Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.
Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().
Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure, once initialized, never changes.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take
effect on 5709.
- Increase the default rx-frames to reduce interrupt count.
- Decrease the default rx-frames-irq and tx-frames-irq to catch more events
during NAPI poll.
All these will reduce interrupts without affecting latency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report this counter to ethtool -S and include it in netstat.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unable to allocate memory for new MTU or new ring size, we need
to close the device to prevent it from crashing.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this check to bnx2_netif_stop() and bnx2_vlan_rx_register() to
prevent bus lockups on some systems when the chip is in low power state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case IRQs are shared, we will not mistakenly start processing
the ring based on old status block indices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mwl8k_priv->fw_lock spinlock doesn't actually protect
against multiple commands being submitted at once, as it is not kept
held over the entire firmware command submission. And since waiting
for command completion sleeps, we can't use a spinlock anyway.
To fix mwl8k firmware command serialisation properly, we have the
following requirements:
- Some commands require that the packet transmit path is idle when
the command is issued. (For simplicity, we'll just quiesce the
transmit path for every command.)
- There are certain sequences of commands that need to be issued to
the hardware sequentially, with no other intervening commands.
This leads to an implementation of a "firmware lock" as a mutex that
can be taken recursively, and which is taken by both the low-level
command submission function (mwl8k_post_cmd) as well as any users of
that function that require issuing of an atomic sequence of commands,
and quiesces the transmit path whenever it's taken.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete most of the mwl8k_work_struct fields and options, since most
of them are unused or never changed from their defaults:
- We always use priv->config_wq, so delete the wqueue argument from
mwl8k_queue_work().
- MWL8K_WQ_SPIN and MWL8K_WQ_POST_REQUEST are never used, as all
callers sleep for request completion, so sleep unconditionally.
- MWL8K_WQ_FREE_WORKSTRUCT is never used.
- MWL8K_WQ_TX_WAIT_EMPTY is always set, so assume it unconditionally.
- timeout_ms/txwait_attempts/tx_timeout_ms are never changed from
their defaults, so just hardcode these in the workqueue worker.
- step is never used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various mwl8k_txq_xmit changes:
- Extract the QoS field before adding the DMA header.
- Only write to tx->status once, and only after all the other
descriptor fields have been set.
- Do all tx state manipulation under the tx spinlock.
- Remove the priv->inconfig check, as all transmit queues will
be frozen during config cycles, so we won't ever be asked to
transmit if a config cycle is running.
- Remove some more dead code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use MWL8K_TX_QUEUES instead of a hardcoded "4" in a couple of places.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since firmware load commands don't generate 'command done' interrupts
like normal commands do, polling for command done interrupts just
unnecessarily slows down the firmware load process. Removing this bit
of code speeds up loading a typical firmware image from 840 msec to
180 msec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding and removing the DMA header that the mwl8k hardware requires
on tx and provides on rx can never fail, since we are guaranteed to
have enough headroom on the tx path to expand the packet, and we only
ever shrink the packet on the rx path. (And on both paths we are
guaranteed to be the only user of the skb we are handling.)
This allows removing all of the skb clone handling in the tx and tx
reclaim paths, and eliminates error checks in both the tx and rx
paths, simplifying the code a bit more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check for NL80211_IFTYPE_MONITOR in
->add_interface(), as this function is never called for monitor
interfaces. Also, there is no need to advertise this bit in our
wiphy's ->interface_modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k_configure_filter() passes pointers to total_flags and the
multicast address list to a workqueue function, while there is no
guarantee that those pointers will still be valid by the time the
workqueue function runs.
Solve this by passing total_flags by value, and by passing an
already built multicast address setup command packet to the workqueue
function so that we don't have to look at the multicast address list
itself outside of mwl8k_configure_filter().
Also, since ->configure_filter() can sleep now, wait synchronously
for the worker to finish.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing a flag bitmask to mwl8k_cmd_802_11_radio_control,
pass the 'enable' and 'force' arguments as separate parameters, and
introduce wrappers for the common cases of enabling and disabling
without forcing.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other than ns_avgbrssi (Average beacon rssi) no data of
ath9k_node_stats is being used anywhere. Nuke this structure
and move its only useful member to ar5416Anistate. Also cleanup
this redundant data in ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the beacon rssi that LPF gives is divided and rounded
up by ATH_RSSI_EP_MULTIPLIER twice. This will leave the incorrect rssi
in ANI. Having correct rssi in ANI fixes the connection stability at
< 30dB rssi range. This patch removes the unncessary computation of average
rssi over already valid average rssi. Also removes the redundant macros to
find average rssi.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This add hardware tkip for b43.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: fix alignment problem in scan request"
introduced a bug into the error path, because now
we allocate the entire scan request and not just
the channel list (the channel list is allocated
together with the scan request) -- on errors we
thus also need to free the entire scan request.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry has started re-checking all current routines against a new
version of the Broadcom MIPS driver. This patch implements the first
round of changes he documented on the specs wiki.
Also remove a few FIXMEs regarding missing initial values for variables
with dynamic initial values where reading the values has been implemented.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of connection failure, the bssid info is not a must have.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
