asgardius/android_kernel_samsung_heroqlte
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
android_kernel_samsung_hero.../drivers/usb/phy/phy-msm-qusb.c
HackerOO7 2bd1731e0a init: OSRC G9300ZCU2APF7
2016-08-17 16:41:52 +08:00

1137 lines
31 KiB
C
Raw Permalink Blame History

/*
* Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/clk.h>
#include <linux/clk/msm-clk.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>
#include <linux/usb/phy.h>
#include <linux/usb/msm_hsusb.h>
#define QUSB2PHY_PLL_STATUS 0x38
#define QUSB2PHY_PLL_LOCK BIT(5)
#define QUSB2PHY_PORT_QC1 0x70
#define VDM_SRC_EN BIT(4)
#define VDP_SRC_EN BIT(2)
#define QUSB2PHY_PORT_QC2 0x74
#define RDM_UP_EN BIT(1)
#define RDP_UP_EN BIT(3)
#define RPUM_LOW_EN BIT(4)
#define RPUP_LOW_EN BIT(5)
#define QUSB2PHY_PORT_POWERDOWN 0xB4
#define CLAMP_N_EN BIT(5)
#define FREEZIO_N BIT(1)
#define POWER_DOWN BIT(0)
#define QUSB2PHY_PORT_UTMI_CTRL1 0xC0
#define TERM_SELECT BIT(4)
#define XCVR_SELECT_FS BIT(2)
#define OP_MODE_NON_DRIVE BIT(0)
#define QUSB2PHY_PORT_UTMI_CTRL2 0xC4
#define UTMI_ULPI_SEL BIT(7)
#define UTMI_TEST_MUX_SEL BIT(6)
#define QUSB2PHY_PORT_TUNE1 0x80
#define QUSB2PHY_PORT_TUNE2 0x84
#define QUSB2PHY_PORT_TUNE3 0x88
#define QUSB2PHY_PORT_TUNE4 0x8C
/* In case Efuse register shows zero, use this value */
#define TUNE2_DEFAULT_HIGH_NIBBLE 0xB
#define TUNE2_DEFAULT_LOW_NIBBLE 0x3
#ifdef CONFIG_USB_ANDROID_SAMSUNG_COMPOSITE
#define SS_SYNC_VALUE 0x8
#define SS_LOW_TUNE2 0x0
#endif
/* Get TUNE2's high nibble value read from efuse */
#define TUNE2_HIGH_NIBBLE_VAL(val, pos, mask) ((val >> pos) & mask)
#define QUSB2PHY_PORT_INTR_CTRL 0xBC
#define CHG_DET_INTR_EN BIT(4)
#define DMSE_INTR_HIGH_SEL BIT(3)
#define DMSE_INTR_EN BIT(2)
#define DPSE_INTR_HIGH_SEL BIT(1)
#define DPSE_INTR_EN BIT(0)
#define QUSB2PHY_PORT_UTMI_STATUS 0xF4
#define LINESTATE_DP BIT(0)
#define LINESTATE_DM BIT(1)
#define HS_PHY_CTRL_REG 0x10
#define UTMI_OTG_VBUS_VALID BIT(20)
#define SW_SESSVLD_SEL BIT(28)
#define QUSB2PHY_1P8_VOL_MIN 1800000 /* uV */
#define QUSB2PHY_1P8_VOL_MAX 1800000 /* uV */
#define QUSB2PHY_1P8_HPM_LOAD 30000 /* uA */
#define QUSB2PHY_3P3_VOL_MIN 3075000 /* uV */
#define QUSB2PHY_3P3_VOL_MAX 3200000 /* uV */
#define QUSB2PHY_3P3_HPM_LOAD 30000 /* uA */
#define QUSB2PHY_REFCLK_ENABLE BIT(0)
#define QUSB2PHY_PLL_TEST 0x04
#define ENABLE_SE_CLK 0x80
unsigned int tune2;
module_param(tune2, uint, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(tune2, "QUSB PHY TUNE2");
struct qusb_phy {
struct usb_phy phy;
void __iomem *base;
void __iomem *qscratch_base;
void __iomem *tune2_efuse_reg;
void __iomem *ref_clk_base;
struct clk *ref_clk_src;
struct clk *ref_clk;
struct clk *cfg_ahb_clk;
struct clk *phy_reset;
struct regulator *vdd;
struct regulator *vdda33;
struct regulator *vdda18;
int vdd_levels[3]; /* none, low, high */
int init_seq_len;
int *qusb_phy_init_seq;
u32 tune2_val;
int tune2_efuse_bit_pos;
int tune2_efuse_num_of_bits;
bool power_enabled;
bool clocks_enabled;
bool cable_connected;
bool suspended;
bool ulpi_mode;
bool rm_pulldown;
/* emulation targets specific */
void __iomem *emu_phy_base;
bool emulation;
int *emu_init_seq;
int emu_init_seq_len;
int *phy_pll_reset_seq;
int phy_pll_reset_seq_len;
int *emu_dcm_reset_seq;
int emu_dcm_reset_seq_len;
spinlock_t pulse_lock;
};
static void qusb_phy_enable_clocks(struct qusb_phy *qphy, bool on)
{
dev_dbg(qphy->phy.dev, "%s(): clocks_enabled:%d on:%d\n",
__func__, qphy->clocks_enabled, on);
if (!qphy->clocks_enabled && on) {
clk_prepare_enable(qphy->ref_clk_src);
clk_prepare_enable(qphy->ref_clk);
clk_prepare_enable(qphy->cfg_ahb_clk);
qphy->clocks_enabled = true;
}
if (qphy->clocks_enabled && !on) {
clk_disable_unprepare(qphy->ref_clk);
clk_disable_unprepare(qphy->ref_clk_src);
clk_disable_unprepare(qphy->cfg_ahb_clk);
qphy->clocks_enabled = false;
}
dev_dbg(qphy->phy.dev, "%s(): clocks_enabled:%d\n", __func__,
qphy->clocks_enabled);
}
static int qusb_phy_config_vdd(struct qusb_phy *qphy, int high)
{
int min, ret;
min = high ? 1 : 0; /* low or none? */
ret = regulator_set_voltage(qphy->vdd, qphy->vdd_levels[min],
qphy->vdd_levels[2]);
if (ret) {
dev_err(qphy->phy.dev, "unable to set voltage for qusb vdd\n");
return ret;
}
dev_dbg(qphy->phy.dev, "min_vol:%d max_vol:%d\n",
qphy->vdd_levels[min], qphy->vdd_levels[2]);
return ret;
}
static int qusb_phy_enable_power(struct qusb_phy *qphy, bool on,
bool toggle_vdd)
{
int ret = 0;
dev_dbg(qphy->phy.dev, "%s turn %s regulators. power_enabled:%d\n",
__func__, on ? "on" : "off", qphy->power_enabled);
if (toggle_vdd && qphy->power_enabled == on) {
dev_dbg(qphy->phy.dev, "PHYs' regulators are already ON.\n");
return 0;
}
if (!on)
goto disable_vdda33;
if (toggle_vdd) {
ret = qusb_phy_config_vdd(qphy, true);
if (ret) {
dev_err(qphy->phy.dev, "Unable to config VDD:%d\n",
ret);
goto err_vdd;
}
ret = regulator_enable(qphy->vdd);
if (ret) {
dev_err(qphy->phy.dev, "Unable to enable VDD\n");
goto unconfig_vdd;
}
}
ret = regulator_set_optimum_mode(qphy->vdda18, QUSB2PHY_1P8_HPM_LOAD);
if (ret < 0) {
dev_err(qphy->phy.dev, "Unable to set HPM of vdda18:%d\n", ret);
goto disable_vdd;
}
ret = regulator_set_voltage(qphy->vdda18, QUSB2PHY_1P8_VOL_MIN,
QUSB2PHY_1P8_VOL_MAX);
if (ret) {
dev_err(qphy->phy.dev,
"Unable to set voltage for vdda18:%d\n", ret);
goto put_vdda18_lpm;
}
ret = regulator_enable(qphy->vdda18);
if (ret) {
dev_err(qphy->phy.dev, "Unable to enable vdda18:%d\n", ret);
goto unset_vdda18;
}
ret = regulator_set_optimum_mode(qphy->vdda33, QUSB2PHY_3P3_HPM_LOAD);
if (ret < 0) {
dev_err(qphy->phy.dev, "Unable to set HPM of vdda33:%d\n", ret);
goto disable_vdda18;
}
ret = regulator_set_voltage(qphy->vdda33, QUSB2PHY_3P3_VOL_MIN,
QUSB2PHY_3P3_VOL_MAX);
if (ret) {
dev_err(qphy->phy.dev,
"Unable to set voltage for vdda33:%d\n", ret);
goto put_vdda33_lpm;
}
ret = regulator_enable(qphy->vdda33);
if (ret) {
dev_err(qphy->phy.dev, "Unable to enable vdda33:%d\n", ret);
goto unset_vdd33;
}
if (toggle_vdd)
qphy->power_enabled = true;
pr_debug("%s(): QUSB PHY's regulators are turned ON.\n", __func__);
return ret;
disable_vdda33:
ret = regulator_disable(qphy->vdda33);
if (ret)
dev_err(qphy->phy.dev, "Unable to disable vdda33:%d\n", ret);
unset_vdd33:
ret = regulator_set_voltage(qphy->vdda33, 0, QUSB2PHY_3P3_VOL_MAX);
if (ret)
dev_err(qphy->phy.dev,
"Unable to set (0) voltage for vdda33:%d\n", ret);
put_vdda33_lpm:
ret = regulator_set_optimum_mode(qphy->vdda33, 0);
if (ret < 0)
dev_err(qphy->phy.dev, "Unable to set (0) HPM of vdda33\n");
disable_vdda18:
ret = regulator_disable(qphy->vdda18);
if (ret)
dev_err(qphy->phy.dev, "Unable to disable vdda18:%d\n", ret);
unset_vdda18:
ret = regulator_set_voltage(qphy->vdda18, 0, QUSB2PHY_1P8_VOL_MAX);
if (ret)
dev_err(qphy->phy.dev,
"Unable to set (0) voltage for vdda18:%d\n", ret);
put_vdda18_lpm:
ret = regulator_set_optimum_mode(qphy->vdda18, 0);
if (ret < 0)
dev_err(qphy->phy.dev, "Unable to set LPM of vdda18\n");
disable_vdd:
if (toggle_vdd) {
ret = regulator_disable(qphy->vdd);
if (ret)
dev_err(qphy->phy.dev, "Unable to disable vdd:%d\n",
ret);
unconfig_vdd:
ret = qusb_phy_config_vdd(qphy, false);
if (ret)
dev_err(qphy->phy.dev, "Unable unconfig VDD:%d\n",
ret);
}
err_vdd:
if (toggle_vdd)
qphy->power_enabled = false;
dev_dbg(qphy->phy.dev, "QUSB PHY's regulators are turned OFF.\n");
return ret;
}
#define PHY_PULSE_TIME_USEC 250
static int qusb_phy_update_dpdm(struct usb_phy *phy, int value)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
unsigned long flags;
int ret = 0;
u32 reg;
dev_dbg(phy->dev, "%s value:%d rm_pulldown:%d\n", __func__,
value, qphy->rm_pulldown);
/*
* Need only ahb2phy clock to access QC1 and QC2 registers. Hence
* enable this.
*/
clk_prepare_enable(qphy->cfg_ahb_clk);
switch (value) {
case POWER_SUPPLY_DP_DM_DPF_DMF:
dev_dbg(phy->dev, "POWER_SUPPLY_DP_DM_DPF_DMF\n");
if (!qphy->rm_pulldown) {
ret = qusb_phy_enable_power(qphy, true, false);
if (ret >= 0) {
qphy->rm_pulldown = true;
dev_dbg(phy->dev, "DP_DM_F: rm_pulldown:%d\n",
qphy->rm_pulldown);
}
}
/* Clear QC1 and QC2 registers when rm_pulldown = 1 */
if (qphy->rm_pulldown) {
dev_dbg(phy->dev, "clearing qc1 and qc2 registers.\n");
/* Clear qc1 and qc2 registers */
writel_relaxed(0x00, qphy->base + QUSB2PHY_PORT_QC1);
writel_relaxed(0x00, qphy->base + QUSB2PHY_PORT_QC2);
/* to make sure above write goes through */
mb();
}
break;
case POWER_SUPPLY_DP_DM_DPR_DMR:
dev_dbg(phy->dev, "POWER_SUPPLY_DP_DM_DPR_DMR\n");
if (qphy->rm_pulldown) {
dev_dbg(phy->dev, "clearing qc1 and qc2 registers.\n");
/* Clear qc1 and qc2 registers */
writel_relaxed(0x00, qphy->base + QUSB2PHY_PORT_QC1);
writel_relaxed(0x00, qphy->base + QUSB2PHY_PORT_QC2);
/* to make sure above write goes through */
mb();
ret = qusb_phy_enable_power(qphy, false, false);
if (ret >= 0) {
qphy->rm_pulldown = false;
dev_dbg(phy->dev, "DP_DM_R: rm_pulldown:%d\n",
qphy->rm_pulldown);
}
}
break;
case POWER_SUPPLY_DP_DM_DP0P6_DMF:
dev_dbg(phy->dev, "POWER_SUPPLY_DP_DM_DP0P6_DMF\n");
/* Set DP to 0.6v and DM to High Z state */
writel_relaxed(VDP_SRC_EN, qphy->base + QUSB2PHY_PORT_QC1);
/* complete above write */
mb();
break;
case POWER_SUPPLY_DP_DM_DP0P6_DM3P3:
dev_dbg(phy->dev, "POWER_SUPPLY_DP_DM_DP0PHVDCP_36_DM3P3\n");
/* Set DP to 0.6v */
writel_relaxed(VDP_SRC_EN, qphy->base + QUSB2PHY_PORT_QC1);
/* Set DM to 3.075v */
writel_relaxed(RPUM_LOW_EN | RDM_UP_EN,
qphy->base + QUSB2PHY_PORT_QC2);
/* complete above write */
mb();
break;
case POWER_SUPPLY_DP_DM_DP_PULSE:
dev_dbg(phy->dev, "POWER_SUPPLY_DP_DM_DP_PULSE\n");
spin_lock_irqsave(&qphy->pulse_lock, flags);
/*Set DP to 3.075v, sleep for .25 ms */
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC2);
reg |= (RDP_UP_EN | RPUP_LOW_EN);
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC2);
/* complete above write */
mb();
/*
* It is recommended to wait here to get voltage change on
* DP/DM line.
*/
udelay(PHY_PULSE_TIME_USEC);
/* Set DP to 0.6v, sleep 2-3ms */
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC1);
reg |= VDP_SRC_EN;
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC1);
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC2);
reg &= ~(RDP_UP_EN | RPUP_LOW_EN);
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC2);
/* complete above write */
mb();
spin_unlock_irqrestore(&qphy->pulse_lock, flags);
/*
* It is recommended to wait here to get voltage change on
* DP/DM line.
*/
usleep_range(2000, 3000);
break;
case POWER_SUPPLY_DP_DM_DM_PULSE:
dev_dbg(phy->dev, "POWER_SUPPLY_DP_DM_DM_PULSE\n");
spin_lock_irqsave(&qphy->pulse_lock, flags);
/* Set DM to 0.6v, sleep .25 ms */
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC1);
reg |= VDM_SRC_EN;
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC1);
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC2);
reg &= ~(RDM_UP_EN | RPUM_LOW_EN);
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC2);
/* complete above write */
mb();
/*
* It is recommended to wait here to get voltage change on
* DP/DM line.
*/
udelay(PHY_PULSE_TIME_USEC);
/* DM to 3.075v, sleep 2-3ms */
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC2);
reg |= (RPUM_LOW_EN | RDM_UP_EN);
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC2);
reg = readl_relaxed(qphy->base + QUSB2PHY_PORT_QC1);
reg &= ~VDM_SRC_EN;
writel_relaxed(reg, qphy->base + QUSB2PHY_PORT_QC1);
/* complete above write */
mb();
spin_unlock_irqrestore(&qphy->pulse_lock, flags);
/*
* It is recommended to wait here to get voltage change on
* DP/DM line.
*/
usleep_range(2000, 3000);
break;
default:
ret = -EINVAL;
dev_err(phy->dev, "Invalid power supply property(%d)\n", value);
break;
}
/* Disable ahb2phy clock as it enables above. */
clk_disable_unprepare(qphy->cfg_ahb_clk);
return ret;
}
static void qusb_phy_get_tune2_param(struct qusb_phy *qphy)
{
u8 num_of_bits;
u32 bit_mask = 1;
pr_debug("%s(): num_of_bits:%d bit_pos:%d\n", __func__,
qphy->tune2_efuse_num_of_bits,
qphy->tune2_efuse_bit_pos);
/* get bit mask based on number of bits to use with efuse reg */
if (qphy->tune2_efuse_num_of_bits) {
num_of_bits = qphy->tune2_efuse_num_of_bits;
bit_mask = (bit_mask << num_of_bits) - 1;
}
/*
* Read EFUSE register having TUNE2 parameter's high nibble.
* If efuse register shows value as 0x0, then use default value
* as 0xB as high nibble. Otherwise use efuse register based
* value for this purpose.
*/
qphy->tune2_val = readl_relaxed(qphy->tune2_efuse_reg);
pr_info("%s(): bit_mask:%d efuse based tune2 value:%d\n",
__func__, bit_mask, qphy->tune2_val);
qphy->tune2_val = TUNE2_HIGH_NIBBLE_VAL(qphy->tune2_val,
qphy->tune2_efuse_bit_pos, bit_mask);
if (!qphy->tune2_val)
qphy->tune2_val = TUNE2_DEFAULT_HIGH_NIBBLE;
#ifdef CONFIG_USB_ANDROID_SAMSUNG_COMPOSITE
if (qphy->tune2_val >= SS_SYNC_VALUE) {
qphy->tune2_val = qphy->tune2_val - SS_SYNC_VALUE;
} else {
pr_info("fail to apply SS_SYNC_VALUE. QC efuse based tune2 value is too low.\n");
qphy->tune2_val = SS_LOW_TUNE2;
}
#endif
/* Get TUNE2 byte value using high and low nibble value */
qphy->tune2_val = ((qphy->tune2_val << 0x4) |
TUNE2_DEFAULT_LOW_NIBBLE);
}
static void qusb_phy_write_seq(void __iomem *base, u32 *seq, int cnt,
unsigned long delay)
{
int i;
pr_debug("Seq count:%d\n", cnt);
for (i = 0; i < cnt; i = i+2) {
pr_debug("write 0x%02x to 0x%02x\n", seq[i], seq[i+1]);
writel_relaxed(seq[i], base + seq[i+1]);
if (delay)
usleep_range(delay, (delay + 2000));
}
}
static int qusb_phy_init(struct usb_phy *phy)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
int ret;
dev_dbg(phy->dev, "%s\n", __func__);
ret = qusb_phy_enable_power(qphy, true, true);
if (ret)
return ret;
qusb_phy_enable_clocks(qphy, true);
/*
* ref clock is enabled by default after power on reset. Linux clock
* driver will disable this clock as part of late init if peripheral
* driver(s) does not explicitly votes for it. Linux clock driver also
* does not disable the clock until late init even if peripheral
* driver explicitly requests it and cannot defer the probe until late
* init. Hence, Explicitly disable the clock using register write to
* allow QUSB PHY PLL to lock properly.
*/
if (qphy->ref_clk_base) {
writel_relaxed((readl_relaxed(qphy->ref_clk_base) &
~QUSB2PHY_REFCLK_ENABLE),
qphy->ref_clk_base);
/* Make sure that above write complete to get ref clk OFF */
wmb();
}
/* Perform phy reset */
clk_reset(qphy->phy_reset, CLK_RESET_ASSERT);
usleep_range(100, 150);
clk_reset(qphy->phy_reset, CLK_RESET_DEASSERT);
if (qphy->emulation) {
if (qphy->emu_init_seq)
qusb_phy_write_seq(qphy->emu_phy_base,
qphy->emu_init_seq, qphy->emu_init_seq_len, 0);
if (qphy->qusb_phy_init_seq)
qusb_phy_write_seq(qphy->base, qphy->qusb_phy_init_seq,
qphy->init_seq_len, 0);
/* Wait for 5ms as per QUSB2 RUMI sequence */
usleep_range(5000, 7000);
if (qphy->phy_pll_reset_seq)
qusb_phy_write_seq(qphy->base, qphy->phy_pll_reset_seq,
qphy->phy_pll_reset_seq_len, 10000);
if (qphy->emu_dcm_reset_seq)
qusb_phy_write_seq(qphy->emu_phy_base,
qphy->emu_dcm_reset_seq,
qphy->emu_dcm_reset_seq_len, 10000);
return 0;
}
/* Disable the PHY */
writel_relaxed(CLAMP_N_EN | FREEZIO_N | POWER_DOWN,
qphy->base + QUSB2PHY_PORT_POWERDOWN);
/* configure for ULPI mode if requested */
if (qphy->ulpi_mode)
writel_relaxed(0x0, qphy->base + QUSB2PHY_PORT_UTMI_CTRL2);
if (qphy->qusb_phy_init_seq)
qusb_phy_write_seq(qphy->base, qphy->qusb_phy_init_seq,
qphy->init_seq_len, 0);
/*
* Check for EFUSE value only if tune2_efuse_reg is available
* and try to read EFUSE value only once i.e. not every USB
* cable connect case.
*/
if (qphy->tune2_efuse_reg) {
if (!qphy->tune2_val)
qusb_phy_get_tune2_param(qphy);
pr_debug("%s(): Programming TUNE2 parameter as:%x\n", __func__,
qphy->tune2_val);
writel_relaxed(qphy->tune2_val,
qphy->base + QUSB2PHY_PORT_TUNE2);
}
/* If tune2 modparam set, override tune2 value */
if (tune2) {
pr_debug("%s(): (modparam) TUNE2 val:0x%02x\n",
__func__, tune2);
writel_relaxed(tune2,
qphy->base + QUSB2PHY_PORT_TUNE2);
}
#ifdef CONFIG_USB_HOST_NOTIFY
if(qphy->phy.otg_mode == OTG_MODE_HOST) {
writel_relaxed(0xf8, qphy->base + QUSB2PHY_PORT_TUNE1);
writel_relaxed(0xc3, qphy->base + QUSB2PHY_PORT_TUNE2);
writel_relaxed(0x83, qphy->base + QUSB2PHY_PORT_TUNE3);
}
#endif
#ifdef CONFIG_USB_ANDROID_SAMSUNG_COMPOSITE
pr_info("PHY Tune1:%x,Tune2:%x,Tune3:%x,Tune4:%x",
readb_relaxed(qphy->base + QUSB2PHY_PORT_TUNE1),
readb_relaxed(qphy->base + QUSB2PHY_PORT_TUNE2),
readb_relaxed(qphy->base + QUSB2PHY_PORT_TUNE3),
readb_relaxed(qphy->base + QUSB2PHY_PORT_TUNE4));
#endif
/* ensure above writes are completed before re-enabling PHY */
wmb();
/* Enable the PHY */
writel_relaxed(CLAMP_N_EN | FREEZIO_N,
qphy->base + QUSB2PHY_PORT_POWERDOWN);
/* Ensure above write is completed before turning ON ref clk */
wmb();
/* Require to get phy pll lock successfully */
usleep_range(150, 160);
/* Select PLL_TEST mux for SE clock logic to QUSB PHY */
writel_relaxed(ENABLE_SE_CLK, qphy->base + QUSB2PHY_PLL_TEST);
/* Make sure that above write is completed to get PLL source clock */
wmb();
/* Required to get PHY PLL lock successfully */
usleep_range(100, 110);
if (!(readb_relaxed(qphy->base + QUSB2PHY_PLL_STATUS) &
QUSB2PHY_PLL_LOCK)) {
dev_err(phy->dev, "QUSB PHY PLL LOCK fails:%x\n",
readb_relaxed(qphy->base + QUSB2PHY_PLL_STATUS));
WARN_ON(1);
}
return 0;
}
static void qusb_phy_shutdown(struct usb_phy *phy)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
dev_dbg(phy->dev, "%s\n", __func__);
qusb_phy_enable_clocks(qphy, true);
/* Disable the PHY */
writel_relaxed(CLAMP_N_EN | FREEZIO_N | POWER_DOWN,
qphy->base + QUSB2PHY_PORT_POWERDOWN);
wmb();
qusb_phy_enable_clocks(qphy, false);
}
/**
* Performs QUSB2 PHY suspend/resume functionality.
*
* @uphy - usb phy pointer.
* @suspend - to enable suspend or not. 1 - suspend, 0 - resume
*
*/
static int qusb_phy_set_suspend(struct usb_phy *phy, int suspend)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
u32 linestate = 0, intr_mask = 0;
if (qphy->suspended && suspend) {
dev_dbg(phy->dev, "%s: USB PHY is already suspended\n",
__func__);
return 0;
}
if (suspend) {
/* Bus suspend case */
if (qphy->cable_connected ||
(qphy->phy.flags & PHY_HOST_MODE)) {
/* Clear all interrupts */
writel_relaxed(0x00,
qphy->base + QUSB2PHY_PORT_INTR_CTRL);
linestate = readl_relaxed(qphy->base +
QUSB2PHY_PORT_UTMI_STATUS);
/*
* D+/D- interrupts are level-triggered, but we are
* only interested if the line state changes, so enable
* the high/low trigger based on current state. In
* other words, enable the triggers _opposite_ of what
* the current D+/D- levels are.
* e.g. if currently D+ high, D- low (HS 'J'/Suspend),
* configure the mask to trigger on D+ low OR D- high
*/
intr_mask = DPSE_INTR_EN | DMSE_INTR_EN;
if (!(linestate & LINESTATE_DP)) /* D+ low */
intr_mask |= DPSE_INTR_HIGH_SEL;
if (!(linestate & LINESTATE_DM)) /* D- low */
intr_mask |= DMSE_INTR_HIGH_SEL;
writel_relaxed(intr_mask,
qphy->base + QUSB2PHY_PORT_INTR_CTRL);
qusb_phy_enable_clocks(qphy, false);
} else { /* Disconnect case */
/* Disable all interrupts */
writel_relaxed(0x00,
qphy->base + QUSB2PHY_PORT_INTR_CTRL);
/*
* Phy in non-driving mode leaves Dp and Dm lines in
* high-Z state. Controller power collapse is not
* switching phy to non-driving mode causing charger
* detection failure. Bring phy to non-driving mode by
* overriding controller output via UTMI interface.
*/
writel_relaxed(TERM_SELECT | XCVR_SELECT_FS |
OP_MODE_NON_DRIVE,
qphy->base + QUSB2PHY_PORT_UTMI_CTRL1);
writel_relaxed(UTMI_ULPI_SEL | UTMI_TEST_MUX_SEL,
qphy->base + QUSB2PHY_PORT_UTMI_CTRL2);
qusb_phy_enable_clocks(qphy, false);
qusb_phy_enable_power(qphy, false, true);
}
qphy->suspended = true;
} else {
/* Bus suspend case */
if (qphy->cable_connected ||
(qphy->phy.flags & PHY_HOST_MODE)) {
qusb_phy_enable_clocks(qphy, true);
/* Clear all interrupts on resume */
writel_relaxed(0x00,
qphy->base + QUSB2PHY_PORT_INTR_CTRL);
} else {
qusb_phy_enable_power(qphy, true, true);
qusb_phy_enable_clocks(qphy, true);
}
qphy->suspended = false;
}
return 0;
}
static void qusb_write_readback(void *base, u32 offset,
const u32 mask, u32 val)
{
u32 write_val, tmp = readl_relaxed(base + offset);
tmp &= ~mask; /* retain other bits */
write_val = tmp | val;
writel_relaxed(write_val, base + offset);
/* Read back to see if val was written */
tmp = readl_relaxed(base + offset);
tmp &= mask; /* clear other bits */
if (tmp != val)
pr_err("%s: write: %x to QSCRATCH: %x FAILED\n",
__func__, val, offset);
}
static int qusb_phy_notify_connect(struct usb_phy *phy,
enum usb_device_speed speed)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
qphy->cable_connected = true;
dev_dbg(phy->dev, " cable_connected=%d\n", qphy->cable_connected);
/* Set OTG VBUS Valid from HSPHY to controller */
qusb_write_readback(qphy->qscratch_base, HS_PHY_CTRL_REG,
UTMI_OTG_VBUS_VALID,
UTMI_OTG_VBUS_VALID);
/* Indicate value is driven by UTMI_OTG_VBUS_VALID bit */
qusb_write_readback(qphy->qscratch_base, HS_PHY_CTRL_REG,
SW_SESSVLD_SEL, SW_SESSVLD_SEL);
dev_dbg(phy->dev, "QUSB2 phy connect notification\n");
return 0;
}
static int qusb_phy_notify_disconnect(struct usb_phy *phy,
enum usb_device_speed speed)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
qphy->cable_connected = false;
dev_dbg(phy->dev, " cable_connected=%d\n", qphy->cable_connected);
/* Set OTG VBUS Valid from HSPHY to controller */
qusb_write_readback(qphy->qscratch_base, HS_PHY_CTRL_REG,
UTMI_OTG_VBUS_VALID, 0);
/* Indicate value is driven by UTMI_OTG_VBUS_VALID bit */
qusb_write_readback(qphy->qscratch_base, HS_PHY_CTRL_REG,
SW_SESSVLD_SEL, 0);
dev_dbg(phy->dev, "QUSB2 phy disconnect notification\n");
return 0;
}
#ifdef CONFIG_USB_HOST_NOTIFY
static int qusb_phy_set_mode(struct usb_phy *phy,
enum usb_otg_mode mode)
{
struct qusb_phy *qphy = container_of(phy, struct qusb_phy, phy);
dev_info(phy->dev, "qusb_phy_set_mode, usb_otg_mode=%d\n", mode);
qphy->phy.otg_mode = mode;
return 0;
}
#endif
static int qusb_phy_probe(struct platform_device *pdev)
{
struct qusb_phy *qphy;
struct device *dev = &pdev->dev;
struct resource *res;
int ret = 0, size = 0;
const char *phy_type;
bool hold_phy_reset;
qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
if (!qphy)
return -ENOMEM;
qphy->phy.dev = dev;
spin_lock_init(&qphy->pulse_lock);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"qusb_phy_base");
qphy->base = devm_ioremap_resource(dev, res);
if (IS_ERR(qphy->base))
return PTR_ERR(qphy->base);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"qscratch_base");
if (res) {
qphy->qscratch_base = devm_ioremap_resource(dev, res);
if (IS_ERR(qphy->qscratch_base)) {
dev_dbg(dev, "couldn't ioremap qscratch_base\n");
qphy->qscratch_base = NULL;
}
}
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"emu_phy_base");
if (res) {
qphy->emu_phy_base = devm_ioremap_resource(dev, res);
if (IS_ERR(qphy->emu_phy_base)) {
dev_dbg(dev, "couldn't ioremap emu_phy_base\n");
qphy->emu_phy_base = NULL;
}
}
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"tune2_efuse_addr");
if (res) {
qphy->tune2_efuse_reg = devm_ioremap_nocache(dev, res->start,
resource_size(res));
if (!IS_ERR_OR_NULL(qphy->tune2_efuse_reg)) {
ret = of_property_read_u32(dev->of_node,
"qcom,tune2-efuse-bit-pos",
&qphy->tune2_efuse_bit_pos);
if (!ret) {
ret = of_property_read_u32(dev->of_node,
"qcom,tune2-efuse-num-bits",
&qphy->tune2_efuse_num_of_bits);
}
if (ret) {
dev_err(dev, "DT Value for tune2 efuse is invalid.\n");
return -EINVAL;
}
}
}
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"ref_clk_addr");
if (res) {
qphy->ref_clk_base = devm_ioremap_nocache(dev,
res->start, resource_size(res));
if (IS_ERR(qphy->ref_clk_base))
dev_dbg(dev, "ref_clk_address is not available.\n");
}
qphy->ref_clk_src = devm_clk_get(dev, "ref_clk_src");
if (IS_ERR(qphy->ref_clk_src))
dev_dbg(dev, "clk get failed for ref_clk_src\n");
qphy->ref_clk = devm_clk_get(dev, "ref_clk");
if (IS_ERR(qphy->ref_clk))
dev_dbg(dev, "clk get failed for ref_clk\n");
else
clk_set_rate(qphy->ref_clk, 19200000);
qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb_clk");
if (IS_ERR(qphy->cfg_ahb_clk))
return PTR_ERR(qphy->cfg_ahb_clk);
qphy->phy_reset = devm_clk_get(dev, "phy_reset");
if (IS_ERR(qphy->phy_reset))
return PTR_ERR(qphy->phy_reset);
qphy->emulation = of_property_read_bool(dev->of_node,
"qcom,emulation");
of_get_property(dev->of_node, "qcom,emu-init-seq", &size);
if (size) {
qphy->emu_init_seq = devm_kzalloc(dev,
size, GFP_KERNEL);
if (qphy->emu_init_seq) {
qphy->emu_init_seq_len =
(size / sizeof(*qphy->emu_init_seq));
if (qphy->emu_init_seq_len % 2) {
dev_err(dev, "invalid emu_init_seq_len\n");
return -EINVAL;
}
of_property_read_u32_array(dev->of_node,
"qcom,qemu-init-seq",
qphy->emu_init_seq,
qphy->emu_init_seq_len);
} else {
dev_dbg(dev, "error allocating memory for emu_init_seq\n");
}
}
of_get_property(dev->of_node, "qcom,phy-pll-reset-seq", &size);
if (size) {
qphy->phy_pll_reset_seq = devm_kzalloc(dev,
size, GFP_KERNEL);
if (qphy->phy_pll_reset_seq) {
qphy->phy_pll_reset_seq_len =
(size / sizeof(*qphy->phy_pll_reset_seq));
if (qphy->phy_pll_reset_seq_len % 2) {
dev_err(dev, "invalid phy_pll_reset_seq_len\n");
return -EINVAL;
}
of_property_read_u32_array(dev->of_node,
"qcom,phy-pll-reset-seq",
qphy->phy_pll_reset_seq,
qphy->phy_pll_reset_seq_len);
} else {
dev_dbg(dev, "error allocating memory for phy_pll_reset_seq\n");
}
}
of_get_property(dev->of_node, "qcom,emu-dcm-reset-seq", &size);
if (size) {
qphy->emu_dcm_reset_seq = devm_kzalloc(dev,
size, GFP_KERNEL);
if (qphy->emu_dcm_reset_seq) {
qphy->emu_dcm_reset_seq_len =
(size / sizeof(*qphy->emu_dcm_reset_seq));
if (qphy->emu_dcm_reset_seq_len % 2) {
dev_err(dev, "invalid emu_dcm_reset_seq_len\n");
return -EINVAL;
}
of_property_read_u32_array(dev->of_node,
"qcom,emu-dcm-reset-seq",
qphy->emu_dcm_reset_seq,
qphy->emu_dcm_reset_seq_len);
} else {
dev_dbg(dev, "error allocating memory for emu_dcm_reset_seq\n");
}
}
of_get_property(dev->of_node, "qcom,qusb-phy-init-seq", &size);
if (size) {
qphy->qusb_phy_init_seq = devm_kzalloc(dev,
size, GFP_KERNEL);
if (qphy->qusb_phy_init_seq) {
qphy->init_seq_len =
(size / sizeof(*qphy->qusb_phy_init_seq));
if (qphy->init_seq_len % 2) {
dev_err(dev, "invalid init_seq_len\n");
return -EINVAL;
}
of_property_read_u32_array(dev->of_node,
"qcom,qusb-phy-init-seq",
qphy->qusb_phy_init_seq,
qphy->init_seq_len);
} else {
dev_err(dev, "error allocating memory for phy_init_seq\n");
}
}
qphy->ulpi_mode = false;
ret = of_property_read_string(dev->of_node, "phy_type", &phy_type);
if (!ret) {
if (!strcasecmp(phy_type, "ulpi"))
qphy->ulpi_mode = true;
} else {
dev_err(dev, "error reading phy_type property\n");
return ret;
}
hold_phy_reset = of_property_read_bool(dev->of_node, "qcom,hold-reset");
ret = of_property_read_u32_array(dev->of_node, "qcom,vdd-voltage-level",
(u32 *) qphy->vdd_levels,
ARRAY_SIZE(qphy->vdd_levels));
if (ret) {
dev_err(dev, "error reading qcom,vdd-voltage-level property\n");
return ret;
}
qphy->vdd = devm_regulator_get(dev, "vdd");
if (IS_ERR(qphy->vdd)) {
dev_err(dev, "unable to get vdd supply\n");
return PTR_ERR(qphy->vdd);
}
qphy->vdda33 = devm_regulator_get(dev, "vdda33");
if (IS_ERR(qphy->vdda33)) {
dev_err(dev, "unable to get vdda33 supply\n");
return PTR_ERR(qphy->vdda33);
}
qphy->vdda18 = devm_regulator_get(dev, "vdda18");
if (IS_ERR(qphy->vdda18)) {
dev_err(dev, "unable to get vdda18 supply\n");
return PTR_ERR(qphy->vdda18);
}
platform_set_drvdata(pdev, qphy);
qphy->phy.label = "msm-qusb-phy";
qphy->phy.init = qusb_phy_init;
qphy->phy.set_suspend = qusb_phy_set_suspend;
qphy->phy.shutdown = qusb_phy_shutdown;
qphy->phy.change_dpdm = qusb_phy_update_dpdm;
qphy->phy.type = USB_PHY_TYPE_USB2;
if (qphy->qscratch_base) {
qphy->phy.notify_connect = qusb_phy_notify_connect;
qphy->phy.notify_disconnect = qusb_phy_notify_disconnect;
}
#ifdef CONFIG_USB_HOST_NOTIFY
qphy->phy.set_mode = qusb_phy_set_mode;
#endif
/*
* On some platforms multiple QUSB PHYs are available. If QUSB PHY is
* not used, there is leakage current seen with QUSB PHY related voltage
* rail. Hence keep QUSB PHY into reset state explicitly here.
*/
if (hold_phy_reset)
clk_reset(qphy->phy_reset, CLK_RESET_ASSERT);
ret = usb_add_phy_dev(&qphy->phy);
return ret;
}
static int qusb_phy_remove(struct platform_device *pdev)
{
struct qusb_phy *qphy = platform_get_drvdata(pdev);
usb_remove_phy(&qphy->phy);
if (qphy->clocks_enabled) {
clk_disable_unprepare(qphy->cfg_ahb_clk);
clk_disable_unprepare(qphy->ref_clk);
clk_disable_unprepare(qphy->ref_clk_src);
qphy->clocks_enabled = false;
}
qusb_phy_enable_power(qphy, false, true);
return 0;
}
static const struct of_device_id qusb_phy_id_table[] = {
{ .compatible = "qcom,qusb2phy", },
{ },
};
MODULE_DEVICE_TABLE(of, qusb_phy_id_table);
static struct platform_driver qusb_phy_driver = {
.probe = qusb_phy_probe,
.remove = qusb_phy_remove,
.driver = {
.name = "msm-qusb-phy",
.of_match_table = of_match_ptr(qusb_phy_id_table),
},
};
module_platform_driver(qusb_phy_driver);
MODULE_DESCRIPTION("MSM QUSB2 PHY driver");
MODULE_LICENSE("GPL v2");
Reference in a new issue View git blame Copy permalink