HP C2502 cards (based on 53C400A chips) use different magic numbers for
software-based I/O address configuration than other cards.
The configuration is also extended to allow setting the IRQ.
Move the configuration to a new function magic_configure() and move
magic the magic numbers into an array. Add new magic numbers for these
HP cards and hp_c2502 module parameter to use them, e.g.:
modprobe g_NCR5380 ncr_irq=7 ncr_addr=0x280 hp_c2502=1
Tested with HP C2502 and DTCT-436P.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The check for 53C80 registers accessibility was commented out because
it was broken (inverted). Fix and enable it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add I/O register mapping for DTC chips and enable PDMA mode.
These chips have 16-bit wide HOST BUFFER register and it must be read
by 16-bit accesses (we lose data otherwise).
Large PIO transfers crash at least the DTCT-436P chip (all reads result
in 0xFF) so this patch actually makes it work.
The chip also crashes when we bang on the C400 host status register too
heavily after PDMA write - a small udelay is needed.
Tested on DTCT-436P and verified that it does not break 53C400A.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add I/O register mapping for NCR53C400A and enable PDMA mode to
improve performance and fix non-working IRQ.
Tested with HP C2502 (and user-space enabler).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert compile-time C400_ register mapping to runtime mapping.
This removes the weird negative register offsets and allows adding
additional mappings.
While at it, convert read/write loops into insb/outsb.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pseudo-DMA (PDMA) has been broken for ages, resulting in hangs on
53C400-based cards.
According to 53C400 datasheet, PDMA transfer length must be a multiple
of 128. Check if that's true and use PIO if it's not.
This makes PDMA work on 53C400 (Canon FG2-5202).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the past, atari_NCR5380.c was overlooked by those working on NCR5380.c
and this caused needless divergence. All of the changes in this patch were
taken from NCR5380.c.
This removes some unimportant discrepancies between the two core driver
forks so that 'diff' can be used to reveal the important ones, to
facilitate reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the past, NCR5380.c was overlooked by those working on atari_NCR5380.c
and this caused needless divergence. All of the changes in this patch were
taken from atari_NCR5380.c.
This removes some unimportant discrepancies between the two core driver
forks so that 'diff' can be used to reveal the important ones, to
facilitate reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hanging indentation was a poor choice for the text inside comments. It
has been used in the wrong places and done badly elsewhere. There is
little consistency within any file. One fork of the core driver uses
tabs for this indentation while the other uses spaces. Better to use
flush-left alignment throughout.
This patch is the result of the following substitution. It replaces tabs
and spaces at the start of a comment line with a single space.
perl -i -pe 's,^(\t*[/ ]\*)[ \t]+,$1 ,' drivers/scsi/{atari_,}NCR5380.c
This removes some unimportant discrepancies between the two core driver
forks so that the important ones become obvious, to facilitate
reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is the result of the following substitution. It removes any
tabs and spaces at the end of a line.
perl -i -pe 's,[\t ]+$,,' drivers/scsi/{atari_,}NCR5380.c
This removes some unimportant discrepancies between the two core driver
forks so that the important ones become obvious, to facilitate
reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CVS revision log is not nearly as useful as the history/history.git
repo, so remove it. Roman's commentary at the top of his driver repeats
the same information elsewhere in the file so remove it. Also remove
some other redundant or obsolete comments.
Both the driver and the datasheets confusingly refer to a DMA access
for a SCSI WRITE command as a "DMA write". Similarly a SCSI READ command
is called a "DMA read". This is the opposite of the usual convention.
Thankfully, the chip documentation and driver code also use "DMA send" and
"DMA receive", so adopt this terminology.
This removes some unimportant discrepancies between the two core driver
forks so that 'diff' can be used to reveal the important ones, to
facilitate reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because of the rudimentary design of the chip, it is necessary to poll the
SCSI bus signals during PIO and this tends to hog the CPU. The driver will
accept new commands while others execute, and this causes a soft lockup
because the workqueue item will not terminate until the issue queue is
emptied.
When exercising dmx3191d using sequential IO from dd, the driver is sent
512 KiB WRITE commands and 128 KiB READs. For a PIO transfer, the rate is
is only about 300 KiB/s, so these are long-running commands. And although
PDMA may run at several MiB/s, interrupts are disabled for the duration
of the transfer.
Fix the unresponsiveness and soft lockup issues by calling cond_resched()
after each command is completed and by limiting max_sectors for drivers
that don't implement real DMA.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This refactoring removes two global Scsi_Host pointers. This
improves consistency with other ncr5380 drivers. Adopting the same
conventions as the other drivers makes them easier to read.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Keep the two core driver forks in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the HOSTNO macro that is peculiar to atari_NCR5380.c and
contributes to the problem of divergence of the NCR5380 core drivers.
Keep NCR5380.c in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380.c lacks a sane eh_bus_reset_handler. The atari_NCR5380.c code is
much better but it should not throw out the issue queue (that would be
a host reset) and it neglects to set the result code for commands that it
throws out. Fix these bugs and keep the two core drivers in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During arbitration and selection, the relevant command is invisible to
exception handlers and can be found only in a pointer on the stack of a
different thread.
When eh_abort_handler can't find a given command, it can't decide whether
that command was completed already or is still in arbitration or selection
phase. But it must return either SUCCESS (e.g. command completed earlier)
or FAILED (could not abort the nexus, try bus reset).
The solution is to make sure all commands belonging to the LLD are always
visible to exception handlers. Add another scsi_cmnd pointer to the
hostdata struct to track the command in arbitration or selection phase.
Replace 'retain_dma_irq' with the new 'selecting' pointer, to bring
atari_NCR5380.c into line with NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a new eh_abort_handler implementation. This one attempts to
follow all of the rules relating to EH handlers. There is still a known
bug: during selection, a command becomes invisible to the EH handlers
because it only appears in a pointer on the stack of a different thread.
This bug is addressed in a subsequent patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_information_transfer() may re-queue a command for autosense,
after calling scsi_eh_prep_cmnd(). This creates several possibilities:
1. Reselection may intervene before the re-queued command gets processed.
If the reconnected command then undergoes autosense, this causes the
scsi_eh_save data from the previous command to be overwritten.
2. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
a new REQUEST SENSE command may arrive. This would be queued ahead
of any command already undergoing autosense, which means the
scsi_eh_save data might be restored to the wrong command.
3. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
eh_abort_handler() may abort the command. But the scsi_eh_save data is
not discarded, which means the scsi_eh_save data might be incorrectly
restored to the next REQUEST SENSE command issued.
This patch adds a new autosense list so that commands that are re-queued
because of a CHECK CONDITION result can be kept apart from the REQUEST
SENSE commands that arrive via queuecommand.
This patch also adds a function dedicated to dequeueing and preparing the
next command for processing. By refactoring the main loop in this way,
scsi_eh_save takes place when an autosense command is dequeued rather
than when re-queued.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement a 'complete_cmd' function to complete commands. This is needed
by the following patch; the new function provides a site for the logic
needed to correctly handle REQUEST SENSE commands.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NCR5380 drivers have a home-spun linked list implementation for
scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt
the standard list_head data structure and list operations instead. Remove
the eh_abort_handler rather than convert it. Doing the conversion would
only be churn because the existing EH handlers don't work and get replaced
in a subsequent patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hostdata struct is now protected by a spin lock so the volatile
qualifiers are redundant. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Printing command pointers can be useful when debugging queues. Other than
that, the LIST and REMOVE macros are just clutter. These macros are
redundant now that NDEBUG_QUEUES causes pointers to be printed, so remove
them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print the command pointers in the log messages for debugging queue data
structures. The LIST and REMOVE macros can then be removed.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of the shost_priv() helper. Remove HOSTDATA and SETUP_HOSTDATA
macros because they harm readability.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace all H_NO and some HOSTNO macros (both peculiar to atari_NCR5380.c)
with a new dsprintk macro that's more useful and more consistent. The new
macro avoids a lot of boilerplate in new code in subsequent patches. Keep
NCR5380.c in sync. Remaining HOSTNO macros are removed as side-effects
of subsequent patches.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some NCR5380 hosts offer a .show_info method to access the contents of
the various command list data structures from a procfs file. When NDEBUG
is set, the same information is sent to the console during EH.
The two core drivers, atari_NCR5380.c and NCR5380.c differ here. Because
it is just for debugging, the easiest way to fix the discrepancy is
simply remove this code.
The only remaining users of NCR5380_show_info() and NCR5380_write_info()
are drivers that define PSEUDO_DMA. The others have no use for the
.show_info method, so don't initialize it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380.c presently uses the instance->host_lock spin lock. Convert this
to a new spin lock that protects the NCR5380_hostdata struct.
atari_NCR5380.c previously used local_irq_save/restore() rather than a
spin lock. Convert this to hostdata->lock in irq mode. For SMP platforms,
the interrupt handler now also acquires the spin lock.
This brings all locking in the two core drivers into agreement.
Adding this locking also means that a bunch of volatile qualifiers can be
removed from the members of the NCR5380_hostdata struct. This is done in
a subsequent patch.
Proper locking will allow the abort handler to locate a command being
aborted. This is presently impossible if the abort handler is invoked when
the command has been moved from a queue to a pointer on the stack. (If
eh_abort_handler can't determine whether a command has been completed
or is still being processed then it can't decide whether to return
success or failure.)
The hostdata spin lock is now held when calling NCR5380_select() and
NCR5380_information_transfer(). Where possible, the lock is dropped for
polling and PIO transfers.
Clean up the now-redundant SELECT_ENABLE_REG writes, that used to provide
limited mutual exclusion between information_transfer() and reselect().
Accessing hostdata->connected without data races means taking the lock;
cleanup these accesses.
The new spin lock falls away for m68k and other UP builds, so this should
have little impact there. In the SMP case the new lock should be
uncontested even when the SCSI bus is contested.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove FLAG_DTC3181E. It was used to suppress a final Arbitration Lost
(SEL asserted) test that isn't actually needed. The test was suppressed
because it causes problems for DTC436 and DTC536 chips. It takes place
after the host wins arbitration, so SEL has been asserted. These chips
can't seem to tell whether it was the host or another bus device that
did so.
This questionable final test appears in a flow chart in an early NCR5380
datasheet. It was removed from later documents like the DP5380 datasheet.
By the time this final test takes place, the driver has already tested
the Arbitration Lost bit several times. The first test happens 3 us after
BUS FREE (or longer due to register access delays). The protocol requires
that a device stop signalling within 1.8 us after BUS FREE unless it won
arbitration, in which case it must assert SEL, which is detected 1.2 us
later by the first Arbitration Lost test.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target reports a QUEUE_FULL condition it causes the driver to
update the 'queue_size' limit with the number of currently allocated tags.
At least, that's what's supposed to happen, according to the comments.
Unfortunately the terms in the assignment are swapped. Fix this and
cleanup some obsolete comments.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing .module initializer. Use distinct .proc_name values for the
g_NCR5380 and g_NCR5380_mmio modules. Remove pointless CAN_QUEUE and
CMD_PER_LUN override macros. Cleanup whitespace and code style.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NDEBUG_NO_DATAOUT should not disable DATA IN phases too. Fix this.
(This bug has long been fixed in atari_NCR5380.c.)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes
needed by the core drivers into the common header (delay.h etc).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the array bounds check when transferring an extended message from the
target.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bring the two NCR5380_reselect() implementations into agreement.
Replace infinite loops in atari_NCR5380.c with timeouts, as per NCR5380.c.
Remove 'abort' flag in NCR5380.c as per atari_NCR5380.c -- if reselection
fails, there may be no MESSAGE IN phase so don't attempt data transfer.
During selection, don't interfere with the chip registers after a
reselection interrupt intervenes.
Clean up some trivial issues with code style, comments and printk.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The workarounds for chip errata appear twice, in slightly different
forms. One is used when defined(REAL_DMA) || defined(REAL_DMA_POLL), the
other when defined(PSEUDO_DMA). In the PDMA case, the workarounds have
been made conditional on FLAG_NO_DMA_FIXUPS. Do the same for the DMA case,
to eliminate the READ_OVERRUNS macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The flags DMA_WORKS_RIGHT, FLAG_NCR53C400 and FLAG_HAS_LAST_BYTE_SENT
all mean the same thing, i.e. the chip is not a 538[01]. (More recent
devices such as the 53C80 have a 'Last Byte Sent' bit in the Target
Command Register as well as other fixes for End-of-DMA errata.)
These flags have no additional meanings since previous cleanup patches
eliminated the NCR53C400 macro, moved g_NCR5380-specific code out of the
core driver and standardized interrupt handling.
Use the FLAG_NO_DMA_FIXUP flag to suppress End-of-DMA errata workarounds,
for those cards and drivers that make use of the TCR_LAST_BYTE_SENT bit.
Remove the old flags.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SCSI bus protocol sometimes requires monitoring two related conditions
simultaneously. Enhance NCR5380_poll_politely() for this purpose, and
put it to use in the arbitration algorithm. It will also find use in
pseudo DMA.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because interrupt handling is crucial to the core driver(s), all wrapper
drivers need to agree on this code. This patch removes discrepancies.
NCR5380_intr() in NCR5380.c has the following pointless loop that differs
from the code in atari_NCR5380.c.
done = 1;
do {
/* ... */
} while (!done);
The 'done' flag gets cleared when a reconnected command is to be processed
from the work queue. But in NCR5380.c, the flag is also used to cause the
interrupt conditions to be re-examined. Perhaps this was because
NCR5380_reselect() was expected to cause another interrupt, or perhaps
the remaining present interrupt conditions need to be handled after the
NCR5380_reselect() call?
Actually, both possibilities are bogus, as is the loop itself. It seems
have been overlooked in the hit-and-miss removal of scsi host instance
list iteration many years ago; see history/history.git commit 491447e1fcff
("[PATCH] next NCR5380 updates") and commit 69e1a9482e57 ("[PATCH] fix up
NCR5380 private data"). See also my earlier patch, "Always retry
arbitration and selection".
The datasheet says, "IRQ can be reset simply by reading the Reset
Parity/Interrupt Register". So don't treat the chip IRQ like a
level-triggered interrupt. Of the conditions that set the IRQ flag,
some are level-triggered and some are edge-triggered, which means IRQ
itself must be edge-triggered.
Some interrupt conditions are latched and some are not. Before clearing
the chip IRQ flag, clear all state that may cause it to be raised. That
means clearing the DMA Mode and Busy Monitor bits in the Mode Register
and clearing the host ID in the Select Enable register.
Also clean up some printk's and some comments. Keep atari_NCR5380.c and
NCR5380.c in agreement.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Configuring core drivers using macros like this one prevents re-unifying
the core driver forks, and prevents implementing the core driver as a
library or a platform driver.
The UNSAFE macro in particular is a poor workaround for the problem of
interrupt latency. Releasing the locks complicates things because then we
would have to handle the possibility of EH handler invocation during a
PDMA transfer.
The comments say that instead of using this macro, "you're going to be
better off twiddling with transfersize". I agree. Remove this stuff.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The complex main_running/queue_main mechanism is peculiar to
atari_NCR5380.c. It isn't SMP safe and offers little value given that
the work queue already offers concurrency management. Remove this
complexity to bring atari_NCR5380.c closer to NCR5380.c.
It is not a good idea to call the information transfer state machine from
queuecommand because, according to Documentation/scsi/scsi_mid_low_api.txt
that could happen in soft irq context. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each host instance now has it's own work queue so the main() work item can
sleep when necessary. That means we can use a simple work item rather than
a delayed work item. This brings NCR5380.c closer to atari_NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When there is a queued command and no connected command, NCR5380_select()
is called and arbitration begins. The chip waits for BUS FREE once the
MR_ARBITRATE bit in the mode register is enabled. That means there is
no need to wait for BUS FREE after disconnecting.
There is presently no polling for BUS FREE after sending an ABORT or
other message that might lead to disconnection. It only happens after
COMMAND COMPLETE or DISCONNECT messages, which seems inconsistent.
Remove the polling for !BSY in the COMMAND COMPLETE and DISCONNECT
cases.
BTW, the comments say "avoid nasty timeouts" and perhaps BUS FREE polling
was somehow helpful back in Linux v0.99.14u, when it was introduced.
The relevant timeout is presently 1 second (for bus arbitration).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow target selection to fail with a timeout instead of waiting in
infinite loops. This gets rid of the unused NCR_TIMEOUT macro, it is more
defensive and has proved helpful in debugging.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use timeouts in do_abort() in atari_NCR5380.c instead of infinite loops.
Also fix the kernel-doc comment. Keep the two core driver forks in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_poll_politely() returns either 0 (success) or -ETIMEDOUT. However,
in do_abort(), the return value is incorrectly taken to be the status
register value. This means that the bus is put into DATA OUT phase instead
of MESSAGE OUT. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_poll_politely() never returns -1. That means do_abort() can fail
to handle a timeout after waiting for the target to negate REQ. Fix this
and cleanup other NCR5380_poll_politely() call sites.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MESSAGE REJECT does not imply DISCONNECT: the target is about to enter
MESSAGE IN or MESSAGE OUT phase.
This bug fix comes from atari_NCR5380.c. Unfortunately it never made it
into the original NCR5380.c core driver.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some old drivers partially implemented support for linked commands using
a "proposed" next_link pointer in struct scsi_cmnd that never actually
existed. Remove this code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
