r13)
cmpwi r10,0 /* Are we in nested machine check */
bne 0f /* Yes, we are. */
/* First machine check entry */
ld r1,PACAMCEMERGSP(r13) /* Use MC emergency stack */
0: subi r1,r1,INT_FRAME_SIZE /* alloc stack frame */
addi r10,r10,1 /* increment paca->in_mce */
sth r10,PACA_IN_MCE(r13)
/* Limit nested MCE to level 4 to avoid stack overflow */
cmpwi r10,4
bgt 2f /* Check if we hit limit of 4 */
std r11,GPR1(r1) /* Save r1 on the stack. */
std r11,0(r1) /* make stack chain pointer */
mfspr r11,SPRN_SRR0 /* Save SRR0 */
std r11,_NIP(r1)
mfspr r11,SPRN_SRR1 /* Save SRR1 */
std r11,_MSR(r1)
mfspr r11,SPRN_DAR /* Save DAR */
std r11,_DAR(r1)
mfspr r11,SPRN_DSISR /* Save DSISR */
std r11,_DSISR(r1)
std r9,_CCR(r1) /* Save CR in stackframe */
/* Save r9 through r13 from EXMC save area to stack frame. */
EXCEPTION_PROLOG_COMMON_2(PACA_EXMC)
mfmsr r11 /* get MSR value */
ori r11,r11,MSR_ME /* turn on ME bit */
ori r11,r11,MSR_RI /* turn on RI bit */
ld r12,PACAKBASE(r13) /* get high part of &label */
LOAD_HANDLER(r12, machine_check_handle_early)
1: mtspr SPRN_SRR0,r12
mtspr SPRN_SRR1,r11
rfid
b . /* prevent speculative execution */
2:
/* Stack overflow. Stay on emergency stack and panic.
* Keep the ME bit off while panic-ing, so that if we hit
* another machine check we checkstop.
*/
addi r1,r1,INT_FRAME_SIZE /* go back to previous stack frame */
ld r11,PACAKMSR(r13)
ld r12,PACAKBASE(r13)
LOAD_HANDLER(r12, unrecover_mce)
li r10,MSR_ME
andc r11,r11,r10 /* Turn off MSR_ME */
b 1b
b . /* prevent speculative execution */
END_FTR_SECTION_IFSET(CPU_FTR_HVMODE)
machine_check_pSeries:
.globl machine_check_fwnmi
machine_check_fwnmi:
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13) /* save r13 */
EXCEPTION_PROLOG_0(PACA_EXMC)
machine_check_pSeries_0:
EXCEPTION_PROLOG_1(PACA_EXMC, KVMTEST, 0x200)
EXCEPTION_PROLOG_PSERIES_1(machine_check_common, EXC_STD)
KVM_HANDLER_SKIP(PACA_EXMC, EXC_STD, 0x200)
KVM_HANDLER_SKIP(PACA_EXGEN, EXC_STD, 0x300)
KVM_HANDLER_SKIP(PACA_EXSLB, EXC_STD, 0x380)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x400)
KVM_HANDLER_PR(PACA_EXSLB, EXC_STD, 0x480)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x900)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0x982)
#ifdef CONFIG_PPC_DENORMALISATION
denorm_assist:
BEGIN_FTR_SECTION
/*
* To denormalise we need to move a copy of the register to itself.
* For POWER6 do that here for all FP regs.
*/
mfmsr r10
ori r10,r10,(MSR_FP|MSR_FE0|MSR_FE1)
xori r10,r10,(MSR_FE0|MSR_FE1)
mtmsrd r10
sync
#define FMR2(n) fmr (n), (n) ; fmr n+1, n+1
#define FMR4(n) FMR2(n) ; FMR2(n+2)
#define FMR8(n) FMR4(n) ; FMR4(n+4)
#define FMR16(n) FMR8(n) ; FMR8(n+8)
#define FMR32(n) FMR16(n) ; FMR16(n+16)
FMR32(0)
FTR_SECTION_ELSE
/*
* To denormalise we need to move a copy of the register to itself.
* For POWER7 do that here for the first 32 VSX registers only.
*/
mfmsr r10
oris r10,r10,MSR_VSX@h
mtmsrd r10
sync
#define XVCPSGNDP2(n) XVCPSGNDP(n,n,n) ; XVCPSGNDP(n+1,n+1,n+1)
#define XVCPSGNDP4(n) XVCPSGNDP2(n) ; XVCPSGNDP2(n+2)
#define XVCPSGNDP8(n) XVCPSGNDP4(n) ; XVCPSGNDP4(n+4)
#define XVCPSGNDP16(n) XVCPSGNDP8(n) ; XVCPSGNDP8(n+8)
#define XVCPSGNDP32(n) XVCPSGNDP16(n) ; XVCPSGNDP16(n+16)
XVCPSGNDP32(0)
ALT_FTR_SECTION_END_IFCLR(CPU_FTR_ARCH_206)
BEGIN_FTR_SECTION
b denorm_done
END_FTR_SECTION_IFCLR(CPU_FTR_ARCH_207S)
/*
* To denormalise we need to move a copy of the register to itself.
* For POWER8 we need to do that for all 64 VSX registers
*/
XVCPSGNDP32(32)
denorm_done:
mtspr SPRN_HSRR0,r11
mtcrf 0x80,r9
ld r9,PACA_EXGEN+EX_R9(r13)
RESTORE_PPR_PACA(PACA_EXGEN, r10)
BEGIN_FTR_SECTION
ld r10,PACA_EXGEN+EX_CFAR(r13)
mtspr SPRN_CFAR,r10
END_FTR_SECTION_IFSET(CPU_FTR_CFAR)
ld r10,PACA_EXGEN+EX_R10(r13)
ld r11,PACA_EXGEN+EX_R11(r13)
ld r12,PACA_EXGEN+EX_R12(r13)
ld r13,PACA_EXGEN+EX_R13(r13)
HRFID
b .
#endif
.align 7
/* moved from 0xe00 */
STD_EXCEPTION_HV_OOL(0xe02, h_data_storage)
KVM_HANDLER_SKIP(PACA_EXGEN, EXC_HV, 0xe02)
STD_EXCEPTION_HV_OOL(0xe22, h_instr_storage)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0xe22)
STD_EXCEPTION_HV_OOL(0xe42, emulation_assist)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0xe42)
MASKABLE_EXCEPTION_HV_OOL(0xe62, hmi_exception)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0xe62)
MASKABLE_EXCEPTION_HV_OOL(0xe82, h_doorbell)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0xe82)
/* moved from 0xf00 */
STD_EXCEPTION_PSERIES_OOL(0xf00, performance_monitor)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xf00)
STD_EXCEPTION_PSERIES_OOL(0xf20, altivec_unavailable)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xf20)
STD_EXCEPTION_PSERIES_OOL(0xf40, vsx_unavailable)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xf40)
STD_EXCEPTION_PSERIES_OOL(0xf60, facility_unavailable)
KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xf60)
STD_EXCEPTION_HV_OOL(0xf82, facility_unavailable)
KVM_HANDLER(PACA_EXGEN, EXC_HV, 0xf82)
/*
* An interrupt came in while soft-disabled. We set paca->irq_happened, then:
* - If it was a decrementer interrupt, we bump the dec to max and and return.
* - If it was a doorbell we return immediately since doorbells are edge
* triggered and won't automatically refire.
* - If it was a HMI we return immediately since we handled it in realmode
* and it won't refire.
* - else we hard disable and return.
* This is called with r10 containing the value to OR to the paca field.
*/
#define MASKED_INTERRUPT(_H) \
masked_##_H##interrupt: \
std r11,PACA_EXGEN+EX_R11(r13); \
lbz r11,PACAIRQHAPPENED(r13); \
or r11,r11,r10; \
stb r11,PACAIRQHAPPENED(r13); \
cmpwi r10,PACA_IRQ_DEC; \
bne 1f; \
lis r10,0x7fff; \
ori r10,r10,0xffff; \
mtspr SPRN_DEC,r10; \
b 2f; \
1: cmpwi r10,PACA_IRQ_DBELL; \
beq 2f; \
cmpwi r10,PACA_IRQ_HMI; \
beq 2f; \
mfspr r10,SPRN_##_H##SRR1; \
rldicl r10,r10,48,1; /* clear MSR_EE */ \
rotldi r10,r10,16; \
mtspr SPRN_##_H##SRR1,r10; \
2: mtcrf 0x80,r9; \
ld r9,PACA_EXGEN+EX_R9(r13); \
ld r10,PACA_EXGEN+EX_R10(r13); \
ld r11,PACA_EXGEN+EX_R11(r13); \
GET_SCRATCH0(r13); \
##_H##rfid; \
b .
MASKED_INTERRUPT()
MASKED_INTERRUPT(H)
/*
* Called from arch_local_irq_enable when an interrupt needs
* to be resent. r3 contains 0x500, 0x900, 0xa00 or 0xe80 to indicate
* which kind of interrupt. MSR:EE is already off. We generate a
* stackframe like if a real interrupt had happened.
*
* Note: While MSR:EE is off, we need to make sure that _MSR
* in the generated frame has EE set to 1 or the exception
* handler will not properly re-enable them.
*/
_GLOBAL(__replay_interrupt)
/* We are going to jump to the exception common code which
* will retrieve various register values from the PACA which
* we don't give a damn about, so we don't bother storing them.
*/
mfmsr r12
mflr r11
mfcr r9
ori r12,r12,MSR_EE
cmpwi r3,0x900
beq decrementer_common
cmpwi r3,0x500
beq hardware_interrupt_common
BEGIN_FTR_SECTION
cmpwi r3,0xe80
beq h_doorbell_common
FTR_SECTION_ELSE
cmpwi r3,0xa00
beq doorbell_super_common
ALT_FTR_SECTION_END_IFSET(CPU_FTR_HVMODE)
blr
#ifdef CONFIG_PPC_PSERIES
/*
* Vectors for the FWNMI option. Share common code.
*/
.globl system_reset_fwnmi
.align 7
system_reset_fwnmi:
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13) /* save r13 */
EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, system_reset_common, EXC_STD,
NOTEST, 0x100)
#endif /* CONFIG_PPC_PSERIES */
#ifdef __DISABLED__
/*
* This is used for when the SLB miss handler has to go virtual,
* which doesn't happen for now anymore but will once we re-implement
* dynamic VSIDs for shared page tables
*/
slb_miss_user_pseries:
std r10,PACA_EXGEN+EX_R10(r13)
std r11,PACA_EXGEN+EX_R11(r13)
std r12,PACA_EXGEN+EX_R12(r13)
GET_SCRATCH0(r10)
ld r11,PACA_EXSLB+EX_R9(r13)
ld r12,PACA_EXSLB+EX_R3(r13)
std r10,PACA_EXGEN+EX_R13(r13)
std r11,PACA_EXGEN+EX_R9(r13)
std r12,PACA_EXGEN+EX_R3(r13)
clrrdi r12,r13,32
mfmsr r10
mfspr r11,SRR0 /* save SRR0 */
ori r12,r12,slb_miss_user_common@l /* virt addr of handler */
ori r10,r10,MSR_IR|MSR_DR|MSR_RI
mtspr SRR0,r12
mfspr r12,SRR1 /* and SRR1 */
mtspr SRR1,r10
rfid
b . /* prevent spec. execution */
#endif /* __DISABLED__ */
#ifdef CONFIG_KVM_BOOK3S_64_HANDLER
kvmppc_skip_interrupt:
/*
* Here all GPRs are unchanged from when the interrupt happened
* except for r13, which is saved in SPRG_SCRATCH0.
*/
mfspr r13, SPRN_SRR0
addi r13, r13, 4
mtspr SPRN_SRR0, r13
GET_SCRATCH0(r13)
rfid
b .
kvmppc_skip_Hinterrupt:
/*
* Here all GPRs are unchanged from when the interrupt happened
* except for r13, which is saved in SPRG_SCRATCH0.
*/
mfspr r13, SPRN_HSRR0
addi r13, r13, 4
mtspr SPRN_HSRR0, r13
GET_SCRATCH0(r13)
hrfid
b .
#endif
/*
* Code from here down to __end_handlers is invoked from the
* exception prologs above. Because the prologs assemble the
* addresses of these handlers using the LOAD_HANDLER macro,
* which uses an ori instruction, these handlers must be in
* the first 64k of the kernel image.
*/
/*** Common interrupt handlers ***/
STD_EXCEPTION_COMMON(0x100, system_reset, system_reset_exception)
STD_EXCEPTION_COMMON_ASYNC(0x500, hardware_interrupt, do_IRQ)
STD_EXCEPTION_COMMON_ASYNC(0x900, decrementer, timer_interrupt)
STD_EXCEPTION_COMMON(0x980, hdecrementer, hdec_interrupt)
#ifdef CONFIG_PPC_DOORBELL
STD_EXCEPTION_COMMON_ASYNC(0xa00, doorbell_super, doorbell_exception)
#else
STD_EXCEPTION_COMMON_ASYNC(0xa00, doorbell_super, unknown_exception)
#endif
STD_EXCEPTION_COMMON(0xb00, trap_0b, unknown_exception)
STD_EXCEPTION_COMMON(0xd00, single_step, single_step_exception)
STD_EXCEPTION_COMMON(0xe00, trap_0e, unknown_exception)
STD_EXCEPTION_COMMON(0xe40, emulation_assist, emulation_assist_interrupt)
STD_EXCEPTION_COMMON_ASYNC(0xe60, hmi_exception, handle_hmi_exception)
#ifdef CONFIG_PPC_DOORBELL
STD_EXCEPTION_COMMON_ASYNC(0xe80, h_doorbell, doorbell_exception)
#else
STD_EXCEPTION_COMMON_ASYNC(0xe80, h_doorbell, unknown_exception)
#endif
STD_EXCEPTION_COMMON_ASYNC(0xf00, performance_monitor, performance_monitor_exception)
STD_EXCEPTION_COMMON(0x1300, instruction_breakpoint, instruction_breakpoint_exception)
STD_EXCEPTION_COMMON(0x1502, denorm, unknown_exception)
#ifdef CONFIG_ALTIVEC
STD_EXCEPTION_COMMON(0x1700, altivec_assist, altivec_assist_exception)
#else
STD_EXCEPTION_COMMON(0x1700, altivec_assist, unknown_exception)
#endif
#ifdef CONFIG_CBE_RAS
STD_EXCEPTION_COMMON(0x1200, cbe_system_error, cbe_system_error_exception)
STD_EXCEPTION_COMMON(0x1600, cbe_maintenance, cbe_maintenance_exception)
STD_EXCEPTION_COMMON(0x1800, cbe_thermal, cbe_thermal_exception)
#endif /* CONFIG_CBE_RAS */
/*
* Relocation-on interrupts: A subset of the interrupts can be delivered
* with IR=1/DR=1, if AIL==2 and MSR.HV won't be changed by delivering
* it. Addresses are the same as the original interrupt addresses, but
* offset by 0xc000000000004000.
* It's impossible to receive interrupts below 0x300 via this mechanism.
* KVM: None of these traps are from the guest ; anything that escalated
* to HV=1 from HV=0 is delivered via real mode handlers.
*/
/*
* This uses the standard macro, since the original 0x300 vector
* only has extra guff for STAB-based processors -- which never
* come here.
*/
STD_RELON_EXCEPTION_PSERIES(0x4300, 0x300, data_access)
. = 0x4380
.globl data_access_slb_relon_pSeries
data_access_slb_relon_pSeries:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXSLB)
EXCEPTION_PROLOG_1(PACA_EXSLB, NOTEST, 0x380)
std r3,PACA_EXSLB+EX_R3(r13)
mfspr r3,SPRN_DAR
mfspr r12,SPRN_SRR1
#ifndef CONFIG_RELOCATABLE
b slb_miss_realmode
#else
/*
* We can't just use a direct branch to slb_miss_realmode
* because the distance from here to there depends on where
* the kernel ends up being put.
*/
mfctr r11
ld r10,PACAKBASE(r13)
LOAD_HANDLER(r10, slb_miss_realmode)
mtctr r10
bctr
#endif
STD_RELON_EXCEPTION_PSERIES(0x4400, 0x400, instruction_access)
. = 0x4480
.globl instruction_access_slb_relon_pSeries
instruction_access_slb_relon_pSeries:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXSLB)
EXCEPTION_PROLOG_1(PACA_EXSLB, NOTEST, 0x480)
std r3,PACA_EXSLB+EX_R3(r13)
mfspr r3,SPRN_SRR0 /* SRR0 is faulting address */
mfspr r12,SPRN_SRR1
#ifndef CONFIG_RELOCATABLE
b slb_miss_realmode
#else
mfctr r11
ld r10,PACAKBASE(r13)
LOAD_HANDLER(r10, slb_miss_realmode)
mtctr r10
bctr
#endif
. = 0x4500
.globl hardware_interrupt_relon_pSeries;
.globl hardware_interrupt_relon_hv;
hardware_interrupt_relon_pSeries:
hardware_interrupt_relon_hv:
BEGIN_FTR_SECTION
_MASKABLE_RELON_EXCEPTION_PSERIES(0x502, hardware_interrupt, EXC_HV, SOFTEN_TEST_HV)
FTR_SECTION_ELSE
_MASKABLE_RELON_EXCEPTION_PSERIES(0x500, hardware_interrupt, EXC_STD, SOFTEN_TEST_PR)
ALT_FTR_SECTION_END_IFSET(CPU_FTR_HVMODE)
STD_RELON_EXCEPTION_PSERIES(0x4600, 0x600, alignment)
STD_RELON_EXCEPTION_PSERIES(0x4700, 0x700, program_check)
STD_RELON_EXCEPTION_PSERIES(0x4800, 0x800, fp_unavailable)
MASKABLE_RELON_EXCEPTION_PSERIES(0x4900, 0x900, decrementer)
STD_RELON_EXCEPTION_HV(0x4980, 0x982, hdecrementer)
MASKABLE_RELON_EXCEPTION_PSERIES(0x4a00, 0xa00, doorbell_super)
STD_RELON_EXCEPTION_PSERIES(0x4b00, 0xb00, trap_0b)
. = 0x4c00
.globl system_call_relon_pSeries
system_call_relon_pSeries:
HMT_MEDIUM
SYSCALL_PSERIES_1
SYSCALL_PSERIES_2_DIRECT
SYSCALL_PSERIES_3
STD_RELON_EXCEPTION_PSERIES(0x4d00, 0xd00, single_step)
. = 0x4e00
b . /* Can't happen, see v2.07 Book III-S section 6.5 */
. = 0x4e20
b . /* Can't happen, see v2.07 Book III-S section 6.5 */
. = 0x4e40
emulation_assist_relon_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b emulation_assist_relon_hv
. = 0x4e60
b . /* Can't happen, see v2.07 Book III-S section 6.5 */
. = 0x4e80
h_doorbell_relon_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b h_doorbell_relon_hv
. = 0x4f00
performance_monitor_relon_pseries_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b performance_monitor_relon_pSeries
. = 0x4f20
altivec_unavailable_relon_pseries_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b altivec_unavailable_relon_pSeries
. = 0x4f40
vsx_unavailable_relon_pseries_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b vsx_unavailable_relon_pSeries
. = 0x4f60
facility_unavailable_relon_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b facility_unavailable_relon_pSeries
. = 0x4f80
hv_facility_unavailable_relon_trampoline:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b hv_facility_unavailable_relon_hv
STD_RELON_EXCEPTION_PSERIES(0x5300, 0x1300, instruction_breakpoint)
#ifdef CONFIG_PPC_DENORMALISATION
. = 0x5500
b denorm_exception_hv
#endif
STD_RELON_EXCEPTION_PSERIES(0x5700, 0x1700, altivec_assist)
/* Other future vectors */
.align 7
.globl __end_interrupts
__end_interrupts:
.align 7
system_call_entry_direct:
#if defined(CONFIG_RELOCATABLE)
/* The first level prologue may have used LR to get here, saving
* orig in r10. To save hacking/ifdeffing common code, restore here.
*/
mtlr r10
#endif
system_call_entry:
b system_call_common
ppc64_runlatch_on_trampoline:
b __ppc64_runlatch_on
/*
* Here r13 points to the paca, r9 contains the saved CR,
* SRR0 and SRR1 are saved in r11 and r12,
* r9 - r13 are saved in paca->exgen.
*/
.align 7
.globl data_access_common
data_access_common:
mfspr r10,SPRN_DAR
std r10,PACA_EXGEN+EX_DAR(r13)
mfspr r10,SPRN_DSISR
stw r10,PACA_EXGEN+EX_DSISR(r13)
EXCEPTION_PROLOG_COMMON(0x300, PACA_EXGEN)
RECONCILE_IRQ_STATE(r10, r11)
ld r12,_MSR(r1)
ld r3,PACA_EXGEN+EX_DAR(r13)
lwz r4,PACA_EXGEN+EX_DSISR(r13)
li r5,0x300
b do_hash_page /* Try to handle as hpte fault */
.align 7
.globl h_data_storage_common
h_data_storage_common:
mfspr r10,SPRN_HDAR
std r10,PACA_EXGEN+EX_DAR(r13)
mfspr r10,SPRN_HDSISR
stw r10,PACA_EXGEN+EX_DSISR(r13)
EXCEPTION_PROLOG_COMMON(0xe00, PACA_EXGEN)
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl unknown_exception
b ret_from_except
.align 7
.globl instruction_access_common
instruction_access_common:
EXCEPTION_PROLOG_COMMON(0x400, PACA_EXGEN)
RECONCILE_IRQ_STATE(r10, r11)
ld r12,_MSR(r1)
ld r3,_NIP(r1)
andis. r4,r12,0x5820
li r5,0x400
b do_hash_page /* Try to handle as hpte fault */
STD_EXCEPTION_COMMON(0xe20, h_instr_storage, unknown_exception)
/*
* Here is the common SLB miss user that is used when going to virtual
* mode for SLB misses, that is currently not used
*/
#ifdef __DISABLED__
.align 7
.globl slb_miss_user_common
slb_miss_user_common:
mflr r10
std r3,PACA_EXGEN+EX_DAR(r13)
stw r9,PACA_EXGEN+EX_CCR(r13)
std r10,PACA_EXGEN+EX_LR(r13)
std r11,PACA_EXGEN+EX_SRR0(r13)
bl slb_allocate_user
ld r10,PACA_EXGEN+EX_LR(r13)
ld r3,PACA_EXGEN+EX_R3(r13)
lwz r9,PACA_EXGEN+EX_CCR(r13)
ld r11,PACA_EXGEN+EX_SRR0(r13)
mtlr r10
beq- slb_miss_fault
andi. r10,r12,MSR_RI /* check for unrecoverable exception */
beq- unrecov_user_slb
mfmsr r10
.machine push
.machine "power4"
mtcrf 0x80,r9
.machine pop
clrrdi r10,r10,2 /* clear RI before setting SRR0/1 */
mtmsrd r10,1
mtspr SRR0,r11
mtspr SRR1,r12
ld r9,PACA_EXGEN+EX_R9(r13)
ld r10,PACA_EXGEN+EX_R10(r13)
ld r11,PACA_EXGEN+EX_R11(r13)
ld r12,PACA_EXGEN+EX_R12(r13)
ld r13,PACA_EXGEN+EX_R13(r13)
rfid
b .
slb_miss_fault:
EXCEPTION_PROLOG_COMMON(0x380, PACA_EXGEN)
ld r4,PACA_EXGEN+EX_DAR(r13)
li r5,0
std r4,_DAR(r1)
std r5,_DSISR(r1)
b handle_page_fault
unrecov_user_slb:
EXCEPTION_PROLOG_COMMON(0x4200, PACA_EXGEN)
RECONCILE_IRQ_STATE(r10, r11)
bl save_nvgprs
1: addi r3,r1,STACK_FRAME_OVERHEAD
bl unrecoverable_exception
b 1b
#endif /* __DISABLED__ */
/*
* Machine check is different because we use a different
* save area: PACA_EXMC instead of PACA_EXGEN.
*/
.align 7
.globl machine_check_common
machine_check_common:
mfspr r10,SPRN_DAR
std r10,PACA_EXGEN+EX_DAR(r13)
mfspr r10,SPRN_DSISR
stw r10,PACA_EXGEN+EX_DSISR(r13)
EXCEPTION_PROLOG_COMMON(0x200, PACA_EXMC)
FINISH_NAP
RECONCILE_IRQ_STATE(r10, r11)
ld r3,PACA_EXGEN+EX_DAR(r13)
lwz r4,PACA_EXGEN+EX_DSISR(r13)
std r3,_DAR(r1)
std r4,_DSISR(r1)
bl save_nvgprs
addi r3,r1,STACK_FRAME_OVERHEAD
bl machine_check_exception
b ret_from_except
.align 7
.globl alignment_common
alignment_common:
mfspr r10,SPRN_DAR
std r10,PACA_EXGEN+EX_DAR(r13)
mfspr r10,SPRN_DSISR
stw r10,PACA_EXGEN+EX_DSISR(r13)
EXCEPTION_PROLOG_COMMON(0x600, PACA_EXGEN)
ld r3,PACA_EXGEN+EX_DAR(r13)
lwz r4,PACA_EXGEN+EX_DSISR(r13)
std r3,_DAR(r1)
std r4,_DSISR(r1)
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl alignment_exception
b ret_from_except
.align 7
.globl program_check_common
program_check_common:
EXCEPTION_PROLOG_COMMON(0x700, PACA_EXGEN)
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl program_check_exception
b ret_from_except
.align 7
.globl fp_unavailable_common
fp_unavailable_common:
EXCEPTION_PROLOG_COMMON(0x800, PACA_EXGEN)
bne 1f /* if from user, just load it up */
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl kernel_fp_unavailable_exception
BUG_OPCODE
1:
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
BEGIN_FTR_SECTION
/* Test if 2 TM state bits are zero. If non-zero (ie. userspace was in
* transaction), go do TM stuff
*/
rldicl. r0, r12, (64-MSR_TS_LG), (64-2)
bne- 2f
END_FTR_SECTION_IFSET(CPU_FTR_TM)
#endif
bl load_up_fpu
b fast_exception_return
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
2: /* User process was in a transaction */
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl fp_unavailable_tm
b ret_from_except
#endif
.align 7
.globl altivec_unavailable_common
altivec_unavailable_common:
EXCEPTION_PROLOG_COMMON(0xf20, PACA_EXGEN)
#ifdef CONFIG_ALTIVEC
BEGIN_FTR_SECTION
beq 1f
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
BEGIN_FTR_SECTION_NESTED(69)
/* Test if 2 TM state bits are zero. If non-zero (ie. userspace was in
* transaction), go do TM stuff
*/
rldicl. r0, r12, (64-MSR_TS_LG), (64-2)
bne- 2f
END_FTR_SECTION_NESTED(CPU_FTR_TM, CPU_FTR_TM, 69)
#endif
bl load_up_altivec
b fast_exception_return
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
2: /* User process was in a transaction */
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl altivec_unavailable_tm
b ret_from_except
#endif
1:
END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
#endif
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl altivec_unavailable_exception
b ret_from_except
.align 7
.globl vsx_unavailable_common
vsx_unavailable_common:
EXCEPTION_PROLOG_COMMON(0xf40, PACA_EXGEN)
#ifdef CONFIG_VSX
BEGIN_FTR_SECTION
beq 1f
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
BEGIN_FTR_SECTION_NESTED(69)
/* Test if 2 TM state bits are zero. If non-zero (ie. userspace was in
* transaction), go do TM stuff
*/
rldicl. r0, r12, (64-MSR_TS_LG), (64-2)
bne- 2f
END_FTR_SECTION_NESTED(CPU_FTR_TM, CPU_FTR_TM, 69)
#endif
b load_up_vsx
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
2: /* User process was in a transaction */
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl vsx_unavailable_tm
b ret_from_except
#endif
1:
END_FTR_SECTION_IFSET(CPU_FTR_VSX)
#endif
bl save_nvgprs
RECONCILE_IRQ_STATE(r10, r11)
addi r3,r1,STACK_FRAME_OVERHEAD
bl vsx_unavailable_exception
b ret_from_except
STD_EXCEPTION_COMMON(0xf60, facility_unavailable, facility_unavailable_exception)
STD_EXCEPTION_COMMON(0xf80, hv_facility_unavailable, facility_unavailable_exception)
.align 7
.globl __end_handlers
__end_handlers:
/* Equivalents to the above handlers for relocation-on interrupt vectors */
STD_RELON_EXCEPTION_HV_OOL(0xe40, emulation_assist)
MASKABLE_RELON_EXCEPTION_HV_OOL(0xe80, h_doorbell)
STD_RELON_EXCEPTION_PSERIES_OOL(0xf00, performance_monitor)
STD_RELON_EXCEPTION_PSERIES_OOL(0xf20, altivec_unavailable)
STD_RELON_EXCEPTION_PSERIES_OOL(0xf40, vsx_unavailable)
STD_RELON_EXCEPTION_PSERIES_OOL(0xf60, facility_unavailable)
STD_RELON_EXCEPTION_HV_OOL(0xf80, hv_facility_unavailable)
#if defined(CONFIG_PPC_PSERIES) || defined(CONFIG_PPC_POWERNV)
/*
* Data area reserved for FWNMI option.
* This address (0x7000) is fixed by the RPA.
*/
.= 0x7000
.globl fwnmi_data_area
fwnmi_data_area:
/* pseries and powernv need to keep the whole page from
* 0x7000 to 0x8000 free for use by the firmware
*/
. = 0x8000
#endif /* defined(CONFIG_PPC_PSERIES) || defined(CONFIG_PPC_POWERNV) */
.globl hmi_exception_early
hmi_exception_early:
EXCEPTION_PROLOG_1(PACA_EXGEN, NOTEST, 0xe60)
mr r10,r1 /* Save r1 */
ld r1,PACAEMERGSP(r13) /* Use emergency stack */
subi r1,r1,INT_FRAME_SIZE /* alloc stack frame */
std r9,_CCR(r1) /* save CR in stackframe */
mfspr r11,SPRN_HSRR0 /* Save HSRR0 */
std r11,_NIP(r1) /* save HSRR0 in stackframe */
mfspr r12,SPRN_HSRR1 /* Save SRR1 */
std r12,_MSR(r1) /* save SRR1 in stackframe */
std r10,0(r1) /* make stack chain pointer */
std r0,GPR0(r1) /* save r0 in stackframe */
std r10,GPR1(r1) /* save r1 in stackframe */
EXCEPTION_PROLOG_COMMON_2(PACA_EXGEN)
EXCEPTION_PROLOG_COMMON_3(0xe60)
addi r3,r1,STACK_FRAME_OVERHEAD
bl hmi_exception_realmode
/* Windup the stack. */
/* Move original HSRR0 and HSRR1 into the respective regs */
ld r9,_MSR(r1)
mtspr SPRN_HSRR1,r9
ld r3,_NIP(r1)
mtspr SPRN_HSRR0,r3
ld r9,_CTR(r1)
mtctr r9
ld r9,_XER(r1)
mtxer r9
ld r9,_LINK(r1)
mtlr r9
REST_GPR(0, r1)
REST_8GPRS(2, r1)
REST_GPR(10, r1)
ld r11,_CCR(r1)
mtcr r11
REST_GPR(11, r1)
REST_2GPRS(12, r1)
/* restore original r1. */
ld r1,GPR1(r1)
/*
* Go to virtual mode and pull the HMI event information from
* firmware.
*/
.globl hmi_exception_after_realmode
hmi_exception_after_realmode:
SET_SCRATCH0(r13)
EXCEPTION_PROLOG_0(PACA_EXGEN)
b hmi_exception_hv
#ifdef CONFIG_PPC_POWERNV
_GLOBAL(opal_mc_secondary_handler)
HMT_MEDIUM_PPR_DISCARD
SET_SCRATCH0(r13)
GET_PACA(r13)
clrldi r3,r3,2
tovirt(r3,r3)
std r3,PACA_OPAL_MC_EVT(r13)
ld r13,OPAL_MC_SRR0(r3)
mtspr SPRN_SRR0,r13
ld r13,OPAL_MC_SRR1(r3)
mtspr SPRN_SRR1,r13
ld r3,OPAL_MC_GPR3(r3)
GET_SCRATCH0(r13)
b machine_check_pSeries
#endif /* CONFIG_PPC_POWERNV */
#define MACHINE_CHECK_HANDLER_WINDUP \
/* Clear MSR_RI before setting SRR0 and SRR1. */\
li r0,MSR_RI; \
mfmsr r9; /* get MSR value */ \
andc r9,r9,r0; \
mtmsrd r9,1; /* Clear MSR_RI */ \
/* Move original SRR0 and SRR1 into the respective regs */ \
ld r9,_MSR(r1); \
mtspr SPRN_SRR1,r9; \
ld r3,_NIP(r1); \
mtspr SPRN_SRR0,r3; \
ld r9,_CTR(r1); \
mtctr r9; \
ld r9,_XER(r1); \
mtxer r9; \
ld r9,_LINK(r1); \
mtlr r9; \
REST_GPR(0, r1); \
REST_8GPRS(2, r1); \
REST_GPR(10, r1); \
ld r11,_CCR(r1); \
mtcr r11; \
/* Decrement paca->in_mce. */ \
lhz r12,PACA_IN_MCE(r13); \
subi r12,r12,1; \
sth r12,PACA_IN_MCE(r13); \
REST_GPR(11, r1); \
REST_2GPRS(12, r1); \
/* restore original r1. */ \
ld r1,GPR1(r1)
/*
* Handle machine check early in real mode. We come here with
* ME=1, MMU (IR=0 and DR=0) off and using MC emergency stack.
*/
.align 7
.globl machine_check_handle_early
machine_check_handle_early:
std r0,GPR0(r1) /* Save r0 */
EXCEPTION_PROLOG_COMMON_3(0x200)
bl save_nvgprs
addi r3,r1,STACK_FRAME_OVERHEAD
bl machine_check_early
std r3,RESULT(r1) /* Save result */
ld r12,_MSR(r1)
#ifdef CONFIG_PPC_P7_NAP
/*
* Check if thread was in power saving mode. We come here when any
* of the following is true:
* a. thread wasn't in power saving mode
* b. thread was in power saving mode with no state loss or
* supervisor state loss
*
* Go back to nap again if (b) is true.
*/
rlwinm. r11,r12,47-31,30,31 /* Was it in power saving mode? */
beq 4f /* No, it wasn;t */
/* Thread was in power saving mode. Go back to nap again. */
cmpwi r11,2
bne 3f
/* Supervisor state loss */
li r0,1
stb r0,PACA_NAPSTATELOST(r13)
3: bl machine_check_queue_event
MACHINE_CHECK_HANDLER_WINDUP
GET_PACA(r13)
ld r1,PACAR1(r13)
b power7_enter_nap_mode
4:
#endif
/*
* Check if we are coming from hypervisor userspace. If yes then we
* continue in host kernel in V mode to deliver the MC event.
*/
rldicl. r11,r12,4,63 /* See if MC hit while in HV mode. */
beq 5f
andi. r11,r12,MSR_PR /* See if coming from user. */
bne 9f /* continue in V mode if we are. */
5:
#ifdef CONFIG_KVM_BOOK3S_64_HANDLER
/*
* We are coming from kernel context. Check if we are coming from
* guest. if yes, then we can continue. We will fall through
* do_kvm_200->kvmppc_interrupt to deliver the MC event to guest.
*/
lbz r11,HSTATE_IN_GUEST(r13)
cmpwi r11,0 /* Check if coming from guest */
bne 9f /* continue if we are. */
#endif
/*
* At this point we are not sure about what context we come from.
* Queue up the MCE event and return from the interrupt.
* But before that, check if this is an un-recoverable exception.
* If yes, then stay on emergency stack and panic.
*/
andi. r11,r12,MSR_RI
bne 2f
1: mfspr r11,SPRN_SRR0
ld r10,PACAKBASE(r13)
LOAD_HANDLER(r10,unrecover_mce)
mtspr SPRN_SRR0,r10
ld r10,PACAKMSR(r13)
/*
* We are going down. But there are chances that we might get hit by
* another MCE during panic path and we may run into unstable state
* with no way out. Hence, turn ME bit off while going down, so that
* when another MCE is hit during panic path, system will checkstop
* and hypervisor will get restarted cleanly by SP.
*/
li r3,MSR_ME
andc r10,r10,r3 /* Turn off MSR_ME */
mtspr SPRN_SRR1,r10
rfid
b .
2:
/*
* Check if we have successfully handled/recovered from error, if not
* then stay on emergency stack and panic.
*/
ld r3,RESULT(r1) /* Load result */
cmpdi r3,0 /* see if we handled MCE successfully */
beq 1b /* if !handled then panic */
/*
* Return from MC interrupt.
* Queue up the MCE event so that we can log it later, while
* returning from kernel or opal call.
*/
bl machine_check_queue_event
MACHINE_CHECK_HANDLER_WINDUP
rfid
9:
/* Deliver the machine check to host kernel in V mode. */
MACHINE_CHECK_HANDLER_WINDUP
b machine_check_pSeries
unrecover_mce:
/* Invoke machine_check_exception to print MCE event and panic. */
addi r3,r1,STACK_FRAME_OVERHEAD
bl machine_check_exception
/*
* We will not reach here. Even if we did, there is no way out. Call
* unrecoverable_exception and die.
*/
1: addi r3,r1,STACK_FRAME_OVERHEAD
bl unrecoverable_exception
b 1b
/*
* r13 points to the PACA, r9 contains the saved CR,
* r12 contain the saved SRR1, SRR0 is still ready for return
* r3 has the faulting address
* r9 - r13 are saved in paca->exslb.
* r3 is saved in paca->slb_r3
* We assume we aren't going to take any exceptions during this procedure.
*/
slb_miss_realmode:
mflr r10
#ifdef CONFIG_RELOCATABLE
mtctr r11
#endif
stw r9,PACA_EXSLB+EX_CCR(r13) /* save CR in exc. frame */
std r10,PACA_EXSLB+EX_LR(r13) /* save LR */
bl slb_allocate_realmode
/* All done -- return from exception. */
ld r10,PACA_EXSLB+EX_LR(r13)
ld r3,PACA_EXSLB+EX_R3(r13)
lwz r9,PACA_EXSLB+EX_CCR(r13) /* get saved CR */
mtlr r10
andi. r10,r12,MSR_RI /* check for unrecoverable exception */
beq- 2f
.machine push
.machine "power4"
mtcrf 0x80,r9
mtcrf 0x01,r9 /* slb_allocate uses cr0 and cr7 */
.machine pop
RESTORE_PPR_PACA(PACA_EXSLB, r9)
ld r9,PACA_EXSLB+EX_R9(r13)
ld r10,PACA_EXSLB+EX_R10(r13)
ld r11,PACA_EXSLB+EX_R11(r13)
ld r12,PACA_EXSLB+EX_R12(r13)
ld r13,PACA_EXSLB+EX_R13(r13)
rfid
b . /* prevent speculative execution */
2: mfspr r11,SPRN_SRR0
ld r10,PACAKBASE(r13)
LOAD_HANDLER(r10,unrecov_slb)
mtspr SPRN_SRR0,r10
ld r10,PACAKMSR(r13)
mtspr SPRN_SRR1,r10
rfid
b .
unrecov_slb:
EXCEPTION_PROLOG_COMMON(0x4100, PACA_EXSLB)
RECONCILE_IRQ_STATE(r10, r11)
bl save_nvgprs
1: addi r3,r1,STACK_FRAME_OVERHEAD
bl unrecoverable_exception
b 1b
#ifdef CONFIG_PPC_970_NAP
power4_fixup_nap:
andc r9,r9,r10
std r9,TI_LOCAL_FLAGS(r11)
ld r10,_LINK(r1) /* make idle task do the */
std r10,_NIP(r1) /* equivalent of a blr */
blr
#endif
/*
* Hash table stuff
*/
.align 7
do_hash_page:
std r3,_DAR(r1)
std r4,_DSISR(r1)
andis. r0,r4,0xa410 /* weird error? */
bne- handle_page_fault /* if not, try to insert a HPTE */
andis. r0,r4,DSISR_DABRMATCH@h
bne- handle_dabr_fault
CURRENT_THREAD_INFO(r11, r1)
lwz r0,TI_PREEMPT(r11) /* If we're in an "NMI" */
andis. r0,r0,NMI_MASK@h /* (i.e. an irq when soft-disabled) */
bne 77f /* then don't call hash_page now */
/*
* We need to set the _PAGE_USER bit if MSR_PR is set or if we are
* accessing a userspace segment (even from the kernel). We assume
* kernel addresses always have the high bit set.
*/
rlwinm r4,r4,32-25+9,31-9,31-9 /* DSISR_STORE -> _PAGE_RW */
rotldi r0,r3,15 /* Move high bit into MSR_PR posn */
orc r0,r12,r0 /* MSR_PR | ~high_bit */
rlwimi r4,r0,32-13,30,30 /* becomes _PAGE_USER access bit */
ori r4,r4,1 /* add _PAGE_PRESENT */
rlwimi r4,r5,22+2,31-2,31-2 /* Set _PAGE_EXEC if trap is 0x400 */
/*
* r3 contains the faulting address
* r4 contains the required access permissions
* r5 contains the trap number
*
* at return r3 = 0 for success, 1 for page fault, negative for error
*/
bl hash_page /* build HPTE if possible */
cmpdi r3,0 /* see if hash_page succeeded */
/* Success */
beq fast_exc_return_irq /* Return from exception on success */
/* Error */
blt- 13f
/* Here we have a page fault that hash_page can't handle. */
handle_page_fault:
11: ld r4,_DAR(r1)
ld r5,_DSISR(r1)
addi r3,r1,STACK_FRAME_OVERHEAD
bl do_page_fault
cmpdi r3,0
beq+ 12f
bl save_nvgprs
mr r5,r3
addi r3,r1,STACK_FRAME_OVERHEAD
lwz r4,_DAR(r1)
bl bad_page_fault
b ret_from_except
/* We have a data breakpoint exception - handle it */
handle_dabr_fault:
bl save_nvgprs
ld r4,_DAR(r1)
ld r5,_DSISR(r1)
addi r3,r1,STACK_FRAME_OVERHEAD
bl do_break
12: b ret_from_except_lite
/* We have a page fault that hash_page could handle but HV refused
* the PTE insertion
*/
13: bl save_nvgprs
mr r5,r3
addi r3,r1,STACK_FRAME_OVERHEAD
ld r4,_DAR(r1)
bl low_hash_fault
b ret_from_except
/*
* We come here as a result of a DSI at a point where we don't want
* to call hash_page, such as when we are accessing memory (possibly
* user memory) inside a PMU interrupt that occurred while interrupts
* were soft-disabled. We want to invoke the exception handler for
* the access, or panic if there isn't a handler.
*/
77: bl save_nvgprs
mr r4,r3
addi r3,r1,STACK_FRAME_OVERHEAD
li r5,SIGSEGV
bl bad_page_fault
b ret_from_except
/*
* Here we have detected that the kernel stack pointer is bad.
* R9 contains the saved CR, r13 points to the paca,
* r10 contains the (bad) kernel stack pointer,
* r11 and r12 contain the saved SRR0 and SRR1.
* We switch to using an emergency stack, save the registers there,
* and call kernel_bad_stack(), which panics.
*/
bad_stack:
ld r1,PACAEMERGSP(r13)
subi r1,r1,64+INT_FRAME_SIZE
std r9,_CCR(r1)
std r10,GPR1(r1)
std r11,_NIP(r1)
std r12,_MSR(r1)
mfspr r11,SPRN_DAR
mfspr r12,SPRN_DSISR
std r11,_DAR(r1)
std r12,_DSISR(r1)
mflr r10
mfctr r11
mfxer r12
std r10,_LINK(r1)
std r11,_CTR(r1)
std r12,_XER(r1)
SAVE_GPR(0,r1)
SAVE_GPR(2,r1)
ld r10,EX_R3(r3)
std r10,GPR3(r1)
SAVE_GPR(4,r1)
SAVE_4GPRS(5,r1)
ld r9,EX_R9(r3)
ld r10,EX_R10(r3)
SAVE_2GPRS(9,r1)
ld r9,EX_R11(r3)
ld r10,EX_R12(r3)
ld r11,EX_R13(r3)
std r9,GPR11(r1)
std r10,GPR12(r1)
std r11,GPR13(r1)
BEGIN_FTR_SECTION
ld r10,EX_CFAR(r3)
std r10,ORIG_GPR3(r1)
END_FTR_SECTION_IFSET(CPU_FTR_CFAR)
SAVE_8GPRS(14,r1)
SAVE_10GPRS(22,r1)
lhz r12,PACA_TRAP_SAVE(r13)
std r12,_TRAP(r1)
addi r11,r1,INT_FRAME_SIZE
std r11,0(r1)
li r12,0
std r12,0(r11)
ld r2,PACATOC(r13)
ld r11,exception_marker@toc(r2)
std r12,RESULT(r1)
std r11,STACK_FRAME_OVERHEAD-16(r1)
1: addi r3,r1,STACK_FRAME_OVERHEAD
bl kernel_bad_stack
b 1b