Add framework for supporting geometrical occluders within rooms, and add support for sphere occluders.
Includes gizmos for editing.
They also work outside the portal system.
Applying the platform velocity when leaving the platform floor should be
done after snapping to keep things consistent.
Now it's done in both 2D and 3D, as it's already done in 2D on master.
Same thing that was already done in 2D, applies moving platform motion
by using a call to move_and_collide that excludes the platform itself,
instead of making it part of the body motion.
Helps with handling walls and slopes correctly when the character walks
on the moving platform.
Also made some minor adjustments to the 2D version and documentation.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
When synchronizing KinematicBody motion with moving the platform using
direct body state, only the linear velocity was taken into account.
This change exposes velocity at local point in direct body state and
uses it in move_and_slide to get the proper velocity that includes
rotations.
Fixed a bug in the complex PVS generation which was causing recursive loop.
Move some of the settings out of RoomManager into Project Settings.
Allow PVS generation method to be selected from Project Settings, and control PVS logging.
The checking for link room IDs was checking for less than size(), but was not correctly checking for -1,
and therefore reading outside the array range. This PR fixes this.
Portal autolinking was previously agnostic to room priorities, which meant that portals would link to the first room they found (often outside rooms). This PR fixes this by making the autolinking priority aware, and will preferentially link to internal rooms.
Fixes a bug whereby it read from the primary PVS in the gameplay monitor, using the size from the secondary PVS. This would read out of bounds and crash.
Removed debug code to update the gameplay monitor from the preview camera - this is no longer required.
Temporarily revert to the simple PVS generation method, because I've noticed a bug in the complex version, and the simple version is safer while I fix this.
Calling rooms_set_active with TOOLS_ENABLED from a running project resulted in a crash because the Spatial Editor is not available. Wrapped it in an is_editor_hint.
In response to user demand, the naming convention for importing levels from blender etc is changed from prefixes `Room_` and `Portal_` to postfixes `-room`, `-roomgroup`, `-portal`.
The use of special prefixes is only actually required during the import phase - the first conversion of rooms, roomgroups, and portals from Spatials and MeshInstances (based on the workflow of importing from blender).
Once converted to the native Godot nodes there is no longer a need for the naming requirements.
This PR removes the requirements except for the import. Manual portal linking after the initial conversion is now done exclusively using the `linked_room` nodepath property of the Portal.
This PR makes the 'convert rooms' button permanently on the toolbar and accessible whichever node is selected, so you can convert rooms without having to select the RoomManager first.
It also adds a togglable item 'view portal culling' to the 'View' menu which is a simple way of setting the RoomManager 'active' setting without the RoomManager being the selected node.
Both of these have keyboard shortcuts, which should make it much faster to reconvert rooms and edit.
In addition there the string in the 'Perspective' Listbox is modified to show [portals active] when portal culling is operational, for visual feedback. This is updated when you change modes, and when the rooms are invalidated.
Implement Octahedral Compression for normal/tangent vectors
*Oct32 for uncompressed vectors
*Oct16 for compressed vectors
Reduces vertex size for each attribute by
*Uncompressed: 12 bytes, vec4<float32> -> vec2<unorm16>
*Compressed: 2 bytes, vec4<unorm8> -> vec2<unorm8>
Binormal sign is encoded in the y coordinate of the encoded tangent
Added conversion functions to go from octahedral mapping to cartesian
for normal and tangent vectors
sprite_3d and soft_body meshes write to their vertex buffer memory
directly and need to convert their normals and tangents to the new oct
format before writing
Created a new mesh flag to specify whether a mesh is using octahedral
compression or not
Updated documentation to discuss new flag/defaults
Created shader flags to specify whether octahedral or cartesian vectors
are being used
Updated importers to use octahedral representation as the default format
for importing meshes
Updated ShaderGLES2 to support 64 bit version codes as we hit the limit
of the 32-bit integer that was previously used as a bitset to store
enabled/disabled flags
If the user changed the portal Z scale in the editor the portal margin display could become incorrectly sized.
This is because the portal margin is measured in world space units, and has to be back calculated into model space using the inverse global transform of the portal node. The model space size of the margin is thus tied to the current scale of the node.
This PR forces updating the gizmo each time the transform is changed. This isn't super efficient, but as this is an editor only feature it should be okay, and it is unlikely to be a performance problem.
Due to a quirk in CSG Shapes, updating is usually deferred to the next frame. This is problematic as we need to read back the geometry on the first frame when converting levels.
This PR adds a function to CSGShape to force immediate updating (if dirty), and calls it during room conversion.
The default autoplace algorithm places instances in the highest priority Room. It became apparent that there are some situations in which users will want to override this and force placement in a Room from a particular RoomGroup, especially an "outside" RoomGroup.
This setting allows the user to specify a preference for Room priority. When set to 0, the setting is ignored and the highest priority Room is chosen.
Although explicit portals did a check to detect internal portals, this check was missing from autolinked portals. This meant they were incorrectly clipping the room bounds of the enclosing outer room.
This PR adds a check for internal rooms during the autolinking and sets the internal flag where needed.
The default portal margin is stored in the RoomManager. Previously this was propagated to Portals when the value was changed, and Portals each stored this default value.
This caused a bug during loading, if the RoomManager was loaded before Portals, the value was never propagated.
This PR makes the default margin a static value stored in the RoomManager, and the Portals now read directly from the static value when required, and do not store locally. This gets around the problem.
Higher values will make indirect lighting brighter.
A value of 1.0 represents physically accurate behavior, but higher values
can be used to make indirect lighting propagate more visibly when using
a low number of bounces.
This can be used to speed up bake times by lowering the number of bounces
then increasing the bounce indirect energy. Unlike BakedLightmapData's
energy property, this property does not affect direct lighting
emitted by light nodes or emissive materials.
Due to an oversight in the autoplace recursive search for static objects, static objects were getting added twice to the portal renderer, which meant they were being rendered twice, lowering performance.
This PR corrects this horrendous error.
Allows users to have the RoomManager as the roomlist.
Fixes a couple of bugs dealing with situations where users attempt to link Portals to Rooms outside the roomlist.
Adds a PortalEditorPlugin allowing you to flip individual portals.
In order to make level building easier, the system can now support STATIC and DYNAMIC objects in the roomlist that are not placed in rooms. The system will automatically place them in the appropriate room.
* Safe and unsafe motion are calculated by dichotomy with a limited
number of steps. It's good for performance, but on long motions that
either collide near the beginning or near the end, the result can be
very imprecise.
* Now a factor 0.25 or 0.75 is used to converge faster when this case
happens, which allows longer motions to get more accurate collision
detection.
* Makes snap collision more precise, and helps with cases where diagonal collision on the border of a platform can lead to the character being stuck.
Additional improvements to move_and_slide:
* Handle slide canceling in move_and_collide with 0 velocity instead of
not applying it.
* Better handling of snap with custom logic to cancel sliding.
* Remove small jittering when using stop on slope, by canceling the
motion completely when the resulting motion is less than margin instead
of always projecting to the up direction (in both body motion and snap).
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
Make sure the direction of the motion is preserved, unless the depth is
higher than the margin, which means the body needs depenetration in any
direction.
Also changed move_and_slide to avoid sliding on the first motion, in
order to avoid issues with unstable position on ground when jumping.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
- Specular can now be set above 1.0.
- Some properties now allow more precise values.
- The Bake Mode property hint was changed to be more descriptive.
- The maximum shadow bias values were adjusted to follow the property
hints in `master`.
It turned out the new autolinking feature was linking portals AFTER the static meshes had been added to rooms in the PortalRenderer. This meant that large meshes weren't being sprawled across these portals. The fix involves doing the autolinking BEFORE adding the static meshes.
Fixes a bug in the warning for portals being in the wrong direction, they should have only been checkout for outgoing portals. This was resulting in erroneous warnings.
Also the room conversion logs are refined to be more compact and informative.
A warning icon is also added in the gizmo for portals where autolink fails.
Clean: remove duplicate and interior vertices (uses Bullet algorithm)
Simplify: modify the geometry for further simplification (uses VHACD
algorithm)
In the editor, single convex hull now uses the clean option.
Added a new editor entry to create a simplified convex hull, can be
useful for creating convex hull from highly tessellated triangle meshes.
Specific change for 3.x:
Add support for Vector<Vector3> and PoolVector<Vector3> in the convex hull generator.
This backports the improved RayCast debug drawing functionality
from the `master` branch.
`ArrayMesh.clear_surfaces()` was also backported from the `master`
branch and exposed because the new debug drawing code requires it.
Although the visibility enabler worked to turn on and off AnimationPlayer as it enters and exits the view frustum, this was of little use as bones animation and especially software skinning still take place driven by the AnimationTree node.
This PR adds the ability to turn on and off AnimationTree, and AnimationTreePlayer nodes as they enter or exit the view frustum, which achieves the intention of switching off expensive animation processing.
This commits adds a new emitter type for particles material
and 3D CPU particles. The new emitter is called "ring"
and it can emit either in a ring or cylinder fashion.
This adds the following properties for the emitter:
1. ring_emitter_axis: the axis along which the ring/cylinder
will be constructed
2. ring_emitter_radius: outer radius of the ring/cylinder
3. ring_emitter_inner_radius: inner radius of the cylinder.
when set to zero, particles will emit in the full volume.
4. ring_emitter_height: height of the ring/cylinder emitter.
Co-authored-by: Rémi Verschelde <rverschelde@gmail.com>
