3 options are available:
- Light and Sky (default)
- Light Only (new)
- Sky Only (equivalent to `use_in_sky_only = true`)
Co-authored by: clayjohn <claynjohn@gmail.com>
This can be used to fade lights and their shadows in the distance,
similar to Decal nodes. This can bring significant performance
improvements, especially for lights with shadows enabled and when
using higher-than-default shadow quality settings.
While lights can be smoothly faded out over distance, shadows are
currently "all or nothing" since per-light shadow color is no longer
customizable in the Vulkan renderer. This may result in noticeable
pop-in when leaving the shadow cutoff distance, but depending on the
scene, it may not always be that noticeable.
- Enable Read Sky Light to get proper outdoors lighting out of the box.
- Set bounce feedback to 0.5 by default to get a better quality result.
- Higher values may cause infinite feedback with bright surfaces.
- Increase the number of frames to converge to improve quality
at the cost of latency. Most scenes are fairly static after all.
- Use 75% Y scale by default as most scenes are not highly vertical.
- Reorder the Y scale enum to go from the lowest Y scale to the highest.
Also rename the "Disabled" setting to "100%" for clarity.
16-bit shadow atlases are already the default in the project settings,
but low-level methods used 24-bit shadows by default.
This makes low-level methods more consistent with the default project
settings to avoid accidental performance issues when users change
the shadow size at run-time.
This provides more flexibility between performance and quality
adjustments, especially when using SDFGI for small-scale levels
(which can be useful for procedurally generated scenes).
Applying overlay materials into multi-surface meshes currently
requires adding a next pass material to all the surfaces, which
might be cumbersome when the material is to be applied to a range
of different geometries. This also makes it not trivial to use
AnimationPlayer to control the material in case of visual effects.
The material_override property is not an option as it works
replacing the active material for the surfaces, not adding a new pass.
This commit adds the material_overlay property to GeometryInstance3D
(and therefore MeshInstance3D), having the same reach as
material_override (that is, all surfaces) but adding a new material
pass on top of the active materials, instead of replacing them.
This can be used to distinguish between integrated, dedicated, virtual
and software-emulated GPUs. This in turn can be used to automatically
adjust graphics settings, or warn users about features that may run
slowly on their hardware.
The built-in ALPHA in spatial shaders comes pre-set with a per-instance
transparency value. Multiply by it if you want to keep it.
The transparency value of any given GeometryInstance3D is affected by:
- Its new "transparency" property.
- Its own visiblity range when the new "visibility_range_fade_mode"
property is set to "Self".
- Its parent visibility range when the parent's fade mode is
set to "Dependencies".
The "Self" mode will fade-out the instance when reaching the visibility
range limits, while the "Dependencies" mode will fade-in its
dependencies.
Per-instance transparency is only implemented in the forward clustered
renderer, support for mobile should be added in the future.
Co-authored-by: reduz <reduzio@gmail.com>
This can be used to improve 3D shadow rendering quality at little
performance cost. Unlike the existing Hard setting which is limited
to variable shadow blur only, it works with both fixed blur and
variable blur.
This allows for finer control over 3D rendering resolution.
Supersampling can also be performed by setting a 3D rendering
resolution above 1.0, which is useful for offline rendering or
for very high-end GPUs.
This property was intended to provide a way to have SSAO or VoxelGI
ambient occlusion with a color other than black. However, it was
dropped during the Vulkan renderer development due to the performance
overhead it caused when the feature wasn't used.
* Fixed LODs for shadow meshes.
* Added a merging step before simplification. This helps with tesselated
meshes that were previously left untouched. The angle difference at
wich edges ar considered "hard" can be tweaked as an import setting.
* LODs will now start with the highest decimation possible and keep
doubling (approximately) the number of triangles from there. This
makes sure that very low triangle counts are included when possible.
* Given more weight to normal preservation.
* Modified MeshOptimizer to report distance-based error instead of
including attributes in the reported metrics.
* Added attribute transference between the original mesh and the
various LODs. Right now only normals are taken into account,
but it could be expanded to other attributes in the future.
In the `master` branch, 16× MSAA caused the entire system to freeze
on NVIDIA GPUs. This is likely caused by graphics drivers not actually
implementing 16× MSAA, but combining 8× MSAA with 2× SSAA instead.
On top of that, modern shader complexity makes 16× MSAA very difficult
to use while keeping a good framerate. 8× MSAA is hard enough to use
as it is.
* Shadow quality settings now specialization constant.
* Decal and light projector filters can be set.
* Changing those settings forces re-creation of the pipelines.
These changes should help improve performance related to shadow mapping, and allows improving performance by sacrificing decal and light projector quality.
* Keep track of when projector, softshadow or directional sofshadow were enabled.
* Enable them via specializaton constant where it makes sense.
* Re-implements soft shadows.
* Re-implements light projectors.
