Enable reliable use of Message-Signaled Interrupts (MSI) in sata_mv
by masking further chip interrupts within the main interrupt handler.
Based upon a suggestion by Grant Grundler.
MSI is working reliably in all of my test systems here now.
Signed-off-by: Mark Lord <mlord@pobox.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:
mv_set_main_irq_mask(host, ~0, 0);
The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.
The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.
However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause. This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports. With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned. It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset. SWNCQ is
modified to inherit from this new type.
This fixes hotplug regression reported in kernel bz#12351.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
nv_nf2_hardreset() will be used by other flavors too. Rename it to
nv_noclassify_hardreset().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0. This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.
This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Use consistent types for ehca_plpar_hcall9()
IB/ehca: Fix printk format warnings from u64 type change
IPoIB: Do not print error messages for multicast join retries
IB/mlx4: Fix memory ordering problem when posting LSO sends
mlx4_core: Fix min() warning
IPoIB: Fix deadlock between ipoib_open() and child interface create
IPoIB: Fix hang in napi_disable() if P_Key is never found
Reading 0 bytes from /sys/devices/platform/dell_rbu/image_type or
/sys/devices/platform/dell_rbu/packet_size by an ordinary user causes an
oops.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A pointer to wm8400_regulator_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ehca_plpar_hcall9() takes an unsigned long array, so make all callers
pass that in. This fixes warnings introduced by commit fe333321
("powerpc: Change u64/s64 to a long long integer type"), which changed
u64 from unsigned long to unsigned long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit fe333321 ("powerpc: Change u64/s64 to a long long integer
type") changed u64 from unsigned long to unsigned long long, which
means that printk formats for printing u64 values should use "ll"
instead of "l" to avoid warnings. Fix all the places affected by this
in ehca.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current work request posting code writes the LSO segment before
writing any data segments. This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments. When the HCA processes this work request, a local
protection error may result.
Fix this by saving the LSO header size field off and writing it only
after all data segments are written. This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI PCI hotplug: harden against panic regression
ACPI: rename main.c to sleep.c
dell-laptop: move to drivers/platform/x86/ from drivers/misc/
eeepc-laptop: enable Bluetooth ACPI details
ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
kprobes: check CONFIG_FREEZER instead of CONFIG_PM
PM: Fix freezer compilation if PM_SLEEP is unset
thermal fixup for broken BIOS which has invalid trip points.
ACPI: EC: Don't trust ECDT tables from ASUS
ACPI: EC: Limit workaround for ASUS notebooks even more
ACPI: thinkpad-acpi: bump up version to 0.22
ACPI: thinkpad-acpi: handle HKEY event 6030
ACPI: thinkpad-acpi: clean-up fan subdriver quirk
ACPI: thinkpad-acpi: start the event hunt season
ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms
ACPI: thinkpad-acpi: clean up hotkey_notify()
ACPI: thinkpad-acpi: use killable instead of interruptible mutexes
ACPI: thinkpad-acpi: add UWB radio support
ACPI: thinkpad-acpi: preserve radio state across shutdown
ACPI: thinkpad-acpi: resume with radios disabled
...
ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136
Rather than reverting the entire commit that causes the crash:
e8c331e963
"PCI hotplug: introduce functions for ACPI slot detection"
simply harden against it while the changes to
the hotplug code on this particularl machine are understood.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Although rfkill support for the EEE bluetooth device has been added to
2.6.28-rc the appropriate ACPI accessor definitions were not added, so
the support was non functional. The patch below adds the get and set
accessors and has been verified to work on an EEE 901.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec;
that bit has nothing to do with status bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Check CONFIG_FREEZER instead of CONFIG_PM because kprobe booster
depends on freeze_processes() and thaw_processes() when CONFIG_PREEMPT=y.
This fixes a linkage error which occurs when CONFIG_PREEMPT=y, CONFIG_PM=y
and CONFIG_FREEZER=n.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
Freezer fails to compile if with the following configuration
settings:
CONFIG_CGROUPS=y
CONFIG_CGROUP_FREEZER=y
CONFIG_MODULES=y
CONFIG_FREEZER=y
CONFIG_PM=y
CONFIG_PM_SLEEP=n
Fix this by making process.o compilation depend on CONFIG_FREEZER.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.
"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix ioctl arg size (userland incompatible change!)
Btrfs: Clear the device->running_pending flag before bailing on congestion
The structure used to send device in btrfs ioctl calls was not
properly aligned, and so 32 bit ioctls would not work properly on
64 bit kernels.
We could fix this with compat ioctls, but we're just one byte away
and it doesn't make sense at this stage to carry about the compat ioctls
forever at this stage in the project.
This patch brings the ioctl arg up to an evenly aligned 4k.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs maintains a queue of async bio submissions so the checksumming
threads don't have to wait on get_request_wait. In order to avoid
extra wakeups, this code has a running_pending flag that is used
to tell new submissions they don't need to wake the thread.
When the threads notice congestion on a single device, they
may decide to requeue the job and move on to other devices. This
makes sure the running_pending flag is cleared before the
job is requeued.
It should help avoid IO stalls by making sure the task is woken up
when new submissions come in.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
serial: Add 16850 uart type support to OF uart driver
hvc_console: Remove tty->low_latency
powerpc: Get the number of SLBs from "slb-size" property
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3
powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block
powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc
powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments
powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
powerpc/ps3: The lv1_ routines have u64 parameters
powerpc/ps3: Use dma_addr_t down through the stack
powerpc/ps3: set_dabr() takes an unsigned long
powerpc: Cleanup from l64 to ll64 change drivers/scsi
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl: Return non-zero on error in probe()
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
libata: New driver for OCTEON SOC Compact Flash interface (v7).
libata: Add another column to the ata_timing table.
sata_via: Add VT8261 support
pata_atiixp: update port enabledness test handling
[libata] get-identity ioctl: Fix use of invalid memory pointer
This reverts commit 98e6e286d7, as Yinghai
Lu reports that it breaks kexec with at least the e1000 and e1000e
drivers. The reason is that the shutdown sequence puts the hardware
into D3 sleep, and the commit causes us to claim that it then is in D0
(running) state just because we don't understand the PM capabilities.
Which then later makes "pci_set_power_state()" not do anything, and the
device never wakes up properly and just returns 0xff to everything.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: From: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
while I was looking over kernel sources I've found this small bug.
Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
