This patch enables lcd and backlight drivers in NURI board.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the parent clock for watchdog timer for EXYNOS4.
Signed-off-by: Inderpal Singh <inderpal.s@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The regulator API ifdefs itself out when not enabled
so there is no need for users to do this.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung ARMLEX4210 board support file
which is based on Exynos4210.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[kgene.kim@samsung.com: added clk_type for hsmmc3]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds basic definitions for MAX8952 & LP3974 (MAX8998
compatible) PMICs for UniversalC210 board. Power consumers for the
device drivers will be added later. These two PMICs occupy I2C5 bus.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung NURI board support.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes wrong constants in the hotplug assembly code for
Exynos4 such as Russell's changing in vexpress hotplug and fixes
hard-coded control register constatns also.
Reported-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes dependency of ARCH_EXYNOS4 from ARCH_S5PV310
according to the change of ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes dependency of ARCH_EXYNOS4 from ARCH_S5PV310
according to the change of ARCH name, EXYNOS4.
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates EXYNOS4 OneNAND support according to the change of
ARCH name, EXYNOS4.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the Kconfig and Makefile for the new ARCH_EXYNOS4.
It also updates arch/arm/Kconfig, Makeifile and arch/arm/mm/Kconfig
to include support for the new ARCH_EXYNOS4.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves board support files, SMDKC210, SMKDV310
and UNIVERSAL_C210 into arch/arm/mach-exynos4/ according
to the change of ARCH name, EXYNOS4.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates device support of EXYNOS4 according to the change of
ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds EXYNOS4 CPU support files in mach-exynos4,
and basically they are moved from mach-s5pv310 so that it
can support Samsung's new CPU name, EXYNOS4.
The EXYNOS4 ingegrates a ARM Cortex A9 multi-core.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Copy up lower inode attrs in getattr
ecryptfs: read on a directory should return EISDIR if not supported
eCryptfs: Handle NULL nameidata pointers
eCryptfs: Revert "dont call lookup_one_len to avoid NULL nameidata"
The current code does not follow Intel documentation: It misses some things
and does other, undocumented things. This causes wrong backlight values in
certain conditions. Instead of adding tricky code handling badly documented
and rare corner cases, don't handle combination mode specially at all. This
way PCI_LBPC is never touched and weird things shouldn't happen.
If combination mode is enabled, then the only downside is that changing the
brightness has a greater granularity (the LBPC value), but LBPC is at most
254 and the maximum is in the thousands, so this is no real functional loss.
A potential problem with not handling combined mode is that a brightness of
max * PCI_LBPC is not bright enough. However, this is very unlikely because
from the documentation LBPC seems to act as a scaling factor and doesn't look
like it's supposed to be changed after boot. The value at boot should always
result in a bright enough screen.
IMPORTANT: However, although usually the above is true, it may not be when
people ran an older (2.6.37) kernel which messed up the LBPC register, and
they are unlucky enough to have a BIOS that saves and restores the LBPC value.
Then a good kernel may seem to not work: Max brightness isn't bright enough.
If this happens people should boot back into the old kernel, set brightness
to the maximum, and then reboot. After that everything should be fine.
For more information see the below links. This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=23472http://bugzilla.kernel.org/show_bug.cgi?id=25072
Signed-off-by: Indan Zupancic <indan@nul.nu>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We force particular alignment when we generate attribute structures
when generation MODULE_VERSION() data and we need to make sure that
this alignment is followed when we iterate over these structures,
otherwise we may crash on platforms whose natural alignment is not
sizeof(void *), such as m68k.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
[ There are more issues here, but the fixes are incredibly ugly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the "log_buf_len" description to use [KMG] syntax for the
buffer size.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The '[KMG]' suffix is commonly described after a number of kernel
parameter values documentation. Explicitly state its semantics.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6745/1: kprobes insn decoding fix
ARM: tlb: move noMMU tlb_flush() to asm/tlb.h
ARM: tlb: delay page freeing for SMP and ARMv7 CPUs
ARM: Keep exit text/data around for SMP_ON_UP
ARM: Ensure predictable endian state on signal handler entry
ARM: 6740/1: Place correctly notes section in the linker script
ARM: 6700/1: SPEAr: Correct SOC config base address for spear320
ARM: 6722/1: SPEAr: sp810: switch to slow mode before reset
ARM: 6712/1: SPEAr: replace readl(), writel() with relaxed versions in uncompress.h
ARM: 6720/1: SPEAr: Append UL to VMALLOC_END
ARM: 6676/1: Correct the cpu_architecture() function for ARMv7
ARM: 6739/1: update .gitignore for boot/compressed
ARM: 6743/1: errata: interrupted ICALLUIS may prevent completion of broadcasted operation
ARM: 6742/1: pmu: avoid setting IRQ affinity on UP systems
ARM: 6741/1: errata: pl310 cache sync operation may be faulty
It is found on Dell Inspiron 1018 that the firmware reports that the hardware
killswitch is not supported. This makes the rfkill key not functional.
This patch forces the driver to toggle the firmware rfkill status in the case
that the hardware killswitch is indicated as unsupported by the firmware.
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Tested-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some thinkpad hotkeys report key codes like KEY_FN_F8 when something
like KEY_VOLUMEDOWN is desired. Always provide the scan codes in
addition to the key codes to assist with debugging these issues. Also
send the scan code before the key code to match what other drivers do,
as some userspace utilities expect this ordering.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
6AF4F258-B401-42fd-BE91-3D4AC2D7C0D3 needs to be
6AF4F258-B401-42FD-BE91-3D4AC2D7C0D3 to match the hardware alias.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: stable@kernel.org
Most platform/x86 drivers that use INPUT_SPARSEKMAP also depend on INPUT,
so do the same for ideapad-laptop. This fixes a kconfig warning and
subsequent build errors when CONFIG_INPUT is disabled.
warning: (ACER_WMI && ASUS_LAPTOP && DELL_WMI && HP_WMI && PANASONIC_LAPTOP && IDEAPAD_LAPTOP && EEEPC_LAPTOP && EEEPC_WMI && MSI_WMI && TOPSTAR_LAPTOP && ACPI_TOSHIBA) selects INPUT_SPARSEKMAP which has unmet direct dependencies (!S390 && INPUT)
ERROR: "input_free_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_register_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_setup" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_allocate_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_unregister_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_free" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_report_event" [drivers/platform/x86/ideapad-laptop.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is no need to install a chained handler for this hardware. This
is a plain x86 IOAPIC interrupt which is handled by the core code
perfectly fine. There is nothing special about demultiplexing these
gpio interrupts which justifies a custom hack. Replace it by a plain
old interrupt handler installed with request_irq. That makes the code
agnostic about the underlying primary interrupt hardware. The overhead
for this is minimal, but it gives us the advantage of accounting,
balancing and to detect interrupt storms. gpio interrupts are not
really that performance critical.
Patch fixups from akpm
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LANMAN response length was changed to 16 bytes instead of 24 bytes.
Revert it back to 24 bytes.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
CC: stable@kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
The lower filesystem may do some type of inode revalidation during a
getattr call. eCryptfs should take advantage of that by copying the
lower inode attributes to the eCryptfs inode after a call to
vfs_getattr() on the lower inode.
I originally wrote this fix while working on eCryptfs on nfsv3 support,
but discovered it also fixed an eCryptfs on ext4 nanosecond timestamp
bug that was reported.
https://bugs.launchpad.net/bugs/613873
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
read() calls against a file descriptor connected to a directory are
incorrectly returning EINVAL rather than EISDIR:
[EISDIR]
[XSI] [Option Start] The fildes argument refers to a directory and the
implementation does not allow the directory to be read using read()
or pread(). The readdir() function should be used instead. [Option End]
This occurs because we do not have a .read operation defined for
ecryptfs directories. Connect this up to generic_read_dir().
BugLink: http://bugs.launchpad.net/bugs/719691
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Marcin Slusarz says:
> In arch/arm/kernel/kprobes-decode.c there's a function
> arm_kprobe_decode_insn which does:
>
> } else if ((insn & 0x0e000000) == 0x0c400000) {
> ...
>
> This is always false, so code below is dead.
> I found this bug by coccinelle (http://coccinelle.lip6.fr/).
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to noMMU to put tlb_flush() in asm/tlbflush.h - it's
part of the tlb shootdown interface. Move it to asm/tlb.h instead, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to delay freeing any mapped page on SMP and ARMv7 systems to
ensure that the data is not accessed by other CPUs, or is used for
speculative prefetch with ARMv7. This includes not only mapped pages
but also pages used for the page tables themselves.
This avoids races with the MMU/other CPUs accessing pages after they've
been freed but before we've invalidated the TLB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Cc: <stable@kernel.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
