Commit graph

301191 commits

Author SHA1 Message Date
Ashok Nagarajan
57aac7c51c mac80211: Implement HT mixed protection mode
Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for
HT mesh STA in a MBSS. Three HT protection modes are supported for now:

non-HT mixed mode - is selected if any non-HT peers are present in our MBSS.
20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support
			HT and atleast one HT20 peer is present.
no-protection mode - is selected otherwise.

This is a limited implementation of 9.23.3.5, which only considers mesh peers
when determining the HT protection mode. Station's channel_type needs to be
maintained.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:57 -04:00
Ashok Nagarajan
431e315423 mac80211: Advertise HT protection mode in IEs
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:57 -04:00
Emmanuel Grumbach
ef9456a85d cfg80211: fix BSS comparison
Since the BSS table is organized in a RB tree, the BSSs need to be
comparable. This means that we must define a < and > operator to
the BSS object.
compare_ethr_addr isn't enough since it returns only a binary value.

Since Felix's

cfg80211: use compare_ether_addr on MAC addresses instead of memcmp

    Because of the constant size and guaranteed 16 bit alignment, the inline
    compare_ether_addr function is much cheaper than calling memcmp.

    Signed-off-by: Felix Fietkau <nbd@openwrt.org>
    Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BSS table is corrupted: rb_find_bss can't find the bss.
As a result BSSes are duplicated in the BSS table, and we get stuck
while probing an AP before associating (in STA mode).

Change-Id: I85928756f4328028230832c1565ece7f412f3843
CC: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:56 -04:00
Franky Lin
ba89bf1961 brcmfmac: add out of band interrupt support
Some sdio host controllers do not support real in band interrupt.
Software polling mode as a replacement is not fast enough for
high throughput and new features. Also some in band interrupts
do not support host wake up on embedded platform even when they
are real physical interrupts. Therefore out of band (oob)
interrupt mechanism is implemented for these scenarios.

To provide oob irq number and flags used for irq registration in
brcmfmac, a platform device contains irq resource must be
registered in board specific code.

Here is an example of platform device structure:
struct resource brcmf_sdio_res[] = {
	{
		.start	= GPIO_BRCMF_SDIO_OOB_NUM,
		.end	= GPIO_BRCMF_SDIO_OOB_NUM,
		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
	}
};
struct platform_device brcmf_sdio_device = {
	.name		= "brcmf_sdio_pd",
	.id		= -1,
	.num_resources	= ARRAY_SIZE(brcmf_sdio_res),
	.resource	= brcmf_sdio_res,
};

Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:55 -04:00
Franky Lin
e2f93cc321 brcmfmac: postpone interrupt register function
For out of band interrupt which is going to be introduced shortly,
the interrupt register function must be called after firmware is
downloaded. This patch moves it from brcmf_sdbrcm_probe to
brcmf_sdbrcm_bus_init.

Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:54 -04:00
Franky Lin
d9126e0c42 brcmfmac: check bus state for status
Bus state should be the correct flag for bus status. Use it instead
of result from previous function call for backplane clock switch.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:54 -04:00
Franky Lin
f0116fbfcb brcmfmac: stop releasing sdio host in irq handler
brcmf_sdbrcm_isr doesn't access to the dongle through SDIO bus.
Stop releasing and claiming host in irq handler to eliminate
any potential risk.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:53 -04:00
Ben Greear
3073a7c20c mac80211: Add more ethtools stats: survey, rates, etc
The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable.  This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:52 -04:00
Ben Greear
e352114fd6 mac80211: Framework to get wifi-driver stats via ethtool.
This adds hooks to call into the driver to get additional
stats for the ethtool API.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:51 -04:00
Ben Greear
b1ab79255c mac80211: Support getting sta_info stats via ethtool.
This lets ethtool print out stats related to stations
connected to the interface.  Does not yet get stats
from the underlying driver.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:50 -04:00
Ben Greear
d61992182e cfg80211: Add framework to support ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:49 -04:00
Wey-Yi Guy
35e7adaaf6 iwlwifi: use 6000G2B for 6030 device series
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:49 -04:00
Meenakshi Venkataraman
e377a4fc76 iwlwifi: use correct released ucode version
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:48 -04:00
Ben Hutchings
e19d8baf8c ipw2100: Fix order of device registration
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device.  The latter needs to be registered
first.

Compile-tested only.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:47 -04:00
Ben Hutchings
b4050790d0 ipw2200: Fix order of device registration
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device.  The latter needs to be registered
first.

Compile-tested only.

Reported-by: Cesare Leonardi <celeonar@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:47 -04:00
Anisse Astier
f2bd7f16e5 rt2x00: Add debugfs access for rfcsr register
RFCSR is only used in rt2800. For other chipsets, the debug struct
for rfcsr should be zeroed, which isn't be an issue, since the code
can now cope with that.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:46 -04:00
Anisse Astier
f2efd20fac rt2x00: debugfs support - allow a register to be empty
Allow a register to be unspecified, therefore not creating its debugfs
file entry.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:45 -04:00
Stanislav Yakovlev
7ed85b65ab net/wireless: ipw2200: Fix WARN_ON occurring in wiphy_register called by ipw_pci_probe
The problem was found by Stefan Lippers-Hollmann
http://marc.info/?l=linux-wireless&m=132720334512946&w=2

WARNING: at /tmp/buildd/linux-aptosid-3.2/debian/build/source_i386_none/net/wireless/core.c:562 wiphy_register+0x45/0x38d [cfg80211]()
Hardware name: TravelMate 290 \xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff
Modules linked in: ipw2200(+) iTCO_wdt libipw joydev drm snd_seq snd_timer snd_seq_device iTCO_vendor_support yenta_socket snd intel_agp i2c_i801 pcmcia_rsrc cfg80211 soundcore parport_pc psmouse parport rng_core snd_page_alloc serio_raw pcspkr i2c_algo_bit intel_gtt pcmcia_core evdev irda crc_ccitt rfkill lib80211 processor container ac battery shpchp pci_hotplug button ext4 mbcache jbd2 crc16 dm_mod sd_mod sr_mod crc_t10dif cdrom ata_generic pata_acpi ata_piix libata scsi_mod firewire_ohci firewire_core crc_itu_t 8139too 8139cp mii uhci_hcd ehci_hcd usbcore usb_common [last unloaded: scsi_wait_scan]
Pid: 328, comm: modprobe Not tainted 3.2-1.slh.4-aptosid-686 #1
Call Trace:
[<c012eaf4>] ? warn_slowpath_common+0x7c/0x8f
[<e0ff0b3e>] ? wiphy_register+0x45/0x38d [cfg80211]
[<e0ff0b3e>] ? wiphy_register+0x45/0x38d [cfg80211]
[<c012eb22>] ? warn_slowpath_null+0x1b/0x1f
[<e0ff0b3e>] ? wiphy_register+0x45/0x38d [cfg80211]
[<c01f89d7>] ? internal_create_group+0xf5/0xff
[<e0a2de1c>] ? ipw_pci_probe+0xa9a/0xbd0 [ipw2200]
[<c01519f4>] ? arch_local_irq_save+0xf/0x14
[<c0252986>] ? pci_device_probe+0x53/0x9a
[<c02c2820>] ? driver_probe_device+0x94/0x124
[<c0252871>] ? pci_match_id+0x15/0x34
[<c02c28f0>] ? __driver_attach+0x40/0x5b
[<c02c1d81>] ? bus_for_each_dev+0x37/0x60
[<c02c25aa>] ? driver_attach+0x17/0x1a
[<c02c28b0>] ? driver_probe_device+0x124/0x124
[<c02c22c4>] ? bus_add_driver+0x92/0x1d1
[<e099d000>] ? 0xe099cfff
[<c02c2cb8>] ? driver_register+0x7d/0xd4
[<c017cd50>] ? jump_label_module_notify+0xec/0x167
[<e099d000>] ? 0xe099cfff
[<c0253017>] ? __pci_register_driver+0x32/0x87
[<e099d000>] ? 0xe099cfff
[<e099d02e>] ? ipw_init+0x2e/0x72 [ipw2200]
[<c0101173>] ? do_one_initcall+0x7d/0x132
[<c0145016>] ? __blocking_notifier_call_chain+0x47/0x4f
[<c0154a73>] ? sys_init_module+0x13a4/0x159c
[<c03a639f>] ? sysenter_do_call+0x12/0x28

This warning appears only if we apply Ben Hutchings' fix
http://marc.info/?l=linux-wireless&m=132720195012653&w=2
for the bug reported by Cesare Leonardi
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=656813
with cfg80211 warning during device registration
("cfg80211: failed to add phy80211 symlink to netdev!").

We separate device bring up and registration with network stack
to avoid the problem.

After that Ben Hutchings' fix can be applied to fix the bug.

Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:44 -04:00
Wey-Yi Guy
4fb2f7f3b7 iwlwifi: remove the iwl_shared reference
Change-Id: I10e42e0cc7dd91047f093ea2c5a55d65c004ada6
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-on: http://git-mwg.jer.intel.com/gerrit/1939
Tested-by: Jenkins
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2012-05-08 21:53:44 -04:00
Wey-Yi Guy
07d3c15acc iwlwifi: modify #ifdef to avoid sparse complain
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 21:53:43 -04:00
Thomas Pedersen
c7d258288f mac80211: don't transmit 40MHz frames to 20MHz peer
If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:42 -04:00
Thomas Pedersen
e87278e730 mac80211: insert mesh peer after init
Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.

This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:42 -04:00
Amitkumar Karwar
2e4c14a558 mwifiex: fix static checker warnings
"oui_type" in structure "ieee_types_vendor_header" is not used separately,
so include it in "oui" array. Now complete oui will be compared fixing
following warnings.

drivers/net/wireless/mwifiex/sta_ioctl.c:1410 mwifiex_set_gen_ie_helper()
        error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/sta_ioctl.c:1435 mwifiex_set_gen_ie_helper()
        error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1177 mwifiex_update_bss_desc_with_ie()
        error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1185 mwifiex_update_bss_desc_with_ie()
        error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:41 -04:00
Rajkumar Manoharan
91a0099c19 mac80211: fix rate control update on 2040 bss change
The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:39 -04:00
WarheadsSE
98e6b9df53 mwifiex: add support for SD8786 sdio
modified:   drivers/net/wireless/mwifiex/Kconfig
	- notate additional chipset
	modified:   drivers/net/wireless/mwifiex/sdio.c
	- add definition of id (0x9116)
	- add to switch for firmware load
	- add MODULE_FIRMWARE
	modified:   drivers/net/wireless/mwifiex/sdio.h
	- add definition of default firmware name

Signed-off-by: Jason Plum <max@warheads.net>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 20:56:10 -04:00
Dan Carpenter
62c50543ce wireless: at76c50x: allocating too much data
This is a cut and paste mistake, sizeof(struct mib_local) was intended
instead of sizeof(struct mib_phy).  The call to at76_get_mib() uses
sizeof(struct mib_local) correctly, although I changed that to
sizeof(*m) for style reasons after discussion with some of the wireless
maintainers.

The current code works fine because mib_phy structs are larger than
mib_local structs.  But we may as well clean it up.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 20:56:10 -04:00
Emmanuel Grumbach
8b5bed90a5 iwlwifi: don't init trans->reg_lock from the op_mode
This doesn't make any sense. Init it from the transport instead.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:09 -04:00
Stanislaw Gruszka
f6b1154678 iwlwifi: add option to disable 5GHz band
There are various problems happened on 5GHz band not observed on
2.4 GHz (microcode errors, queue stuck, etc... ) . Also roaming
between 5GHz AP and 2GHz does not work very well. To workaround
the problems add option to disable 5GHz support. This will help
on environments where APs are dual-band, and devices will not try
to associate on band where issues happen.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:09 -04:00
Emmanuel Grumbach
c15797e6af iwlwifi: use IWL_* instead of dev_printk when possible
Also remove a debug print when allocation error occurred.
The kernel will complain anyway.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:09 -04:00
Wey-Yi Guy
4d5ba61ca3 iwlwifi: add loose coex lut
Add the Loose coex LUT and will use later for better bt coex tpt

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:09 -04:00
Wey-Yi Guy
9dc4ca92aa iwlwifi: change kill mask based on reduce power state
In bt coex, consider reduce tx power as part of ack/cts kill mask

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:09 -04:00
Wey-Yi Guy
310fbfd985 iwlwifi: send reduce tx power info in command
Add the reduce tx power information in bt coex host command

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:08 -04:00
Wey-Yi Guy
7edae18490 iwlwifi: small define change
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:08 -04:00
Wey-Yi Guy
4aa79d91f0 iwlwifi: add reduced tx power threshold define
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:08 -04:00
Wey-Yi Guy
354ce4a4ca iwlwifi: add checking for the condition to reduce tx power
When bluetooth coex is active and certain condition matched,
driver need to decide should the tx power been reduce or not.
Adding the logic to manage it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:08 -04:00
Wey-Yi Guy
9a00be04e6 iwlwifi: add BT reduced tx power flag
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:08 -04:00
Wey-Yi Guy
a70453b5d0 iwlwifi: remove unused macros
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-05-08 20:56:08 -04:00
Luis R. Rodriguez
138a53ef49 libertas: include sched.h on firmware.c
Do not assume we have our subsystem including this for us,
at least for older kernels this is not true. Lets just be
explicit about this requirement for the usage of wake_up().

Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 20:56:07 -04:00
David S. Miller
9bb862beb6 Merge branch 'master' of git://1984.lsi.us.es/net-next 2012-05-08 14:40:21 -04:00
Pablo Neira Ayuso
d16cf20e2f netfilter: remove ip_queue support
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.

This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.

Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-05-08 20:25:42 +02:00
Pablo Neira Ayuso
6714cf5465 netfilter: nf_conntrack: fix explicit helper attachment and NAT
Explicit helper attachment via the CT target is broken with NAT
if non-standard ports are used. This problem was hidden behind
the automatic helper assignment routine. Thus, it becomes more
noticeable now that we can disable the automatic helper assignment
with Eric Leblond's:

9e8ac5a netfilter: nf_ct_helper: allow to disable automatic helper assignment

Basically, nf_conntrack_alter_reply asks for looking up the helper
up if NAT is enabled. Unfortunately, we don't have the conntrack
template at that point anymore.

Since we don't want to rely on the automatic helper assignment,
we can skip the second look-up and stick to the helper that was
attached by iptables. With the CT target, the user is in full
control of helper attachment, thus, the policy is to trust what
the user explicitly configures via iptables (no automatic magic
anymore).

Interestingly, this bug was hidden by the automatic helper look-up
code. But it can be easily trigger if you attach the helper in
a non-standard port, eg.

iptables -I PREROUTING -t raw -p tcp --dport 8888 \
	-j CT --helper ftp

And you disabled the automatic helper assignment.

I added the IPS_HELPER_BIT that allows us to differenciate between
a helper that has been explicitly attached and those that have been
automatically assigned. I didn't come up with a better solution
(having backward compatibility in mind).

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-05-08 19:44:42 +02:00
Kelvie Wong
9768e1ace4 netfilter: nf_ct_expect: partially implement ctnetlink_change_expect
This refreshes the "timeout" attribute in existing expectations if one is
given.

The use case for this would be for userspace helpers to extend the lifetime
of the expectation when requested, as this is not possible right now
without deleting/recreating the expectation.

I use this specifically for forwarding DCERPC traffic through:

DCERPC has a port mapper daemon that chooses a (seemingly) random port for
future traffic to go to. We expect this traffic (with a reasonable
timeout), but sometimes the port mapper will tell the client to continue
using the same port. This allows us to extend the expectation accordingly.

Signed-off-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-05-08 19:40:59 +02:00
Hans Schillstrom
6d8ebc8a27 net: export sysctl_[r|w]mem_max symbols needed by ip_vs_sync
To build ip_vs as a module sysctl_rmem_max and sysctl_wmem_max
needs to be exported.

The dependency was added by "ipvs: wakeup master thread" patch.

Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-05-08 19:40:56 +02:00
H Hartley Sweeten
068d522067 ipvs: ip_vs_proto: local functions should not be exposed globally
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.

This quiets the sparse warnings:

warning: symbol '__ipvs_proto_data_get' was not declared. Should it be static?

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:40:54 +02:00
H Hartley Sweeten
d5cce20874 ipvs: ip_vs_ftp: local functions should not be exposed globally
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.

This quiets the sparse warnings:

warning: symbol 'ip_vs_ftp_init' was not declared. Should it be static?

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:40:52 +02:00
Pablo Neira Ayuso
6b324dbfc3 ipvs: optimize the use of flags in ip_vs_bind_dest
cp->flags is marked volatile but ip_vs_bind_dest
can safely modify the flags, so save some CPU cycles by
using temp variable.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:40:49 +02:00
Pablo Neira Ayuso
f73181c828 ipvs: add support for sync threads
Allow master and backup servers to use many threads
for sync traffic. Add sysctl var "sync_ports" to define the
number of threads. Every thread will use single UDP port,
thread 0 will use the default port 8848 while last thread
will use port 8848+sync_ports-1.

	The sync traffic for connections is scheduled to many
master threads based on the cp address but one connection is
always assigned to same thread to avoid reordering of the
sync messages.

	Remove ip_vs_sync_switch_mode because this check
for sync mode change is still risky. Instead, check for mode
change under sync_buff_lock.

	Make sure the backup socks do not block on reading.

Special thanks to Aleksey Chudov for helping in all tests.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:40:33 +02:00
Julian Anastasov
749c42b620 ipvs: reduce sync rate with time thresholds
Add two new sysctl vars to control the sync rate with the
main idea to reduce the rate for connection templates because
currently it depends on the packet rate for controlled connections.
This mechanism should be useful also for normal connections
with high traffic.

sync_refresh_period: in seconds, difference in reported connection
	timer that triggers new sync message. It can be used to
	avoid sync messages for the specified period (or half of
	the connection timeout if it is lower) if connection state
	is not changed from last sync.

sync_retries: integer, 0..3, defines sync retries with period of
	sync_refresh_period/8. Useful to protect against loss of
	sync messages.

	Allow sysctl_sync_threshold to be used with
sysctl_sync_period=0, so that only single sync message is sent
if sync_refresh_period is also 0.

	Add new field "sync_endtime" in connection structure to
hold the reported time when connection expires. The 2 lowest
bits will represent the retry count.

	As the sysctl_sync_period now can be 0 use ACCESS_ONCE to
avoid division by zero.

	Special thanks to Aleksey Chudov for being patient with me,
for his extensive reports and helping in all tests.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:40:10 +02:00
Pablo Neira Ayuso
1c003b1580 ipvs: wakeup master thread
High rate of sync messages in master can lead to
overflowing the socket buffer and dropping the messages.
Fixed sleep of 1 second without wakeup events is not suitable
for loaded masters,

	Use delayed_work to schedule sending for queued messages
and limit the delay to IPVS_SYNC_SEND_DELAY (20ms). This will
reduce the rate of wakeups but to avoid sending long bursts we
wakeup the master thread after IPVS_SYNC_WAKEUP_RATE (8) messages.

	Add hard limit for the queued messages before sending
by using "sync_qlen_max" sysctl var. It defaults to 1/32 of
the memory pages but actually represents number of messages.
It will protect us from allocating large parts of memory
when the sending rate is lower than the queuing rate.

	As suggested by Pablo, add new sysctl var
"sync_sock_size" to configure the SNDBUF (master) or
RCVBUF (slave) socket limit. Default value is 0 (preserve
system defaults).

	Change the master thread to detect and block on
SNDBUF overflow, so that we do not drop messages when
the socket limit is low but the sync_qlen_max limit is
not reached. On ENOBUFS or other errors just drop the
messages.

	Change master thread to enter TASK_INTERRUPTIBLE
state early, so that we do not miss wakeups due to messages or
kthread_should_stop event.

Thanks to Pablo Neira Ayuso for his valuable feedback!

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:39:53 +02:00
Julian Anastasov
cdcc5e905d ipvs: always update some of the flags bits in backup
As the goal is to mirror the inactconns/activeconns
counters in the backup server, make sure the cp->flags are
updated even if cp is still not bound to dest. If cp->flags
are not updated ip_vs_bind_dest will rely only on the initial
flags when updating the counters. To avoid mistakes and
complicated checks for protocol state rely only on the
IP_VS_CONN_F_INACTIVE bit when updating the counters.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-05-08 19:38:31 +02:00