This macro is not used so it's safe to remove it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Home routers based on SoCs like BCM53010 (AKA BCM4708) use flashes
which can be nicely partitioned with bcm47xxpart. Header bcm47xx_nvram.h
is not available on bcm53xx, so don't include it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Our code parsing "trx" header registers few partitions at once (in one
loop iteration). Add extra check in that place.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Up to now mtd-ram devices described in device trees were only accessible
if mtd-flash or mtd-rom were also configured at linux configuration
time, because MTD_PHYSMAP_OF was only available if (MTD_CFI ||
MTD_JEDECPROBE || MTD_ROM). Allow MTD_PHYSMAP_OF selection also
when only MTD_RAM is set.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some flashes can only be properly accessed when the ECC mode is
specified, so a way to describe such mode is required.
Together, the ECC strength and step size define the correction capability,
so that we say we will correct "{strength} bit errors per {size} bytes".
The interpretation of these parameters is implementation-defined, but they
often have ramifications on the formation, interpretation, and placement of
correction metadata on the flash. Not all implementations must support all
possible combinations. Implementations are encouraged to further define the
value(s) they support.
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds simple helpers to obtain the devicetree properties
that specify the ECC strength and ECC step size to use on a given
NAND controller.
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If jffs2_new_inode() succeeds, it returns with f->sem held, and the caller
is responsible for releasing the lock. If it fails, it still returns with
the lock held, but the caller won't release the lock, which will lead to
deadlock.
Fix it by releasing the lock in jffs2_new_inode() on error.
Signed-off-by: Wang Guoli <andy.wangguoli@huawei.com>
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wang Guoli <andy.wangguoli@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[Brian: not marked for stable; no one observed deadlock, and I don't
think it can happen here]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
@wait is a local variable, so if we don't remove it from the wait queue
list, later wake_up() may end up accessing invalid memory.
This was spotted by eyes.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no point in displaying the TS5500-specific driver entries if
TS5500 board support itself isn't enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR"
which is NULL and not a valid register.
Fixes: 8bff82cbc3 ('mtd: add nand support for w90p910 (v2)')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Check the chip->jedec_version, and print out the right information
for JEDEC compliant NAND.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the parsing code for the JEDEC compliant NAND.
Since we need the 0x40 as the column address, this patch also
makes the NAND_CMD_PARAM to use the 8-bit address only.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a helper to get the supported features for JEDEC compliant NAND.
Also add a macro JEDEC_FEATURE_16_BIT_BUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the jedec_version field, and add an anonymous union which
contains the nand_onfi_params and nand_jedec_params.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Create the nand_jedec_params{} and jedec_ecc_info{} according to
the JESD230A (Revision of JESD230, October 2012).
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 436d42c61c ("ARM: samsung: move platform_data definitions")
moved the files to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also add the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Check the return value from platform_get_irq() and propagate it in the case of
error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
"rc" is an error code here, no need to check it a second time.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PIO fall back is not an issue, so don't make this much noise.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ELM driver incorrectly reagard any non-zero return value from
pm_runtime_get_sync as an error, but it may return 1 if the device
was already active. Fix to only error when return value is negative.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
read_buf is called in place of write_buf in the
nand_write_page_raw_syndrome function.
Signed-off-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM and HAS_DMA to bypass build failures.
drivers/built-in.o: In function `flctl_probe':
drivers/mtd/nand/sh_flctl.c:1097: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `flctl_dma_fifo0_transfer':
drivers/mtd/nand/sh_flctl.c:368: undefined reference to `dma_map_single'
drivers/mtd/nand/sh_flctl.c:407: undefined reference to `dma_unmap_single'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use a repeated read_byte() instead of read_buf(), since for x16 buswidth
devices, we need to avoid the upper I/O[16:9] bits. See the following
commit for reference:
commit 05f7835975
Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Date: Thu Dec 5 22:22:04 2013 +0100
mtd: nand: don't use {read,write}_buf for 8-bit transfers
Now, I think that all barriers to probing ONFI on x16 devices are
removed, so remove the check from nand_flash_detect_onfi().
Tested on 8-bit ONFI NAND (Micron MT29F32G08CBADAWP).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
The NAND command helpers tend to automatically shift the column address
for x16 bus devices, since most commands expect a word address, not a
byte address. The Read ID command, however, expects an 8-bit address
(i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
0x20).
This fixes the column address for a few drivers which imitate the
nand_base defaults. Note that I don't touch sh_flctl.c, since it already
handles this problem slightly differently (note its comment "READID is
always performed using an 8-bit bus").
I have not tested this patch, as I only have x8 parts up for testing at
this point. Hopefully that can change soon...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
The datasheet does not tell us how to parse out the ID data,
so handle it as a full ID nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no reference to these two macros now.
Just remove them.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The patch converts the arrays to buffer pointers for nand_buffers{}.
The cafe_nand.c is the only NAND_OWN_BUFFERS user which allocates
nand_buffers{} itself.
This patch disables the DMA for nand_scan_ident, and restores the DMA
status after we finish the nand_scan_ident. This way, we can get page
size and OOB size and use them to allocate cafe->dmabuf.
Since the cafe_nand.c uses the NAND_ECC_HW_SYNDROME ECC mode, we do not
allocate the buffers for @ecccalc and @ecccode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Brian: dropped one incorrect hunk]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mutex_destroy added on each device in block2mtd_exit and add_device failure
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit b2a2a84d35 (mtd: phram: dot not crash when
built-in and passing boot param) claims to be "based on Ville Herva's similar
patch to block2mtd" (c4e7fb3137), but it has
missed the crucial point of the original path: all these "if(n)def MODULE".
It has broken the possibility to create several phram instances when phram is
compiled as module. The possibility to add instances via /sys writes to
/sys/module/phram/parameters/phram was also broken with mentioned patch.
Proposed patch takes the idea of original block2mtd patch to its full extent.
Assumption "This function is always called before 'init_phram()'" was also
incorrect, so removed the comment. This patch effectively reverts also
b11ec57fc6 (mtd: phram: fix section mismatch for
phram_setup).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[Brian: remove static assigment = 0]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We always put a NUL terminator one space past the end of the "vendor"
buffer. Walter Harms also pointed out that this should just use
kstrndup().
Fixes: 7d17c02a01 ('mtd: Add new SmartMedia/xD FTL')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Spansion s25fl256s1 and s25fl512s support Dual SPI transfers, hence set the
M25P80_DUAL_READ flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
