More accurate unsafe motion calculation
* Safe and unsafe motion are calculated by dichotomy with a limited
number of steps. It's good for performance, but on long motions that
either collide near the beginning or near the end, the result can be
very imprecise.
* Now a factor 0.25 or 0.75 is used to converge faster when this case
happens, which allows longer motions to get more accurate collision
detection.
* Makes snap collision more precise, and helps with cases where diagonal collision on the border of a platform can lead to the character being stuck.
Additional improvements to move_and_slide:
* Handle slide canceling in move_and_collide with 0 velocity instead of
not applying it.
* Better handling of snap with custom logic to cancel sliding.
* Remove small jittering when using stop on slope, by canceling the
motion completely when the resulting motion is less than margin instead
of always projecting to the up direction (in both body motion and snap).
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
* Colors were imported as 16BPP (half float)
* Far most common use cases only require 8BPP
* If you need higher data precision, use a custom array, which are supported now.
**WARNING**: 3D Scenes imported in 4.0 no longer compatible with this new format. You need to re-import them (erase them from .godot/import)
* Removed entirely from RenderingServer.
* Replaced by ImmediateMesh resource.
* ImmediateMesh replaces ImmediateGeometry, but could use more optimization in the future.
* Sprite3D and AnimatedSprite3D work again, ported from Godot 3.x (though a lot of work was needed to adapt them to Godot 4).
* RootMotionView works again.
* Polygon3D editor works again.
New property disable_mode to set different behaviors:
Remove: remove from physics simulation
MakeStatic: change body mode to static (doesn't affect area and soft body)
KeepActive: do nothing
Extra change:
Handle disable/enable node state with specific notifications, in order
to differentiate global pause from disabled nodes.
* Functions to convert to/from degrees are all gone. Conversion is done by the editor.
* Use PROPERTY_HINT_ANGLE instead of PROPERTY_HINT_RANGE to edit radian angles in degrees.
* Added possibility to add suffixes to range properties, use "min,max[,step][,suffix:<something>]" example "0,100,1,suffix:m"
* In general, can add suffixes for EditorSpinSlider
Not covered by this PR, will have to be addressed by future ones:
* Ability to switch radians/degrees in the inspector for angle properties (if actually wanted).
* Animations previously made will most likely break, need to add a way to make old ones compatible.
* Only added a "px" suffix to 2D position and a "m" one to 3D position, someone needs to go through the rest of the engine and add all remaining suffixes.
* Likely also need to track down usage of EditorSpinSlider outside properties to add suffixes to it too.
* Editor 2D viewport now uses embedded subwindows (windows no longer pop up)
* Restored the ability to disable 3D on the 2D viewport (makes 3D not display on 2D when there is a camera on the scene)
Make sure the direction of the motion is preserved, unless the depth is
higher than the margin, which means the body needs depenetration in any
direction.
Also changed move_and_slide to avoid sliding on the first motion, in
order to avoid issues with unstable position on ground when jumping.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
* Deprecates GDNative in favor of a simpler, lower level interface.
* New extension system allows registering core engine classes.
* Simple header interface in gdnative_interace.h
The CylinderMesh generation code handles this special case and
avoids generating the top and bottom faces if their radius is equal
to 0. This improves performance by reducing the number of vertices
to draw.
If both values are set to 0, nothing will be visible but the mesh
generation will still succeed.
This also improves the CylinderMesh class documentation.
