This simply makes the code easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves all register bit #defines which describe the (PHY
specific) bits in the RTL821x_INER right below the RTL821x_INER register
definition. This makes it easier to spot which registers and bits belong
together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This macro is only used by the RTL8211B code. RTL8211E and RTL8211F both
use other bits to initialize the RTL821x_INER register.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it easier to compare the #defines with the datasheets.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: cross-chip FDB support
DSA can have interconnected switches. For instance, the ZII Dev Rev B
board described in arch/arm/boot/dts/vf610-zii-dev-rev-b.dts has a
switch fabric composed of 3 switch devices like this:
lan4 lan6
CPU (eth1) | lan5 | lan7
| | | | |
[0 1 2 3 4 6 5]---[6 0 1 2 3 4 5]---[9 0 1 2 3 4 5 6 7 8]
| | | | | | |
lan0 | lan2 lan3 lan8 | optical4
lan1 optical3
One current issue with DSA is cross-chip FDB. If we add a static MAC
address on lan3, only its parent switch 1 (the one in the middle) will
be programmed. That is not correct in a cross-chip environment, because
the DSA ports connecting to switch 1 of adjacent switch 0 (on the left)
and switch 2 (on the right) must be programmed too.
Without this patchset, a dump of the hardware FDB of switches 0, 1 and 2
after programming a MAC address on lan3 looks like this (*):
# bridge fdb add 11:22:33:44:55:66 dev lan3
# cat /sys/kernel/debug/mv88e6xxx/sw*/atu/0 | grep -v FID
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n 0 - - - - - -
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6 7 8 9
With this patchset applied, adjacent DSA ports get programmed too:
# bridge fdb add 11:22:33:44:55:66 dev lan3
# cat /sys/kernel/debug/mv88e6xxx/sw*/atu/0 | grep -v FID
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n - - - - - 5 -
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n 0 - - - - - -
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n - - - - - - - - - 9
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6 7 8 9
In order to do that, the first commit introduces a dsa_towards_port()
helper which returns the local port of a switch which must be used to
reach an arbitrary switch port (local or from an adjacent switch.)
The second patch uses this helper to configure the port reaching the
target port for every switches of the fabric.
(*) a patch for squashed debugfs interface which applies on top of this
patchset is available here:
f8e6ba34c6.patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a MAC address is added to or removed from a switch port in the
fabric, the target switch must program its port and adjacent switches
must program their local DSA port used to reach the target switch.
For this purpose, use the dsa_towards_port() helper to identify the
local switch port which must be programmed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new helper returning the local port used to reach an arbitrary
switch port in the fabric.
Its only user at the moment is the dsa_upstream_port helper, which
returns the local port reaching the dedicated CPU port, but it will be
used in cross-chip FDB operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: simplify switchdev prepare phase
This patch series brings no functional changes.
It removes the unused switchdev_trans arguments from the dsa_switch_ops
for both MDB and VLAN operations, and provides functions to prepare and
add these objects for a given bitmap of ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the MDB code iterating on a multicast group into new
dsa_switch_mdb_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the VLAN code iterating on a list of VLAN members into new
dsa_switch_vlan_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from MDB prepare and add operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 3a927bc7cf ("ovs: propagate per dp max headroom to
all vports") the need_headroom for the internal vport is updated
accordingly to the max needed headroom in its datapath.
That avoids the pskb_expand_head() costs when sending/forwarding
packets towards tunnel devices, at least for some scenarios.
We still require such copy when using the ovs-preferred configuration
for vxlan tunnels:
br_int
/ \
tap vxlan
(remote_ip:X)
br_phy
\
NIC
where the route towards the IP 'X' is via 'br_phy'.
When forwarding traffic from the tap towards the vxlan device, we
will call pskb_expand_head() in vxlan_build_skb() because
br-phy->needed_headroom is equal to tun->needed_headroom.
With this change we avoid updating the internal vport needed_headroom,
so that in the above scenario no head copy is needed, giving 5%
performance improvement in UDP throughput test.
As a trade-off, packets sent from the internal port towards a tunnel
device will now experience the head copy overhead. The rationale is
that the latter use-case is less relevant performance-wise.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
net: ethernet: ti: cpsw/ale clean up and optimization
This is set of non critical clean ups and optimizations for TI
CPSW and ALE drivers.
Rebased on top on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE ports number includes the Host port and ext Ports, and
ALE ports numbering starts from 0, so correct corresponding port
checks in cpsw_ale_control_set/get().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move static initialization from cpsw_ale_start() to cpsw_ale_create() as it
does not make much sence to perform static initializtion in
cpsw_ale_start() which is called everytime netif[s] is opened.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale->params.ale_ports parameter can be used to deriver values for all
ale entry mask bits: port_mask_bits, port_mask_bits, port_num_bits.
Hence, calculate above values and drop all hardcoded values. For
port_num_bits calcualtion use order_base_2() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE is enabled from cpsw_ale_start() now, but disabled only from
cpsw_ale_destroy() which introduces inconsitance as cpsw_ale_start() is
called when netif[s] is opened, but cpsw_ale_destroy() is called when
driver is removed. Hence, move ALE disabling in cpsw_ale_stop().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI OMAP/Sitara SoCs have fixed number of ALE ports 3, which includes Host
port also.
Hence, use fixed value instead of value calcualted from DT, which can be
set by user and might not reflect actual HW configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused variable "poll" from cpsw_update_channels_res().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
read_status and config_aneg are the only mandatory callbacks and most
of the time the generic implementation is used by drivers.
So make the core fall back to the generic version if a driver doesn't
implement the respective callback.
Also currently the core doesn't seem to verify that drivers implement
the mandatory calls. If a driver doesn't do so we'd just get a NPE.
With this patch this potential issue doesn't exit any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu says:
====================
ip6_gre: add erspan native tunnel for ipv6
The patch series add support for ERSPAN tunnel over ipv6. The first patch
refectors the existing ipv4 gre implementation and the second refactors the
ipv6 gre's xmit code. Finally the last patch introduces erspan protocol.
change in v5:
- add cover-letter description
change in v4:
- rebase on top of net-next
- use log_ecn_error in ip6_tnl_rcv
change in v3:
- add inline for functions in header
- rebase on top of net-next
change in v2:
- remove inline
- fix some indent
- fix errors reports by clang and scan-build
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for ERSPAN tunnel over ipv6.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the ip6gre_xmit_{ipv4, ipv6}.
It is a prep work to add the ip6erspan tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move two erspan functions to header file, erspan.h, so ipv6
erspan implementation can use it.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Branden says:
====================
net: ethtool: add support for ETH_RESET_AP
Add support to reset appplication processors inside SmartNICs by
defining new ETH_RESET_AP bit.
And use new ETH_RESET_AP bit in bnxt ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETH_RESET_AP support handling to reset the internal
Application Processor(s) of the SmartNIC card.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETH_RESET_AP to reset the application processor(s) inside the NIC
interface.
Current ETH_RESET_MGMT supports a management processor inside this NIC.
This is typically used for remote NIC management purposes.
Application processors exist inside some SmartNICs to run various
applications inside the NIC processor - be it a simple algorithm without
an OS to as complex as hosting multiple VMs.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan says:
====================
rds-tcp netns delete related fixes
Patchset contains cleanup and bug fixes. Patch 1 is the removal
of some redundant code/functions. Patch 2 and 3 are fixes for
corner cases identified by syzkaller. I've not been able to
reproduce the actual use-after-free race flagged in the syzkaller
reports, thus these fixes are based on code inspection plus
manual testing to make sure the modified code paths are executed
without problems in the commonly encountered timing cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The rds_tcp_kill_sock() function parses the rds_tcp_conn_list
to find the rds_connection entries marked for deletion as part
of the netns deletion under the protection of the rds_tcp_conn_lock.
Since the rds_tcp_conn_list tracks rds_tcp_connections (which
have a 1:1 mapping with rds_conn_path), multiple tc entries in
the rds_tcp_conn_list will map to a single rds_connection, and will
be deleted as part of the rds_conn_destroy() operation that is
done outside the rds_tcp_conn_lock.
The rds_tcp_conn_list traversal done under the protection of
rds_tcp_conn_lock should not leave any doomed tc entries in
the list after the rds_tcp_conn_lock is released, else another
concurrently executiong netns delete (for a differnt netns) thread
may trip on these entries.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8edc3affc0 ("rds: tcp: Take explicit refcounts on struct net")
introduces a regression in rds-tcp netns cleanup. The cleanup_net(),
(and thus rds_tcp_dev_event notification) is only called from put_net()
when all netns refcounts go to 0, but this cannot happen if the
rds_connection itself is holding a c_net ref that it expects to
release in rds_tcp_kill_sock.
Instead, the rds_tcp_kill_sock callback should make sure to
tear down state carefully, ensuring that the socket teardown
is only done after all data-structures and workqs that depend
on it are quiesced.
The original motivation for commit 8edc3affc0 ("rds: tcp: Take explicit
refcounts on struct net") was to resolve a race condition reported by
syzkaller where workqs for tx/rx/connect were triggered after the
namespace was deleted. Those worker threads should have been
cancelled/flushed before socket tear-down and indeed,
rds_conn_path_destroy() does try to sequence this by doing
/* cancel cp_send_w */
/* cancel cp_recv_w */
/* flush cp_down_w */
/* free data structures */
Here the "flush cp_down_w" will trigger rds_conn_shutdown and thus
invoke rds_tcp_conn_path_shutdown() to close the tcp socket, so that
we ought to have satisfied the requirement that "socket-close is
done after all other dependent state is quiesced". However,
rds_conn_shutdown has a bug in that it *always* triggers the reconnect
workq (and if connection is successful, we always restart tx/rx
workqs so with the right timing, we risk the race conditions reported
by syzkaller).
Netns deletion is like module teardown- no need to restart a
reconnect in this case. We can use the c_destroy_in_prog bit
to avoid restarting the reconnect.
Fixes: 8edc3affc0 ("rds: tcp: Take explicit refcounts on struct net")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A side-effect of Commit c14b036681 ("rds: tcp: set linger to 1
when unloading a rds-tcp") is that we always send a RST on the tcp
connection for rds_conn_destroy(), so rds_tcp_conn_paths_destroy()
is not needed any more and is removed in this patch.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending node local messages the code is using an 'mtu' of 66060
bytes to avoid unnecessary fragmentation. During situations of low
memory tipc_msg_build() may sometimes fail to allocate such large
buffers, resulting in unnecessary send failures. This can easily be
remedied by falling back to a smaller MTU, and then reassemble the
buffer chain as if the message were arriving from a remote node.
At the same time, we change the initial MTU setting of the broadcast
link to a lower value, so that large messages always are fragmented
into smaller buffers even when we run in single node mode. Apart from
obtaining the same advantage as for the 'fallback' solution above, this
turns out to give a significant performance improvement. This can
probably be explained with the __pskb_copy() operation performed on the
buffer for each recipient during reception. We found the optimal value
for this, considering the most relevant skb pool, to be 3744 bytes.
Acked-by: Ying Xue <ying.xue@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafal Ozieblo says:
====================
Receive packets filtering for macb driver
This patch series adds support for receive packets
filtering for Cadence GEM driver. Packets can be redirect
to different hardware queues based on source IP, destination IP,
source port or destination port. To enable filtering,
support for RX queueing was added as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several reasons for increasing the receive ring sizes:
1. The original ring size of 256 was chosen about 10 years ago when
vmxnet3 was first created. At that time, 10Gbps Ethernet was not prevalent
and servers were dominated by 1Gbps Ethernet. Now 10Gbps is common place,
and higher bandwidth links -- 25Gbps, 40Gbps, 50Gbps -- are starting
to appear. 256 Rx ring entries are simply not enough to keep up with
higher link speed when there is a burst of network frames coming from
these high speed links. Even with full MTU size frames, they are gone
in a short time. It is also more common to have a mix of frame sizes,
and more likely bi-modal distribution of frame sizes so the average frame
size is not close to full MTU. If we consider average frame size of 800B,
1024 frames that come in a burst takes ~0.65 ms to arrive at 10Gbps. With
256 entires, it takes ~0.16 ms to arrive at 10Gbps. At 25Gbps or 40Gbps,
this time is reduced accordingly.
2. On a hypervisor where there are many VMs and CPU is over committed,
i.e. the number of VCPUs is more than the number of VCPUs, each PCPU is
in effect time shared between multiple VMs/VCPUs. The time granularity at
which this multiplexing occurs is typically coarser than between processes
on a guest OS. Trying to time slice more finely is not efficient, for
example, if memory cache is barely warmed up when switching from one VM
to another occurs. This CPU overcommit adds delay to when the driver
in a VM can service incoming packets. Whether CPU is over committed
really depends on customer workloads. For certain situations, it is very
common. For example, workloads of desktop VMs and product testing setups.
Consolidation and sharing is what drives efficiency of a customer setup
for such workloads. In these situations, the raw network bandwidth may
not be very high, but the delays between when a VM is running or not
running can also be relatively long.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Acked-by: Jin Heo <heoj@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Acked-by: Boon Ang <bang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the much more capable b53_get_tag_protocol() which takes care of
all Broadcom switches specifics to resolve which port can have Broadcom
tags enabled or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e32ea7e747 ("soreuseport: fast reuseport UDP socket
selection") and commit c125e80b88 ("soreuseport: fast reuseport
TCP socket selection") the relevant reuseport socket matching the current
packet is selected by the reuseport_select_sock() call. The only
exceptions are invalid BPF filters/filters returning out-of-range
indices.
In the latter case the code implicitly falls back to using the hash
demultiplexing, but instead of selecting the socket inside the
reuseport_select_sock() function, it relies on the hash selection
logic introduced with the early soreuseport implementation.
With this patch, in case of a BPF filter returning a bad socket
index value, we fall back to hash-based selection inside the
reuseport_select_sock() body, so that we can drop some duplicate
code in the ipv4 and ipv6 stack.
This also allows faster lookup in the above scenario and will allow
us to avoid computing the hash value for successful, BPF based
demultiplexing - in a later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not supported anymore, devices needing a MAC address
just assign one at random, it's just a driver pecularity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Miller says:
====================
net: Significantly shrink the size of routes.
Through a combination of several things, our route structures are
larger than they need to be.
Mostly this stems from having members in dst_entry which are only used
by one class of routes. So the majority of the work in this series is
about "un-commoning" these members and pushing them into the type
specific structures.
Unfortunately, IPSEC needed the most surgery. The majority of the
changes here had to do with bundle creation and management.
The other issue is the refcount alignment in dst_entry. Once we get
rid of the not-so-common members, it really opens the door to removing
that alignment entirely.
I think the new layout looks really nice, so I'll reproduce it here:
struct net_device *dev;
struct dst_ops *ops;
unsigned long _metrics;
unsigned long expires;
struct xfrm_state *xfrm;
int (*input)(struct sk_buff *);
int (*output)(struct net *net, struct sock *sk, struct sk_buff *skb);
unsigned short flags;
short obsolete;
unsigned short header_len;
unsigned short trailer_len;
atomic_t __refcnt;
int __use;
unsigned long lastuse;
struct lwtunnel_state *lwtstate;
struct rcu_head rcu_head;
short error;
short __pad;
__u32 tclassid;
(This is for 64-bit, on 32-bit the __refcnt comes at the very end)
So, the good news:
1) struct dst_entry shrinks from 160 to 112 bytes.
2) struct rtable shrinks from 216 to 168 bytes.
3) struct rt6_info shrinks from 384 to 320 bytes.
Enjoy.
v2:
Collapse some patches logically based upon feedback.
Fix the strange patch #7.
v3: xfrm_dst_path() needs inline keyword
Properly align __refcnt on 32-bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While building ipsec bundles, blocks of xfrm dsts are linked together
using dst->next from bottom to the top.
The only thing this is used for is initializing the pmtu values of the
xfrm stack, and for updating the mtu values at xfrm_bundle_ok() time.
The bundle pmtu entries must be processed in this order so that pmtu
values lower in the stack of routes can propagate up to the higher
ones.
Avoid using dst->next by simply maintaining an array of dst pointers
as we already do for the xfrm_state objects when building the bundle.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
